Monday, October 08, 2001, 8:41:18 PM, Glen wrote:
GM> that *I* would do is:
GM> dpkg --purge pcmcia-cs
GM> apt-get install pcmcia-cs
GM> the first command will purge your config files, and the second will
reinstall (and reconfig) the pcmcia access.
Did that, and I now got the chance to configure my PCMCIA card (found
out you could do a /usr/sbin/psnetconfig instead).
What are frame type and IPX network number, and do I need them?
GM> you could have a look at the docs on linuxdoc.org (or in
/usr/share/doc/en-HOWTO/pcmcia-cs, if you installed doc-linux text) on pcmcia
as to what the pcmcia options are, and what kernel modules
GM> you'll need for pcmcia support for *your* card.
Eeeh ok, that sounds hard for a newbie like me - kernel modules?? Do I
even dare to mess with my kernel?
>> GM> /etc/init.d/pcmcia {start|stop|restart} ?
>> stopping PCMCIA services: cardmgr modules
>> starting PCMCIA services: cardmgr modules
>>
>> But I have no network access!? I have at no time specified xirc2ps as
>> my driver, shouldn't I? What do I do now? Can I deinstall (apt-get
>> deinstall pcmcia-cs) and reinstall, and would that help me?
>>
>> >> GM> try 'apt-get install pcmcia-cs'
>> >> It claims to have the latest version of pcmcia-cs
>> >>
>> >> GM> you'll need to know the chipset of your card, as well as whether or
>> >> not your card is pcmcia or cardbus-- check the hardware-HOWTO at
>> >> http://www.linuxdoc.org/
>> >> By chipset, do you then mean something like xirc2ps?
>> >>
>> >> Ok it looks like I have what I need, but how do I set it up, and get
>> >> it running?
>> >>
>> >> >> >> I'm trying to install on a Dell Inspiron 7500, and I have gotten
>> >> >> >> some hints from some
>> >> >> >> of you earlier. But I can't figure out where I setup the PCMCIA card
>> >> >> >> during the setup (Xircom 10/100/56). The only thing I am asked
>> >> >> >> about my PCMCIA card, is
>> >> >> >> whether it's a intel thing or some T... thing. Where do I specify
>> >> >> >> that
>> >> >> >> it's a xirc2ps? I can't setup my network if I specify intel or T....
>> >> >>
>> >> >> JC> During the PCMCIA installation, you are asked to enter any
>> >> >> JC> card-specific options as well as a controller type, e.g. i82365.
>> >> >> JC> After these options are entered and the card services are
>> >> >> JC> installed, you can then configure the Network. If the install
>> >> >> JC> process doesn't prompt you directly, you can choose it from the
>> >> >> JC> list of alternative options below the recommended options in the
>> >> >> JC> installation script. You don't specify the module to load, it is
>> >> >> JC> automatically detected by the card services. If it doesn't
>> >> >> JC> detect the correct card module, you can go into a console from
>> >> >> JC> the installation script and make some changes to the pcmcia
>> >> >> JC> config options to help the auto-detect process.
>> >> >> Well... I finally got my Debian installed with X running (thanks to
>> >> >> you). I still have no network running, but I don't want to reinstall
>> >> >> if I can avoid it. How do I get this up and running? I can't apt-get
>> >> >> from the net (off course), so I have to get whatever I need from my
>> >> >> CD. What do I do? Can I run some sort of installer, that can help me?
--
Med venlig hilsen/Best regards,
Søren Neigaard mailto:[EMAIL PROTECTED]
