Package: src:linux
Version: 3.2.54-2
Severity: important
File: /lib/modules/3.2.0-4-amd64/kernel/drivers/net/wireless/iwlwifi/iwlwifi.ko
I am using a HP EliteBook Folio 9470m laptop.
When my wireless is on, if I plug in the ethernet cable, I get a message:
"iwlwifi 0000:03:00.0: RF_KILL bit toggled to disable radio",
causing the wireless to stop working.
I wanted to use the wired network for internet communication and the
wireless to act as a local wifi hot spot, which fails due to the wireless
problem.
This happens even when ethernet interface (eth0) is not up.
I ran 'rfkill status', which showed:
2: hp-wifi: Wireless LAN
Soft blocked: no
Hard blocked: no
3: hp-bluetooth: Bluetooth
Soft blocked: no
Hard blocked: no
10: phy3: Wireless LAN
Soft blocked: no
Hard blocked: yes
14: hci0: Bluetooth
Soft blocked: no
Hard blocked: no
The above happens any time when ethernet wire is connected, and the 'wireless
LED'
changes color from White to Yellow, indicating inactive status.
I tried switching off the hardware switch, and then ran 'rfkill status', which
showed
'Hard Blocked: yes' for all the interfaces (as expected).
When I again pressed the wireless button (toggle switch), the above message
repeated.
However, after disconnecting the ethernet cable, I get a message:
"iwlwifi 0000:03:00.0: RF_KILL bit toggled to enable radio".
Running 'rfkill status' shows 'Hard blocked: no' for all the above wireless
devices and the
wireless works. I first thought that Change of 'Hard blocked:' from 'no' to
'yes' after insertion of ethernet cable could suggest the hardware to change
state.
However, connection of ethernet cable to any laptop cannot trip the wireless
switch.
Therefore, I believe, connection of ethernet cable makes 'iwlwifi' to switch
off the wireless
network as a software bug, and am filling a bug report for rectification.
Note that the problem repeats with newer kernel version '3.12.9-1~bpo70+1'.
-- Package-specific info:
** Version:
Linux version 3.2.0-4-amd64 (debian-kernel@lists.debian.org) (gcc version 4.6.3
(Debian 4.6.3-14) ) #1 SMP Debian 3.2.54-2
** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.2.0-4-amd64
root=UUID=ed6e1b76-afca-4d44-8b92-4b93f837f41c ro acpi_osi=
acpi_backlight=vendor verbose resume=/dev/sda4
** Tainted: WO (4608)
* Taint on warning.
* Out-of-tree module has been loaded.
** Kernel log:
[ 4131.063385] PM: resume of devices complete after 1475.107 msecs
[ 4131.122683] PM: Finishing wakeup.
[ 4131.122685] Restarting tasks ... done.
[ 4131.125675] video LNXVIDEO:01: Restoring backlight state
[ 4131.194449] usb 2-1.8: new full-speed USB device number 10 using ehci_hcd
[ 4131.210697] hub 2-1:1.0: unable to enumerate USB device on port 8
[ 4131.362240] [drm:pch_irq_handler] *ERROR* PCH poison interrupt
[ 4132.710375] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control:
None
[ 4134.444772] iwlwifi 0000:03:00.0: RF_KILL bit toggled to disable radio.
[ 4225.230251] thinkpad_ec: no ThinkPad embedded controller!
[ 4310.894903] PM: Syncing filesystems ... done.
[ 4310.912276] PM: Preparing system for mem sleep
[ 4311.108021] Freezing user space processes ... (elapsed 0.01 seconds) done.
[ 4311.123381] Freezing remaining freezable tasks ... (elapsed 0.01 seconds)
done.
[ 4311.139406] PM: Entering mem sleep
[ 4311.139430] Suspending console(s) (use no_console_suspend to debug)
[ 4311.139826] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 4311.140994] sd 0:0:0:0: [sda] Stopping disk
[ 4311.429116] snd_hda_intel 0000:00:1b.0: power state changed by ACPI to D3
[ 4311.522762] e1000e 0000:00:19.0: wake-up capability enabled by ACPI
[ 4311.834612] PM: suspend of devices complete after 695.863 msecs
[ 4311.850725] ehci_hcd 0000:00:1d.0: wake-up capability enabled by ACPI
[ 4311.866681] ehci_hcd 0000:00:1a.0: wake-up capability enabled by ACPI
[ 4311.882566] xhci_hcd 0000:00:14.0: wake-up capability enabled by ACPI
[ 4311.898505] PM: late suspend of devices complete after 63.956 msecs
[ 4311.898819] ACPI: Preparing to enter system sleep state S3
[ 4311.919099] PM: Saving platform NVS memory
[ 4311.919439] Disabling non-boot CPUs ...
[ 4312.022332] CPU 1 is now offline
[ 4312.126216] CPU 2 is now offline
[ 4312.230102] CPU 3 is now offline
[ 4312.230559] Extended CMOS year: 2000
[ 4312.230845] ACPI: Low-level resume complete
[ 4312.230893] PM: Restoring platform NVS memory
[ 4312.231202] Extended CMOS year: 2000
[ 4312.231244] Enabling non-boot CPUs ...
[ 4312.231410] Booting Node 0 Processor 1 APIC 0x1
[ 4312.231412] smpboot cpu 1: start_ip = 98000
[ 4312.242430] Calibrating delay loop (skipped) already calibrated this CPU
[ 4312.263405] NMI watchdog enabled, takes one hw-pmu counter.
[ 4312.263750] CPU1 is up
[ 4312.263949] Booting Node 0 Processor 2 APIC 0x2
[ 4312.263951] smpboot cpu 2: start_ip = 98000
[ 4312.274967] Calibrating delay loop (skipped) already calibrated this CPU
[ 4312.295949] NMI watchdog enabled, takes one hw-pmu counter.
[ 4312.296329] CPU2 is up
[ 4312.296583] Booting Node 0 Processor 3 APIC 0x3
[ 4312.296585] smpboot cpu 3: start_ip = 98000
[ 4312.307602] Calibrating delay loop (skipped) already calibrated this CPU
[ 4312.328929] NMI watchdog enabled, takes one hw-pmu counter.
[ 4312.329325] CPU3 is up
[ 4312.333498] ACPI: Waking up from system sleep state S3
[ 4313.137994] xhci_hcd 0000:00:14.0: wake-up capability disabled by ACPI
[ 4313.138119] ehci_hcd 0000:00:1a.0: wake-up capability disabled by ACPI
[ 4313.138354] ehci_hcd 0000:00:1d.0: wake-up capability disabled by ACPI
[ 4313.139226] PM: early resume of devices complete after 1.337 msecs
[ 4313.139375] i915 0000:00:02.0: setting latency timer to 64
[ 4313.139388] xhci_hcd 0000:00:14.0: setting latency timer to 64
[ 4313.139399] e1000e 0000:00:19.0: wake-up capability disabled by ACPI
[ 4313.139474] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[ 4313.139499] ehci_hcd 0000:00:1d.0: setting latency timer to 64
[ 4313.139502] e1000e 0000:00:19.0: irq 40 for MSI/MSI-X
[ 4313.139510] ahci 0000:00:1f.2: setting latency timer to 64
[ 4313.139587] sdhci-pci 0000:02:00.0: setting latency timer to 64
[ 4313.139669] iwlwifi 0000:03:00.0: RF_KILL bit toggled to enable radio.
[ 4313.139861] sd 0:0:0:0: [sda] Starting disk
[ 4313.151915] snd_hda_intel 0000:00:1b.0: power state changed by ACPI to D0
[ 4313.151923] snd_hda_intel 0000:00:1b.0: power state changed by ACPI to D0
[ 4313.151930] snd_hda_intel 0000:00:1b.0: power state changed by ACPI to D0
[ 4313.151934] snd_hda_intel 0000:00:1b.0: power state changed by ACPI to D0
[ 4313.151944] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[ 4313.151981] snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X
[ 4313.184622] [drm] Enabling RC6 states: RC6 on, RC6p on, RC6pp off
[ 4313.461563] usb 3-2: reset low-speed USB device number 3 using xhci_hcd
[ 4313.465374] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 4313.465866] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device
(Stat=0x51 Err=0x04)
[ 4313.465871] ata1.00: supports DRM functions and may not be fully accessible
[ 4313.466489] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device
(Stat=0x51 Err=0x04)
[ 4313.466494] ata1.00: supports DRM functions and may not be fully accessible
[ 4313.466604] ata1.00: configured for UDMA/100
[ 4313.480929] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with
disabled ep ffff88013927c980
[ 4313.480937] usb 3-2: ep 0x81 - rounding interval to 64 microframes, ep desc
says 80 microframes
[ 4313.549523] usb 2-1.6: reset full-speed USB device number 7 using ehci_hcd
[ 4313.644290] btusb 2-1.6:1.0: no reset_resume for driver btusb?
[ 4313.644294] btusb 2-1.6:1.1: no reset_resume for driver btusb?
[ 4313.713298] usb 1-1.3: reset high-speed USB device number 4 using ehci_hcd
[ 4314.550170] Extended CMOS year: 2000
[ 4314.572525] PM: resume of devices complete after 1434.857 msecs
[ 4314.666636] PM: Finishing wakeup.
[ 4314.666638] Restarting tasks ... done.
[ 4314.668435] video LNXVIDEO:01: Restoring backlight state
[ 4314.739977] usb 2-1.8: new full-speed USB device number 11 using ehci_hcd
[ 4314.757151] hub 2-1:1.0: unable to enumerate USB device on port 8
[ 4314.903870] [drm:pch_irq_handler] *ERROR* PCH poison interrupt
[ 4316.251915] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control:
None
[ 4318.006108] iwlwifi 0000:03:00.0: RF_KILL bit toggled to disable radio.
[ 5721.132030] hp_wmi: Unknown event_id - 8 - 0x2
[ 5723.202935] hp_wmi: Unknown event_id - 8 - 0x1
[ 5734.732667] hp_wmi: Unknown event_id - 8 - 0x2
[ 5736.063998] hp_wmi: Unknown event_id - 8 - 0x1
** Model information
sys_vendor: Hewlett-Packard
product_name: HP EliteBook Folio 9470m
product_version: A1029D1103
chassis_vendor: Hewlett-Packard
chassis_version:
bios_vendor: Hewlett-Packard
bios_version: 68IBD Ver. F.32
board_vendor: Hewlett-Packard
board_name: 18DF
board_version: KBC Version 62.14
** Loaded modules:
nls_utf8
nls_cp437
vfat
fat
usb_storage
usbhid
hid
iwlwifi
acpi_cpufreq
cpufreq_stats
cpufreq_userspace
cpufreq_conservative
cpufreq_powersave
uinput
deflate
ctr
twofish_generic
twofish_x86_64_3way
twofish_x86_64
twofish_common
camellia
serpent
blowfish_generic
blowfish_x86_64
blowfish_common
cast5
des_generic
cbc
xcbc
rmd160
sha512_generic
sha256_generic
sha1_ssse3
sha1_generic
hmac
crypto_null
af_key
fuse
nfsd
nfs
nfs_acl
auth_rpcgss
fscache
lockd
sunrpc
hwmon_vid
dm_crypt
dm_mod
snd_hda_codec_hdmi
snd_hda_codec_idt
joydev
tpm_infineon
snd_hda_intel
snd_hda_codec
arc4
snd_hwdep
snd_pcm_oss
snd_mixer_oss
snd_pcm
snd_page_alloc
snd_seq_midi
snd_seq_midi_event
snd_rawmidi
snd_seq
snd_seq_device
snd_timer
mac80211
hp_wmi
sparse_keymap
coretemp
crc32c_intel
i915
uvcvideo
snd
videodev
cfg80211
tpm_tis
hp_accel
tpm
v4l2_compat_ioctl32
drm_kms_helper
iTCO_wdt
lis3lv02d
ghash_clmulni_intel
btusb
aesni_intel
media
bluetooth
aes_x86_64
aes_generic
cryptd
iTCO_vendor_support
evdev
psmouse
rfkill
pcspkr
serio_raw
i2c_i801
soundcore
container
tpm_bios
wmi
input_polldev
drm
battery
i2c_algo_bit
video
i2c_core
mperf
ac
power_supply
button
processor
ext4
crc16
jbd2
mbcache
btrfs
crc32c
libcrc32c
zlib_deflate
sg
sd_mod
crc_t10dif
ahci
libahci
xhci_hcd
libata
thermal
ehci_hcd
thermal_sys
scsi_mod
e1000e
usbcore
sdhci_pci
sdhci
mmc_core
usb_common
** Network interface configuration:
auto lo
iface lo inet loopback
auto eth0
iface eth0 inet static
address 192.168.123.74
netmask 255.255.255.0
network 192.168.123.0
broadcast 192.168.101.255
gateway 192.168.123.1
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP
qlen 1000
link/ether 00:1f:29:83:83:4e brd ff:ff:ff:ff:ff:ff
inet 192.168.123.74/24 brd 192.168.101.255 scope global eth0
inet6 fe80::21f:29ff:fe83:834e/64 scope link
valid_lft forever preferred_lft forever
6: wlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
link/ether c8:f7:33:ba:4c:e4 brd ff:ff:ff:ff:ff:ff
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes
packets errs drop fifo colls carrier compressed
lo: 630 8 0 0 0 0 0 0 630
8 0 0 0 0 0 0
wlan0: 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0
eth0: 27388407 28844 0 10 0 0 0 224 2452434
19104 0 0 0 0 0 0
*** Protocol statistics:
Ip:
24711 total packets received
17 with invalid addresses
0 forwarded
0 incoming packets discarded
24694 incoming packets delivered
19059 requests sent out
338 dropped because of missing route
Icmp:
27 ICMP messages received
17 input ICMP message failed.
ICMP input histogram:
destination unreachable: 24
echo replies: 3
34 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
destination unreachable: 28
echo request: 6
IcmpMsg:
InType0: 3
InType3: 24
OutType3: 28
OutType8: 6
Tcp:
588 active connections openings
0 passive connection openings
4 failed connection attempts
5 connection resets received
1 connections established
22586 segments received
17914 segments send out
65 segments retransmited
14 bad segments received.
178 resets sent
Udp:
1045 packets received
26 packets to unknown port received.
0 packet receive errors
1073 packets sent
UdpLite:
TcpExt:
334 TCP sockets finished time wait in fast timer
1 packets rejects in established connections because of timestamp
426 delayed acks sent
Quick ack mode was activated 109 times
2 packets directly queued to recvmsg prequeue.
2 bytes directly received in process context from prequeue
16834 packet headers predicted
1007 acknowledgments not containing data payload received
838 predicted acknowledgments
1 congestion windows recovered without slow start by DSACK
32 congestion windows recovered without slow start after partial ack
42 other TCP timeouts
86 DSACKs sent for old packets
21 DSACKs received
39 connections reset due to unexpected data
5 connections reset due to early user close
4 connections aborted due to timeout
TCPDSACKIgnoredNoUndo: 3
TCPSackShiftFallback: 5
TCPChallengeACK: 14
TCPSYNChallenge: 14
IpExt:
InMcastPkts: 2
InBcastPkts: 1008
InOctets: 26658426
OutOctets: 2097088
InMcastOctets: 64
InBcastOctets: 99832
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 3rd Gen Core processor DRAM
Controller [8086:0154] (rev 09)
Subsystem: Hewlett-Packard Company Device [103c:18df]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation 3rd Gen Core
processor Graphics Controller [8086:0166] (rev 09) (prog-if 00 [VGA controller])
Subsystem: Hewlett-Packard Company Device [103c:18df]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 44
Region 0: Memory at d0000000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 2000 [size=64]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:14.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset
Family USB xHCI Host Controller [8086:1e31] (rev 04) (prog-if 30 [XHCI])
Subsystem: Hewlett-Packard Company Device [103c:18df]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 41
Region 0: Memory at d0720000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
00:16.0 Communication controller [0780]: Intel Corporation 7 Series/C210 Series
Chipset Family MEI Controller #1 [8086:1e3a] (rev 04)
Subsystem: Hewlett-Packard Company Device [103c:18df]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx+
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 0: Memory at d0735000 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
00:19.0 Ethernet controller [0200]: Intel Corporation 82579LM Gigabit Network
Connection [8086:1502] (rev 04)
Subsystem: Hewlett-Packard Company Device [103c:18df]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 40
Region 0: Memory at d0700000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at d073b000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at 2080 [size=32]
Capabilities: <access denied>
Kernel driver in use: e1000e
00:1a.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset
Family USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Device [103c:18df]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d073a000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1b.0 Audio device [0403]: Intel Corporation 7 Series/C210 Series Chipset
Family High Definition Audio Controller [8086:1e20] (rev 04)
Subsystem: Hewlett-Packard Company Device [103c:18df]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 45
Region 0: Memory at d0730000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset
Family PCI Express Root Port 1 [8086:1e10] (rev c4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: d0600000-d06fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.2 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset
Family PCI Express Root Port 3 [8086:1e14] (rev c4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Memory behind bridge: d0500000-d05fffff
Prefetchable memory behind bridge: 00000000bf200000-00000000bf2fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.3 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset
Family PCI Express Root Port 4 [8086:1e16] (rev c4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Memory behind bridge: d0400000-d04fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset
Family USB Enhanced Host Controller #1 [8086:1e26] (rev 04) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Device [103c:18df]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d0739000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1f.0 ISA bridge [0601]: Intel Corporation QM77 Express Chipset LPC
Controller [8086:1e55] (rev 04)
Subsystem: Hewlett-Packard Company Device [103c:18df]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 SATA controller [0106]: Intel Corporation 7 Series Chipset Family
6-port SATA Controller [AHCI mode] [8086:1e03] (rev 04) (prog-if 01 [AHCI 1.0])
Subsystem: Hewlett-Packard Company Device [103c:18df]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 42
Region 0: I/O ports at 20a8 [size=8]
Region 1: I/O ports at 20b4 [size=4]
Region 2: I/O ports at 20a0 [size=8]
Region 3: I/O ports at 20b0 [size=4]
Region 4: I/O ports at 2060 [size=32]
Region 5: Memory at d0738000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 7 Series/C210 Series Chipset Family
SMBus Controller [8086:1e22] (rev 04)
Subsystem: Hewlett-Packard Company Device [103c:18df]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at d0734000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at ef80 [size=32]
02:00.0 System peripheral [0880]: JMicron Technology Corp. SD/MMC Host
Controller [197b:2392] (rev 30)
Subsystem: Hewlett-Packard Company Device [103c:18df]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at d0503000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at bf200000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: sdhci-pci
02:00.2 SD Host controller [0805]: JMicron Technology Corp. Standard SD Host
Controller [197b:2391] (rev 30) (prog-if 01)
Subsystem: Hewlett-Packard Company Device [103c:18df]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 18
Region 0: Memory at d0502000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
03:00.0 Network controller [0280]: Intel Corporation Centrino Advanced-N 6235
[8086:088e] (rev 24)
Subsystem: Intel Corporation Centrino Advanced-N 6235 AGN [8086:4060]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 43
Region 0: Memory at d0400000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: iwlwifi
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 003: ID 138a:003d Validity Sensors, Inc.
Bus 001 Device 004: ID 05c8:034b Cheng Uei Precision Industry Co., Ltd
(Foxlink)
Bus 002 Device 007: ID 8087:07da Intel Corp.
Bus 003 Device 002: ID 0461:4d0f Primax Electronics, Ltd HP Optical Mouse
Bus 003 Device 003: ID 413c:2107 Dell Computer Corp.
-- System Information:
Debian Release: 7.4
APT prefers stable
APT policy: (500, 'stable')
Architecture: amd64 (x86_64)
Foreign Architectures: i386
Kernel: Linux 3.2.0-4-amd64 (SMP w/4 CPU cores)
Locale: LANG=C, LC_CTYPE=C (charmap=ANSI_X3.4-1968)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.2.0-4-amd64 depends on:
ii debconf [debconf-2.0] 1.5.49
ii initramfs-tools [linux-initramfs-tool] 0.115~bpo70+1
ii kmod 9-3
ii linux-base 3.5
ii module-init-tools 9-3
Versions of packages linux-image-3.2.0-4-amd64 recommends:
ii firmware-linux-free 3.2
Versions of packages linux-image-3.2.0-4-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 1.99-27+deb7u2
pn linux-doc-3.2 <none>
Versions of packages linux-image-3.2.0-4-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
ii firmware-iwlwifi 0.40~bpo70+1
pn firmware-libertas <none>
ii firmware-linux 0.36+wheezy.1
ii firmware-linux-nonfree 0.36+wheezy.1
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.2.0-4-amd64/postinst/ignoring-ramdisk:
linux-image-3.2.0-4-amd64/postinst/depmod-error-initrd-3.2.0-4-amd64: false
linux-image-3.2.0-4-amd64/prerm/removing-running-kernel-3.2.0-4-amd64: true
linux-image-3.2.0-4-amd64/postinst/missing-firmware-3.2.0-4-amd64:
--
To UNSUBSCRIBE, email to debian-kernel-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
Archive: https://lists.debian.org/20140411152049.12047.16396.reportbug@localhost
