-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1
Benjamin Herrenschmidt wrote:
| Not sure,can you enable radeonfb verbose debug and send me the output of | dmesg ?
Done. Here is the dmesg
by, Martin
- --
Powered by Debian GNU / Linux -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.2.5 (GNU/Linux) Comment: Using GnuPG with Thunderbird - http://enigmail.mozdev.org
iD8DBQFCEyfWGxxhbGlQyAkRAqH2AJ94ION2RmKA+S1DRr9nERCFr57QdwCdET+Z ctInLfYWG2SrZioA0k2P2Wk= =kavx -----END PGP SIGNATURE-----
Total memory = 384MB; using 1024kB for hash table (at c0400000) Linux version 2.6.11-rc4 ([EMAIL PROTECTED]) (gcc version 3.3.5 (Debian 1:3.3.5-8)) #1 Wed Feb 16 11:22:36 CET 2005 Found UniNorth memory controller & host bridge, revision: 210 Mapped at 0xfdfc0000 Found a Intrepid mac-io controller, rev: 0, mapped at 0xfdf40000 Processor NAP mode on idle enabled. PowerMac motherboard: iBook G4 Found UniNorth PCI host bridge at 0xf0000000. Firmware bus number: 0->0 Found UniNorth PCI host bridge at 0xf2000000. Firmware bus number: 0->0 Found UniNorth PCI host bridge at 0xf4000000. Firmware bus number: 0->0 via-pmu: Server Mode is disabled PMU driver 2 initialized for Core99, firmware: 0c nvram: Checking bank 0... nvram: gen0=334, gen1=333 nvram: Active bank is: 0 nvram: OF partition at 0x410 nvram: XP partition at 0x1020 nvram: NR partition at 0x1120 On node 0 totalpages: 98304 DMA zone: 98304 pages, LIFO batch:16 Normal zone: 0 pages, LIFO batch:1 HighMem zone: 0 pages, LIFO batch:1 Built 1 zonelists Kernel command line: root=/dev/hda6 ro ethernet=offline video=radeonfb:1024x786-32 PowerMac using OpenPIC irq controller at 0x80040000 OpenPIC Version 1.2 (4 CPUs and 64 IRQ sources) at fc6ef000 OpenPIC timer frequency is 4.166666 MHz PID hash table entries: 2048 (order: 11, 32768 bytes) GMT Delta read from XPRAM: 0 minutes, DST: off time_init: decrementer frequency = 18.432000 MHz Console: colour dummy device 80x25 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 384384k available (2544k kernel code, 1220k data, 168k init, 0k highmem) AGP special page: 0xd7fff000 Calibrating delay loop... 610.30 BogoMIPS (lpj=305152) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) NET: Registered protocol family 16 PCI: Probing PCI hardware PCI: Cannot allocate resource region 0 of device 0001:10:18.0 PCI: Cannot allocate resource region 0 of device 0001:10:19.0 Apple USB OHCI 0001:10:18.0 disabled by firmware Apple USB OHCI 0001:10:19.0 disabled by firmware Registering openpic with sysfs... usbcore: registered new driver usbfs usbcore: registered new driver hub Thermal assist unit not available Registering PowerMac CPU frequency driver Low: 606 Mhz, High: 798 Mhz, Boot: 606 Mhz SGI XFS with no debug enabled SGI XFS Quota Management subsystem Initializing Cryptographic API radeonfb_pci_register BEGIN PCI: Enabling device 0000:00:10.0 (0006 -> 0007) aper_base: 98000000 MC_FB_LOC to: 9bff9800, MC_AGP_LOC to: ffffa000 radeonfb (0000:00:10.0): Found 32768k of DDR 64 bits wide videoram radeonfb (0000:00:10.0): mapped 16384k videoram radeonfb (0000:00:10.0): Invalid ROM signature 0 should be0xaa55 radeonfb: Retreived PLL infos from Open Firmware radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=190.00 Mhz, System=183.00 MHz radeonfb: PLL min 12000 max 35000 Starting monitor auto detection... radeonfb: I2C (port 1) ... not found radeonfb: I2C (port 2) ... found LVDS panel radeonfb: I2C (port 3) ... not found radeonfb: I2C (port 4) ... not found radeon_probe_OF_head head: ATY,Via_A (letter: A, head_no: 0) analyzing OF properties... display-type: LCD radeon_probe_OF_head head: ATY,Via_A (letter: A, head_no: 1) radeonfb: I2C (port 3) ... not found radeonfb: I2C (port 4) ... not found radeonfb: Monitor 1 type LCD found radeonfb: EDID probed radeonfb: Monitor 2 type no found Parsing EDID data for panel info radeonfb: Using Firmware dividers 0x000600ad from PPLL 0 Setting up default mode based on panel info radeonfb: Dynamic Clock Power Management enabled hStart = 664, hEnd = 800, hTotal = 960 vStart = 403, vEnd = 409, vTotal = 438 h_total_disp = 0x4f0077 hsync_strt_wid = 0x910292 v_total_disp = 0x18f01b5 vsync_strt_wid = 0x860192 pixclock = 15384 freq = 6500 Console: switching to colour frame buffer device 80x25 Registered "mnca" backlight controller, level: 15/15 radeonfb (0000:00:10.0): ATI Radeon \c radeonfb_pci_register END Macintosh non-volatile memory driver v1.1 Linux agpgart interface v0.100 (c) Dave Jones agpgart: Detected Apple UniNorth 2 chipset agpgart: Maximum main memory to use for agp memory: 322M agpgart: configuring for size idx: 4 agpgart: AGP aperture is 16M @ 0x0 [drm] Initialized drm 1.0.0 20040925 io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize sungem.c:v0.98 8/24/03 David S. Miller (davem@redhat.com) eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:0a:95:ac:20:be PHY ID: 4061e4, addr: 0 eth0: Found BCM5221 PHY MacIO PCI driver attached to Intrepid chipset input: Macintosh mouse button emulation apm_emu: APM Emulation 0.5 initialized. Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx adb: starting probe task... PCI: Enabling device 0002:20:0d.0 (0000 -> 0002) adb devices: [2]: 2 c4 [3]: 3 1 [7]: 7 1f ADB keyboard at 2, handler 1 Detected ADB keyboard, type ISO, swapping keys. input: ADB keyboard on adb2:2.c4/input input: ADB Powerbook buttons on adb7:7.1f/input ADB mouse at 3, handler set to 4 (trackpad) input: ADB mouse on adb3:3.01/input adb: finished probe task... ide0: Found Apple UniNorth ATA-6 controller, bus ID 3, irq 39 Probing IDE interface ide0... hda: TOSHIBA MK3021GAS, ATA DISK drive hda: Enabling Ultra DMA 5 ide0 at 0xd9022000-0xd9022007,0xd9022160 on irq 39 ide1: Found Apple KeyLargo ATA-3 controller, bus ID 0, irq 24 Probing IDE interface ide1... hdc: MATSHITACD-RW CW-8123, ATAPI CD/DVD-ROM drive hdc: Enabling MultiWord DMA 2 ide1 at 0xd900e000-0xd900e007,0xd900e160 on irq 24 hda: max request size: 128KiB hda: 58605120 sectors (30005 MB), CHS=58140/16/63, UDMA(100) hda: cache flushes supported hda: [mac] hda1 hda2 hda3 hda4 hda5 hda6 hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, (U)DMA Uniform CD-ROM driver Revision: 3.20 mice: PS/2 mouse device common for all mice Found KeyWest i2c on "uni-n", 2 channels, stepping: 4 bits Found KeyWest i2c on "mac-io", 1 channel, stepping: 4 bits tas driver [TAS3004 driver V 0.3]) using i2c address: 0x35 from device-tree Audio jack unplugged, enabling speakers. AE-Init snapper mixer PowerMac Snapper DMA sound driver rev 016 installed Core driver edition 01.06 : PowerMac Built-in Sound driver edition 00.07 Write will use 4 fragments of 32768 bytes as default Read will use 4 fragments of 32768 bytes as default Advanced Linux Sound Architecture Driver Version 1.0.8 (Thu Jan 13 09:39:32 2005 UTC). pmac: can't request resource 0! ALSA device list: No soundcards found. NET: Registered protocol family 2 IP: routing cache hash table of 4096 buckets, 32Kbytes TCP established hash table entries: 16384 (order: 5, 131072 bytes) TCP bind hash table entries: 16384 (order: 4, 65536 bytes) TCP: Hash tables configured (established 16384 bind 16384) NET: Registered protocol family 1 NET: Registered protocol family 17 XFS mounting filesystem hda6 Ending clean XFS mount for filesystem: hda6 VFS: Mounted root (xfs filesystem) readonly. Freeing unused kernel memory: 168k init 4k chrp 32k prep Adding 438692k swap on /var/swap/swapfile. Priority:-1 extents:2 ieee1394: Initialized config rom entry `ip1394' ohci1394: $Rev: 1223 $ Ben Collins <[EMAIL PROTECTED]> PCI: Enabling device 0002:20:0e.0 (0000 -> 0002) ohci1394: fw-host0: Unexpected PCI resource length of 1000! ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[40] MMIO=[f5000000-f50007ff] Max Packet=[2048] ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) Apple USB OHCI 0001:10:18.0 disabled by firmware Apple USB OHCI 0001:10:19.0 disabled by firmware PCI: Enabling device 0001:10:1a.0 (0000 -> 0002) ohci_hcd 0001:10:1a.0: Apple Computer Inc. KeyLargo/Intrepid USB (#3) ohci_hcd 0001:10:1a.0: irq 29, pci mem 0x80083000 ohci_hcd 0001:10:1a.0: new USB bus registered, assigned bus number 1 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected PCI: Enabling device 0001:10:1b.0 (0000 -> 0002) ohci_hcd 0001:10:1b.0: NEC Corporation USB ohci_hcd 0001:10:1b.0: irq 63, pci mem 0x80082000 ohci_hcd 0001:10:1b.0: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 3 ports detected PCI: Enabling device 0001:10:1b.1 (0000 -> 0002) ohci_hcd 0001:10:1b.1: NEC Corporation USB (#2) ohci_hcd 0001:10:1b.1: irq 63, pci mem 0x80081000 ohci_hcd 0001:10:1b.1: new USB bus registered, assigned bus number 3 ieee1394: Host added: ID:BUS[0-00:1023] GUID[000a95fffeac20be] hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected PCI: Enabling device 0001:10:1b.2 (0004 -> 0006) ehci_hcd 0001:10:1b.2: NEC Corporation USB 2.0 ehci_hcd 0001:10:1b.2: irq 63, pci mem 0x80080000 ehci_hcd 0001:10:1b.2: new USB bus registered, assigned bus number 4 ehci_hcd 0001:10:1b.2: park 0 ehci_hcd 0001:10:1b.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004 hub 4-0:1.0: USB hub found hub 4-0:1.0: 5 ports detected hStart = 1048, hEnd = 1184, hTotal = 1344 vStart = 771, vEnd = 777, vTotal = 806 h_total_disp = 0x7f00a7 hsync_strt_wid = 0x910415 v_total_disp = 0x2ff0325 vsync_strt_wid = 0x860302 pixclock = 15384 freq = 6500 [drm] Initialized radeon 1.14.0 20050125 on minor 0: ATI Technologies Inc RV250 5c63 [Radeon Mobility 9200 M9+] agpgart: Putting AGP V2 device at 0000:00:0b.0 into 4x mode agpgart: Putting AGP V2 device at 0000:00:10.0 into 4x mode [drm] Loading R200 Microcode usb 2-1: new full speed USB device using ohci_hcd and address 2 prism2usb_init: prism2_usb.o: 0.2.1-pre26 Loaded prism2usb_init: dev_info is: prism2_usb usbcore: registered new driver prism2_usb Writing 4096 bytes to ram @0x7e2ffe Writing 4096 bytes to ram @0x7e3ffe Writing 4096 bytes to ram @0x7e4ffe Writing 4096 bytes to ram @0x7e5ffe Writing 4096 bytes to ram @0x7e6ffe Writing 4096 bytes to ram @0x7e7ffe Writing 4096 bytes to ram @0x7e8ffe Writing 4096 bytes to ram @0x7e9ffe Writing 4096 bytes to ram @0x7eaffe Writing 4096 bytes to ram @0x7ebffe Writing 4096 bytes to ram @0x7ecffe Writing 4096 bytes to ram @0x7edffe Writing 3010 bytes to ram @0x7eeffe Writing 416 bytes to ram @0x7efc20 Writing 16 bytes to ram @0x7efdd0 Writing 4044 bytes to ram @0x7f0800 Writing 3288 bytes to ram @0x7fe000 ident: nic h/w: id=0x8026 1.0.0 ident: pri f/w: id=0x15 1.1.3 ident: sta f/w: id=0x1f 1.8.3 MFI:SUP:role=0x00:id=0x01:var=0x01:b/t=1/1 CFI:SUP:role=0x00:id=0x02:var=0x02:b/t=1/1 PRI:SUP:role=0x00:id=0x03:var=0x01:b/t=1/4 STA:SUP:role=0x00:id=0x04:var=0x01:b/t=1/15 PRI-CFI:ACT:role=0x01:id=0x02:var=0x02:b/t=1/1 STA-CFI:ACT:role=0x01:id=0x02:var=0x02:b/t=1/1 STA-MFI:ACT:role=0x01:id=0x01:var=0x01:b/t=1/1 Prism2 card SN: 000000000000 linkstatus=CONNECTED hStart = 664, hEnd = 800, hTotal = 960 vStart = 403, vEnd = 409, vTotal = 438 h_total_disp = 0x4f0077 hsync_strt_wid = 0x910292 v_total_disp = 0x18f01b5 vsync_strt_wid = 0x860192 pixclock = 15384 freq = 6500 hStart = 1048, hEnd = 1184, hTotal = 1344 vStart = 771, vEnd = 777, vTotal = 806 h_total_disp = 0x7f00a7 hsync_strt_wid = 0x910415 v_total_disp = 0x2ff0325 vsync_strt_wid = 0x860302 pixclock = 15384 freq = 6500 agpgart: Putting AGP V2 device at 0000:00:0b.0 into 4x mode agpgart: Putting AGP V2 device at 0000:00:10.0 into 4x mode [drm] Loading R200 Microcode hStart = 664, hEnd = 800, hTotal = 960 vStart = 403, vEnd = 409, vTotal = 438 h_total_disp = 0x4f0077 hsync_strt_wid = 0x910292 v_total_disp = 0x18f01b5 vsync_strt_wid = 0x860192 pixclock = 15384 freq = 6500 hStart = 664, hEnd = 800, hTotal = 960 vStart = 403, vEnd = 409, vTotal = 438 h_total_disp = 0x4f0077 hsync_strt_wid = 0x910292 v_total_disp = 0x18f01b5 vsync_strt_wid = 0x860192 pixclock = 15384 freq = 6500 hStart = 1048, hEnd = 1184, hTotal = 1344 vStart = 771, vEnd = 777, vTotal = 806 h_total_disp = 0x7f00a7 hsync_strt_wid = 0x910415 v_total_disp = 0x2ff0325 vsync_strt_wid = 0x860302 pixclock = 15384 freq = 6500 agpgart: Putting AGP V2 device at 0000:00:0b.0 into 2x mode agpgart: Putting AGP V2 device at 0000:00:10.0 into 2x mode [drm] Loading R200 Microcode
