I've discovered an update to Linmodems' Page about Lucent Modem for the
2.2 and 2.4 kernels ( http://walbran.org/sean/linux/stodolsk/ ).
I'm a Debian user (potato, kernel version 2.2.17) and I installed
successfully ltmodem driver. When I used 2.2.12 kernel, original ltmodem
driver was perfect. But this last one driver doesn't run.
At Sean's page above, there was an information:
"If the installation goes smoothly, but you get a 'No Dialtone' response
from the modem, you might be able to fix it by changing the BIOS
Plug-n-Play settings: select "non-PNP OS" or "Other OS" rather than the
(probable default) "PNP OS" or "Windows." Check also if the modem has a
nonzero IRQ value by issuing the command lspci -vv and looking for your
modem card in the output."
I have a Compaq Armada 1500C and I get a NO DIALTONE from modem, but I
can't change BIOS settings (there isn't these options).
Have you any suggestion?
Thanks a lot!
Carlos Menezes.
PS.: Some useful informations are appended :
WVDIAL.CONF:
[Dialer Defaults]
Modem = /dev/modem
Baud = 57600
Init = ATZ
Phone = 35555000
Username = ig
Password = ig
[Dialer pulse]
Dial Command = ATDP
OUTPUT OF LSPCI -VV:
00:00.0 Host bridge: Intel Corporation 440BX/ZX - 82443BX/ZX Host bridge
(AGP disabled) (rev 03)
Subsystem: Compaq Computer Corporation: Unknown device 0540
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 64 set
Region 0: Memory at 50000000 (32-bit, prefetchable)
00:07.0 ISA bridge: Intel Corporation 82371AB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 set
00:07.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01)
(prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 set
Region 4: I/O ports at 1020
00:07.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01)
(prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 set
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at 1000
00:07.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 02)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00:08.0 VGA compatible controller: Chips and Technologies F69000
HiQVideo (rev 64) (prog-if 00 [VGA])
Subsystem: Compaq Computer Corporation: Unknown device b101
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 0
Region 0: Memory at 40000000 (32-bit, non-prefetchable)
00:11.0 CardBus bridge: Texas Instruments PCI1225 (rev 01)
Subsystem: Texas Instruments: Unknown device ac1c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 66 set, cache line size 08
Interrupt: pin A routed to IRQ 0
Region 0: Memory at 7fffe000 (32-bit, non-prefetchable)
Bus: primary=00, secondary=01, subordinate=01, sec-latency=176
I/O window 0: 00000000-00000003
I/O window 1: 00000000-00000003
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0007
00:11.1 CardBus bridge: Texas Instruments PCI1225 (rev 01)
Subsystem: Texas Instruments: Unknown device ac1c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 66 set, cache line size 08
Interrupt: pin A routed to IRQ 0
Region 0: Memory at 7ffff000 (32-bit, non-prefetchable)
Bus: primary=00, secondary=02, subordinate=02, sec-latency=176
I/O window 0: 00000000-00000003
I/O window 1: 00000000-00000003
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0007
OUTPUT OF DMESG:
Linux version 2.2.17 ([EMAIL PROTECTED]) (gcc version 2.95.2 20000313
(Debian GNU/Linux)) #1 Sun Jun 25 09:24:41 EST 2000
Detected 366685 kHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 732.36 BogoMIPS
Memory: 62096k/65472k available (1732k kernel code, 416k reserved, 1088k
data, 140k init)
Dentry hash table entries: 8192 (order 4, 64k)
Buffer cache hash table entries: 65536 (order 6, 256k)
Page cache hash table entries: 16384 (order 4, 64k)
VFS: Diskquotas version dquot_6.4.0 initialized
CPU: Intel Celeron (Mendocino) stepping 0a
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.35a (19990819) Richard Gooch ([EMAIL PROTECTED])
PCI: PCI BIOS revision 2.10 entry at 0xf0484
PCI: Using configuration type 1
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
TCP: Hash tables configured (ehash 65536 bhash 65536)
Starting kswapd v 1.5
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.13)
apm: disabled on user request.
Real Time Clock Driver v1.09
RAM disk driver initialized: 16 RAM disks of 4096K size
loop: registered device at major 7
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1020-0x1027, BIOS settings: hda:DMA, hdb:DMA
hda: IBM-DBCA-204860, ATA DISK drive
hdb: TOSHIBA CD-ROM XM-1902B, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: IBM-DBCA-204860, 4108MB w/420kB Cache, CHS=556/240/63
hdb: ATAPI 24X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.11
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
md driver 0.36.6 MAX_MD_DEV=4, MAX_REAL=8
scsi: <fdomain> Detection failed (no card)
NCR53c406a: no available ports found
sym53c416.c: Version 1.0.0
Failed initialization of WD-7000 SCSI card!
IBM MCA SCSI: No Microchannel-bus support present -> Aborting.
megaraid: v107 (December 22, 1999)
aec671x_detect:
3w-xxxx: tw_findcards(): No cards found.
scsi : 0 hosts.
scsi : detected total.
Partition check:
hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 140k freed
NET4: Unix domain sockets 1.0 for Linux NET4.0.
Adding Swap: 68004k swap-space (priority -1)
parport0: PC-style at 0x378 [SPP,PS2]
parport_probe: failed
parport0: no IEEE-1284 device present.
Soundblaster audio driver Copyright (C) by Hannu Savolainen 1993-1996
SB 3.01 detected OK (220)
ESS chip ES1869 detected
Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED])
YM3812 and OPL-3 driver Copyright (C) by Hannu Savolainen, Rob Hooft
1993-1996
Serial driver version 4.27 with no serial options enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
Linux PCMCIA Card Services 3.1.8
kernel build: 2.2.17 unknown
options: [pci] [cardbus] [apm]
Intel PCIC probe:
TI 1225 PCI-to-CardBus at bus 0 slot 17, mem 0x7fffe000, 2 sockets
host opts [0]: [ring] [pwr save] [pci + serial irq] [no pci irq]
[lat 66/176] [bus 1/1]
host opts [1]: [ring] [pwr save] [pci + serial irq] [no pci irq]
[lat 66/176] [bus 2/2]
ISA irqs (scanned) = 3,4,7,9,10,15 status change on irq 15
cs: IO port probe 0x1000-0x17ff: excluding 0x1000-0x102f
cs: IO port probe 0x0100-0x04ff: excluding 0x250-0x257 0x260-0x267
0x378-0x37f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
eth0: NE2000 Compatible: io 0x300, irq 3, hw_addr 00:50:BA:73:0D:13
Lucent Modem driver version 5.78 with no serial options enabled
ttyLT00 at 0x0260 (irq = 3) is a Lucent
Unloading Lucent Modem driver: version 5.78
Lucent Modem driver version 5.78 with no serial options enabled
ttyLT00 at 0x0260 (irq = 3) is a Lucent
