On Thu, Jul 11, 2002 at 12:09:26PM -0500, Kent West wrote:
> Kent West wrote:
> >The cp was successful, but the "ybin -v" produced the same errors.
It shouldn't have complained about the lack of a proc filesystem in the
normal installer environment.
>
> So I started the installation over, and this time, during partitioning,
> wiped the Apple Partition which gave me an empty drive, then created a
> bootstrap partition (with the "b" command), created a 256MB swap
> partition, and used the rest of the drive for a single / partition.
>
> When I got to the step to "Make System Bootable", I had the same
> failures: yabootconfig failed. When I tried to run "yabootconfig"
> manually on the second vt, it complained that it couldn't determine the
> root partition.
>
> I'm really thinking there's something screwy about this particular G3's
> hardware setup. I opened the case and took a look (didn't change
> anything). The Maxtor hard drive is the only device plugged into the IDE
> port on the mobo, and it's set to Master. The CDROM and zip drives are
> plugged into the Ultra ATA port on the mobo.
>
> I've been trying to figure out how the aliases work, and it's not making
> sense to me.
>
> According to "printenv", the "bootdevice" is set to "hd:,//:txbi", and
> according to "devalias", "hd" and "ultra0" both are set to
> "/pci/@d/[EMAIL PROTECTED]/[EMAIL PROTECTED]/[EMAIL PROTECTED]". BIG
> ASSUMPTION: I assumed that the
> command "mac-boot" is equivalent to "boot hd:,//:txbi", so I ran that
> command, and got the (by now, familiar) error "can't OPEN: hd:,//:txbi".
> I tried it also with "ultra0" instead of "hd", and with the long name
> (appropriately adapted).
>
> And since I've been able to boot the installation by referring to "ide0"
> instead of "hd", it seems to me that "hd" doesn't refer to the hard disk
Right. I think you just need to s/hd/ide0/ in all the documentation.
> at all. "devalias" refers to "cd" and "zip" and "ide0" as being on the
> same controller ("mac-io/[EMAIL PROTECTED]", with the cd adding "[EMAIL
> PROTECTED]" and
> the zip adding "[EMAIL PROTECTED]"). So "cd" is essentially the same as
> "ide0/[EMAIL PROTECTED]", but that can't be because when I boot the Debian
> installation using a reference to "ide0", the installation starts from
> the hard disk instead of the CDROM.
>
> So it seems to me that the aliases in OpenFirmware are messed up. I
> tried a "set-defaults" command (or something similar; I found it on the
> web yesterday but don't remember the exact command name), followed by a
> "reset-all", which rebooted the Mac, but nothing changed.
I believe your hardware is set up on a different scheme than normal, re:
ide master/slave/primary/secondary.
> Related, sort of: Does setting the "Startup Disk" in MacOS simply change
> the "boot-device" setting in OpenFirmware? In other words, could I
> simulate changing the Startup Disk in MacOS with a command similar to
> "setenv boot-device=[whatever makes CDROM vs Hard Drive, etc)?
I don't know, but I don't think so. It changes files on the hard drive
that the MacOS ROM reads at boot, I think.
--
*------v--------- Installing Debian GNU/Linux 3.0 --------v------*
| <http://www.debian.org/releases/woody/installmanual> |
| debian-imac (potato): <http://debian-imac.sourceforge.net> |
| Chris Tillman [EMAIL PROTECTED] |
| May the Source be with you |
*----------------------------------------------------------------*
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
