Hi there,
though I browsed the archives I could not find a
solution to my problem. If it has been tackled, any
URL is a good URL. ;-)
My problem is this:
I'm in kinda situation and bound to use my old laptop,
an Compaq Armada 1500c. Unfortunately, the USB port is
broken. I bought a USB 2.0 Hi-Speed CardBus Adapter
PCMUSB20A and I'm trying to make it work.
I'm using
hotplug 0.0.200403
cardmgr 3.2.5
Linux 2.6.8-1-686 #1 Thu Oct 7 03:15:25 EDT 2004 i686
GNU/Linux
I didn't do anything yet, sorry, couldn't find any doc
on how to start installing the CardBus USB adapter.
When I insert it into the slot, /var/log/messages
displays:
Oct 31 21:30:29 kernel: Linux Kernel Card Services
Oct 31 21:30:29 kernel: options: [pci] [cardbus]
[pm]
Oct 31 21:30:29 kernel: ACPI: PCI interrupt
0000:00:11.0[A] -> GSI 11 (level, low) -> IRQ 11
Oct 31 21:30:29 kernel: Yenta: CardBus bridge found at
0000:00:11.0 [0e11:b121]
Oct 31 21:30:29 kernel: Yenta: Enabling burst memory
read transactions
Oct 31 21:30:29 kernel: Yenta: Using CSCINT to route
CSC interrupts to PCI
Oct 31 21:30:29 kernel: Yenta: Routing CardBus
interrupts to PCI
Oct 31 21:30:29 kernel: Yenta TI: socket 0000:00:11.0,
mfunc 0x01001c72, devctl 0x64
Oct 31 21:30:29 kernel: Yenta: ISA IRQ mask 0x0408,
PCI irq 11
Oct 31 21:30:29 kernel: Socket status: 30000006
Oct 31 21:30:29 kernel: ACPI: PCI interrupt
0000:00:11.1[A] -> GSI 11 (level, low) -> IRQ 11
Oct 31 21:30:29 kernel: Yenta: CardBus bridge found at
0000:00:11.1 [0e11:b121]
Oct 31 21:30:29 kernel: Yenta: Using CSCINT to route
CSC interrupts to PCI
Oct 31 21:30:29 kernel: Yenta: Routing CardBus
interrupts to PCI
Oct 31 21:30:29 kernel: Yenta TI: socket 0000:00:11.1,
mfunc 0x01001c72, devctl 0x64
Oct 31 21:30:29 kernel: Yenta: ISA IRQ mask 0x0408,
PCI irq 11
Oct 31 21:30:29 kernel: Socket status: 30000020
Oct 31 21:30:31 kernel: [__report_bad_irq+42/144]
__report_bad_irq+0x2a/0x90
Oct 31 21:30:31 kernel: [note_interrupt+112/176]
note_interrupt+0x70/0xb0
Oct 31 21:30:31 kernel: [do_IRQ+288/304]
do_IRQ+0x120/0x130
Oct 31 21:30:31 kernel: [common_interrupt+24/32]
common_interrupt+0x18/0x20
Oct 31 21:30:31 kernel: [__do_softirq+46/128]
__do_softirq+0x2e/0x80
Oct 31 21:30:31 kernel: [do_softirq+39/48]
do_softirq+0x27/0x30
Oct 31 21:30:31 kernel: [do_IRQ+251/304]
do_IRQ+0xfb/0x130
Oct 31 21:30:31 kernel: [common_interrupt+24/32]
common_interrupt+0x18/0x20
Oct 31 21:30:31 kernel: [schedule+907/1232]
schedule+0x38b/0x4d0
Oct 31 21:30:31 kernel: [default_idle+35/64]
default_idle+0x23/0x40
Oct 31 21:30:31 kernel: [cpu_idle+52/64]
cpu_idle+0x34/0x40
Oct 31 21:30:31 kernel: [start_kernel+424/496]
start_kernel+0x1a8/0x1f0
Oct 31 21:30:31 kernel: [unknown_bootoption+0/352]
unknown_bootoption+0x0/0x160
Oct 31 21:30:32 kernel: cs: IO port probe
0x0100-0x04ff: excluding 0x250-0x257 0x330-0x337
0x388-0x38f 0x4d0-0x4d7
Oct 31 21:30:32 kernel: cs: IO port probe
0x0800-0x08ff: clean.
Oct 31 21:30:32 kernel: cs: IO port probe
0x0c00-0x0cff: clean.
Oct 31 21:30:32 kernel: cs: IO port probe
0x0a00-0x0aff: clean.
Oct 31 21:30:36 pci.agent[2063]: ehci-hcd: loaded
successfully
Oct 31 21:30:37 kernel: PCI: Enabling device
0000:05:00.3 (0000 -> 0002)
Oct 31 21:30:37 kernel: ACPI: PCI interrupt
0000:05:00.3[A] -> GSI 11 (level, low) -> IRQ 11
Oct 31 21:30:37 kernel: ehci_hcd 0000:05:00.3: ALi
Corporation USB 2.0 Controller
Oct 31 21:30:37 kernel: ehci_hcd 0000:05:00.3: irq 11,
pci mem caa06000
Oct 31 21:30:37 kernel: ehci_hcd 0000:05:00.3: new USB
bus registered, assigned bus number 1
Oct 31 21:30:37 kernel: ehci_hcd 0000:05:00.3: USB 2.0
enabled, EHCI 1.00, driver 2004-May-10
Oct 31 21:30:37 kernel: hub 1-0:1.0: USB hub found
Oct 31 21:30:37 kernel: hub 1-0:1.0: 6 ports detected
Oct 31 21:30:37 kernel: PCI: Enabling device
0000:05:00.0 (0000 -> 0002)
Oct 31 21:30:37 kernel: ACPI: PCI interrupt
0000:05:00.0[A] -> GSI 11 (level, low) -> IRQ 11
Oct 31 21:30:37 kernel: ohci_hcd 0000:05:00.0: ALi
Corporation USB 1.1 Controller
Oct 31 21:30:37 pci.agent[2059]: ohci-hcd: loaded
successfully
Oct 31 21:30:37 kernel: ohci_hcd 0000:05:00.0: irq 11,
pci mem caa58000
Oct 31 21:30:37 kernel: ohci_hcd 0000:05:00.0: new USB
bus registered, assigned bus number 2
Oct 31 21:30:37 kernel: hub 2-0:1.0: USB hub found
Oct 31 21:30:37 kernel: hub 2-0:1.0: 2 ports detected
Oct 31 21:30:40 kernel: usb 2-1: new full speed USB
device using address 2
Oct 31 21:30:41 usb.agent[2123]: usbcore: already
loaded
Oct 31 21:30:42 usb.agent[2163]: usbcore: already
loaded
Oct 31 21:30:45 kernel: usb 2-1: control timeout on
ep0out
Oct 31 21:30:45 kernel: ohci_hcd 0000:05:00.0: Unlink
after no-IRQ? Different ACPI or APIC settings may
help.
Then, I attach a USB stick and - it blinks! When the
standard USB port still worked, I was able to mount it
as /dev/sda1 - now, I can't access it, at least I
don't know how.
If you're still with me:
- How can I test if the adapter works?
- It doesn't seem to work, honestly, since I cannot
access the USB stick. Where can I find information on
how to make it work?
Thanks!
cu,
Tom
___________________________________________________________ALL-NEW Yahoo! Messenger -
all new features - even more fun! http://uk.messenger.yahoo.com
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
