Hello.
I'm using Debian on my laptop (Roverbook Navigator B510).
But there is problem with sound card and network card.
Sound: Ali 5451
Network: RealTek 8139
If I turn on in kernel config sound (Trident..., Ali5415..) and network
(Realtek 8139) drivers then after reboot network does not work.
I see mesages like this:
NETDEV WATCHDOG: eth0: transmit timed out
eth0: link up, 100Mbps, full-duplex, lpa 0xFFFF
syslog contains messages:
<skip>
Trident 4DWave/SiS 7018/ALi 5451,Tvia CyberPro 5050 PCI Audio, version
0.14.10h, 21:53:50 Dec 11 2003
PCI: Found IRQ 5 for device 00:04.0
trident: ALi Audio Accelerator found at IO 0x8800, IRQ 5
ac97_codec: AC97 Modem codec, id: CXT41 (Unknown)
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
PCI: Assigned IRQ 10 for device 00:0a.0
yenta 00:0a.0: Preassigned resource 0 busy, reconfiguring...
yenta 00:0a.0: Preassigned resource 1 busy, reconfiguring...
yenta 00:0a.0: Preassigned resource 2 busy, reconfiguring...
yenta 00:0a.0: Preassigned resource 3 busy, reconfiguring...
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
Yenta IRQ list 0000, PCI irq10
Socket status: ffffffff
PCI: Found IRQ 10 for device 00:02.0
host/usb-ohci.c: USB OHCI at membase 0xce82d000, IRQ 10
host/usb-ohci.c: usb-00:02.0, PCI device 10b9:5237
usb.c: new USB bus registered, assigned bus number 1
usb.c: kmalloc IF cde91a40, numif 1
usb.c: new device strings: Mfr=0, Product=2, SerialNumber=1
usb.c: USB device number 1 default language ID 0x0
Product: USB OHCI Root Hub
SerialNumber: ce82d000
<skip>
eth0: link up, 100Mbps, full-duplex, lpa 0xFFFF
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Tx queue start entry 4 dirty entry 0.
eth0: Tx descriptor 0 is ffffffff. (queue head)
eth0: Tx descriptor 1 is ffffffff.
eth0: Tx descriptor 2 is ffffffff.
eth0: Tx descriptor 3 is ffffffff.
eth0: link up, 100Mbps, full-duplex, lpa 0xFFFF
<skip>
Without sound driver network works fine.
lspci --vv :
00:00.0 Host bridge: ATI Technologies Inc: Unknown device cab2 (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at f4000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at f0400000 (32-bit, prefetchable) [size=4K]
Capabilities: [a0] AGP version 2.0
Status: RQ=15 SBA+ 64bit- FW+ Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
00:01.0 PCI bridge: ATI Technologies Inc: Unknown device 7010 (prog-if 00
[Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 99
Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: f0100000-f01fffff
Prefetchable memory behind bridge: f8000000-fbffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:02.0 USB Controller: Acer Laboratories Inc. [ALi] M5237 USB (rev 03)
(prog-if 10 [OHCI])
Subsystem: QUANTA Computer Inc: Unknown device 0705
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f0004000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:03.0 Modem: Acer Laboratories Inc. [ALi]: Unknown device 5457 (prog-if 00
[Generic])
Subsystem: QUANTA Computer Inc: Unknown device 0705
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 5
Region 0: Memory at f0005000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 8400 [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.0 Multimedia audio controller: Acer Laboratories Inc. [ALi] M5451 PCI
South Bridge Audio (rev 02)
Subsystem: QUANTA Computer Inc: Unknown device 0705
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR+ <PERR+
Latency: 64 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at 8800 [size=256]
Region 1: Memory at f0006000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:06.0 Bridge: Acer Laboratories Inc. [ALi] M7101 PMU
Subsystem: QUANTA Computer Inc: Unknown device 0705
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00:07.0 ISA bridge: Acer Laboratories Inc. [ALi] M1533 PCI to ISA Bridge
[Aladdin IV]
Subsystem: Acer Laboratories Inc. [ALi] ALI M1533 Aladdin IV ISA
Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [a0] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.0 CardBus bridge: ENE Technology Inc: Unknown device 1411 (rev 01)
Subsystem: QUANTA Computer Inc: Unknown device 0705
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 20
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+
PostWrite+
16-bit legacy interface ports at 0001
00:0c.0 FireWire (IEEE 1394): Texas Instruments: Unknown device 8026
(prog-if 10 [OHCI])
Subsystem: QUANTA Computer Inc: Unknown device 0705
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f0007000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at f0000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139 (rev
10)
Subsystem: QUANTA Computer Inc: Unknown device 0705
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 8c00 [size=256]
Region 1: Memory at f0007800 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.0 IDE interface: Acer Laboratories Inc. [ALi] M5229 IDE (rev c4)
(prog-if fa)
Subsystem: QUANTA Computer Inc: Unknown device 0705
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (500ns min, 1000ns max)
Interrupt: pin A routed to IRQ 0
Region 4: I/O ports at 9020 [size=16]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:05.0 VGA compatible controller: ATI Technologies Inc: Unknown device 4337
(prog-if 00 [VGA])
Subsystem: QUANTA Computer Inc: Unknown device 0705
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B+
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Region 1: I/O ports at a000 [size=256]
Region 2: Memory at f0100000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Status: RQ=47 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA+ AGP- 64bit- FW- Rate=<none>
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
What I need to do to setup sound and network driver correctly?
Andrei Stankevich (Moscow, Russia)
P.S. I red this mailing list but not found answer :(
