Package: src:linux Version: 3.16~rc6-1~exp1 Severity: normal With linux-image-3.15-trunk-armmp 3.15.5-1~exp1 which included patches applied from upstream, HDMI video output worked for me on both the Cubox i4pro and Wandboard Quad. The console framebuffer showed output, X with fbdev worked...
Now with 3.16~rc6-1~exp1, which shold have the applied patches, there's no output. Perhaps other additional patches caused issues. I also tested with 3.16~rc5-1~exp1, no luck. hrm. Thanks for working on Debian kernel packaging! live well, vagrant -- Package-specific info: ** Version: Linux version 3.16-rc6-armmp (debian-kernel@lists.debian.org) (gcc version 4.8.3 (Debian 4.8.3-5) ) #1 SMP Debian 3.16~rc6-1~exp1 (2014-07-21) ** Command line: console=ttymxc0,115200 ** Tainted: C (1024) * Module from drivers/staging has been loaded. ** Kernel log: [ 1.384242] mmc0: new high speed SDHC card at address 1234 [ 1.390289] mmcblk0: mmc0:1234 SA04G 3.63 GiB [ 1.398676] mmcblk0: p1 p2 p3 < p5 > [ 1.802878] PM: Starting manual resume from disk [ 1.807583] PM: Hibernation image partition 179:5 present [ 1.807592] PM: Looking for hibernation image. [ 1.809096] PM: Image not found (code -22) [ 1.809106] PM: Hibernation image not present or could not be loaded. [ 1.860617] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 3.002967] systemd-udevd[260]: starting version 208 [ 3.354410] Registered IR keymap rc-empty [ 3.359051] input: gpio_ir_recv as /devices/soc0/ir-receiver/rc/rc0/input0 [ 3.366521] rc0: gpio_ir_recv as /devices/soc0/ir-receiver/rc/rc0 [ 3.374681] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) [ 3.398170] i2c i2c-1: IMX I2C adapter registered [ 3.413338] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.453949] [drm] Initialized drm 1.1.0 20060810 [ 3.459654] SCSI subsystem initialized [ 3.484164] i2c i2c-2: IMX I2C adapter registered [ 3.511686] libata version 3.00 loaded. [ 3.542674] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled [ 3.549529] imxdrm: module is from the staging directory, the quality is unknown, you have been warned. [ 3.549534] imxdrm: module is from the staging directory, the quality is unknown, you have been warned. [ 3.556139] IR Sony protocol handler initialized [ 3.556148] IR SANYO protocol handler initialized [ 3.562674] lirc_dev: IR Remote Control driver registered, major 243 [ 3.568302] rc rc0: lirc_dev: driver ir-lirc-codec (gpio-rc-recv) registered at minor = 0 [ 3.568306] IR LIRC bridge handler initialized [ 3.574839] IR NEC protocol handler initialized [ 3.579150] IR JVC protocol handler initialized [ 3.584020] input: MCE IR Keyboard/Mouse (gpio-rc-recv) as /devices/virtual/input/input1 [ 3.584623] IR MCE Keyboard/mouse protocol handler initialized [ 3.587476] imx_hdmi: module is from the staging directory, the quality is unknown, you have been warned. [ 3.592797] ci_hdrc ci_hdrc.0: ChipIdea HDRC found, lpm: 0; cap: f00c6100 op: f00c6140 [ 3.597022] ci_hdrc ci_hdrc.0: It is OTG capable controller [ 3.597522] ci_hdrc ci_hdrc.0: EHCI Host Controller [ 3.597781] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 [ 3.606796] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 [ 3.607067] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.607074] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.607082] usb usb1: Product: EHCI Host Controller [ 3.607087] usb usb1: Manufacturer: Linux 3.16-rc6-armmp ehci_hcd [ 3.607092] usb usb1: SerialNumber: ci_hdrc.0 [ 3.607779] hub 1-0:1.0: USB hub found [ 3.607818] hub 1-0:1.0: 1 port detected [ 3.608715] ci_hdrc ci_hdrc.1: ChipIdea HDRC found, lpm: 0; cap: f00ee300 op: f00ee340 [ 3.611702] ci_hdrc ci_hdrc.1: doesn't support gadget [ 3.611712] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 3.611956] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2 [ 3.622801] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 3.623048] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.623056] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.623062] usb usb2: Product: EHCI Host Controller [ 3.623069] usb usb2: Manufacturer: Linux 3.16-rc6-armmp ehci_hcd [ 3.623074] usb usb2: SerialNumber: ci_hdrc.1 [ 3.623758] hub 2-0:1.0: USB hub found [ 3.623801] hub 2-0:1.0: 1 port detected [ 3.651967] imx-spdif sound-spdif: ASoC: CPU DAI (null) not registered [ 3.651998] imx-spdif sound-spdif: snd_soc_register_card failed: -517 [ 3.652015] platform sound-spdif: Driver imx-spdif requests probe deferral [ 3.666015] imx-spdif sound-spdif: snd-soc-dummy-dai <-> 2004000.spdif mapping ok [ 3.770603] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 3.771291] IR RC5(x) protocol handler initialized [ 3.775570] IR RC6 protocol handler initialized [ 3.788776] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 3.799418] scsi0 : ahci_platform [ 3.803185] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 71 [ 3.918823] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 4.055479] usb 1-1: New USB device found, idVendor=1a40, idProduct=0201 [ 4.062216] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 4.069394] usb 1-1: Product: USB 2.0 Hub [MTT] [ 4.074866] hub 1-1:1.0: USB hub found [ 4.078730] hub 1-1:1.0: 7 ports detected [ 4.130789] ata1: SATA link down (SStatus 0 SControl 300) [ 4.136249] ahci-imx 2200000.sata: no device found, disabling link. [ 4.142540] ahci-imx 2200000.sata: pass .hotplug=1 to enable hotplug [ 4.354978] usb 1-1.1: new low-speed USB device number 3 using ci_hdrc [ 4.469974] usb 1-1.1: New USB device found, idVendor=413c, idProduct=2105 [ 4.476882] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 4.484230] usb 1-1.1: Product: Dell USB Keyboard [ 4.488954] usb 1-1.1: Manufacturer: Dell [ 4.498508] random: nonblocking pool is initialized [ 4.533702] input: Dell Dell USB Keyboard as /devices/soc0/soc/2100000.aips-bus/2184000.usb/ci_hdrc.0/usb1/1-1/1-1.1/1-1.1:1.0/0003:413C:2105.0001/input/input2 [ 4.548463] hid-generic 0003:413C:2105.0001: input,hidraw0: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-ci_hdrc.0-1.1/input0 [ 34.887534] Adding 218108k swap on /dev/mmcblk0p5. Priority:-1 extents:1 across:218108k SS [ 34.984350] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) [ 35.391424] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro [ 38.392921] EXT4-fs (mmcblk0p1): mounting ext2 file system using the ext4 subsystem [ 38.552251] EXT4-fs (mmcblk0p1): mounted filesystem without journal. Opts: (null) [ 41.935413] RPC: Registered named UNIX socket transport module. [ 41.941380] RPC: Registered udp transport module. [ 41.946123] RPC: Registered tcp transport module. [ 41.950846] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 41.971518] fec 2188000.ethernet eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=2188000.ethernet:04, irq=-1) [ 41.983229] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 42.018096] FS-Cache: Loaded [ 42.067499] FS-Cache: Netfs 'nfs' registered for caching [ 42.128983] Installing knfsd (copyright (C) 1996 o...@monad.swb.de). [ 45.971264] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 45.979000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready ** Model information Hardware : Freescale i.MX6 Quad/DualLite (Device Tree) Revision : 0000 ** Loaded modules: nfsd auth_rpcgss oid_registry nfs_acl nfs lockd fscache sunrpc hid_generic ir_rc6_decoder ir_rc5_decoder snd_soc_fsl_spdif imx_pcm_dma snd_soc_imx_spdif snd_soc_core ci_hdrc_imx imx_hdmi(C) ir_mce_kbd_decoder ir_jvc_decoder ir_nec_decoder ir_lirc_codec lirc_dev ir_sony_decoder ir_sanyo_decoder imxdrm(C) snd_compress ahci_imx libahci_platform libahci libata evdev drm_kms_helper ci_hdrc scsi_mod drm snd_pcm_dmaengine ehci_hcd usbmisc_imx i2c_imx snd_pcm imx2_wdt phy_mxs_usb pwm_imx snd_timer gpio_ir_recv snd soundcore ext4 crc16 mbcache jbd2 sdhci_esdhc_imx sdhci_pltfm sdhci ** PCI devices: ** USB devices: Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 413c:2105 Dell Computer Corp. Model L100 Keyboard Bus 001 Device 002: ID 1a40:0201 Terminus Technology Inc. FE 2.1 7-port Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub -- System Information: Debian Release: jessie/sid APT prefers testing-updates APT policy: (500, 'testing-updates'), (500, 'testing'), (120, 'unstable'), (1, 'experimental') Architecture: armhf (armv7l) Kernel: Linux 3.16-rc6-armmp (SMP w/4 CPU cores) Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash Versions of packages linux-image-3.16-rc6-armmp depends on: ii debconf [debconf-2.0] 1.5.53 ii initramfs-tools [linux-initramfs-tool] 0.115 ii kmod 18-1 ii linux-base 3.5 Versions of packages linux-image-3.16-rc6-armmp recommends: ii firmware-linux-free 3.3 Versions of packages linux-image-3.16-rc6-armmp suggests: pn debian-kernel-handbook <none> pn fdutils <none> pn linux-doc-3.16 <none> Versions of packages linux-image-3.16-rc6-armmp is related to: pn firmware-atheros <none> pn firmware-bnx2 <none> pn firmware-bnx2x <none> pn firmware-brcm80211 <none> pn firmware-intelwimax <none> pn firmware-ipw2x00 <none> pn firmware-ivtv <none> pn firmware-iwlwifi <none> pn firmware-libertas <none> pn firmware-linux <none> pn firmware-linux-nonfree <none> pn firmware-myricom <none> pn firmware-netxen <none> pn firmware-qlogic <none> pn firmware-ralink <none> pn firmware-realtek <none> pn xen-hypervisor <none> -- debconf information: linux-image-3.16-rc6-armmp/postinst/mips-initrd-3.16-rc6-armmp: linux-image-3.16-rc6-armmp/prerm/removing-running-kernel-3.16-rc6-armmp: true linux-image-3.16-rc6-armmp/postinst/depmod-error-initrd-3.16-rc6-armmp: false
signature.asc
Description: Digital signature
