On Thu, Apr 27, 2006 at 10:14:48AM -0400, Toni L. Harbaugh-Blackford [Contr] wrote: > On Thu, 27 Apr 2006, Sven Luther wrote: > > > > > > > Is this in the debian docs, or is there a reference somewhere to how > > > to do it? If not, can you just give me a quick overview so I can > > > figure out how to do it? > > > > the debian-installer documentation used to have some (incomplete) > guidelines > > to do this, not sure where they are now. The s390 installer guide sahould > help > > you since they have neither display nor serial console. > > > > > I know SuSE provides this via linuxrc, but I was not aware that debian > > > did something similar. > > > > Well, it is a d-i feature, you use preseeding together with the ssh remote > > console. > > > > I don't see any mention of this in the s390 manual. The only description > that seems relevant indicates that the installation system has to successfully > boot before the network interface can be configured, which does not > happen in this case.
Ask the d-i folk, they should know. look at the preseed stuff in the documentation or something too, that is what i did. > > What is supposed to happen after 'Trying to im_free...' ? Attaching the full log. The isa stuff is probably related to the graphic card. Friendly, Sven Luther
Page orders: linear mapping = 24, others = 12 Found initrd at 0xc000000001a00000:0xc000000001f2c400 Found U3 memory controller & host bridge @ 0xf8000000 revision: 0x35 Mapped at 0xd000080080000000 Found a K2 mac-io controller, rev: 96, mapped at 0xd000080080041000 PowerMac motherboard: XServe G5 DART: table not allocated, using direct DMA Starting Linux PPC64 #2 SMP Tue Apr 25 15:35:40 CEST 2006 ----------------------------------------------------- ppc64_pft_size = 0x0 ppc64_interrupt_controller = 0x1 platform = 0x400 physicalMemorySize = 0x40000000 ppc64_caches.dcache_line_size = 0x80 ppc64_caches.icache_line_size = 0x80 htab_address = 0xc00000003e000000 htab_hash_mask = 0x1ffff ----------------------------------------------------- [boot]0100 MM Init [boot]0100 MM Init Done Linux version 2.6.16-1-vserver-powerpc64 (Debian 2.6.16-10) ([EMAIL PROTECTED]) (gcc version 4.0.3 (Debian 4.0.3-1)) #2 SMP Tue Apr 25 15:35:40 CEST 2006 [boot]0012 Setup Arch Top of RAM: 0x40000000, Total RAM: 0x40000000 Memory hole size: 0MB Found U3-AGP PCI host bridge. Firmware bus number: 240->255 Can't get bus-range for /[EMAIL PROTECTED],f2000000, assume bus 0 Found U3-HT PCI host bridge. Firmware bus number: 0->239 PCI Host 0, io start: 400000; io end: bfffff PCI Host 1, io start: 0; io end: 3fffff via-pmu: Server Mode is disabled PMU driver v2 initialized for Core99, firmware: 0c nvram: Checking bank 0... nvram: gen0=412, gen1=411 nvram: Active bank is: 0 nvram: OF partition at 0x410 nvram: XP partition at 0x1020 nvram: NR partition at 0x1120 On node 0 totalpages: 262144 DMA zone: 262144 pages, LIFO batch:31 DMA32 zone: 0 pages, LIFO batch:0 Normal zone: 0 pages, LIFO batch:0 HighMem zone: 0 pages, LIFO batch:0 [boot]0015 Setup Done Built 1 zonelists Kernel command line: root=/dev/sda4 ro mpic: Setting up MPIC " MPIC 1 " version 1.2 at 80040000, max 4 CPUs mpic: ISU size: 120, shift: 7, mask: 7f mpic: Initializing for 120 sources mpic: Setting up MPIC " MPIC 2 " version 1.2 at f8040000, max 4 CPUs mpic: ISU size: 124, shift: 7, mask: 7f mpic: Initializing for 124 sources PID hash table entries: 4096 (order: 12, 131072 bytes) time_init: decrementer frequency = 33.333333 MHz time_init: processor frequency = 2300.000000 MHz Console: colour dummy device 80x25 Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) freeing bootmem node 0 Memory: 1004136k/1048576k available (3472k kernel code, 44440k reserved, 932k data, 305k bss, 244k init) Calibrating delay loop... 66.56 BogoMIPS (lpj=33280) Security Framework v1.0.0 initialized SELinux: Disabled at boot. Capability LSM initialized Mount-cache hash table entries: 256 PowerMac SMP probe found 2 cpus KeyWest i2c @0xf8001003 irq 128 /[EMAIL PROTECTED],f8000000/[EMAIL PROTECTED] channel 0 bus <multibus> channel 1 bus <multibus> KeyWest i2c @0x80018000 irq 26 /[EMAIL PROTECTED],f2000000/[EMAIL PROTECTED]/[EMAIL PROTECTED]/[EMAIL PROTECTED] channel 0 bus <multibus> PMU i2c /[EMAIL PROTECTED],f2000000/[EMAIL PROTECTED]/[EMAIL PROTECTED]/[EMAIL PROTECTED]/pmu-i2c channel 1 bus <multibus> channel 2 bus <multibus> Processor timebase sync using Pulsar i2c clock requesting IPIs ... IPIs requested... Processor 1 found. Brought up 2 CPUs migration_cost=712 checking if image is initramfs... it is Freeing initrd memory: 5297k freed NET: Registered protocol family 16 PCI: Probing PCI hardware mapping IO f0000000 -> d000080000400000, size: 800000 mapping IO f4000000 -> d000080000000000, size: 400000 PCI: Probing PCI hardware done Registering pmac pic with sysfs... nvram_init: Could not find nvram partition for nvram buffered error logging. audit: initializing netlink socket (disabled) audit(1146164324.691:1): initialized VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered radeonfb: Found Open Firmware ROM Image radeonfb: Retrieved PLL infos from Open Firmware radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=150.00 Mhz, System=150.00 MHz radeonfb: PLL min 12000 max 35000 radeonfb: Monitor 1 type CRT found radeonfb: EDID probed radeonfb: Monitor 2 type no found Trying to im_free nonexistent area (d0000800800c1000) Console: switching to colour frame buffer device 128x48 radeonfb (0001:06:03.0): ATI Radeon QY vio_register_driver: driver hvc_console registering HVSI: registered 0 devices Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled pmac_zilog: 0.6 (Benjamin Herrenschmidt <[EMAIL PROTECTED]>) pmac_zilog: Error registering serial device, disabling pmac_zilog. pmac_zilog: Did another serial driver already claim the minors? Trying to im_free nonexistent area (d00008008216c000) Trying to im_free nonexistent area (d00008008216e000) isa bounce pool size: 16 pages RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize vroot: loaded (max 8 devices) MacIO PCI driver attached to K2 chipset Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx PCI: Enabling device: (0001:03:0d.0), cmd 16 ide0: Found Apple K2 ATA-6 controller, bus ID 3, irq 39 Probing IDE interface ide0... hda: MATSHITADVD-R UJ-845, ATAPI CD/DVD-ROM drive hda: Enabling Ultra DMA 2 ide0 at 0xd000080083258000-0xd000080083258007,0xd000080083258160 on irq 39 mice: PS/2 mouse device common for all mice NET: Registered protocol family 2 IP route cache hash table entries: 65536 (order: 7, 524288 bytes) TCP established hash table entries: 262144 (order: 10, 4194304 bytes) TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Freeing unused kernel memory: 244k freed PowerMac G5 Thermal control driver 1.2b2 Detected fan controls: 0: PWM fan, id 1, location: BACKSIDE,SYS CTRLR FAN 1: RPM fan, id 2, location: DRIVE BAY 2: PWM fan, id 2, location: SLOT,PCI FAN 3: RPM fan, id 3, location: CPU A INTAKE 4: RPM fan, id 4, location: CPU A EXHAUST 5: RPM fan, id 5, location: CPU B INTAKE 6: RPM fan, id 6, location: CPU B EXHAUST 9: RPM fan, id 1, location: CPU A 1 10: RPM fan, id 2, location: CPU A 2 11: RPM fan, id 3, location: CPU A 3 12: RPM fan, id 4, location: CPU B 1 13: RPM fan, id 5, location: CPU B 2 14: RPM fan, id 6, location: CPU B 3 hda: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 ieee1394: Initialized config rom entry `ip1394' tg3.c:v3.49 (Feb 2, 2006) eth0: Tigon3 [partno(BCM95704A6) rev 2003 PHY(5704)] (PCIX:133MHz:64-bit) 10/100/1000BaseT Ethernet 00:0d:93:9d:dd:ce eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1] eth0: dma_rwctrl[769f4000] dma_mask[32-bit] eth1: Tigon3 [partno(BCM95704A6) rev 2003 PHY(5704)] (PCIX:133MHz:64-bit) 10/100/1000BaseT Ethernet 00:0d:93:9d:dd:cf eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1] eth1: dma_rwctrl[769f4000] dma_mask[32-bit] SCSI subsystem initialized libata version 1.20 loaded. sata_svw 0001:05:0c.0: version 1.07 ata1: SATA max UDMA/133 cmd 0xD00008008327A000 ctl 0xD00008008327A020 bmdma 0xD00008008327A030 irq 0 ata2: SATA max UDMA/133 cmd 0xD00008008327A100 ctl 0xD00008008327A120 bmdma 0xD00008008327A130 irq 0 ata3: SATA max UDMA/133 cmd 0xD00008008327A200 ctl 0xD00008008327A220 bmdma 0xD00008008327A230 irq 0 ata4: SATA max UDMA/133 cmd 0xD00008008327A300 ctl 0xD00008008327A320 bmdma 0xD00008008327A330 irq 0 usbcore: registered new driver usbfs usbcore: registered new driver hub ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ata1: SATA link up 1.5 Gbps (SStatus 113) ata1: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4673 85:7c69 86:3e01 87:4663 88:007f ata1: dev 0 ATA-7, max UDMA/133, 160836480 sectors: LBA48 ata1: dev 0 configured for UDMA/133 scsi0 : sata_svw ata2: SATA link down (SStatus 4) scsi1 : sata_svw ata3: SATA link down (SStatus 4) scsi2 : sata_svw ata4: SATA link down (SStatus 4) scsi3 : sata_svw Vendor: ATA Model: Maxtor 6B080M0 Rev: BANC Type: Direct-Access ANSI SCSI revision: 05 PCI: Enabling device: (0001:03:0e.0), cmd 2 ohci1394: fw-host0: Unexpected PCI resource length of 1000! ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[40] MMIO=[80200000-802007ff] Max Packet=[4096] IR/IT contexts=[8/8] PCI: Enabling device: (0001:02:0b.0), cmd 2 ohci_hcd 0001:02:0b.0: OHCI Host Controller ohci_hcd 0001:02:0b.0: new USB bus registered, assigned bus number 1 ohci_hcd 0001:02:0b.0: irq 63, io mem 0x80102000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected PCI: Enabling device: (0001:02:0b.1), cmd 2 ohci_hcd 0001:02:0b.1: OHCI Host Controller ohci_hcd 0001:02:0b.1: new USB bus registered, assigned bus number 2 ohci_hcd 0001:02:0b.1: irq 63, io mem 0x80101000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected PCI: Enabling device: (0001:02:0b.2), cmd 6 ehci_hcd 0001:02:0b.2: EHCI Host Controller ehci_hcd 0001:02:0b.2: new USB bus registered, assigned bus number 3 ehci_hcd 0001:02:0b.2: irq 63, io mem 0x80100000 ehci_hcd 0001:02:0b.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 5 ports detected SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: [mac] sda1 sda2 sda3 sda4 sda5 sda6 sd 0:0:0:0: Attached scsi disk sda ieee1394: Host added: ID:BUS[0-01:1023] GUID[001124fffe4531cc] kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. usb 2-2: new low speed USB device using ohci_hcd and address 2 usb 2-2: configuration #1 chosen from 1 choice Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected Apple U3H chipset agpgart: configuring for size idx: 64 agpgart: AGP aperture is 256M @ 0x0 eth1394: eth2: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0) hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad? hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad? hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad? hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad? usbcore: registered new driver hiddev input: Logitech USB Receiver as /class/input/input0 input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0001:02:0b.1-2 input: Logitech USB Receiver as /class/input/input1 input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0001:02:0b.1-2 usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver EXT3 FS on sda4, internal journal ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1) ieee1394: sbp2: Try serialize_io=0 for better performance tg3: eth0: Link is up at 100 Mbps, full duplex. tg3: eth0: Flow control is on for TX and on for RX. NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver eth0: no IPv6 routers present
