Bonjour, Sur une carte de type WAFER-LX800 (Geoge à 500Mhz avec 128Mo de Ram), j'ai installé via un cd net-install une version etch avec un noyau dans la famille des 2.6.17 => pas de Pb cela fonctionne.
Lorsque je la bascule sur un noyau de type lenny 2.6.18-4 (via un apt-get dist-upgrade), au démarrage suivant la carte se gèle juste après GRUB avec comme dernier message : sauve default Avec le 2.6.17 pas de Pb le démarrage continu. Là je sèche... Merci du coup de main. Yann. Ref : La carte cpu http://www.aplus-sa.com/datasht/WAFER-LX.pdf Un dmesg lorsque cela fonctionne ------------DMESG --------------- Linux version 2.6.17-2-486 (Debian 2.6.17-9) ([EMAIL PROTECTED]) (gcc version 4.1.2 20060901 (prerelease) (Debian 4.1.1-13)) #1 Wed Sep 13 15:56:30 UTC 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009c000 (usable) BIOS-e820: 000000000009c000 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 00000000077c0000 (usable) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 119MB LOWMEM available. On node 0 totalpages: 30656 DMA zone: 4096 pages, LIFO batch:0 Normal zone: 26560 pages, LIFO batch:7 DMI 2.2 present. ACPI: Unable to locate RSDP Allocating PCI resources starting at 10000000 (gap: 077c0000:f8830000) Built 1 zonelists Kernel command line: root=/dev/sda1 ro No local APIC present or hardware disabled mapped APIC to ffffd000 (010f1000) Initializing CPU#0 PID hash table entries: 512 (order: 9, 2048 bytes) Detected 498.139 MHz processor. Using tsc for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 114332k/122624k available (1456k kernel code, 7732k reserved, 566k data, 252k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 998.36 BogoMIPS (lpj=1996722) Security Framework v1.0.0 initialized SELinux: Disabled at boot. Capability LSM initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: 0088a93d c0c0a13d 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 0088a93d c0c0a13d 00000000 00000000 00000000 00000000 00000000 CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line) CPU: L2 Cache: 128K (32 bytes/line) CPU: After all inits, caps: 0088a93d c0c0a13d 00000000 00000000 00000000 00000000 00000000 CPU: AMD Geode(TM) Integrated Processor by AMD PCS stepping 02 Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 0k freed checking if image is initramfs... it is Freeing initrd memory: 4136k freed NET: Registered protocol family 16 EISA bus registered PCI: PCI BIOS revision 2.10 entry at 0xfa930, last bus=0 Setting up standard PCI resources ACPI: Subsystem revision 20060127 ACPI: Interpreter disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI: disabled PnPBIOS: Scanning system for PnP BIOS support... PnPBIOS: Found PnP BIOS installation structure at 0xb00fb2c0 PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xb2f0, dseg 0xf0000 PnPBIOS: 14 nodes reported by PnP BIOS; 14 recorded by driver PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) Boot video device is 0000:00:01.1 PCI: Ignore bogus resource 6 [0:0] of 0000:00:01.1 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 4096 bind 2048) TCP reno registered audit: initializing netlink socket (disabled) audit(1183138036.620:1): initialized VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A serial8250: ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize PNP: PS/2 Controller [PNP0303] at 0x60,0x64 irq 1 PNP: PS/2 controller doesn't have AUX irq; using default 12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 EISA: Probing bus 0 at eisa.0 Cannot allocate resource for EISA slot 1 Cannot allocate resource for EISA slot 6 EISA: Detected 0 cards. TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 8 NET: Registered protocol family 20 Using IPI Shortcut mode Freeing unused kernel memory: 252k freed input: AT Translated Set 2 keyboard as /class/input/input0 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx AMD5536: IDE controller at PCI slot 0000:00:0f.2 AMD5536: chipset revision 1 AMD5536: not 100% native mode: will probe irqs later AMD5536: 0000:00:0f.2 (rev 01) UDMA100 controller ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:pio, hdb:DMA Probing IDE interface ide0... SCSI subsystem initialized 8139too Fast Ethernet driver 0.9.27 usbcore: registered new driver usbfs usbcore: registered new driver hub libata version 1.20 loaded. ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) hdb: LTN485S, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 eth0: RealTek RTL8139 at 0xf400, 00:08:9b:69:c7:f0, IRQ 5 eth0: Identified 8139 chip type 'RTL-8100B/8139D' eth1: RealTek RTL8139 at 0xf600, 00:08:9b:69:c7:ef, IRQ 10 eth1: Identified 8139 chip type 'RTL-8100B/8139D' 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004) sata_uli 0000:00:11.0: version 0.5 ata1: SATA max UDMA/133 cmd 0xFD00 ctl 0xFC02 bmdma 0xF900 irq 11 ata2: SATA max UDMA/133 cmd 0xFB00 ctl 0xFA02 bmdma 0xF908 irq 11 hdb: ATAPI 48X CD-ROM drive, 120kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 ata1: SATA link up 1.5 Gbps (SStatus 113) ata1: dev 0 cfg 49:2f00 82:346b 83:7fe9 84:4773 85:3469 86:3c01 87:4763 88:407f ata1: dev 0 ATA-7, max UDMA/133, 160836480 sectors: LBA48 ata1: dev 0 configured for UDMA/133 scsi0 : sata_uli ata2: SATA link down (SStatus 0) scsi1 : sata_uli Vendor: ATA Model: HDS728080PLA380 Rev: PF2O Type: Direct-Access ANSI SCSI revision: 05 PCI: Setting latency timer of device 0000:00:0f.5 to 64 ehci_hcd 0000:00:0f.5: EHCI Host Controller ehci_hcd 0000:00:0f.5: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:0f.5: irq 9, io mem 0xefffd000 ehci_hcd 0000:00:0f.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 4 ports detected SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sd 0:0:0:0: Attached scsi disk sda PCI: Setting latency timer of device 0000:00:0f.4 to 64 ohci_hcd 0000:00:0f.4: OHCI Host Controller ohci_hcd 0000:00:0f.4: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:0f.4: irq 9, io mem 0xefffe000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 4 ports detected EXT3-fs: INFO: recovery required on readonly filesystem. EXT3-fs: write access will be enabled during recovery. kjournald starting. Commit interval 5 seconds EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. input: PC Speaker as /class/input/input1 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:0f: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:10: ttyS2 at I/O 0x3e8 (irq = 5) is a 16550A parport: PnPBIOS parport detected. parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] PCI: Setting latency timer of device 0000:00:0f.3 to 64 hw_random hardware driver 1.0.0 loaded Real Time Clock Driver v1.12ac EXT3 FS on sda1, internal journal loop: loaded (max 8 devices) device-mapper: 4.6.0-ioctl (2006-02-17) initialised: [EMAIL PROTECTED] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver eth0: no IPv6 routers present ohci_hcd 0000:00:0f.4: wakeup usb 2-1: new full speed USB device using ohci_hcd and address 2 usb 2-1: configuration #1 chosen from 1 choice i2c /dev entries driver ------------/DMESG---------------
