Hi all, over here we are using an MVME2604 CPU-board, running OS9, with a SCSI-disk. This is working allright. Now we want to find out whether Linux is working, so I downloaded bootfull.bin from Debian, the woody one, and it doesn't recognize the SCSI-disk Below is the output, generated by the boot-process.
Copyright Motorola Inc. 1988 - 1999, All Rights Reserved PPC1 Debugger/Diagnostics Release Version 4.3 - 01/20/99 RM01 COLD Start Local Memory Found =04000000 (&67108864) MPU Clock Speed =333Mhz BUS Clock Speed =67Mhz WARNING: Keyboard Not Connected Reset Vector Location : ROM Bank B Mezzanine Configuration: Single-MPU Current 60X-Bus Master : MPU0 Idle MPU(s) : NONE System Memory: 64MB, ECC Enabled (ECC-Memory Detected) L2Cache: 256KB SelfTest/Boots about to Begin... Press <BREAK> at anytime to Abort ALL NetBoot about to Begin... Press <ESC> to Bypass, <SPC> to Continue Network Booting from: DEC21140, Controller 0, Device 0 Device Name: /[EMAIL PROTECTED]/pci1011,[EMAIL PROTECTED],0:0,0 Loading: bootfull.bin Client IP Address = 192.168.8.241 Server IP Address = 192.168.8.172 Gateway IP Address = 192.168.8.1 Subnet IP Address Mask = 255.255.255.0 Boot File Name = bootfull.bin Argument File Name = Network Boot File load in progress... To abort hit <BREAK> Bytes Received =&2245162, Bytes Loaded =&2245162 Bytes/Second =&140322, Elapsed Time =16 Second(s) loaded at: 001F0400 00207220 relocated to: 00800000 00816E20 board data at: 00810314 00816D20 relocated to: 00810314 00816D20 zimage at: 001FB400 002ACC57 relocated to: 00817000 008C8857 initrd at: 002ACC57 0041244D relocated to: 008C9000 00A2E7F6 avail ram: 00400000 00800000 Linux/PPC load: root=/dev/ram ip=off Uncompressing Linux...done. Now booting the kernel PReP architecture Total memory = 32MB; using 128kB for hash table (at c01e0000) Linux version 2.2.20PREP ([EMAIL PROTECTED]) (gcc version 2.95.4 20011002 (Debian prerelease)) #1 Thu May 16 10:55:55 EDT 2002 Boot arguments: root=/dev/ram ip=off time_init: decrementer frequency = 1000013880/60 (15MHz) Calibrating delay loop... 222.00 BogoMIPS Memory: 29020k available (1188k kernel code, 1000k data, 128k init) [c0000000,c2000000] Dentry hash table entries: 4096 (order 3, 32k) Buffer cache hash table entries: 32768 (order 5, 128k) Page cache hash table entries: 8192 (order 3, 32k) POSIX conformance testing by UNIFIX PCI: Probing PCI hardware Setting PCI interrupts for a "MVME 2600/2700 with MVME761" Linux NET4.0 for Linux 2.2 Based upon Swansea University Computer Society NET3.039 NET4: Unix domain sockets 1.0 for Linux NET4.0. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP TCP: Hash tables configured (ehash 32768 bhash 32768) Starting kswapd v 1.5 initialize_kbd: Keyboard reset failed, no ACK Detected PS/2 Mouse Port. Serial driver version 4.27 with<4>keyboard: Timeout - AT keyboard not present? keyboard: Timeout - AT keyboard not present? MANY_PORTS enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A ttyS01 at 0x02f8 (irq = 3) is a 16550A pty: 256 Unix98 ptys configured RAM disk driver initialized: 16 RAM disks of 4096K size loop: registered device at major 7 Floppy drive(s): fd0 is 2.88M FDC 0 is a National Semiconductor PC87306 scsi : 0 hosts. scsi : detected total. 3c59x.c 18Feb01 Donald Becker and others http://www.scyld.com/network/vortex.html pcnet32.c: PCI bios is present, checking for devices... RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem). Freeing unused kernel memory: 128k init 4k pmac 4k open firmware serial console detected. Disabling virtual terminals. init started: BusyBox v0.60.3-pre (2002.01.19-22:40+0000) multi-call binary ------------ Here is a part of the output from OS9, concerning the harddisk: OS-9 Bootstrap for the PowerPC(tm) (Edition 64) Now trying to Scan SCSI devices. Symbios 53C825 @ 0x8ffffe00 SELFID (07) MAXCNT (0x01000000) ID Vendor Product Rev Block Size Total Blks Disk Size ------------------------------------------------------------------------ 0x00 QUANTUM LPS270S 5900 0x00000200 0x000811a7 270749696 Does anybody have a clue why Linux doesn't recognize my harddisk? Thanks in advance. A.T.J. van den Broek Software engineer Leica Microsystems Lithography Technical Support Center Bedrijfsweg 22-24 5683 CP Best, the Netherlands Tel: +31 499 336882 Fax: +31 499 336899 -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
