Im running Debian Linux for powerpc with Benh kernel 2.4.21
(installed pre-compiled for OW SCSI) on a Macintosh PowerPC
9600/300. I have some problems I would like to get some help with.
Heres the first problem: SCSI device dont show!
Output of lspci-vv shows that the system can see my SCSI card,
Adaptec AIC-7881U.
00:0d.0 SCSI storage controller: Adaptec AIC-7881U
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 2000ns max), cache line size 08
Interrupt: pin A routed to IRQ 23
Region 0: I/O ports at 1000 [size=256]
Region 1: Memory at 80800000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at 80810000 [disabled] [size=64K]
But if I look in /proc/scsi/ I see only the motherboard SCSI adapter.
Output of kernel boot log shows that the SCSI card is not found at all at boot:
Aug 17 12:14:53 demonbox kernel: SCSI subsystem driver Revision: 1.00
Aug 17 12:14:53 demonbox kernel: mesh: configured for synchronous 5 MB/s
Aug 17 12:14:53 demonbox kernel: mesh: performing initial bus reset...
Aug 17 12:14:53 demonbox kernel: scsi0 : MESH
Aug 17 12:14:53 demonbox kernel: mesh: target 0 synchronous at 5.0 MB/s
Aug 17 12:14:53 demonbox kernel: Vendor: IBM Model:
DCAS-34330 Rev: S65A
Aug 17 12:14:53 demonbox kernel: Type: Direct-Access
ANSI SCSI revision: 02
Aug 17 12:14:53 demonbox kernel: mesh: target 3 synchronous at 5.0 MB/s
Aug 17 12:14:53 demonbox kernel: Vendor: MATSHITA Model: CD-ROM
CR-8024 Rev: 2.0e
Aug 17 12:14:53 demonbox kernel: Type: CD-ROM
ANSI SCSI revision: 02
Aug 17 12:14:53 demonbox kernel: Vendor: IOMEGA Model: ZIP 100
Rev: E.08
Aug 17 12:14:53 demonbox kernel: Type: Direct-Access
ANSI SCSI revision: 02
Aug 17 12:14:53 demonbox kernel: scsi1 : 53C94
Aug 17 12:14:53 demonbox kernel: Attached scsi disk sda at scsi0,
channel 0, id 0, lun 0
Aug 17 12:14:53 demonbox kernel: Attached scsi removable disk sdb at
scsi0, channel 0, id 5, lun 0
Aug 17 12:14:53 demonbox kernel: SCSI device sda: 8467200 512-byte
hdwr sectors (4335 MB)
Aug 17 12:14:53 demonbox kernel: Partition check:
Aug 17 12:14:53 demonbox kernel: sda: [mac] sda1 sda2 sda3 sda4 sda5
sda6 sda7 sda8 sda9 sda10 sda11
Aug 17 12:14:53 demonbox kernel: Attached scsi CD-ROM sr0 at scsi0,
channel 0, id 3, lun 0
Aug 17 12:14:53 demonbox kernel: sr0: scsi-1 drive
Why is my card seen by lspci but not the kernel? And what is that
53C94 that I see at scsi1?
And this also gives that the IBM harddrive on the Adaptec card is not
found at all. Should I do something with the HD to get it recognized?
I can also add that the HD comes up in Mac OS 9 without problem.
With hope for help
/Svante
