Package: src:linux Version: 3.16.7-2 Severity: normal Dear Maintainer,
upgrading Debian Wheezy (3.2) to Jessie (3.16) renders internal clocksource unstable. ntpd cannot keep up. Jitter is high. As soon as HPET is enabled and intel_idle.max_cstate=1 is passed the clocksource stays with tsc and remains stable. The HPET gets force enabled in upstream already: https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/arch/x86/kernel/quirks.c?id=2e151c70dfb0075ff83bec305c52a9da1ba49089 This patch does apply to 3.16. Before (without patch): [ 0.733124] Switched to clocksource refined-jiffies [ 3.522316] rtc_cmos rtc_cmos: setting system clock to 2014-12-12 11:21:12 UTC (1418383272) [ 3.784535] PTP clock support registered [ 4.254188] Switched to clocksource tsc [ 9.367378] Clocksource tsc unstable (delta = 551964647 ns) [ 9.481069] Switched to clocksource refined-jiffies After (with patch): [ 0.749132] hpet clockevent registered [ 0.773076] Switched to clocksource hpet [ 6.317316] tsc: Refined TSC clocksource calibration: 999.999 MHz [ 8.865569] Switched to clocksource tsc [ 9.223725] rtc_cmos rtc_cmos: setting system clock to 2014-12-12 11:06:52 UTC (1418382412) [ 9.835758] PTP clock support registered Please consider including for the Jessie kernel. Thank you, Martin Sofaru -- Package-specific info: ** Version: Linux version 3.16.0-4-amd64 (debian-kernel@lists.debian.org) (gcc version 4.8.3 (Debian 4.8.3-13) ) #1 SMP Debian 3.16.7-2 (2014-11-06) ** Command line: BOOT_IMAGE=/vmlinuz-3.16.0-4-amd64 root=UUID=f9376d02-5ef8-482b-8262-a8ba4ca98590 ro console=ttyS0,19200 elevator=noop intel_idle.max_cstate=1 pcie_aspm=off 8250.nr_uarts=2 i8042.noaux i8042.nokbd ** Not tainted ** Kernel log: [ 9.481293] e1000e 0000:0b:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 9.481372] e1000e 0000:0b:00.0: irq 50 for MSI/MSI-X [ 9.481392] e1000e 0000:0b:00.0: irq 51 for MSI/MSI-X [ 9.481412] e1000e 0000:0b:00.0: irq 52 for MSI/MSI-X [ 9.618330] e1000e 0000:0b:00.0 eth3: registered PHC clock [ 9.649073] e1000e 0000:0b:00.0 eth3: (PCI Express:2.5GT/s:Width x1) 00:00:24:ce:6d:0f [ 9.697069] e1000e 0000:0b:00.0 eth3: Intel(R) PRO/1000 Network Connection [ 9.737161] e1000e 0000:0b:00.0 eth3: MAC: 3, PHY: 8, PBA No: FFFFFF-0FF [ 9.843741] PM: Starting manual resume from disk [ 9.845248] PM: Hibernation image partition 8:7 present [ 9.845256] PM: Looking for hibernation image. [ 9.845692] PM: Image not found (code -22) [ 9.845692] PM: Hibernation image not present or could not be loaded. [ 9.881273] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null) [ 10.175560] systemd[1]: systemd 215 running in system mode. (+PAM +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ -SECCOMP -APPARMOR) [ 10.177583] systemd[1]: Detected architecture 'x86-64'. [ 10.261502] systemd[1]: Inserted module 'autofs4' [ 10.266736] systemd[1]: Set hostname to <jessie>. [ 10.507650] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory. [ 10.598465] systemd[1]: Expecting device dev-ttyS0.device... [ 10.661302] systemd[1]: Starting Forward Password Requests to Wall Directory Watch. [ 10.665480] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 10.669216] systemd[1]: Starting Remote File Systems (Pre). [ 10.713277] systemd[1]: Reached target Remote File Systems (Pre). [ 10.717315] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point. [ 10.777290] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point. [ 10.781278] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch. [ 10.785356] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ 10.789204] systemd[1]: Starting Paths. [ 10.821282] systemd[1]: Reached target Paths. [ 10.825220] systemd[1]: Starting Encrypted Volumes. [ 10.861277] systemd[1]: Reached target Encrypted Volumes. [ 10.865229] systemd[1]: Expecting device dev-disk-by\x2duuid-22b43de7\x2d3606\x2d4dc4\x2da551\x2dd33612428f2c.device... [ 10.913297] systemd[1]: Expecting device dev-disk-by\x2duuid-cef0ef1a\x2dc28b\x2d48c7\x2d9485\x2d5f0e54d81dde.device... [ 10.961296] systemd[1]: Expecting device dev-disk-by\x2duuid-6ca962f9\x2dd32c\x2d41ef\x2dbf1a\x2df95409491969.device... [ 11.009299] systemd[1]: Starting Root Slice. [ 11.069315] systemd[1]: Created slice Root Slice. [ 11.097244] systemd[1]: Starting User and Session Slice. [ 11.165308] systemd[1]: Created slice User and Session Slice. [ 11.197247] systemd[1]: Starting /dev/initctl Compatibility Named Pipe. [ 11.277308] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ 11.317248] systemd[1]: Starting Delayed Shutdown Socket. [ 11.389316] systemd[1]: Listening on Delayed Shutdown Socket. [ 11.421280] systemd[1]: Starting Journal Socket (/dev/log). [ 11.493331] systemd[1]: Listening on Journal Socket (/dev/log). [ 11.525272] systemd[1]: Starting Syslog Socket. [ 11.585326] systemd[1]: Listening on Syslog Socket. [ 11.613291] systemd[1]: Starting udev Control Socket. [ 11.677330] systemd[1]: Listening on udev Control Socket. [ 11.709294] systemd[1]: Starting udev Kernel Socket. [ 11.769336] systemd[1]: Listening on udev Kernel Socket. [ 11.797306] systemd[1]: Starting Journal Socket. [ 11.857345] systemd[1]: Listening on Journal Socket. [ 11.885373] systemd[1]: Starting System Slice. [ 11.945363] systemd[1]: Created slice System Slice. [ 11.949361] systemd[1]: Starting File System Check on Root Device... [ 11.991647] systemd[1]: Starting system-systemd\x2dfsck.slice. [ 12.033456] systemd[1]: Created slice system-systemd\x2dfsck.slice. [ 12.037482] systemd[1]: Starting system-getty.slice. [ 12.045748] systemd[1]: Created slice system-getty.slice. [ 12.049379] systemd[1]: Starting system-serial\x2dgetty.slice. [ 12.058036] systemd[1]: Created slice system-serial\x2dgetty.slice. [ 12.061854] systemd[1]: Mounting Debug File System... [ 12.068062] systemd[1]: Starting udev Coldplug all Devices... [ 12.079816] systemd[1]: Started Set Up Additional Binary Formats. [ 12.121497] systemd[1]: Mounting Huge Pages File System... [ 12.167589] systemd[1]: Mounting POSIX Message Queue File System... [ 12.211989] systemd[1]: Starting Create list of required static device nodes for the current kernel... [ 12.265809] systemd[1]: Starting Load Kernel Modules... [ 12.303814] systemd[1]: Starting Journal Service... [ 12.334601] loop: module loaded [ 12.361430] systemd[1]: Started Journal Service. [ 12.862002] EXT4-fs (sda5): re-mounted. Opts: discard,errors=remount-ro [ 13.019434] systemd-udevd[151]: starting version 215 [ 13.073391] random: nonblocking pool is initialized [ 13.248695] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 13.318989] input: PC Speaker as /devices/platform/pcspkr/input/input0 [ 13.579168] ata1.00: configured for UDMA/133 [ 13.581389] ata1: EH complete [ 14.133938] Adding 582652k swap on /dev/sda7. Priority:-1 extents:1 across:582652k SSFS [ 14.513562] EXT4-fs (sda6): mounting with "discard" option, but the device does not support discard [ 14.517380] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: discard [ 14.537641] EXT4-fs (sda1): mounting with "discard" option, but the device does not support discard [ 14.541426] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: discard [ 14.929592] systemd-journald[137]: Received request to flush runtime journal from PID 1 [ 15.010817] NET: Registered protocol family 15 [ 15.074450] sha256_ssse3: Using SSSE3 optimized SHA-256 implementation [ 15.168176] sha512_ssse3: Using SSSE3 optimized SHA-512 implementation [ 15.337790] AVX instructions are not detected. [ 15.465743] AVX instructions are not detected. [ 15.488172] AVX instructions are not detected. [ 15.526773] AVX or AES-NI instructions are not detected. [ 15.530880] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 15.574041] AVX or AES-NI instructions are not detected. [ 15.623013] twofish-x86_64-3way: performance on this CPU would be suboptimal: disabling twofish-x86_64-3way. [ 15.640501] twofish-x86_64-3way: performance on this CPU would be suboptimal: disabling twofish-x86_64-3way. [ 15.921676] ip_tables: (C) 2000-2006 Netfilter Core Team [ 15.948347] nf_conntrack version 0.5.0 (8000 buckets, 32000 max) [ 18.442844] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 18.446082] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready ** Model information not available ** Loaded modules: xt_tcpudp nf_conntrack_ipv4 nf_defrag_ipv4 xt_multiport xt_conntrack nf_conntrack iptable_filter ip_tables x_tables deflate ctr twofish_generic twofish_x86_64 twofish_common camellia_generic camellia_x86_64 serpent_sse2_x86_64 xts serpent_generic lrw gf128mul glue_helper blowfish_generic blowfish_x86_64 blowfish_common cast5_generic cast_common ablk_helper cryptd des_generic cbc cmac xcbc rmd160 sha512_ssse3 sha512_generic sha256_ssse3 sha256_generic hmac crypto_null af_key xfrm_algo i2c_isch evdev ie6xx_wdt i2c_core processor thermal_sys coretemp kvm_intel pcspkr lpc_sch kvm mfd_core shpchp loop autofs4 ext4 crc16 mbcache jbd2 sg sd_mod crc_t10dif crct10dif_generic crct10dif_common ohci_pci ohci_hcd ehci_pci ehci_hcd e1000e ahci libahci libata ptp pps_core scsi_mod usbcore usb_common ** PCI devices: 00:00.0 Host bridge [0600]: Intel Corporation Atom Processor E6xx PCI Host Bridge #1 [8086:4114] (rev 03) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:01.0 Host bridge [0600]: Intel Corporation Atom Processor E6xx Configuration Unit [8086:8183] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 ~ 00:17.0 PCI bridge [0604]: Intel Corporation Atom Processor E6xx PCI Express Port 1 [8086:8184] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=01, subordinate=02, sec-latency=0 I/O behind bridge: 00001000-00001fff Memory behind bridge: a0000000-a0ffffff Prefetchable memory behind bridge: 80000000-800fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v1) Root Port (Slot-), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0 ExtTag- RBE+ DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <1us, L1 <4us ClockPM+ Surprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [90] Subsystem: Device [0000:0000] Capabilities: [a0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: pcieport 00:18.0 PCI bridge [0604]: Intel Corporation Atom Processor E6xx PCI Express Port 2 [8086:8185] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=03, subordinate=07, sec-latency=0 I/O behind bridge: 00002000-00003fff Memory behind bridge: a1000000-a2ffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v1) Root Port (Slot-), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0 ExtTag- RBE+ DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <1us, L1 <4us ClockPM+ Surprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [90] Subsystem: Device [0000:0000] Capabilities: [a0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: pcieport 00:19.0 PCI bridge [0604]: Intel Corporation Atom Processor E6xx PCI Express Port 3 [8086:8180] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=08, subordinate=0c, sec-latency=0 I/O behind bridge: 00004000-00005fff Memory behind bridge: a3000000-a4ffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v1) Root Port (Slot-), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0 ExtTag- RBE+ DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #3, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <1us, L1 <4us ClockPM+ Surprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [90] Subsystem: Device [0000:0000] Capabilities: [a0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: pcieport 00:1a.0 PCI bridge [0604]: Intel Corporation Atom Processor E6xx PCI Express Port 4 [8086:8181] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=0d, subordinate=0d, sec-latency=0 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v1) Root Port (Slot-), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0 ExtTag- RBE+ DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #4, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <1us, L1 <4us ClockPM+ Surprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [90] Subsystem: Device [0000:0000] Capabilities: [a0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: pcieport 00:1f.0 ISA bridge [0601]: Intel Corporation Atom Processor E6xx LPC Bridge [8086:8186] Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Kernel driver in use: lpc_sch 01:00.0 PCI bridge [0604]: Intel Corporation Platform Controller Hub EG20T PCI Express Port [8086:8800] (rev 01) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=01, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 00001000-00001fff Memory behind bridge: a0000000-a0ffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- [virtual] Expansion ROM at 80000000 [disabled] [size=64K] BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0+,D1+,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [70] Express (v2) PCI-Express to PCI/PCI-X Bridge, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0 ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- BrConfRtry- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <512ns, L1 <64us ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-, OBFF Not Supported DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- 02:00.0 Unassigned class [ff00]: Intel Corporation Platform Controller Hub EG20T Packet Hub [8086:8801] (rev 01) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 1: Memory at a0000000 (32-bit, non-prefetchable) [size=2K] Expansion ROM at a0020000 [disabled] [size=128K] Capabilities: [40] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- 02:00.1 Ethernet controller [0200]: Intel Corporation Platform Controller Hub EG20T Gigabit Ethernet Controller [8086:8802] (rev 01) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 10 Region 0: I/O ports at 1000 [size=32] Region 1: Memory at a0000800 (32-bit, non-prefetchable) [size=512] Capabilities: [40] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- 02:00.2 Unassigned class [ff00]: Intel Corporation Platform Controller Hub EG20T General Purpose IO Controller [8086:8803] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 10 Region 1: Memory at a0000a00 (32-bit, non-prefetchable) [size=64] Capabilities: [40] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- 02:02.0 USB controller [0c03]: Intel Corporation Platform Controller Hub EG20T USB OHCI Controller #4 [8086:8804] (rev 01) (prog-if 10 [OHCI]) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 0: Memory at a0000b00 (32-bit, non-prefetchable) [size=256] Capabilities: [40] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ohci-pci 02:02.1 USB controller [0c03]: Intel Corporation Platform Controller Hub EG20T USB OHCI Controller #5 [8086:8805] (rev 01) (prog-if 10 [OHCI]) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 0: Memory at a0000c00 (32-bit, non-prefetchable) [size=256] Capabilities: [40] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ohci-pci 02:02.2 USB controller [0c03]: Intel Corporation Platform Controller Hub EG20T USB OHCI Controller #6 [8086:8806] (rev 01) (prog-if 10 [OHCI]) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 0: Memory at a0000d00 (32-bit, non-prefetchable) [size=256] Capabilities: [40] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ohci-pci 02:02.3 USB controller [0c03]: Intel Corporation Platform Controller Hub EG20T USB2 EHCI Controller #2 [8086:8807] (rev 01) (prog-if 20 [EHCI]) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 0: Memory at a0000e00 (32-bit, non-prefetchable) [size=256] Capabilities: [40] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [a0] Power Management version 0 Flags: PMEClk- DSI- D1- D2- AuxCurrent=220mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Bridge: PM- B3+ Kernel driver in use: ehci-pci 02:02.4 USB controller [0c03]: Intel Corporation Platform Controller Hub EG20T USB Client Controller [8086:8808] (rev 01) (prog-if fe [USB Device]) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 9 Region 1: Memory at a0002000 (32-bit, non-prefetchable) [size=8K] Capabilities: [40] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- 02:04.0 SD Host controller [0805]: Intel Corporation Platform Controller Hub EG20T SDIO Controller #1 [8086:8809] (rev 01) (prog-if 01) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 5 Region 0: Memory at a0004000 (32-bit, non-prefetchable) [size=512] Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [90] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- 02:04.1 SD Host controller [0805]: Intel Corporation Platform Controller Hub EG20T SDIO Controller #2 [8086:880a] (rev 01) (prog-if 01) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 5 Region 0: Memory at a0004200 (32-bit, non-prefetchable) [size=512] Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [90] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- 02:06.0 SATA controller [0106]: Intel Corporation Platform Controller Hub EG20T SATA AHCI Controller [8086:880b] (rev 01) (prog-if 01 [AHCI 1.0]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 40 Region 4: I/O ports at 1020 [size=32] Region 5: Memory at a0004400 (32-bit, non-prefetchable) [size=1K] Expansion ROM at a0040000 [disabled] [size=128K] Capabilities: [40] MSI: Enable+ Count=1/1 Maskable- 64bit- Address: fee0300c Data: 4181 Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [60] SATA HBA v1.0 BAR4 Offset=00000004 Kernel driver in use: ahci 02:08.0 USB controller [0c03]: Intel Corporation Platform Controller Hub EG20T USB OHCI Controller #1 [8086:880c] (rev 01) (prog-if 10 [OHCI]) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at a0004800 (32-bit, non-prefetchable) [size=256] Capabilities: [40] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ohci-pci 02:08.1 USB controller [0c03]: Intel Corporation Platform Controller Hub EG20T USB OHCI Controller #2 [8086:880d] (rev 01) (prog-if 10 [OHCI]) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at a0004900 (32-bit, non-prefetchable) [size=256] Capabilities: [40] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ohci-pci 02:08.2 USB controller [0c03]: Intel Corporation Platform Controller Hub EG20T USB OHCI Controller #3 [8086:880e] (rev 01) (prog-if 10 [OHCI]) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at a0004a00 (32-bit, non-prefetchable) [size=256] Capabilities: [40] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ohci-pci 02:08.3 USB controller [0c03]: Intel Corporation Platform Controller Hub EG20T USB2 EHCI Controller #1 [8086:880f] (rev 01) (prog-if 20 [EHCI]) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at a0004b00 (32-bit, non-prefetchable) [size=256] Capabilities: [40] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [a0] Power Management version 0 Flags: PMEClk- DSI- D1- D2- AuxCurrent=220mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Bridge: PM- B3+ Kernel driver in use: ehci-pci 02:0a.0 Unassigned class [ff00]: Intel Corporation Platform Controller Hub EG20T DMA Controller #1 [8086:8810] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 9 Region 1: Memory at a0004c00 (32-bit, non-prefetchable) [size=256] Capabilities: [40] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [60] #00 [0000] 02:0a.1 Serial controller [0700]: Intel Corporation Platform Controller Hub EG20T UART Controller 0 [8086:8811] (prog-if 02 [16550]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 0: I/O ports at 1040 [size=8] Region 1: Memory at a0004d00 (32-bit, non-prefetchable) [size=16] Capabilities: [40] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: serial 02:0a.2 Serial controller [0700]: Intel Corporation Platform Controller Hub EG20T UART Controller 1 [8086:8812] (prog-if 02 [16550]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 0: I/O ports at 1048 [size=8] Region 1: Memory at a0004d10 (32-bit, non-prefetchable) [size=16] Capabilities: [40] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: serial 02:0a.3 Serial controller [0700]: Intel Corporation Platform Controller Hub EG20T UART Controller 2 [8086:8813] (prog-if 02 [16550]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 0: I/O ports at 1050 [size=8] Region 1: Memory at a0004d20 (32-bit, non-prefetchable) [size=16] Capabilities: [40] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: serial 02:0a.4 Serial controller [0700]: Intel Corporation Platform Controller Hub EG20T UART Controller 3 [8086:8814] (prog-if 02 [16550]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 0: I/O ports at 1058 [size=8] Region 1: Memory at a0004d30 (32-bit, non-prefetchable) [size=16] Capabilities: [40] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: serial 02:0c.0 Unassigned class [ff00]: Intel Corporation Platform Controller Hub EG20T DMA Controller #2 [8086:8815] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 5 Region 1: Memory at a0004e00 (32-bit, non-prefetchable) [size=256] Capabilities: [40] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [60] #00 [0000] 02:0c.1 Serial bus controller [0c80]: Intel Corporation Platform Controller Hub EG20T Serial Peripheral Interface Bus [8086:8816] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 5 Region 1: Memory at a0004f00 (32-bit, non-prefetchable) [size=32] Capabilities: [40] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- 02:0c.2 Serial bus controller [0c80]: Intel Corporation Platform Controller Hub EG20T I2C Controller [8086:8817] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 5 Region 1: Memory at a0005000 (32-bit, non-prefetchable) [size=256] Capabilities: [40] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- 02:0c.3 CANBUS [0c09]: Intel Corporation Platform Controller Hub EG20T Controller Area Network (CAN) Controller [8086:8818] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 5 Region 1: Memory at a0005200 (32-bit, non-prefetchable) [size=512] Capabilities: [40] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- 02:0c.4 Unassigned class [ff00]: Intel Corporation Platform Controller Hub EG20T IEEE 1588 Hardware Assist [8086:8819] (rev 01) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 5 Region 1: Memory at a0005400 (32-bit, non-prefetchable) [size=256] Capabilities: [40] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- 03:00.0 PCI bridge [0604]: Integrated Device Technology, Inc. [IDT] PES4T4 PCI Express Switch [111d:803a] (rev 0e) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=03, secondary=04, subordinate=07, sec-latency=0 I/O behind bridge: 00002000-00003fff Memory behind bridge: a1000000-a2ffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v1) Upstream Port, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0 ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ SlotPowerLimit 0.000W DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <2us, L1 <4us ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; Disabled- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [c0] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: pcieport 04:02.0 PCI bridge [0604]: Integrated Device Technology, Inc. [IDT] PES4T4 PCI Express Switch [111d:803a] (rev 0e) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=04, secondary=05, subordinate=05, sec-latency=0 I/O behind bridge: 00002000-00002fff Memory behind bridge: a1000000-a1ffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v1) Downstream Port (Slot-), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0 ExtTag+ RBE+ DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend- LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <2us, L1 <4us ClockPM- Surprise+ LLActRep+ BwNot- LnkCtl: ASPM Disabled; Disabled- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- Capabilities: [c0] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Kernel driver in use: pcieport 04:03.0 PCI bridge [0604]: Integrated Device Technology, Inc. [IDT] PES4T4 PCI Express Switch [111d:803a] (rev 0e) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=04, secondary=06, subordinate=06, sec-latency=0 I/O behind bridge: 00003000-00003fff Memory behind bridge: a2000000-a2ffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v1) Downstream Port (Slot-), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0 ExtTag+ RBE+ DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend- LnkCap: Port #3, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <2us, L1 <4us ClockPM- Surprise+ LLActRep+ BwNot- LnkCtl: ASPM Disabled; Disabled- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- Capabilities: [c0] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Kernel driver in use: pcieport 04:04.0 PCI bridge [0604]: Integrated Device Technology, Inc. [IDT] PES4T4 PCI Express Switch [111d:803a] (rev 0e) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=04, secondary=07, subordinate=07, sec-latency=0 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v1) Downstream Port (Slot-), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0 ExtTag+ RBE+ DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend- LnkCap: Port #4, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <2us, L1 <4us ClockPM- Surprise+ LLActRep+ BwNot- LnkCtl: ASPM Disabled; Disabled- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [c0] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Kernel driver in use: pcieport 05:00.0 Ethernet controller [0200]: Intel Corporation 82574L Gigabit Network Connection [8086:10d3] Subsystem: Intel Corporation Device [8086:0000] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 19 Region 0: Memory at a1000000 (32-bit, non-prefetchable) [size=128K] Region 2: I/O ports at 2000 [size=32] Region 3: Memory at a1020000 (32-bit, non-prefetchable) [size=16K] Capabilities: [c8] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME- Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [e0] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <128ns, L1 <64us ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [a0] MSI-X: Enable+ Count=5 Masked- Vector table: BAR=3 offset=00000000 PBA: BAR=3 offset=00002000 Kernel driver in use: e1000e 06:00.0 Ethernet controller [0200]: Intel Corporation 82574L Gigabit Network Connection [8086:10d3] Subsystem: Intel Corporation Device [8086:0000] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at a2000000 (32-bit, non-prefetchable) [size=128K] Region 2: I/O ports at 3000 [size=32] Region 3: Memory at a2020000 (32-bit, non-prefetchable) [size=16K] Capabilities: [c8] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME- Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [e0] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #3, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <128ns, L1 <64us ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [a0] MSI-X: Enable+ Count=5 Masked- Vector table: BAR=3 offset=00000000 PBA: BAR=3 offset=00002000 Kernel driver in use: e1000e 08:00.0 PCI bridge [0604]: Integrated Device Technology, Inc. [IDT] PES4T4 PCI Express Switch [111d:803a] (rev 0e) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=08, secondary=09, subordinate=0c, sec-latency=0 I/O behind bridge: 00004000-00005fff Memory behind bridge: a3000000-a4ffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v1) Upstream Port, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0 ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ SlotPowerLimit 0.000W DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <2us, L1 <4us ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; Disabled- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [c0] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: pcieport 09:02.0 PCI bridge [0604]: Integrated Device Technology, Inc. [IDT] PES4T4 PCI Express Switch [111d:803a] (rev 0e) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=09, secondary=0a, subordinate=0a, sec-latency=0 I/O behind bridge: 00004000-00004fff Memory behind bridge: a3000000-a3ffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v1) Downstream Port (Slot-), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0 ExtTag+ RBE+ DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend- LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <2us, L1 <4us ClockPM- Surprise+ LLActRep+ BwNot- LnkCtl: ASPM Disabled; Disabled- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- Capabilities: [c0] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Kernel driver in use: pcieport 09:03.0 PCI bridge [0604]: Integrated Device Technology, Inc. [IDT] PES4T4 PCI Express Switch [111d:803a] (rev 0e) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=09, secondary=0b, subordinate=0b, sec-latency=0 I/O behind bridge: 00005000-00005fff Memory behind bridge: a4000000-a4ffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v1) Downstream Port (Slot-), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0 ExtTag+ RBE+ DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend- LnkCap: Port #3, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <2us, L1 <4us ClockPM- Surprise+ LLActRep+ BwNot- LnkCtl: ASPM Disabled; Disabled- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- Capabilities: [c0] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Kernel driver in use: pcieport 09:04.0 PCI bridge [0604]: Integrated Device Technology, Inc. [IDT] PES4T4 PCI Express Switch [111d:803a] (rev 0e) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=09, secondary=0c, subordinate=0c, sec-latency=0 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v1) Downstream Port (Slot-), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0 ExtTag+ RBE+ DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend- LnkCap: Port #4, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <2us, L1 <4us ClockPM- Surprise+ LLActRep+ BwNot- LnkCtl: ASPM Disabled; Disabled- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [c0] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Kernel driver in use: pcieport 0a:00.0 Ethernet controller [0200]: Intel Corporation 82574L Gigabit Network Connection [8086:10d3] Subsystem: Intel Corporation Device [8086:0000] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at a3000000 (32-bit, non-prefetchable) [size=128K] Region 2: I/O ports at 4000 [size=32] Region 3: Memory at a3020000 (32-bit, non-prefetchable) [size=16K] Capabilities: [c8] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME- Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [e0] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <128ns, L1 <64us ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [a0] MSI-X: Enable+ Count=5 Masked- Vector table: BAR=3 offset=00000000 PBA: BAR=3 offset=00002000 Kernel driver in use: e1000e 0b:00.0 Ethernet controller [0200]: Intel Corporation 82574L Gigabit Network Connection [8086:10d3] Subsystem: Intel Corporation Device [8086:0000] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 17 Region 0: Memory at a4000000 (32-bit, non-prefetchable) [size=128K] Region 2: I/O ports at 5000 [size=32] Region 3: Memory at a4020000 (32-bit, non-prefetchable) [size=16K] Capabilities: [c8] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME- Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [e0] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #3, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <128ns, L1 <64us ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [a0] MSI-X: Enable+ Count=5 Masked- Vector table: BAR=3 offset=00000000 PBA: BAR=3 offset=00002000 Kernel driver in use: e1000e ** USB devices: Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub -- System Information: Debian Release: 8.0 APT prefers testing APT policy: (500, 'testing'), (500, 'stable') Architecture: amd64 (x86_64) Kernel: Linux 3.16.0-4-amd64 (SMP w/2 CPU cores) Locale: LANG=C, LC_CTYPE=C (charmap=ANSI_X3.4-1968) Shell: /bin/sh linked to /bin/dash Init: systemd (via /run/systemd/system) Versions of packages linux-image-3.16.0-4-amd64 depends on: ii debconf [debconf-2.0] 1.5.54 ii initramfs-tools [linux-initramfs-tool] 0.116 ii kmod 18-3 ii linux-base 3.5 ii module-init-tools 18-3 Versions of packages linux-image-3.16.0-4-amd64 recommends: ii firmware-linux-free 3.3 ii irqbalance 1.0.6-3 Versions of packages linux-image-3.16.0-4-amd64 suggests: pn debian-kernel-handbook <none> ii grub-pc 2.02~beta2-17 pn linux-doc-3.16 <none> Versions of packages linux-image-3.16.0-4-amd64 is related to: pn firmware-atheros <none> pn firmware-bnx2 <none> pn firmware-bnx2x <none> pn firmware-brcm80211 <none> pn firmware-intelwimax <none> pn firmware-ipw2x00 <none> pn firmware-ivtv <none> pn firmware-iwlwifi <none> pn firmware-libertas <none> pn firmware-linux <none> pn firmware-linux-nonfree <none> pn firmware-myricom <none> pn firmware-netxen <none> pn firmware-qlogic <none> pn firmware-ralink <none> pn firmware-realtek <none> pn xen-hypervisor <none> -- debconf information excluded
smime.p7s
Description: S/MIME Cryptographic Signature
