Package: linux-image-3.9-1-686-pae
Version: 3.9.8-1
Severity: normal
Dear Maintainer,
I've a system with two hard disks3s - a SSD and an older IDE disk. The
SSD is the boot disk. The IDE disk is used for storing mass data.
At end of the shutdown the IDE disk
1) spins down for fractions of a seconds but audible
2) spins up again
3) spins down permanently, the system turns off in same moment
I think the spinning down -> up -> down is a bug.
The issue occurs at every shutdown with kernel 3.9-1-686-pae. It doesn't
occur with kernel 3.2.0-4-686-pae.
The shutdown log is a transcription of a recording shutdown process.
The syslog doesn't contains any information about this part of the
shutdown process. There are no disk errors during the system is up and
running.
What's the reason of this behaviour and how can I fix it?
Regards,
Carsten
** Shutdown log:
[ 3621.791148] pcieport 0000:00:1c.5: System wakeup enabled by ACPI
done.
Will now unmount temporary filesystems:tmpfs has been unmounted
none has been unmounted
. ok
[....] Will now deactivate swap:swapoff on /dev/sda2
. ok
[....] Will now unmount local filesystems:/dev/sda3 has been unmounted
/dev/sdal has been unmounted
. ok
[ ok ] Mounting root filesystem read-only...done.
[ info] Will now halt.
[ 3624.923550] kvm: exiting hardware virtualization
[ 3624.924414] sd 4:0:0:0: [sdb] Synchronizing SCSI cache
[ 3624.924905] sd 4:0:0:0: [sdb] Stopping disk
[ 3625.212165] sd 2:0:0:0: [sda] Synchronizing SCSI cache
[ 3625.212326] ad 2:0:0:0: [sda] Stopping disk
[ 3625.615374] ata3.00: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xe
frozen
[ 3625.615446] ata3.00: irq_stat 0x00400001, PHY RDY changed
[ 3625.615497] ata3: SError: { PHYRdyChg }
[ 3625.615534] ata3.00: failed command: STANDBY IMMEDIATE
[ 3625.615585] ata3.00: cmd e0/00:00:00:00:00/00:00:00:00:00/a0 tag 0
[ 3625.615585] res 50/00:00:00:00:00/00:00:00:00:00/a0 Emask 0x10
(ATA bus error)
[ 3625.615705] ata3.00: status: { DRDY }
[ 3625.615746] ata3: hard resetting link
[ 3626.335749] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 3626.400368] ata3.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) rejected
by device (Stat=0x51 Err=0x04)
[ 3626.400445] ata3.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK)
filtered out
[ 3626.400505] ata3.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION
OVERLAY) filtered out
[ 3629.646801] ata3.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) rejected
by device (Stat=0x51 Err=0x04)
[ 3629.646874] ata3.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK)
filtered out
[ 3629.646931] ata3.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION
OVERLAY) filtered out
[ 3629.649227] ata3.00: configured for UDMA/100
[ 3629.665886] ata3.00: device reported invalid CHS sector 0
[ 3629.668636] ata3: EH complete
[ 3629.668666] sd 2:0:0:0: [sda] START_STOP FAILED
[ 3629.668668] sd 2:0:0:0: [sda]
[ 3629.668669] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 3629.668671] sd 2:0:0:0: [sda]
[ 3629.668673] Sense Key : Aborted Command [current] [descriptor]
[ 3629.668675] sd 2:0:0:0: [sda]
[ 3629.668686] Add. Sense: No additional sense information
[ 3629.690983] mei 0000:00:16.0: stop
[ 3629.693846] ACPI: Preparing to enter system sleep state S5
Current ata3 details:
$ dmesg | grep ata3
[ 0.881971] ata3: SATA max UDMA/133 abar m2048@0xf7c16000 port 0xf7c16200
irq 44
[ 1.200526] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.202763] ata3.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) rejected
by device (Stat=0x51 Err=0x04)
[ 1.202814] ata3.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK)
filtered out
[ 1.202859] ata3.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION
OVERLAY) filtered out
[ 1.203017] ata3.00: ATA-7: SAMSUNG SP2514N, VF100-50, max UDMA/100
[ 1.203050] ata3.00: 488397168 sectors, multi 16: LBA48
[ 1.203081] ata3.00: applying bridge limits
[ 1.222989] ata3.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) rejected
by device (Stat=0x51 Err=0x04)
[ 1.223060] ata3.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK)
filtered out
[ 1.223102] ata3.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION
OVERLAY) filtered out
[ 1.223223] ata3.00: configured for UDMA/100
$ cat /sys/block/sda/device/queue_depth
1
$ cat /sys/block/sda/device/model
SAMSUNG SP2514N
-- Package-specific info:
** Version:
Linux version 3.9-1-686-pae (debian-kernel@lists.debian.org) (gcc version
4.7.3 (Debian 4.7.3-4) ) #1 SMP Debian 3.9.8-1
** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.9-1-686-pae root=UUID=71b3f925-391e-4f93-
aef2-3f58ac7da001 ro
** Tainted: O (4096)
* Out-of-tree module has been loaded.
** Kernel log:
[ 1.600282] usb 6-1: new high-speed USB device number 2 using ehci-pci
[ 1.732559] usb 6-1: New USB device found, idVendor=8087, idProduct=0024
[ 1.732605] usb 6-1: New USB device strings: Mfr=0, Product=0,
SerialNumber=0
[ 1.732818] hub 6-1:1.0: USB hub found
[ 1.732919] hub 6-1:1.0: 8 ports detected
[ 1.777699] [drm] Initialized drm 1.1.0 20060810
[ 1.785902] SGI XFS with ACLs, security attributes, realtime, large
block/inode numbers, no debug enabled
[ 1.786734] XFS (sdb1): Mounting Filesystem
[ 1.839838] XFS (sdb1): Ending clean mount
[ 2.005620] udevd[446]: starting version 175
[ 2.049992] input: Power Button as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2
[ 2.050043] ACPI: Power Button [PWRB]
[ 2.050102] input: Power Button as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 2.050146] ACPI: Power Button [PWRF]
[ 2.050571] ACPI: Requesting acpi_cpufreq
[ 2.063353] ACPI Warning: 0x00000428-0x0000042f SystemIO conflicts with
Region \PMIO 1 (20130117/utaddress-251)
[ 2.063431] ACPI: If an ACPI driver is available for this device, you
should use it instead of the native driver
[ 2.063478] ACPI Warning: 0x00000530-0x0000053f SystemIO conflicts with
Region \GPR2 1 (20130117/utaddress-251)
[ 2.063553] ACPI Warning: 0x00000530-0x0000053f SystemIO conflicts with
Region \GPIO 2 (20130117/utaddress-251)
[ 2.063629] ACPI: If an ACPI driver is available for this device, you
should use it instead of the native driver
[ 2.063674] ACPI Warning: 0x00000500-0x0000052f SystemIO conflicts with
Region \GPR2 1 (20130117/utaddress-251)
[ 2.063749] ACPI Warning: 0x00000500-0x0000052f SystemIO conflicts with
Region \GPIO 2 (20130117/utaddress-251)
[ 2.063825] ACPI: If an ACPI driver is available for this device, you
should use it instead of the native driver
[ 2.063893] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 2.064812] ACPI Warning: 0x0000f040-0x0000f05f SystemIO conflicts with
Region \_SB_.PCI0.SBUS.SMBI 1 (20130117/utaddress-251)
[ 2.064889] ACPI: If an ACPI driver is available for this device, you
should use it instead of the native driver
[ 2.070719] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 2.070827] [drm] Memory usable by graphics device = 2048M
[ 2.070861] i915 0000:00:02.0: setting latency timer to 64
[ 2.071055] i915 0000:00:02.0: irq 48 for MSI/MSI-X
[ 2.071060] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 2.071091] [drm] Driver supports precise vblank timestamp query.
[ 2.071177] vgaarb: device changed decodes:
PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 2.072266] wmi: Mapper loaded
[ 2.093857] microcode: CPU0 sig=0x306a9, pf=0x2, revision=0x15
[ 2.103782] iTCO_vendor_support: vendor-support=0
[ 2.105958] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10
[ 2.106020] iTCO_wdt: Found a Panther Point TCO device (Version=2,
TCOBASE=0x0460)
[ 2.106197] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 2.106322] platform microcode: firmware: agent aborted loading intel-
ucode/06-3a-09 (not found?)
[ 2.106394] microcode: CPU1 sig=0x306a9, pf=0x2, revision=0x15
[ 2.108347] platform microcode: firmware: agent aborted loading intel-
ucode/06-3a-09 (not found?)
[ 2.108427] microcode: CPU2 sig=0x306a9, pf=0x2, revision=0x15
[ 2.110821] platform microcode: firmware: agent aborted loading intel-
ucode/06-3a-09 (not found?)
[ 2.110899] microcode: CPU3 sig=0x306a9, pf=0x2, revision=0x15
[ 2.112767] platform microcode: firmware: agent aborted loading intel-
ucode/06-3a-09 (not found?)
[ 2.112855] microcode: Microcode Update Driver: v2.00
<tig...@aivazian.fsnet.co.uk>, Peter Oruba
[ 2.164651] fbcon: inteldrmfb (fb0) is primary device
[ 2.399042] Console: switching to colour frame buffer device 240x67
[ 2.410278] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 2.410334] i915 0000:00:02.0: registered panic notifier
[ 2.411126] acpi device:46: registered as cooling_device4
[ 2.411354] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 2.411475] input: Video Bus as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input5
[ 2.411697] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor
0
[ 2.411898] mei 0000:00:16.0: setting latency timer to 64
[ 2.411942] mei 0000:00:16.0: irq 49 for MSI/MSI-X
[ 2.415422] snd_hda_intel 0000:00:1b.0: irq 50 for MSI/MSI-X
[ 2.675927] input: HDA Digital PCBeep as
/devices/pci0000:00/0000:00:1b.0/input/input6
[ 2.801032] input: HDA Intel PCH HDMI/DP,pcm=8 as
/devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[ 2.801255] input: HDA Intel PCH HDMI/DP,pcm=7 as
/devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 2.801432] input: HDA Intel PCH HDMI/DP,pcm=3 as
/devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 2.801586] input: HDA Intel PCH Line as
/devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[ 2.801730] input: HDA Intel PCH Rear Mic as
/devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[ 2.801876] input: HDA Intel PCH Line Out CLFE as
/devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[ 2.802027] input: HDA Intel PCH Line Out Surround as
/devices/pci0000:00/0000:00:1b.0/sound/card0/input13
[ 2.802179] input: HDA Intel PCH Line Out Front as
/devices/pci0000:00/0000:00:1b.0/sound/card0/input14
[ 3.117101] Adding 8388604k swap on /dev/sda2. Priority:-1 extents:1
across:8388604k
[ 3.447407] fuse init (API version 7.21)
[ 3.580962] XFS (sda1): Mounting Filesystem
[ 3.640412] XFS (sda1): Ending clean mount
[ 3.655270] XFS (sda3): Mounting Filesystem
[ 3.807422] [drm] Enabling RC6 states: RC6 on, RC6p on, RC6pp off
[ 3.845110] XFS (sda3): Ending clean mount
[ 4.165959] tg3 0000:03:00.0: irq 51 for MSI/MSI-X
[ 4.165970] tg3 0000:03:00.0: irq 52 for MSI/MSI-X
[ 4.165978] tg3 0000:03:00.0: irq 53 for MSI/MSI-X
[ 4.165986] tg3 0000:03:00.0: irq 54 for MSI/MSI-X
[ 4.165994] tg3 0000:03:00.0: irq 55 for MSI/MSI-X
[ 4.618169] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 5.134010] lp: driver loaded but no devices found
[ 5.137736] ppdev: user-space parallel port driver
[ 5.334455] vboxdrv: Found 4 processor cores.
[ 5.339285] vboxdrv: fAsync=0 offMin=0x19e offMax=0xfcb
[ 5.339327] vboxdrv: TSC mode is 'synchronous', kernel timer mode is
'normal'.
[ 5.339327] vboxdrv: Successfully loaded version 4.2.16 (interface
0x001a0005).
[ 5.559701] vboxpci: IOMMU not found (not compiled)
[ 6.287942] tg3 0000:03:00.0 eth0: Link is up at 100 Mbps, full duplex
[ 6.287946] tg3 0000:03:00.0 eth0: Flow control is on for TX and on for RX
[ 6.287948] tg3 0000:03:00.0 eth0: EEE is disabled
[ 6.287960] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 11.687450] tg3 0000:03:00.0 eth0: Link is down
[ 13.598637] tg3 0000:03:00.0 eth0: Link is up at 100 Mbps, full duplex
[ 13.598646] tg3 0000:03:00.0 eth0: Flow control is on for TX and on for RX
[ 13.598649] tg3 0000:03:00.0 eth0: EEE is disabled
[ 695.038705] tg3 0000:03:00.0 eth0: Link is down
[ 696.602774] tg3 0000:03:00.0 eth0: Link is up at 100 Mbps, full duplex
[ 696.602784] tg3 0000:03:00.0 eth0: Flow control is on for TX and on for RX
[ 696.602787] tg3 0000:03:00.0 eth0: EEE is disabled
[ 3109.543243] warning: `VirtualBox' uses 32-bit capabilities (legacy support
in use)
** Model information
not available
** Loaded modules:
pci_stub
vboxpci(O)
vboxnetadp(O)
vboxnetflt(O)
vboxdrv(O)
parport_pc
ppdev
lp
parport
w83l785ts
asb100
hwmon_vid
i2c_nforce2
psmouse
fuse
snd_hda_codec_hdmi
snd_hda_codec_realtek
coretemp
kvm_intel
kvm
crc32c_intel
aesni_intel
aes_i586
xts
lrw
gf128mul
ablk_helper
cryptd
snd_hda_intel
snd_hda_codec
snd_hwdep
snd_pcm_oss
snd_mixer_oss
snd_pcm
mxm_wmi
iTCO_wdt
snd_page_alloc
iTCO_vendor_support
snd_seq_midi
snd_seq_midi_event
snd_rawmidi
microcode
snd_seq
snd_seq_device
snd_timer
evdev
mei
snd
wmi
pcspkr
i915
i2c_i801
lpc_ich
video
acpi_cpufreq
drm_kms_helper
mfd_core
mperf
i2c_algo_bit
soundcore
processor
button
thermal_sys
xfs
crc32c
libcrc32c
drm
i2c_core
hid_generic
usbhid
hid
sd_mod
crc_t10dif
sg
sr_mod
cdrom
tg3
ptp
pps_core
libphy
firewire_ohci
firewire_core
crc_itu_t
ehci_pci
ehci_hcd
xhci_hcd
ahci
libahci
libata
scsi_mod
usbcore
usb_common
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Xeon E3-1200 v2/3rd Gen Core
processor DRAM Controller [8086:0150] (rev 09)
Subsystem: ASRock Incorporation Device [1849:0150]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:02.0 VGA compatible controller [0300]: Intel Corporation Xeon E3-1200
v2/3rd Gen Core processor Graphics Controller [8086:0162] (rev 09) (prog-if 00
[VGA controller])
Subsystem: ASRock Incorporation Device [1849:0162]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 48
Region 0: Memory at f7400000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at f000 [size=64]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:14.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset
Family USB xHCI Host Controller [8086:1e31] (rev 04) (prog-if 30 [XHCI])
Subsystem: ASRock Incorporation Device [1849:1e31]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 46
Region 0: Memory at f7c00000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
00:16.0 Communication controller [0780]: Intel Corporation 7 Series/C210
Series Chipset Family MEI Controller #1 [8086:1e3a] (rev 04)
Subsystem: ASRock Incorporation Device [1849:1e3a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 49
Region 0: Memory at f7c1a000 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
Kernel driver in use: mei
00:1a.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset
Family USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) (prog-if 20
[EHCI])
Subsystem: ASRock Incorporation Device [1849:1e2d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f7c18000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:1b.0 Audio device [0403]: Intel Corporation 7 Series/C210 Series Chipset
Family High Definition Audio Controller [8086:1e20] (rev 04)
Subsystem: ASRock Incorporation Device [1849:1898]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 50
Region 0: Memory at f7c10000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset
Family PCI Express Root Port 1 [8086:1e10] (rev c4) (prog-if 00 [Normal
decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.4 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset
Family PCI Express Root Port 5 [8086:1e18] (rev c4) (prog-if 00 [Normal
decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: f7b00000-f7bfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.5 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset
Family PCI Express Root Port 6 [8086:1e1a] (rev c4) (prog-if 00 [Normal
decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Memory behind bridge: f7a00000-f7afffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f00fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.6 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset
Family PCI Express Root Port 7 [8086:1e1c] (rev c4) (prog-if 00 [Normal
decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Memory behind bridge: f7900000-f79fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.7 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset
Family PCI Express Root Port 8 [8086:1e1e] (rev c4) (prog-if 00 [Normal
decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=0a, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: f7800000-f78fffff
Prefetchable memory behind bridge: 00000000dfb00000-00000000dfcfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset
Family USB Enhanced Host Controller #1 [8086:1e26] (rev 04) (prog-if 20
[EHCI])
Subsystem: ASRock Incorporation Device [1849:1e26]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f7c17000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:1f.0 ISA bridge [0601]: Intel Corporation Z77 Express Chipset LPC
Controller [8086:1e44] (rev 04)
Subsystem: ASRock Incorporation Device [1849:1e44]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
00:1f.2 SATA controller [0106]: Intel Corporation 7 Series/C210 Series Chipset
Family 6-port SATA Controller [AHCI mode] [8086:1e02] (rev 04) (prog-if 01
[AHCI 1.0])
Subsystem: ASRock Incorporation Device [1849:1e02]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 44
Region 0: I/O ports at f0b0 [size=8]
Region 1: I/O ports at f0a0 [size=4]
Region 2: I/O ports at f090 [size=8]
Region 3: I/O ports at f080 [size=4]
Region 4: I/O ports at f060 [size=32]
Region 5: Memory at f7c16000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 7 Series/C210 Series Chipset Family
SMBus Controller [8086:1e22] (rev 04)
Subsystem: ASRock Incorporation Device [1849:1e22]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f7c15000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at f040 [size=32]
02:00.0 SATA controller [0106]: ASMedia Technology Inc. ASM1062 Serial ATA
Controller [1b21:0612] (rev 01) (prog-if 01 [AHCI 1.0])
Subsystem: ASRock Incorporation Device [1849:0612]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 45
Region 0: I/O ports at e050 [size=8]
Region 1: I/O ports at e040 [size=4]
Region 2: I/O ports at e030 [size=8]
Region 3: I/O ports at e020 [size=4]
Region 4: I/O ports at e000 [size=32]
Region 5: Memory at f7b00000 (32-bit, non-prefetchable) [size=512]
Capabilities: <access denied>
Kernel driver in use: ahci
03:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM57781
Gigabit Ethernet PCIe [14e4:16b1] (rev 10)
Subsystem: ASRock Incorporation Device [1849:96b1]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at f0010000 (64-bit, prefetchable) [size=64K]
Region 2: Memory at f0000000 (64-bit, prefetchable) [size=64K]
Expansion ROM at f7a00000 [disabled] [size=2K]
Capabilities: <access denied>
Kernel driver in use: tg3
04:00.0 USB controller [0c03]: Etron Technology, Inc. EJ168 USB 3.0 Host
Controller [1b6f:7023] (rev 01) (prog-if 30 [XHCI])
Subsystem: ASRock Incorporation Device [1849:7023]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 47
Region 0: Memory at f7900000 (64-bit, non-prefetchable) [size=32K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
05:00.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8605 PCI Express 4-port
Gen2 Switch [10b5:8605] (rev aa) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=05, secondary=06, subordinate=0a, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: f7800000-f78fffff
Prefetchable memory behind bridge: 00000000dfb00000-00000000dfcfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
06:01.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8605 PCI Express 4-port
Gen2 Switch [10b5:8605] (rev aa) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=06, secondary=07, subordinate=07, sec-latency=0
Prefetchable memory behind bridge: 00000000dfb00000-00000000dfcfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
06:02.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8605 PCI Express 4-port
Gen2 Switch [10b5:8605] (rev aa) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=06, secondary=08, subordinate=08, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
06:03.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8605 PCI Express 4-port
Gen2 Switch [10b5:8605] (rev aa) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=06, secondary=09, subordinate=0a, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: f7800000-f78fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
09:00.0 PCI bridge [0604]: ASMedia Technology Inc. ASM1083/1085 PCIe to PCI
Bridge [1b21:1080] (rev 01) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=09, secondary=0a, subordinate=0a, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: f7800000-f78fffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
0a:02.0 FireWire (IEEE 1394) [0c00]: VIA Technologies, Inc. VT6306/7/8 [Fire
II(M)] IEEE 1394 OHCI Controller [1106:3044] (rev c0) (prog-if 10 [OHCI])
Subsystem: ASRock Incorporation Device [1849:3044]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 32 (8000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f7800000 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at d000 [size=128]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
** USB devices:
Bus 006 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 006 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 002: ID 046d:c03e Logitech, Inc. Premium Optical Wheel Mouse
(M-BT58)
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: jessie/sid
APT prefers testing
APT policy: (500, 'testing'), (1, 'experimental')
Architecture: i386 (i686)
Kernel: Linux 3.9-1-686-pae (SMP w/4 CPU cores)
Locale: LANG=de_DE@euro, LC_CTYPE=de_DE@euro (charmap=ISO-8859-15)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-3.9-1-686-pae depends on:
ii debconf [debconf-2.0] 1.5.50
ii initramfs-tools [linux-initramfs-tool] 0.113
ii kmod 9-3
ii linux-base 3.5
ii module-init-tools 9-3
Versions of packages linux-image-3.9-1-686-pae recommends:
ii firmware-linux-free 3.2
ii libc6-i686 2.17-7
Versions of packages linux-image-3.9-1-686-pae suggests:
pn debian-kernel-handbook <none>
ii grub-pc 1.99-27+deb7u1
pn linux-doc-3.9 <none>
Versions of packages linux-image-3.9-1-686-pae is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.9-1-686-pae/prerm/removing-running-kernel-3.9-1-686-pae: true
* linux-image-3.9-1-686-pae/postinst/missing-firmware-3.9-1-686-pae:
linux-image-3.9-1-686-pae/postinst/ignoring-ramdisk:
linux-image-3.9-1-686-pae/postinst/depmod-error-initrd-3.9-1-686-pae: false
--
To UNSUBSCRIBE, email to debian-kernel-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
Archive: http://lists.debian.org/201308091909.05359.carstengrohm...@gmx.de
