-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I asked this maybe a few weeks ago, but realy nobody did any replay so i post again, and hope that this time there are some people who may help me :-) *please* ;-) i use kernel 2.2.19 / 2.4.3 and pcmcia-cs-3.1.25 and debian 2.2 r2 potato my first try was with 2.2.19 and after a short while all my attempts to get the pcmcia slots running succeded :) but with 2.4.3 nothing is working as i'm used to with 2.2.19 ok first i tryed with .config_2.4.3 in short i tried this: ============================= # # PCMCIA/CardBus support # # CONFIG_PCMCIA is not set CONFIG_SYSVIPC=y # CONFIG_BSD_PROCESS_ACCT is not set CONFIG_SYSCTL=y CONFIG_KCORE_ELF=y # CONFIG_KCORE_AOUT is not set CONFIG_BINFMT_AOUT=y CONFIG_BINFMT_ELF=y CONFIG_BINFMT_MISC=y CONFIG_PM=y CONFIG_APM=y # CONFIG_APM_IGNORE_USER_SUSPEND is not set # CONFIG_APM_DO_ENABLE is not set CONFIG_APM_CPU_IDLE=y # CONFIG_APM_DISPLAY_BLANK is not set # CONFIG_APM_RTC_IS_GMT is not set # CONFIG_APM_ALLOW_INTS is not set CONFIG_APM_REAL_MODE_POWER_OFF=y ================================ and then i compiled the modules as i did for 2.2.19: make clean make config make all make install ( i have included the make config in config_pcmcia_cs-3.1.25 as attachement ) then i tried to load the modules with /etc/init.d/pcmcia stop/start but i got a lot of errors the led on the networkcard lit and a peep i could notice but i didn't work later i tried the konfigurations as above ================================= # # PCMCIA/CardBus support # CONFIG_PCMCIA=m CONFIG_CARDBUS=y CONFIG_I82365=y # CONFIG_TCIC is not set CONFIG_SYSVIPC=y # CONFIG_BSD_PROCESS_ACCT is not set CONFIG_SYSCTL=y CONFIG_KCORE_ELF=y # CONFIG_KCORE_AOUT is not set CONFIG_BINFMT_AOUT=y CONFIG_BINFMT_ELF=y CONFIG_BINFMT_MISC=y CONFIG_PM=y CONFIG_APM=y # CONFIG_APM_IGNORE_USER_SUSPEND is not set # CONFIG_APM_DO_ENABLE is not set CONFIG_APM_CPU_IDLE=y # CONFIG_APM_DISPLAY_BLANK is not set # CONFIG_APM_RTC_IS_GMT is not set # CONFIG_APM_ALLOW_INTS is not set CONFIG_APM_REAL_MODE_POWER_OFF=y ======================================= i got the following results: Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters OR /lib/modules/2.4.3/kernel/drivers/pcmcia/ds.o: init_module: Operation not permitted /lib/modules/2.4.3/kernel/drivers/pcmcia/ds.o: insmod /lib/modules/2.4.3/kernel/drivers/pcmcia/ds.o failed /lib/modules/2.4.3/kernel/drivers/pcmcia/ds.o: insmod ds failed Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters ??? what shoul i do now??? the module(s) ds.o i82365.o pcnet_cs.o yenta_socket.o don't work anymore because of this faults and now i duno what to do? if someone could pass me some hints i would be very happy :)) - -- From: Joachim Schiele [ http://www.dune2.de || Linux - my way! ] -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.0.4 (GNU/Linux) Comment: For info see http://www.gnupg.org iEYEARECAAYFAjrl8I8ACgkQeGYPq/O+yerLngCgtTnH9D0sYtV+YprrWLsr6e8H +rIAn2f+9SN5bjuzerkKOZ3ltijtPvpI =JUoa -----END PGP SIGNATURE----- -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
