Eric Richardson <[EMAIL PROTECTED]> writes: > What does lsmod report? > > My networking stuff looks like this for 2.2.x kernel. > maxwell@maxwell:~/app$ lsmod > Module Size Used by > serial_cs 4980 0 (unused) > tulip_cb 30104 2 > cb_enabler 2296 2 [tulip_cb] > ds 6028 2 [serial_cs cb_enabler] > i82365 21072 2 > pcmcia_core 42384 0 [serial_cs cb_enabler ds i82365] > > If yours is not similar then you should run modconf as root and > select some modules.
After loading pcnet_cs "manually" it looks somewhat similar. The main difference seems to be the "Used" "0" for pcnet_cs, 8390 and pcmcia_core. Does this give some indication what could be the problem? Module Size Used by pcnet_cs 10340 0 (unused) 8390 5916 0 [pcnet_cs] ds 6028 2 [pcnet_cs] i82365 21072 2 pcmcia_core 42384 0 [pcnet_cs ds i82365] nls_cp437 3872 4 (autoclean) slip 7232 0 (unused) ppp 20296 0 (unused) slhc 4368 0 [slip ppp] binfmt_misc 3800 0 binfmt_aout 3936 0 autofs 9140 0 (unused) smbfs 24928 0 (unused) vfat 9404 2 unix 11332 97 (autoclean) > Use the pcnet_cs as suggested by Bruce instead of tulip_cb as in my > situation. The serial_cs is for my modem card I believe. > > > Hope this helps, > Eric > p.s. unload any modules that you don't need when running modconf if > the drivers won't load. The modules load without problem. I did remove slip, ppp and slhc for a try anyway. It didn't help. Thanks again! Andreas > Andreas Goesele wrote: > > > Hi, > > I already lost much too much time trying to get PCMCIA work on my > > > laptop (Samsung MV7000, potato, kernel 2.2.19, corega FEther > > PCC-TXF). The card works under Win98. > > When I put in the card, I get one deep beep, removing it one high > > > beep. The card is recognized and the modules seem to be loaded > > alright. But ifconfig doesn't show eth0 and consequently a ping > > results in "network is unreachable". The network information > > (ip-address, network, netmask, gateway, broadcast) in network.conf is > > most certainly correct. (But see below under 6.) > > Trying to run the network script by hand invariably gives: > > > /etc/pcmcia/network start eth0 > > > usage: /etc/pcmcia/network [action] [device name] > > > actions: start check stop suspend resume > > As I have exhausted all my possibility (re-reading various times the > > > PCMCIA-HOWTO, playing around with various settings ...) I would be > > very grateful for some help! > > Follows all the info I could get. (1. system log, 2. cardctl status, > > > 3. cardctl config, 4. cardctl ident, 5. test_setup, 6. test_network, > > 7. dump_pirq > > 1) In the system log I have: > > > Oct 13 19:49:43 debi kernel: Linux PCMCIA Card Services 3.1.22 > > > Oct 13 19:49:43 debi kernel: kernel build: 2.2.19 #1 Wed Mar 20 19:41:41 EST 2002 > > Oct 13 19:49:43 debi kernel: options: [pci] [cardbus] [apm] > > Oct 13 19:49:43 debi kernel: PCI routing table version 1.0 at 0xfdf60 > > Oct 13 19:49:43 debi kernel: 00:08.1 -> irq 5 > > Oct 13 19:49:43 debi kernel: Intel PCIC probe: > > Oct 13 19:49:43 debi kernel: Ricoh RL5C478 rev 80 PCI-to-CardBus at slot 00:08, >mem 0x68000000 > > Oct 13 19:49:43 debi kernel: host opts [0]: [serial irq] [io 3/6/1] [mem >3/6/1] [pci irq 11] [lat 168/176] [bus 32/34] > > Oct 13 19:49:43 debi kernel: host opts [1]: [serial irq] [io 3/6/1] [mem >3/6/1] [pci irq 5] [lat 168/176] [bus 35/37] > > Oct 13 19:49:43 debi kernel: ISA irqs (default) = 3,4,7,9,10,12,15 PCI status >changes > > Oct 13 19:49:44 debi kernel: cs: IO port probe 0x0c00-0x0cff: excluding 0xcf8-0xcff > > Oct 13 19:49:44 debi kernel: cs: IO port probe 0x0800-0x08ff: clean. > > Oct 13 19:49:44 debi kernel: cs: IO port probe 0x0100-0x04ff: excluding >0x378-0x37f 0x398-0x39f 0x4d0-0x4d7 > > Oct 13 19:49:44 debi kernel: cs: IO port probe 0x0a00-0x0aff: clean. > > Oct 13 19:49:44 debi kernel: cs: memory probe 0xa0000000-0xa0ffffff: clean. > > According to the PCMCIA Howto the 10th line should continue and look > > > as for instance: Could that be relevant? > > > 2) Output of cardctl status: > > > Socket 0: > > > 5V 16-bit PC Card > > function 0: [ready], [wp] > > Socket 1: > > no card > > 3) Output of cardctl config: > > > Socket 0: > > > Vcc 5.0V Vpp1 5.0V Vpp2 5.0V > > Socket 1: > > not configured > > 4) Output of cardctl ident: > > > Socket 0: > > > product info: "corega", "FEther PCC-TXF" > > manfid: 0xc00f, 0x0000 > > function: 6 (network) > > Socket 1: > > no product info available > > 5) Output of test_setup: > > > Current kernel: 2.2.19 #1 Wed Mar 20 19:41:41 EST 2002 > > > Module info from /lib/modules/2.2.19/pcmcia/pcmcia_core.o: > > Linux PCMCIA Card Services 3.1.22 > > options: [pci] [cardbus] [apm] > > Startup options from /etc/pcmcia.conf: > > > PCMCIA=yes > > PCIC=i82365 > > PCIC_OPTS= > > CORE_OPTS= > > CARDMGR_OPTS= > > Checking current syslog files in /var/log: > > > All PCMCIA messages are in /var/log/syslog. > > Module status: > > > The PCMCIA kernel modules are loaded correctly. > > Daemon status: > > > cardmgr is running (process 168) > > Current socket status from /var/lib/pcmcia/stab: > > > Socket 0: empty > > Socket 1: empty > > 6) Output of test_network: > > > PCMCIA network settings are coming from /etc/pcmcia/network.opts. > > > No PCMCIA network interfaces are configured. > > There is a network device in socket 0: > > > empty > > 7) Output of dump_pirq: > > > Interrupt routing table found at address 0xfdf60: > > > Version 1.0, size 0x0080 > > Interrupt router is device 00:07.0 > > PCI exclusive interrupt mask: 0x0000 [] > > Compatible router: vendor 0x8086 device 0x122e > > Device 00:07.0 (slot 0): ISA bridge > > > INTD: link 0x63, irq mask 0x0800 [11] > > Device 00:08.0 (slot 0): CardBus bridge > > > INTA: link 0x60, irq mask 0x0800 [11] > > INTB: link 0x61, irq mask 0x0020 [5] > > Device 00:0b.0 (slot 0): VGA compatible controller > > > INTA: link 0x62, irq mask 0x0400 [10] > > Device 00:09.0 (slot 0): INTA: link 0x60, irq mask 0x0800 [11] > > > Device 00:0a.0 (slot 0): INTA: link 0x61, irq mask 0x0020 [5] > > > Device 00:00.0 (slot 0): Host bridge > > > INTA: link 0x60, irq mask 0xdef8 [3,4,5,6,7,9,10,11,12,14,15] > > INTB: link 0x61, irq mask 0x0020 [5] > > INTC: link 0x62, irq mask 0xdef8 [3,4,5,6,7,9,10,11,12,14,15] > > INTD: link 0x63, irq mask 0xdef8 [3,4,5,6,7,9,10,11,12,14,15] > > Interrupt router at 00:07.0: Intel 82443MX PCI-to-ISA bridge > > > PIRQ1 (link 0x60): irq 11 > > PIRQ2 (link 0x61): irq 5 > > PIRQ3 (link 0x62): unrouted > > PIRQ4 (link 0x63): irq 11 > > Serial IRQ: [enabled] [continuous] [frame=21] [pulse=4] > > Level mask: 0x0820 [5,11] -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
