Still struggling with getting the scsi-emulation working in order to use the cd-burner on my iBook2 14".
I've compiled scsi emulation into my kernel version: 2.4.20-rc1-ben0. I've added an ide-scsi file in /etc/modutils containing the line: alias scsi_hostadapter ide-scsi and run update-modules. I assume because I've compiled scsi emulation into the kernel that this isn't actually necessary. As mentioned in a previous thread on this topic, it's likely that the ide driver may have claimed the drive before ide-scsi. Can someone more knowledgable then me confirm this from my kernel output. It appears to me that this is the case. So how to I fix this? Memory BAT mapping: BAT2=256Mb, BAT3=0Mb, residual: 0Mb Total memory = 256MB; using 512kB for hash table (at c0400000) Linux version 2.4.20-rc1-ben0 ([EMAIL PROTECTED]) (gcc version 2.95.4 20011002 (Debian prerelease)) #1 Mon Nov 4 22:18:14 EST 2002 Found Uninorth memory controller & host bridge, revision: 192 Mapped at 0xfdf3c000 Found a Pangea mac-io controller, rev: 0, mapped at 0xfdebc000 Processor NAP mode on idle enabled. PowerMac motherboard: iBook 2 rev. 2 PMU driver 2 initialized for Core99, firmware: 0c CPU HID1 : 0x70000044 Found UniNorth PCI host bridge at 0xf0000000. Firmware bus number: 0->0 hose pci, pci_mem_offset: 00000000, start0: f1000000 io_base_virt: fd6b5000, io_base_phys: f0000000, isa_mem_base: 00000000 Found UniNorth PCI host bridge at 0xf2000000. Firmware bus number: 0->0 hose pci, pci_mem_offset: 00000000, start0: f3000000 io_base_virt: fceb3000, io_base_phys: f2000000, isa_mem_base: 00000000 Found UniNorth PCI host bridge at 0xf4000000. Firmware bus number: 0->0 hose pci, pci_mem_offset: 00000000, start0: f5000000 io_base_virt: fc6b1000, io_base_phys: f4000000, isa_mem_base: 00000000 On node 0 totalpages: 65536 zone(0): 65536 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: root=/dev/hda4 ro PowerMac using OpenPIC irq controller OpenPIC Version 1.2 (4 CPUs and 64 IRQ sources) at fc66d000 OpenPIC timer frequency is 4.160000 MHz GMT Delta read from XPRAM: -300 minutes, DST: off time_init: decrementer frequency = 24.835213 MHz Console: colour dummy device 80x25 Calibrating delay loop... 1389.36 BogoMIPS Memory: 254900k available (2256k kernel code, 1160k data, 176k init, 0k highmem) AGP special page: 0xcffff000 Dentry cache hash table entries: 32768 (order: 6, 262144 bytes) Inode cache hash table entries: 16384 (order: 5, 131072 bytes) Mount-cache hash table entries: 4096 (order: 3, 32768 bytes) Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes) Page-cache hash table entries: 65536 (order: 6, 262144 bytes) POSIX conformance testing by UNIFIX PCI: Probing PCI hardware Scanning bus 00 Found 00:58 [106b/0027] 000600 00 Found 00:80 [1002/4c59] 000300 00 Fixup res 1 (101) of dev 00:10.0: 400 -> 802400 Fixups for bus 00 Bus scan for 00 returning with max=00 Scanning bus 10 Found 10:58 [106b/0028] 000600 00 Found 10:b8 [106b/0025] 00ff00 00 Found 10:c0 [106b/0026] 000c03 00 Found 10:c8 [106b/0026] 000c03 00 Fixups for bus 10 Bus scan for 10 returning with max=10 Scanning bus 20 Found 20:58 [106b/0029] 000600 00 Found 20:70 [106b/0030] 000c00 00 Found 20:78 [106b/0024] 000200 00 Fixups for bus 20 Bus scan for 20 returning with max=20 PCI->OF bus map: 0 -> 0 16 -> 0 32 -> 0 PCI:00:10.0: Resource 0: 98000000-9fffffff (f=1208), vd: 1002, dev: 4c59 PCI:00:10.0: Resource 2: 90000000-9000ffff (f=200), vd: 1002, dev: 4c59 PCI:10:17.0: Resource 0: 80000000-8007ffff (f=200), vd: 106b, dev: 0025 PCI:20:0f.0: Resource 0: f5200000-f53fffff (f=200), vd: 106b, dev: 0024 PCI:00:10.0: Resource 1: 00802400-008024ff (f=101), vd: 1002, dev: 4c59 PCI:10:18.0: Resource 0: 80081000-80081fff (f=200), vd: 106b, dev: 0026 PCI:10:19.0: Resource 0: 80080000-80080fff (f=200), vd: 106b, dev: 0026 PCI:20:0e.0: Resource 0: f5000000-f5000fff (f=200), vd: 106b, dev: 0030 Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd Journalled Block Device driver loaded Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]). i2c-core.o: i2c core module i2c-dev.o: i2c /dev entries driver module i2c-core.o: driver i2c-dev dummy driver registered. i2c-proc.o version 2.6.1 (20010825) PCI: Enabling device 00:10.0 (0086 -> 0087) radeonfb: ref_clk=2700, ref_div=12, xclk=16615 from OF radeonfb: detected DFP panel size from EDID: 1024x768 Console: switching to colour frame buffer device 128x48 Registered "ati" backlight controller, level: 15/15 radeonfb: ATI Radeon M6 LY DDR SGRAM 16 MB radeonfb: DVI port LCD monitor connected radeonfb: CRT port no monitor connected no framebuffer address found for /[EMAIL PROTECTED]/ATY,[EMAIL PROTECTED]/ATY,Fall_B input0: Macintosh mouse button emulation pty: 256 Unix98 ptys configured Uniform Multi-Platform E-IDE driver Revision: 6.31 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ide0: Found Apple KeyLargo ATA-4 controller, bus ID 2 Probing IDE interface ide0... hda: IBM-IC25N030ATCS04-0, ATA DISK drive hdb: SONY CD-RW CRX800E, ATAPI CD/DVD-ROM drive ide0 at 0xd5214000-0xd5214007,0xd5214160 on irq 19 hda: Enabling Ultra DMA 2 blk: queue c0363ba0, I/O limit 4095Mb (mask 0xffffffff) hda: 58605120 sectors (30006 MB) w/1768KiB Cache, CHS=58140/16/63, UDMA(33) hdb: Enabling MultiWord DMA 2 hdb: ATAPI 24X DVD-ROM CD-R/RW drive, 8192kB Cache, DMA Uniform CD-ROM driver Revision: 3.12 ide-floppy driver 0.99.newide Partition check: hda: [mac] hda1 hda2 hda3 hda4 hda5 hda6 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) sungem.c:v0.97 3/20/02 David S. Miller (davem@redhat.com) eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:03:93:88:80:c6 eth0: Found BCM5221 PHY pcnet32.c:v1.27b 01.10.2002 [EMAIL PROTECTED] PPP generic driver version 2.4.2 PPP Deflate Compression module registered Linux agpgart interface v0.99 (c) Jeff Hartmann agpgart: Maximum main memory to use for agp memory: 204M agpgart: Detected Apple UniNorth/Pangea chipset agp: configuring for size idx: 4 agpgart: AGP aperture is 16M @ 0x0 ide-floppy driver 0.99.newide SCSI subsystem driver Revision: 1.00 mesh: configured for synchronous 5 MB/s kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2 kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2 kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2 kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2 kmod: failed to exec /sbin/modprobe -s -k i2c-keywest, errno = 2 tas driver [TAS3004 driver V 0.3]) using i2c address: 0x35 from device-tree i2c-core.o: driver TAS3004 driver V 0.3 registered. Audio jack unplugged, enabling speakers. AE-Init snapper mixer PowerMac Snapper DMA sound driver rev 016 installed Core driver edition 01.06 : PowerMac Built-in Sound driver edition 00.07 Write will use 4 fragments of 32768 bytes as default PowerMac Z8530 serial driver version 2.0 tty00 at 0xd22d7020 (irq = 22) is a Z8530 ESCC tty01 at 0xd22de000 (irq = 23) is a Z8530 ESCC Macintosh non-volatile memory driver v1.0 Thermal Infos found : implementation id : 3 fan_count : 1 thermostat_count : 2 ranges[0] : 0,0 ranges[1] : 0,4 ranges[2] : 192,55 ranges[3] : 243,40 thermostat: design id 3 unknown ! apm_emu: APM Emulation 0.5 initialized. usb.c: registered new driver usbdevfs usb.c: registered new driver hub PCI: Enabling device 10:18.0 (0000 -> 0002) PCI: Enabling bus mastering for device 10:18.0 usb-ohci.c: USB OHCI at membase 0xd22e4000, IRQ 27 usb-ohci.c: usb-10:18.0, Apple Computer Inc. KeyLargo/Pangea USB adb: starting probe task... usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected PCI: Enabling device 10:19.0 (0000 -> 0002) PCI: Enabling bus mastering for device 10:19.0 usb-ohci.c: USB OHCI at membase 0xd22e6000, IRQ 28 usb-ohci.c: usb-10:19.0, Apple Computer Inc. KeyLargo/Pangea USB (#2) usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 2 ports detected usb.c: registered new driver hiddev usb.c: registered new driver hid hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <[EMAIL PROTECTED]> hid-core.c: USB HID support drivers mice: PS/2 mouse device common for all mice i2c-dev.o: Registered 'uni-n 0' as minor 0 i2c-core.o: adapter uni-n 0 registered as adapter 0. i2c-dev.o: Registered 'uni-n 1' as minor 1 i2c-core.o: adapter uni-n 1 registered as adapter 1. Found KeyWest i2c on "uni-n", 2 channels, stepping: 4 bits i2c-dev.o: Registered 'mac-io 0' as minor 2 i2c-core.o: client [tas Digital Equalizer] registered to adapter [mac-io 0](pos. 0). i2c-core.o: adapter mac-io 0 registered as adapter 2. Found KeyWest i2c on "mac-io", 1 channel, stepping: 4 bits NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 2048 buckets, 16Kbytes TCP: Hash tables configured (established 16384 bind 16384) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. adb devices:<6>kjournald starting. Commit interval 5 seconds [2]: 2 c3<6>EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 176k init 8k chrp 8k prep [3]: 3 1 [7]: 7 1f ADB keyboard at 2, handler 1 Detected ADB keyboard, type ANSI. input1: ADB HID on ID 2:2.c3 input2: ADB HID on ID 7:7.1f ADB mouse at 3, handler set to 4 (trackpad) input3: ADB HID on ID 3:3.01 adb: finished probe task... Adding Swap: 262136k swap-space (priority -1) EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,4), internal journal hermes.c: 5 Apr 2002 David Gibson <[EMAIL PROTECTED]> orinoco.c 0.11b (David Gibson <[EMAIL PROTECTED]> and others) airport.c 0.11b (Benjamin Herrenschmidt <[EMAIL PROTECTED]>) eth1: Station identity 001f:0001:0008:000c eth1: Looks like a Lucent/Agere firmware version 8.12 eth1: Ad-hoc demo mode supported eth1: IEEE standard IBSS ad-hoc mode supported eth1: WEP supported, 104-bit key eth1: MAC address 00:30:65:17:A8:17 eth1: Station name "HERMES I" eth1: ready airport: card registered for interface eth1
