Re: pcmcia help?

Tue, 15 Oct 2002 20:03:34 -0500 

What does lsmod report?

My networking stuff looks like this for 2.2.x kernel.
[EMAIL PROTECTED]:~/app$ lsmod
Module                  Size  Used by
serial_cs               4980   0 (unused)
tulip_cb               30104   2
cb_enabler              2296   2 [tulip_cb]
ds                      6028   2 [serial_cs cb_enabler]
i82365                 21072   2
pcmcia_core            42384   0 [serial_cs cb_enabler ds i82365]
If yours is not similar then you should run modconf as root and select some modules. Use the pcnet_cs as suggested by Bruce instead of tulip_cb as in my situation. The serial_cs is for my modem card I believe. 

Hope this helps,
Eric
p.s. unload any modules that you don't need when running modconf if the drivers won't load. 



Andreas Goesele wrote:


Hi,

I already lost much too much time trying to get PCMCIA work on my
laptop (Samsung MV7000, potato, kernel 2.2.19, corega FEther
PCC-TXF). The card works under Win98.

When I put in the card, I get one deep beep, removing it one high
beep. The card is recognized and the modules seem to be loaded
alright. But ifconfig doesn't show eth0 and consequently a ping
results in "network is unreachable". The network information
(ip-address, network, netmask, gateway, broadcast) in network.conf is
most certainly correct. (But see below under 6.)

Trying to run the network script by hand invariably gives:

/etc/pcmcia/network start eth0

usage: /etc/pcmcia/network [action] [device name]
  actions: start check stop suspend resume

As I have exhausted all my possibility (re-reading various times the
PCMCIA-HOWTO, playing around with various settings ...) I would be
very grateful for some help!

Follows all the info I could get. (1. system log, 2. cardctl status,
3. cardctl config, 4. cardctl ident, 5. test_setup, 6. test_network,
7. dump_pirq

1) In the system log I have:

Oct 13 19:49:43 debi kernel: Linux PCMCIA Card Services 3.1.22
Oct 13 19:49:43 debi kernel:   kernel build: 2.2.19 #1 Wed Mar 20 19:41:41 EST 
2002
Oct 13 19:49:43 debi kernel:   options:  [pci] [cardbus] [apm]
Oct 13 19:49:43 debi kernel: PCI routing table version 1.0 at 0xfdf60
Oct 13 19:49:43 debi kernel:   00:08.1 -> irq 5
Oct 13 19:49:43 debi kernel: Intel PCIC probe:
Oct 13 19:49:43 debi kernel:   Ricoh RL5C478 rev 80 PCI-to-CardBus at slot 
00:08, mem 0x68000000
Oct 13 19:49:43 debi kernel:     host opts [0]: [serial irq] [io 3/6/1] [mem 
3/6/1] [pci irq 11] [lat 168/176] [bus 32/34]
Oct 13 19:49:43 debi kernel:     host opts [1]: [serial irq] [io 3/6/1] [mem 
3/6/1] [pci irq 5] [lat 168/176] [bus 35/37]
Oct 13 19:49:43 debi kernel:     ISA irqs (default) = 3,4,7,9,10,12,15 PCI 
status changes
Oct 13 19:49:44 debi kernel: cs: IO port probe 0x0c00-0x0cff: excluding 
0xcf8-0xcff
Oct 13 19:49:44 debi kernel: cs: IO port probe 0x0800-0x08ff: clean.
Oct 13 19:49:44 debi kernel: cs: IO port probe 0x0100-0x04ff: excluding 
0x378-0x37f 0x398-0x39f 0x4d0-0x4d7
Oct 13 19:49:44 debi kernel: cs: IO port probe 0x0a00-0x0aff: clean.
Oct 13 19:49:44 debi kernel: cs: memory probe 0xa0000000-0xa0ffffff: clean.

According to the PCMCIA Howto the 10th line should continue and look
as for instance: 
Could that be relevant?

2) Output of cardctl status:

Socket 0:
  5V 16-bit PC Card
  function 0: [ready], [wp]
Socket 1:
  no card
3) Output of cardctl config: Socket 0: 
  Vcc 5.0V  Vpp1 5.0V  Vpp2 5.0V
Socket 1:
  not configured

4) Output of cardctl ident:

Socket 0:
  product info: "corega", "FEther PCC-TXF"
  manfid: 0xc00f, 0x0000
  function: 6 (network)
Socket 1:
  no product info available

5) Output of test_setup:

Current kernel: 2.2.19 #1 Wed Mar 20 19:41:41 EST 2002
Module info from /lib/modules/2.2.19/pcmcia/pcmcia_core.o:
  Linux PCMCIA Card Services 3.1.22
  options: [pci] [cardbus] [apm]

Startup options from /etc/pcmcia.conf:
  PCMCIA=yes
  PCIC=i82365
  PCIC_OPTS=
  CORE_OPTS=
  CARDMGR_OPTS=

Checking current syslog files in /var/log:
  All PCMCIA messages are in /var/log/syslog.

Module status:
  The PCMCIA kernel modules are loaded correctly.

Daemon status:
  cardmgr is running (process 168)

Current socket status from /var/lib/pcmcia/stab:
  Socket 0: empty
  Socket 1: empty

6) Output of test_network:

PCMCIA network settings are coming from /etc/pcmcia/network.opts.
No PCMCIA network interfaces are configured.

There is a network device in socket 0:
  empty

7) Output of dump_pirq:

Interrupt routing table found at address 0xfdf60:
  Version 1.0, size 0x0080
  Interrupt router is device 00:07.0
  PCI exclusive interrupt mask: 0x0000 []
  Compatible router: vendor 0x8086 device 0x122e

Device 00:07.0 (slot 0): ISA bridge
  INTD: link 0x63, irq mask 0x0800 [11]

Device 00:08.0 (slot 0): CardBus bridge
  INTA: link 0x60, irq mask 0x0800 [11]
  INTB: link 0x61, irq mask 0x0020 [5]

Device 00:0b.0 (slot 0): VGA compatible controller
  INTA: link 0x62, irq mask 0x0400 [10]
Device 00:09.0 (slot 0): INTA: link 0x60, irq mask 0x0800 [11]
Device 00:0a.0 (slot 0): INTA: link 0x61, irq mask 0x0020 [5] 

Device 00:00.0 (slot 0): Host bridge
  INTA: link 0x60, irq mask 0xdef8 [3,4,5,6,7,9,10,11,12,14,15]
  INTB: link 0x61, irq mask 0x0020 [5]
  INTC: link 0x62, irq mask 0xdef8 [3,4,5,6,7,9,10,11,12,14,15]
  INTD: link 0x63, irq mask 0xdef8 [3,4,5,6,7,9,10,11,12,14,15]

Interrupt router at 00:07.0: Intel 82443MX PCI-to-ISA bridge
  PIRQ1 (link 0x60): irq 11
  PIRQ2 (link 0x61): irq 5
  PIRQ3 (link 0x62): unrouted
  PIRQ4 (link 0x63): irq 11
  Serial IRQ: [enabled] [continuous] [frame=21] [pulse=4]
  Level mask: 0x0820 [5,11]

Reply via email to