This is additional info. I am now running kernel 2.4.2-pre1, still on the Lombard, and this is the result of "lspci -vv":
In the same thread, I posted the log and the config files. Sergio --> lspci -vv 00:00.0 Host bridge: Motorola MPC106 [Grackle] (rev 40) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 0, cache line size 08 00:0e.0 USB Controller: Lucent Microelectronics: Unknown device 5801 (rev 12) (prog-if 10 [OHCI]) Subsystem: Lucent Microelectronics: Unknown device 5801 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (750ns min, 21500ns max) Interrupt: pin A routed to IRQ 28 Region 0: Memory at 80882000 (32-bit, non-prefetchable) [size=4K] 00:0f.0 Multimedia controller: C-Cube Microsystems Cinemaster C 3.0 DVD Decoder (rev 02) Subsystem: C-Cube Microsystems Cinemaster C 3.0 DVD Decoder Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (1000ns min, 32000ns max) Interrupt: pin A routed to IRQ 26 Region 0: I/O ports at 0c00 [size=256] Capabilities: [60] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:10.0 Class ff00: Apple Computer Inc. Paddington Mac I/O Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Region 0: Memory at 80800000 (32-bit, non-prefetchable) [size=512K] 00:11.0 VGA compatible controller: ATI Technologies Inc 3D Rage LT Pro (rev dc) (prog-if 00 [VGA]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (2000ns min), cache line size 08 Interrupt: pin A routed to IRQ 24 Region 0: Memory at 81000000 (32-bit, non-prefetchable) [size=16M] Region 1: I/O ports at <unassigned> [size=256] Region 2: Memory at 80881000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at <unassigned> [disabled] [size=128K] Capabilities: [5c] Power Management version 1 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:13.0 CardBus bridge: Texas Instruments PCI1211 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 22 Region 0: Memory at 80880000 (32-bit, non-prefetchable) [disabled] [size=4K] Bus: primary=00, secondary=01, subordinate=04, sec-latency=0 I/O window 0: 00000000-00000003 [disabled] I/O window 1: 00000000-00000003 [disabled] BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt- PostWrite- 16-bit legacy interface ports at 1001