--- Begin Message ---
Package: linux-2.6
Version: 2.6.39-2
Severity: normal
With linux-image-2.6.39-2-686-pae, my kernel's console does not use my
monitor's native resolution (1600x1200) and instead uses 1280x1024.
On the other hand linux-image-2.6.32-5-686-bigmem used 1600x1200 just fine.
My hardware is recognized by the X11 nouveau driver as "NV44" (note that
I don't actually use the X11 nouveau driver, but the fbdev instead because
the X11 nouveau driver ends up deciding it can't find any display, but that's
a separate problem that appears both with 2.6.32 and 2.6.39).
I include the nouveau&drm part of the dmesg output in both the 2.6.32
and 2.6.39 cases.
Stefan
-- Package-specific info:
** Version:
Linux version 2.6.39-2-686-pae (Debian 2.6.39-2) (b...@decadent.org.uk) (gcc
version 4.4.6 (Debian 4.4.6-3) ) #1 SMP Wed Jun 8 11:33:14 UTC 2011
** Command line:
BOOT_IMAGE=/vmlinuz-2.6.39-2-686-pae root=/dev/mapper/Pastel-root ro quiet
** Tainted: W (512)
* Taint on warning.
** Kernel log:
[ 507.051791] wlan0: RX AssocResp from 00:18:3f:cb:5a:59 (capab=0x431 status=0
aid=2)
[ 507.051794] wlan0: associated
[ 507.063957] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 517.888016] wlan0: no IPv6 routers present
[ 572.629300] wlan0: deauthenticating from 00:18:3f:cb:5a:59 by local choice
(reason=3)
[ 572.666305] cfg80211: Calling CRDA to update world regulatory domain
[ 572.777369] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 574.787887] forcedeth 0000:00:0a.0: eth-down: no link during initialization
[ 574.788442] ADDRCONF(NETDEV_UP): eth-down: link is not ready
[ 591.598512] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 591.713625] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 591.811894] forcedeth 0000:00:0a.0: eth-down: no link during initialization
[ 591.812445] ADDRCONF(NETDEV_UP): eth-down: link is not ready
[ 593.967189] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 596.240211] wlan0: authenticate with 00:18:3f:cb:5a:59 (try 1)
[ 596.242584] wlan0: authenticated
[ 596.262207] wlan0: associate with 00:18:3f:cb:5a:59 (try 1)
[ 596.265716] wlan0: RX AssocResp from 00:18:3f:cb:5a:59 (capab=0x431 status=0
aid=2)
[ 596.265719] wlan0: associated
[ 596.277868] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 606.544021] wlan0: no IPv6 routers present
[ 659.629639] wlan0: deauthenticating from 00:18:3f:cb:5a:59 by local choice
(reason=3)
[ 659.673770] cfg80211: Calling CRDA for country: US
[ 659.789457] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 661.836092] forcedeth 0000:00:0a.0: eth-down: no link during initialization
[ 661.836637] ADDRCONF(NETDEV_UP): eth-down: link is not ready
[ 664.278700] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 664.399318] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 664.500514] forcedeth 0000:00:0a.0: eth-down: no link during initialization
[ 664.501025] ADDRCONF(NETDEV_UP): eth-down: link is not ready
[ 666.633029] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 668.912543] wlan0: authenticate with 00:18:3f:cb:5a:59 (try 1)
[ 668.914792] wlan0: authenticated
[ 668.934288] wlan0: associate with 00:18:3f:cb:5a:59 (try 1)
[ 668.936671] wlan0: RX AssocResp from 00:18:3f:cb:5a:59 (capab=0x431 status=0
aid=2)
[ 668.936673] wlan0: associated
[ 668.948822] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 679.520016] wlan0: no IPv6 routers present
[ 734.629790] wlan0: deauthenticating from 00:18:3f:cb:5a:59 by local choice
(reason=3)
[ 734.673795] cfg80211: Calling CRDA to update world regulatory domain
[ 734.797609] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 736.915941] forcedeth 0000:00:0a.0: eth-down: no link during initialization
[ 736.916491] ADDRCONF(NETDEV_UP): eth-down: link is not ready
[ 765.490434] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 765.610297] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 765.711946] forcedeth 0000:00:0a.0: eth-down: no link during initialization
[ 765.712497] ADDRCONF(NETDEV_UP): eth-down: link is not ready
[ 767.867622] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 770.140523] wlan0: authenticate with 00:18:3f:cb:5a:59 (try 1)
[ 770.142021] wlan0: authenticated
[ 770.161643] wlan0: associate with 00:18:3f:cb:5a:59 (try 1)
[ 770.164276] wlan0: RX AssocResp from 00:18:3f:cb:5a:59 (capab=0x431 status=0
aid=2)
[ 770.164279] wlan0: associated
[ 770.176555] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 780.976017] wlan0: no IPv6 routers present
[ 838.851163] wlan0: deauthenticating from 00:18:3f:cb:5a:59 by local choice
(reason=3)
[ 838.894417] cfg80211: Calling CRDA for country: US
[ 839.001334] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 844.402527] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 844.525896] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 844.616196] forcedeth 0000:00:0a.0: eth-down: no link during initialization
[ 844.616707] ADDRCONF(NETDEV_UP): eth-down: link is not ready
[ 846.751595] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 849.028493] wlan0: authenticate with 00:18:3f:cb:5a:59 (try 1)
[ 849.030744] wlan0: authenticated
[ 849.050240] wlan0: associate with 00:18:3f:cb:5a:59 (try 1)
[ 849.052124] wlan0: RX AssocResp from 00:18:3f:cb:5a:59 (capab=0x431 status=0
aid=2)
[ 849.052127] wlan0: associated
[ 849.064275] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 859.824015] wlan0: no IPv6 routers present
[ 871.328041] tun: Universal TUN/TAP device driver, 1.6
[ 871.328045] tun: (C) 1999-2004 Max Krasnyansky <m...@qualcomm.com>
[ 1004.002140] ------------[ cut here ]------------
[ 1004.002150] WARNING: at
/build/buildd-linux-2.6_2.6.39-2-i386-Ow09ch/linux-2.6-2.6.39/debian/build/source_i386_none/block/genhd.c:1556
disk_clear_events+0xa9/0xd2()
[ 1004.002153] Hardware name: System Product Name
[ 1004.002155] Modules linked in: tun arc4 ecb rt73usb rt2x00usb rt2x00lib
mac80211 cfg80211 mperf cpufreq_stats cpufreq_conservative cpufreq_userspace
cpufreq_powersave ppdev lp rfcomm bnep bluetooth rfkill crc16 autofs4
binfmt_misc ppp_async crc_ccitt ppp_generic slhc fuse snd_wavefront snd_cs4236
snd_wss_lib snd_opl3_lib snd_intel8x0 snd_hwdep snd_ac97_codec snd_mpu401
snd_mpu401_uart ac97_bus snd_seq_midi snd_pcm snd_seq_midi_event snd_rawmidi
nouveau snd_seq snd_timer snd_seq_device ttm drm_kms_helper drm snd evdev
parport_pc k8temp asus_atk0110 i2c_algo_bit serio_raw power_supply ns558
i2c_nforce2 video parport button snd_page_alloc soundcore gameport pcspkr
processor i2c_core ext3 jbd mbcache dm_mod usbhid hid sg sr_mod usb_storage
cdrom sd_mod crc_t10dif uas ata_generic ohci_hcd pata_amd sata_nv thermal
libata ehci_hcd fan firewire_ohci scsi_mod usbcore floppy skge thermal_sys
forcedeth firewire_core crc_itu_t [last unloaded: scsi_wait_scan]
[ 1004.002221] Pid: 3578, comm: udisks-daemon Not tainted 2.6.39-2-686-pae #1
[ 1004.002223] Call Trace:
[ 1004.002229] [<c1036b4d>] ? warn_slowpath_common+0x6a/0x7b
[ 1004.002233] [<c114ae17>] ? disk_clear_events+0xa9/0xd2
[ 1004.002236] [<c1036b6b>] ? warn_slowpath_null+0xd/0x10
[ 1004.002239] [<c114ae17>] ? disk_clear_events+0xa9/0xd2
[ 1004.002248] [<c10ecccd>] ? check_disk_change+0x17/0x45
[ 1004.002261] [<f829b421>] ? sd_open+0xc8/0x164 [sd_mod]
[ 1004.002264] [<c10ed7da>] ? __blkdev_get+0xb5/0x2f3
[ 1004.002267] [<c10edba4>] ? blkdev_get+0x18c/0x270
[ 1004.002271] [<c11204b1>] ? fsnotify_perm+0x4f/0x5a
[ 1004.002274] [<c10ed174>] ? bd_acquire+0x20/0x8f
[ 1004.002278] [<c10cb191>] ? __dentry_open+0x15b/0x236
[ 1004.002281] [<c10cb2ef>] ? nameidata_to_filp+0x3a/0x45
[ 1004.002284] [<c10edc88>] ? blkdev_get+0x270/0x270
[ 1004.002287] [<c10d5119>] ? do_last+0x441/0x51c
[ 1004.002290] [<c10d5681>] ? path_openat+0x97/0x27d
[ 1004.002293] [<c10d590b>] ? do_filp_open+0x21/0x5d
[ 1004.002297] [<c10caefc>] ? do_sys_open+0x58/0xd1
[ 1004.002299] [<c10cafb9>] ? sys_open+0x1e/0x23
[ 1004.002304] [<c12b715f>] ? sysenter_do_call+0x12/0x28
[ 1004.002307] ---[ end trace df70caca70b2518c ]---
[ 1459.410849] padlock_sha: VIA PadLock Hash Engine not detected.
[ 1459.424470] PPP MPPE Compression module registered
** Model information
not available
** Loaded modules:
Module Size Used by
sha1_generic 12511 4
ppp_mppe 12789 2
tun 17663 2
arc4 12418 4
ecb 12649 4
rt73usb 21878 0
rt2x00usb 13249 1 rt73usb
rt2x00lib 28634 2 rt73usb,rt2x00usb
mac80211 164606 2 rt2x00usb,rt2x00lib
cfg80211 107076 2 rt2x00lib,mac80211
mperf 12387 0
cpufreq_stats 12670 0
cpufreq_conservative 12987 0
cpufreq_userspace 12520 0
cpufreq_powersave 12422 0
ppdev 12621 0
lp 12858 0
rfcomm 31961 0
bnep 17147 2
bluetooth 92361 10 rfcomm,bnep
rfkill 18510 3 cfg80211,bluetooth
crc16 12327 1 bluetooth
autofs4 22520 1
binfmt_misc 12778 1
ppp_async 12845 1
crc_ccitt 12331 1 ppp_async
ppp_generic 21823 6 ppp_mppe,ppp_async
slhc 12498 1 ppp_generic
fuse 55666 1
snd_wavefront 30608 0
snd_cs4236 26314 0
snd_wss_lib 22401 2 snd_wavefront,snd_cs4236
snd_opl3_lib 13141 2 snd_wavefront,snd_cs4236
snd_intel8x0 22287 0
snd_hwdep 12906 2 snd_wavefront,snd_opl3_lib
snd_ac97_codec 83732 1 snd_intel8x0
snd_mpu401 12592 0
snd_mpu401_uart 13299 3 snd_wavefront,snd_cs4236,snd_mpu401
ac97_bus 12462 1 snd_ac97_codec
snd_seq_midi 12744 0
snd_pcm 52731 4
snd_cs4236,snd_wss_lib,snd_intel8x0,snd_ac97_codec
snd_seq_midi_event 13124 1 snd_seq_midi
snd_rawmidi 22407 3 snd_wavefront,snd_mpu401_uart,snd_seq_midi
nouveau 466427 3
snd_seq 39172 2 snd_seq_midi,snd_seq_midi_event
snd_timer 22171 4 snd_wss_lib,snd_opl3_lib,snd_pcm,snd_seq
snd_seq_device 12995 4 snd_opl3_lib,snd_seq_midi,snd_rawmidi,snd_seq
ttm 46736 1 nouveau
drm_kms_helper 26550 1 nouveau
drm 129190 3 nouveau,ttm,drm_kms_helper
snd 38189 14
snd_wavefront,snd_cs4236,snd_wss_lib,snd_opl3_lib,snd_intel8x0,snd_hwdep,snd_ac97_codec,snd_mpu401,snd_mpu401_uart,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
evdev 13084 15
parport_pc 21895 1
k8temp 12475 0
asus_atk0110 17092 0
i2c_algo_bit 12706 1 nouveau
serio_raw 12758 0
power_supply 13283 1 nouveau
ns558 12417 0
i2c_nforce2 12520 0
video 17345 1 nouveau
parport 27018 3 ppdev,lp,parport_pc
button 12783 1 nouveau
snd_page_alloc 12841 3 snd_wss_lib,snd_intel8x0,snd_pcm
soundcore 12878 1 snd
gameport 13332 2 ns558
pcspkr 12515 0
processor 26983 0
i2c_core 19022 5
nouveau,drm_kms_helper,drm,i2c_algo_bit,i2c_nforce2
ext3 102125 5
jbd 40818 1 ext3
mbcache 12810 1 ext3
dm_mod 56401 26
usbhid 35206 0
hid 59841 1 usbhid
sg 21385 0
sr_mod 17418 0
usb_storage 34951 0
cdrom 34631 1 sr_mod
sd_mod 35060 5
crc_t10dif 12332 1 sd_mod
uas 12975 0
ata_generic 12439 0
ohci_hcd 21898 0
pata_amd 13076 0
sata_nv 22047 3
thermal 13058 0
libata 132100 3 ata_generic,pata_amd,sata_nv
ehci_hcd 34885 0
fan 12594 0
firewire_ohci 26332 0
scsi_mod 134453 6 sg,sr_mod,sd_mod,usb_storage,uas,libata
usbcore 99225 8
rt73usb,rt2x00usb,usbhid,usb_storage,uas,ohci_hcd,ehci_hcd
floppy 47893 0
skge 39547 0
thermal_sys 17667 4 video,processor,thermal,fan
forcedeth 47955 0
firewire_core 42365 1 firewire_ohci
crc_itu_t 12331 2 rt73usb,firewire_core
** PCI devices:
00:00.0 Memory controller [0580]: nVidia Corporation CK804 Memory Controller
[10de:005e] (rev a3)
Subsystem: ASUSTeK Computer Inc. A8N-E Mainboard [1043:815a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:01.0 ISA bridge [0601]: nVidia Corporation CK804 ISA Bridge [10de:0050] (rev
a3)
Subsystem: ASUSTeK Computer Inc. K8N4-E or A8N-E Mainboard [1043:815a]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
00:01.1 SMBus [0c05]: nVidia Corporation CK804 SMBus [10de:0052] (rev a2)
Subsystem: ASUSTeK Computer Inc. K8N4-E or A8N-E Mainboard [1043:815a]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 255
Region 0: I/O ports at e400 [size=32]
Region 4: I/O ports at 4c00 [size=64]
Region 5: I/O ports at 4c40 [size=64]
Capabilities: <access denied>
Kernel driver in use: nForce2_smbus
00:02.0 USB Controller [0c03]: nVidia Corporation CK804 USB Controller
[10de:005a] (rev a2) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. K8N4-E or A8N-E Mainboard [1043:815a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 23
Region 0: Memory at d5004000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
00:02.1 USB Controller [0c03]: nVidia Corporation CK804 USB Controller
[10de:005b] (rev a3) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. K8N4-E or A8N-E Mainboard [1043:815a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 22
Region 0: Memory at d5005000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:04.0 Multimedia audio controller [0401]: nVidia Corporation CK804 AC'97
Audio Controller [10de:0059] (rev a2)
Subsystem: ASUSTeK Computer Inc. K8N4-E or A8N-E Mainboard [1043:812a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at dc00 [size=256]
Region 1: I/O ports at e000 [size=256]
Region 2: Memory at d5003000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: Intel ICH
00:06.0 IDE interface [0101]: nVidia Corporation CK804 IDE [10de:0053] (rev f2)
(prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. K8N4-E or A8N-E Mainboard [1043:815a]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[size=1]
Region 4: I/O ports at f000 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_amd
00:07.0 IDE interface [0101]: nVidia Corporation CK804 Serial ATA Controller
[10de:0054] (rev f3) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. A8N-E Mainboard [1043:815a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at 09f0 [size=8]
Region 1: I/O ports at 0bf0 [size=4]
Region 2: I/O ports at 0970 [size=8]
Region 3: I/O ports at 0b70 [size=4]
Region 4: I/O ports at d800 [size=16]
Region 5: Memory at d5002000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: sata_nv
00:08.0 IDE interface [0101]: nVidia Corporation CK804 Serial ATA Controller
[10de:0055] (rev f3) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. K8N4-E or A8N-E Mainboard [1043:815a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at 09e0 [size=8]
Region 1: I/O ports at 0be0 [size=4]
Region 2: I/O ports at 0960 [size=8]
Region 3: I/O ports at 0b60 [size=4]
Region 4: I/O ports at c400 [size=16]
Region 5: Memory at d5001000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: sata_nv
00:09.0 PCI bridge [0604]: nVidia Corporation CK804 PCI Bridge [10de:005c] (rev
a2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=128
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: d3000000-d4ffffff
Prefetchable memory behind bridge: d5100000-d51fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR+
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
00:0a.0 Bridge [0680]: nVidia Corporation CK804 Ethernet Controller [10de:0057]
(rev a3)
Subsystem: ASUSTeK Computer Inc. K8N4-E or A8N-E Mainboard [1043:8141]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx+
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 23
Region 0: Memory at d5000000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at b000 [size=8]
Capabilities: <access denied>
Kernel driver in use: forcedeth
00:0b.0 PCI bridge [0604]: nVidia Corporation CK804 PCIE Bridge [10de:005d]
(rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:0c.0 PCI bridge [0604]: nVidia Corporation CK804 PCIE Bridge [10de:005d]
(rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:0d.0 PCI bridge [0604]: nVidia Corporation CK804 PCIE Bridge [10de:005d]
(rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:0e.0 PCI bridge [0604]: nVidia Corporation CK804 PCIE Bridge [10de:005d]
(rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: d0000000-d2ffffff
Prefetchable memory behind bridge: 00000000c0000000-00000000cfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Kernel driver in use: k8temp
01:00.0 VGA compatible controller [0300]: nVidia Corporation NV44 [GeForce 6200
TurboCache(TM)] [10de:0161] (rev a1) (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:81ba]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at d0000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at d1000000 (64-bit, non-prefetchable) [size=16M]
[virtual] Expansion ROM at d2000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: nouveau
05:0b.0 FireWire (IEEE 1394) [0c00]: Texas Instruments TSB43AB22/A
IEEE-1394a-2000 Controller (PHY/Link) [104c:8023] (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. K8N4-E Mainboard [1043:808b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d4008000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at d4004000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
05:0c.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8001
Gigabit Ethernet Controller [11ab:4320] (rev 13)
Subsystem: ASUSTeK Computer Inc. Marvell 88E8001 Gigabit Ethernet
Controller (Asus) [1043:811a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (5750ns min, 7750ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at d4000000 (32-bit, non-prefetchable) [size=16K]
Region 1: I/O ports at a000 [size=256]
[virtual] Expansion ROM at d5100000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: skge
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 05e3:0710 Genesys Logic, Inc. USB 2.0 33-in-1 Card Reader
Bus 002 Device 002: ID 04b3:3016 IBM Corp. UltraNav Keyboard Hub
Bus 002 Device 003: ID 046d:c03e Logitech, Inc. Premium Optical Wheel Mouse
(M-BT58)
Bus 002 Device 004: ID 04b3:3019 IBM Corp.
Bus 002 Device 005: ID 06cb:0009 Synaptics, Inc. Composite TouchPad and
TrackPoint
Bus 001 Device 005: ID 050d:705a Belkin Components F5D7050 Wireless G Adapter
v3000 [Ralink RT2573]
-- System Information:
Debian Release: wheezy/sid
APT prefers testing
APT policy: (990, 'testing'), (500, 'unstable'), (500, 'stable'), (1,
'experimental')
Architecture: i386 (i686)
Kernel: Linux 2.6.39-2-686-pae (SMP w/2 CPU cores)
Locale: LANG=fr_CH.UTF-8, LC_CTYPE=fr_CH.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.39-2-686-pae depends on:
ii debconf [debconf-2.0] 1.5.39 Debian configuration management sy
ii initramfs-tools [linux-initra 0.99 tools for generating an initramfs
ii linux-base 3.2 Linux image base package
ii module-init-tools 3.16-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.39-2-686-pae recommends:
ii firmware-linux-free 3 Binary firmware for various driver
ii libc6-i686 2.13-7 Embedded GNU C Library: Shared lib
Versions of packages linux-image-2.6.39-2-686-pae suggests:
ii grub-pc 1.99-6 GRand Unified Bootloader, version
pn linux-doc-2.6.39 <none> (no description available)
Versions of packages linux-image-2.6.39-2-686-pae is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
ii firmware-iwlwifi 0.30 Binary firmware for Intel Wireless
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
ii firmware-ralink 0.30 Binary firmware for Ralink wireles
pn xen-hypervisor <none> (no description available)
-- debconf information:
linux-image-2.6.39-2-686-pae/postinst/depmod-error-initrd-2.6.39-2-686-pae:
false
* linux-image-2.6.39-2-686-pae/postinst/missing-firmware-2.6.39-2-686-pae:
linux-image-2.6.39-2-686-pae/prerm/removing-running-kernel-2.6.39-2-686-pae:
true
linux-image-2.6.39-2-686-pae/postinst/ignoring-ramdisk:
[ 9.358491] [drm] Initialized drm 1.1.0 20060810
[ 9.483882] nouveau 0000:01:00.0: PCI INT A -> Link[APC3] -> GSI 18 (level,
low) -> IRQ 18
[ 9.483888] nouveau 0000:01:00.0: setting latency timer to 64
[ 9.485305] [drm] nouveau 0000:01:00.0: Detected an NV40 generation card
(0x044100a2)
[ 9.487006] [drm] nouveau 0000:01:00.0: Attempting to load BIOS image from
PRAMIN
[ 9.565555] [drm] nouveau 0000:01:00.0: ... appears to be valid
[ 9.565559] [drm] nouveau 0000:01:00.0: BIT BIOS found
[ 9.565562] [drm] nouveau 0000:01:00.0: Bios version 05.44.02.11
[ 9.565566] [drm] nouveau 0000:01:00.0: TMDS table version 1.1
[ 9.565568] [drm] nouveau 0000:01:00.0: BIT table 'd' not found
[ 9.565571] [drm] nouveau 0000:01:00.0: Found Display Configuration Block
version 3.0
[ 9.565575] [drm] nouveau 0000:01:00.0: Raw DCB entry 0: 01010310 00000028
[ 9.565578] [drm] nouveau 0000:01:00.0: Raw DCB entry 1: 01000302 00000000
[ 9.565581] [drm] nouveau 0000:01:00.0: Raw DCB entry 2: 020203f1 0000c020
[ 9.565584] [drm] nouveau 0000:01:00.0: DCB connector table: VHER 0x30 5 6 2
[ 9.565592] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 0 at offset
0xEBC4
[ 9.565755] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 1 at offset
0xEE99
[ 9.578873] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 2 at offset
0xF2D1
[ 9.578895] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 3 at offset
0xF42E
[ 9.580020] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 4 at offset
0xF4DC
[ 9.598928] [drm] nouveau 0000:01:00.0: mem timing table length unknown: 14
[ 9.598964] [drm] nouveau 0000:01:00.0: 1 available performance level(s)
[ 9.598967] [drm] nouveau 0000:01:00.0: 0: memory 0MHz
[ 9.598976] [drm] nouveau 0000:01:00.0: c: memory 399MHz core 199MHz
[ 9.599080] [TTM] Zone kernel: Available graphics memory: 432048 kiB.
[ 9.599082] [TTM] Zone highmem: Available graphics memory: 2073492 kiB.
[ 9.599084] [TTM] Initializing pool allocator.
[ 9.599105] [drm] nouveau 0000:01:00.0: Detected 16MiB VRAM
[ 9.604967] [drm] nouveau 0000:01:00.0: 512 MiB GART (aperture)
[ 9.605045] [drm] nouveau 0000:01:00.0: Saving VGA fonts
[ 9.661965] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 9.661967] [drm] No driver support for vblank timestamp query.
[ 9.662426] [drm] nouveau 0000:01:00.0: Setting dpms mode 3 on vga encoder
(output 0)
[ 9.662430] [drm] nouveau 0000:01:00.0: Setting dpms mode 3 on tmds encoder
(output 1)
[ 9.662433] [drm] nouveau 0000:01:00.0: Setting dpms mode 3 on TV encoder
(output 2)
[ 9.856666] [drm] nouveau 0000:01:00.0: allocated 1280x1024 fb: 0x49000, bo
f714c000
[ 9.856755] fbcon: nouveaufb (fb0) is primary device
[ 9.870631] [drm] nouveau 0000:01:00.0: 0xD149: Parsing digital output
script table
[ 9.920260] [drm] nouveau 0000:01:00.0: Setting dpms mode 0 on tmds encoder
(output 1)
[ 9.920263] [drm] nouveau 0000:01:00.0: Output DVI-D-1 is running on CRTC 0
using output A
[ 9.924292] Console: switching to colour frame buffer device 160x64
[ 9.929141] fb0: nouveaufb frame buffer device
[ 9.929142] drm: registered panic notifier
[ 9.929149] [drm] Initialized nouveau 0.0.16 20090420 for 0000:01:00.0 on
minor 0
[ 6.222571] [drm] Initialized drm 1.1.0 20060810
[ 6.558162] nouveau 0000:01:00.0: PCI INT A -> Link[APC3] -> GSI 18 (level,
low) -> IRQ 18
[ 6.558167] nouveau 0000:01:00.0: setting latency timer to 64
[ 6.561069] [drm] nouveau 0000:01:00.0: Detected an NV40 generation card
(0x044100a2)
[ 6.561602] [drm] nouveau 0000:01:00.0: Attempting to load BIOS image from
PROM
[ 6.764616] [drm] nouveau 0000:01:00.0: ... appears to be valid
[ 6.764619] [drm] nouveau 0000:01:00.0: BIT BIOS found
[ 6.764622] [drm] nouveau 0000:01:00.0: Bios version 05.44.02.11
[ 6.764626] [drm] nouveau 0000:01:00.0: BIT table 'd' not found
[ 6.764629] [drm] nouveau 0000:01:00.0: Found Display Configuration Block
version 3.0
[ 6.764632] [drm] nouveau 0000:01:00.0: DCB connector table: VHER 0x30 5 6 2
[ 6.764635] [drm] nouveau 0000:01:00.0: Raw DCB entry 0: 01010310 00000028
[ 6.764638] [drm] nouveau 0000:01:00.0: Raw DCB entry 1: 01000302 00000000
[ 6.764641] [drm] nouveau 0000:01:00.0: Raw DCB entry 2: 020203f1 0000c020
[ 6.764648] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 0 at offset
0xEBC4
[ 6.764809] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 1 at offset
0xEE99
[ 6.824227] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 2 at offset
0xF2D1
[ 6.824255] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 3 at offset
0xF42E
[ 6.832139] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 4 at offset
0xF4DC
[ 6.842099] [TTM] Zone kernel: Available graphics memory: 431048 kiB.
[ 6.842103] [TTM] Zone highmem: Available graphics memory: 2073516 kiB.
[ 6.842116] [drm] nouveau 0000:01:00.0: 16 MiB VRAM
[ 6.843506] [drm] nouveau 0000:01:00.0: 64 MiB GART (aperture)
[ 6.844031] [drm] nouveau 0000:01:00.0: Allocating FIFO number 0
[ 6.844508] [drm] nouveau 0000:01:00.0: nouveau_channel_alloc: initialised
FIFO 0
[ 6.844514] [drm] nouveau 0000:01:00.0: Initial CRTC_OWNER is 0
[ 6.844521] [drm] nouveau 0000:01:00.0: Saving VGA fonts
[ 6.904053] [drm] nouveau 0000:01:00.0: Detected a VGA connector
[ 6.904111] [drm] nouveau 0000:01:00.0: Detected a DVI-D connector
[ 6.904135] [drm] nouveau 0000:01:00.0: Detected a TV connector
[ 6.905838] [drm] nouveau 0000:01:00.0: Setting dpms mode 3 on vga encoder
(output 0)
[ 6.905842] [drm] nouveau 0000:01:00.0: Setting dpms mode 3 on tmds encoder
(output 1)
[ 6.905845] [drm] nouveau 0000:01:00.0: Setting dpms mode 3 on TV encoder
(output 2)
[ 7.091607] [drm] nouveau 0000:01:00.0: allocated 1600x1200 fb: 0x49000, bo
f70c8e00
[ 7.102983] [drm] nouveau 0000:01:00.0: Output DVI-D-1 is running on CRTC 0
using output A
[ 7.102987] [drm] nouveau 0000:01:00.0: 0xD149: Parsing digital output
script table
[ 7.157026] [drm] nouveau 0000:01:00.0: Setting dpms mode 0 on tmds encoder
(output 1)
[ 7.157031] [drm] nouveau 0000:01:00.0: Output DVI-D-1 is running on CRTC 0
using output A
[ 7.163921] Console: switching to colour frame buffer device 200x75
[ 7.172091] fb0: nouveaufb frame buffer device
[ 7.172093] registered panic notifier
[ 7.172101] [drm] Initialized nouveau 0.0.15 20090420 for 0000:01:00.0 on
minor 0
--- End Message ---
