On Sun, 13 Jul 2003 06:08, mi wrote: > > Here is the contents of my /etc/default/pcmcia: > > # Defaults for pcmcia (sourced by /etc/init.d/pcmcia) > > PCMCIA=yes > > PCIC=i82365 > > PCIC_OPTS= > > CORE_OPTS= > > CARDMGR_OPTS= > > Are there any specific changes that you recommend I should try? > > yes, try PCIC=yenta_socket
OK I did that, the yenta driver is loaded on a reboot, and the result is the same. The device driver for my ethernet card gets loaded, but the interface is not configured. I did some tracing on the /etc/pcmcia/network script which is not being run at all, this seems to be at the core of the problem. I've attached a relevant section of my kernel message log for removing a card and inserting it again. Also for some reason my machine does not beep when the card is inserted. > Great stuff, SELinux ! Good luck to this. Thanks. -- http://www.coker.com.au/selinux/ My NSA Security Enhanced Linux packages http://www.coker.com.au/bonnie++/ Bonnie++ hard drive benchmark http://www.coker.com.au/postal/ Postal SMTP/POP benchmark http://www.coker.com.au/~russell/ My home page
cs: cb_free(bus 5) cs: cb_alloc(bus 5): vendor 0x10b7, device 0x5157 PCI: Enabling device 05:00.0 (0000 -> 0003) See Documentation/networking/vortex.txt 05:00.0: 3Com PCI 3CCFE575BT Cyclone CardBus at 0x4800. Vers LK1.1.16 PCI: Setting latency timer of device 05:00.0 to 64 00:50:04:94:da:23, IRQ 10 product code 5457 rev 07.1 date 06-14-99 05:00.0: CardBus functions mapped 18c00080->d9717080 Internal config register is 600000, transceivers 0x40. 8K byte-wide RAM 5:3 Rx:Tx split, MII interface. MII transceiver found at address 0, status 7809. Enabling bus-master transmits and whole-frame receives. 05:00.0: scatter/gather enabled. h/w checksums enabled cs: cb_free(bus 5) unloading Kernel Card Services Linux Kernel Card Services 3.1.22 options: [pci] [cardbus] [pm] PCI: Found IRQ 11 for device 00:02.0 PCI: Sharing IRQ 11 with 00:05.0 PCI: Sharing IRQ 11 with 01:00.0 PCI: Found IRQ 10 for device 00:02.1 Yenta IRQ list 0088, PCI irq11 Socket status: 30000006 Yenta IRQ list 0088, PCI irq10 Socket status: 30000006 cs: IO port probe 0x0c00-0x0cff: clean. cs: IO port probe 0x0800-0x08ff: clean. cs: IO port probe 0x0100-0x04ff: excluding 0x170-0x177 0x370-0x377 0x3b8-0x3df 0x4d0-0x4d7 cs: IO port probe 0x0a00-0x0aff: clean. cs: cb_alloc(bus 5): vendor 0x10b7, device 0x5157 PCI: Enabling device 05:00.0 (0000 -> 0003) See Documentation/networking/vortex.txt 05:00.0: 3Com PCI 3CCFE575BT Cyclone CardBus at 0x4800. Vers LK1.1.16 PCI: Setting latency timer of device 05:00.0 to 64 00:50:04:94:da:23, IRQ 10 product code 5457 rev 07.1 date 06-14-99 05:00.0: CardBus functions mapped 18c00080->d9719080 Internal config register is 600000, transceivers 0x40. 8K byte-wide RAM 5:3 Rx:Tx split, MII interface. MII transceiver found at address 0, status 7809. Enabling bus-master transmits and whole-frame receives. 05:00.0: scatter/gather enabled. h/w checksums enabled cs: cb_free(bus 5) cs: cb_alloc(bus 5): vendor 0x10b7, device 0x5157 PCI: Enabling device 05:00.0 (0000 -> 0003) See Documentation/networking/vortex.txt 05:00.0: 3Com PCI 3CCFE575BT Cyclone CardBus at 0x4800. Vers LK1.1.16 PCI: Setting latency timer of device 05:00.0 to 64 00:50:04:94:da:23, IRQ 10 product code 5457 rev 07.1 date 06-14-99 05:00.0: CardBus functions mapped 18c00080->d971b080 Internal config register is 600000, transceivers 0x40. 8K byte-wide RAM 5:3 Rx:Tx split, MII interface. MII transceiver found at address 0, status 7809. Enabling bus-master transmits and whole-frame receives. 05:00.0: scatter/gather enabled. h/w checksums enabled
