On Monday 10 January 2005 11:42, Philippe Guyot wrote: > On Monday 10 January 2005 11:44, Sven Luther wrote: > > On Mon, Jan 10, 2005 at 11:27:02AM +0100, Philippe Guyot wrote: > > > On Thursday 06 January 2005 15:33, you wrote: > > > > On Thursday 06 January 2005 14:57, you wrote: > > > > > On Thu, Jan 06, 2005 at 12:19:46PM +0100, Philippe Guyot wrote: > > > > > > On Wednesday 05 January 2005 12:41, you wrote: > > > > > > > On Wed, Jan 05, 2005 at 10:31:35AM +0100, Philippe Guyot wrote: > > > > > > > > On Tuesday 04 January 2005 19:21, you wrote: > > > > > > > > > Ok, so you got a 43P-140 (Tiger1), good to know. > > > > > > > > > > > > > > > > > > > > > > > > > > > I only have trouble with device 0000:00:01.1, which is the > > > > > > > > > SL82C105 ide chip, but as i have no connector for those > > > > > > > > > anyway, it is not troublesomoe. > > > > > > > > > > > > > > > > I think this box hasn't a real ide device, as far as I can > > > > > > > > see. disks, cdrom,tape are on scsi. > > > > > > > > > > > > > > Ah, but then what are those other devices ? > > > > > > > > > > > > If this can help, output of lspci: > > > > > > > > > > PCI: Cannot allocate resource region 0 of device > > > > > > > > > > 0000:00:0b.0 > > > > > > > > > > > > 00:0b.0 ISA bridge: IBM Fire Coral (rev 03) > > > > > > > > > > > > > > > > PCI: Cannot allocate resource region 0 of device > > > > > > > > > > 0000:00:0c.0 > > > > > > > > > > > > 00:0c.0 Ethernet controller: Advanced Micro Devices [AMD] 79c970 > > > > > > [PCnet LANCE] (rev 16) > > > > > > > > > > > > > > > > PCI: Cannot allocate resource region 0 of device > > > > > > > > > > 0000:00:10.0 > > > > > > > > > > > > 00:10.0 SCSI storage controller: LSI Logic / Symbios Logic > > > > > > (formerly NCR) > > > > > > > > > > So these three are baddly mapped, at least > > > > > > > > > > > > > > > PCI: Cannot allocate resource region 1 of device > > > > > > > > > > 0000:00:12.0 PCI: Cannot allocate resource region 2 of > > > > > > > > > > device 0000:00:12.0 > > > > > > > > > > > > 53c825 (rev 13) > > > > > > 00:12.0 Communication controller: Synaptel: Unknown device 0111 > > > > > > (rev b1) > > > > > > > > > > No idea why there are two ressource regions here though. No idea > > > > > whay this synaptel part is anyway. > > > > > > > > This is an X25 communication card. > > > > It seems make no problem for woody when booting. > > > > I don't really have plans to use it, I may remove it from the box. > > > > > > So did I. > > > I tested again this morning, netbooting > > > /~luther/d-i/images/daily/powerpc/netboot/vmlinuz-prep.initrd (08 jan > > > 22:01). > > > > > > as previously, mapping problem it seems: > > > > > > PCI: Cannot allocate resource region 0 of device 0000:00:0b.0 > > > PCI: Cannot allocate resource region 0 of device 0000:00:0c.0 > > > PCI: Cannot allocate resource region 0 of device 0000:00:10.0 > > > > > > of course those errors disapear because of synaptel out of the box: > > > > > > > PCI: Cannot allocate resource region 1 of device 0000:00:12.0 > > > > > > > PCI: Cannot allocate resource region 2 of device 0000:00:12.0 > > > > As expected. > > > > > and the same final VFS problem: > > > > > > RAMDISK: Compressed image found at block 0 > > > VFS: Mounted root (cramfs filesystem) readonly. > > > VFS: Cannot open root device "<NULL>" or unknown-block(8,3) > > > Please append a correct "root=" boot option > > > Kernel panic: VFS: Unable to mount root fs on unknown-block(8,3) > > > <0>Rebooting in 180 seconds.. > > > > > > Just for testing purposes, if it could help a little > > > > > > linux/ppc load: console=ttyS0,9600 root=/dev/sda2 (woody) > > > VFS: Cannot open root device "sda2" > > > > What kernel was that again ? > > /~luther/d-i/images/daily/powerpc/netboot/vmlinuz-prep.initrd (08 jan > 22:01). > > > I think you have a serious pci irq mapping > > trouble, which need to be fixed. Could you investigate this with the prep > > knowledgeable guys on this list ? > > Will be happy to do that with the help of other persons > >
It seems to me there are two issues in that. 1) The pci irq mapping problem I have no infos more yet. 2) the "cannot open root device" problem for which it seems to exist a workaround: "load :console=ttyS0,9600 root=/dev/ram" Despite of these 2 subsequent messages: FATAL: module usbkbd not found FATAL: module hid not found the install goes on rather nicely, I stopped just before repartitionning the scsi disk. (do not want to kill my running woody just now ! I am not sure of consequences of pci problem). Because of workaround 2, I can't do the job with my graphic card (Matrox) unless I find something like console=vga..... Friendly, Felipe
