Hi,
Both my ethernet Controller and the cardbus are using the same interrupt
and I'm told this is suboptimal as it is sharing it with USB. PCMCIA is
working but USB is not(2.2.19 kernel).
How can I update /etc/pcmcia.conf to remedy this?
Here is the USB and the PCMCIA dmesg output. The first part of the
message prints out
options: [pci] [cardbus] [apm]
Should this be set to something as well?
Thanks for help,
Eric
usb-uhci.c: USB UHCI at I/O 0xf300, IRQ 10
Linux PCMCIA Card Services 3.1.22
kernel build: 2.2.19 #1 Thu Apr 19 22:35:28 EST 2001
options: [pci] [cardbus] [apm]
PCI routing table version 1.0 at 0xfe840
Intel PCIC probe:
TI 1225 rev 01 PCI-to-CardBus at slot 00:0a, mem 0x68000000
host opts [0]: [serial pci & irq] [pci irq 10] [lat 168/176] [bus
32/34]
host opts [1]: [serial pci & irq] [pci irq 10] [lat 168/176] [bus
35/37]
ISA irqs (scanned) = 3,4,7,9,11 PCI status changes
cs: IO port probe 0x0c00-0x0cff: excluding 0xcf8-0xcff
cs: IO port probe 0x0800-0x08ff: excluding 0x800-0x807
cs: IO port probe 0x0100-0x04ff: excluding 0x300-0x307 0x378-0x37f
0x388-0x38f 0x3e8-0x3ff 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
cs: cb_alloc(bus 35): vendor 0x1011, device 0x0019
ROM image dump:
image 0: 0x000000-0x0001ff, signature PCIR
cs: cb_config(bus 35)
fn 0 bar 1: io 0x400-0x47f
fn 0 bar 2: mem 0x600c0000-0x600c007f
fn 0 rom: mem 0x60080000-0x600bffff
irq 10
cs: cb_enable(bus 35)
bridge io map 0 (flags 0x21): 0x400-0x47f
bridge mem map 0 (flags 0x1): 0x60080000-0x600c0fff
tulip_attach(device 23:00.0)
tulip.c:v0.91g-ppc 7/16/99 [EMAIL PROTECTED] (modified by
[EMAIL PROTECTED] for XIRCOM CBE, fixed by Doug Ledford)
eth0: Digital DS21143 Tulip rev 48 at 0x400, 00:10:7A:10:E1:DB, IRQ 10.
eth0: EEPROM default media type Autosense.
eth0: Index #0 - Media 10baseT (#0) described by a 21142 Serial PHY (2)
block.
eth0: Index #1 - Media 10baseT-FD (#4) described by a 21142 Serial PHY
(2) block.
eth0: Index #2 - Media 100baseTx (#3) described by a 21143 SYM PHY (4)
block.eth0: Index #3 - Media 100baseTx-FD (#5) described by a 21143 SYM
PHY (4) block.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
tty04 at 0x0ae8 (irq = 3) is a 16550A
