Your message dated Sat, 8 Jun 2013 12:17:54 +0200
with message-id <20130608101754.GG4796@pisco.westfalen.local>
and subject line Closing
has caused the Debian Bug report #601723,
regarding linux-image-2.6.32-5-686: /proc/net/dev report incorrect bytes number
(both TX and RX)
to be marked as done.
This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.
(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact ow...@bugs.debian.org
immediately.)
--
601723: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=601723
Debian Bug Tracking System
Contact ow...@bugs.debian.org with problems
--- Begin Message ---
Package: linux-2.6
Version: 2.6.32-26
Severity: normal
I've downloaded around 600 GB of data round this week and ifconfig(8)
was still reporting completly unrealistic figures. /proc/net/dev is
consistent with ifconfig figures.
-- Package-specific info:
** Version:
Linux version 2.6.32-5-686 (Debian 2.6.32-25) (da...@debian.org) (gcc version
4.3.5 (Debian 4.3.5-4) ) #1 SMP Thu Oct 14 17:15:16 UTC 2010
** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-686
root=UUID=2e624958-cf94-4b06-8c69-69fbed9a22c4 ro quiet
** Not tainted
** Kernel log:
[ 1.175672] ACPI: PCI Interrupt Link [LUSB] enabled at IRQ 10
[ 1.175687] ohci_hcd 0000:00:0f.2: PCI INT A -> Link[LUSB] -> GSI 10 (level,
low) -> IRQ 10
[ 1.175714] ohci_hcd 0000:00:0f.2: OHCI Host Controller
[ 1.175749] ohci_hcd 0000:00:0f.2: new USB bus registered, assigned bus
number 1
[ 1.175783] ohci_hcd 0000:00:0f.2: irq 10, io mem 0xfe100000
[ 1.230037] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.230043] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.230046] usb usb1: Product: OHCI Host Controller
[ 1.230049] usb usb1: Manufacturer: Linux 2.6.32-5-686 ohci_hcd
[ 1.230052] usb usb1: SerialNumber: 0000:00:0f.2
[ 1.230251] usb usb1: configuration #1 chosen from 1 choice
[ 1.230337] hub 1-0:1.0: USB hub found
[ 1.230353] hub 1-0:1.0: 4 ports detected
[ 1.230433] pata_sil680 0000:00:05.0: version 0.4.9
[ 1.230459] pata_sil680 0000:00:05.0: PCI INT A -> GSI 23 (level, low) ->
IRQ 23
[ 1.230481] sil680: 133MHz clock.
[ 1.232723] scsi0 : pata_sil680
[ 1.233639] scsi1 : pata_sil680
[ 1.233720] ata1: PATA max UDMA/133 cmd 0xece8 ctl 0xecf4 bmdma 0xecb0 irq 23
[ 1.233726] ata2: PATA max UDMA/133 cmd 0xecd0 ctl 0xecdc bmdma 0xecb8 irq 23
[ 1.235137] scsi2 : pata_serverworks
[ 1.236936] scsi3 : pata_serverworks
[ 1.237020] ata3: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x8b0 irq 14
[ 1.237024] ata4: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x8b8 irq 15
[ 1.237233] sata_sil 0000:00:03.0: version 2.4
[ 1.237294] sata_sil 0000:00:03.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 1.237760] scsi4 : sata_sil
[ 1.237939] scsi5 : sata_sil
[ 1.237989] ata5: SATA max UDMA/100 mmio m512@0xfe102400 tf 0xfe102480 irq 17
[ 1.237994] ata6: SATA max UDMA/100 mmio m512@0xfe102400 tf 0xfe1024c0 irq 17
[ 1.408301] ata3.00: ATAPI: TEAC CD-ROM CD-224E, K.9A, max UDMA/33
[ 1.424312] ata3.00: configured for UDMA/33
[ 1.556032] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1.569705] scsi 2:0:0:0: CD-ROM TEAC CD-224E K.9A
PQ: 0 ANSI: 5
[ 1.574782] ata5.00: ATA-8: WDC WD2001FASS-00W2B0, 01.00101, max UDMA/133
[ 1.574788] ata5.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 1.581163] ata5.00: configured for UDMA/100
[ 1.735440] scsi 4:0:0:0: Direct-Access ATA WDC WD2001FASS-0 01.0
PQ: 0 ANSI: 5
[ 2.052023] ata6: SATA link down (SStatus 0 SControl 310)
[ 2.075438] sd 4:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00
TB/1.81 TiB)
[ 2.075505] sd 4:0:0:0: [sda] Write Protect is off
[ 2.075509] sd 4:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.075537] sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 2.075714] sda:sr0: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray
[ 2.081298] Uniform CD-ROM driver Revision: 3.20
[ 2.081804] sr 2:0:0:0: Attached scsi CD-ROM sr0
[ 2.104691] sda1 sda2 sda3
[ 2.105593] sd 4:0:0:0: [sda] Attached SCSI disk
[ 2.123413] sr 2:0:0:0: Attached scsi generic sg0 type 5
[ 2.124272] sd 4:0:0:0: Attached scsi generic sg1 type 0
[ 2.307398] PM: Starting manual resume from disk
[ 2.307405] PM: Resume from partition 8:3
[ 2.307407] PM: Checking hibernation image.
[ 2.307631] PM: Error -22 checking image file
[ 2.307634] PM: Resume from disk failed.
[ 2.350903] EXT3-fs: INFO: recovery required on readonly filesystem.
[ 2.350909] EXT3-fs: write access will be enabled during recovery.
[ 8.616736] kjournald starting. Commit interval 5 seconds
[ 8.616765] EXT3-fs: sda2: orphan cleanup on readonly fs
[ 8.632820] ext3_orphan_cleanup: deleting unreferenced inode 108470387
[ 8.640802] EXT3-fs: sda2: 1 orphan inode deleted
[ 8.640805] EXT3-fs: recovery complete.
[ 8.658610] EXT3-fs: mounted filesystem with ordered data mode.
[ 9.765861] udev: starting version 160
[ 10.107819] input: PC Speaker as /devices/platform/pcspkr/input/input1
[ 10.201499] input: Power Button as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 10.201510] ACPI: Power Button [PWRF]
[ 10.203251] processor LNXCPU:00: registered as cooling_device0
[ 10.446095] dcdbas dcdbas: Dell Systems Management Base Driver (version
5.6.0-3.2)
[ 10.601516] piix4_smbus 0000:00:0f.0: Host SMBus controller not enabled!
[ 10.735491] Error: Driver 'pcspkr' is already registered, aborting...
[ 11.097524] input: PS/2 Logitech Mouse as
/devices/platform/i8042/serio1/input/input3
[ 11.200806] Adding 1509656k swap on /dev/sda3. Priority:-1 extents:1
across:1509656k
[ 11.339225] EXT3 FS on sda2, internal journal
[ 11.463953] loop: module loaded
[ 12.548482] r8169: eth0: link up
[ 23.528025] eth0: no IPv6 routers present
[ 1752.231699] i2c /dev entries driver
[ 1992.283745] Uhhuh. NMI received for unknown reason 31 on CPU 0.
[ 1992.283776] Do you have a strange power saving mode enabled?
[ 1992.283800] Dazed and confused, but trying to continue
[ 2316.697564] process `sysctl' is using deprecated sysctl (syscall)
net.ipv6.neigh.default.retrans_time; Use net.ipv6.neigh.default.retrans_time_ms
instead.
[64273.679071] udev[6496]: starting version 163
[64297.495193] SGI XFS with ACLs, security attributes, realtime, large
block/inode numbers, no debug enabled
[64297.497303] SGI XFS Quota Management subsystem
[64297.506446] JFS: nTxBlock = 4020, nTxLock = 32161
[64297.535077] NTFS driver 2.1.29 [Flags: R/W MODULE].
[64297.557360] QNX4 filesystem 0.2.3 registered.
[64297.587669] Btrfs loaded
[79877.278405] RPC: Registered udp transport module.
[79877.278410] RPC: Registered tcp transport module.
[79877.278413] RPC: Registered tcp NFSv4.1 backchannel transport module.
[79877.363299] Installing knfsd (copyright (C) 1996 o...@monad.swb.de).
[79877.449382] svc: failed to register lockdv1 RPC service (errno 97).
[79877.450712] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery
directory
[79877.450950] NFSD: starting 90-second grace period
[80002.904365] nfsd: last server has exited, flushing export cache
[80004.245501] svc: failed to register lockdv1 RPC service (errno 97).
[80004.246819] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery
directory
[80004.247034] NFSD: starting 90-second grace period
** Model information
not available
** Loaded modules:
Module Size Used by
nfsd 192415 11
lockd 49301 1 nfsd
nfs_acl 1695 1 nfsd
auth_rpcgss 25200 1 nfsd
sunrpc 134116 10 nfsd,lockd,nfs_acl,auth_rpcgss
exportfs 2586 1 nfsd
crc32c 2172 0
ext4 257163 0
jbd2 55931 1 ext4
crc16 1027 1 ext4
ext2 46157 0
i2c_dev 3505 0
loop 9729 0
snd_pcm 47226 0
snd_timer 12258 1 snd_pcm
psmouse 44621 0
i2c_piix4 7076 0
snd 34339 2 snd_pcm,snd_timer
dcdbas 3860 0
i2c_core 12660 2 i2c_dev,i2c_piix4
soundcore 3450 1 snd
evdev 5609 2
snd_page_alloc 4977 1 snd_pcm
serio_raw 2916 0
button 3598 0
processor 26603 0
pcspkr 1207 0
ext3 93832 1
jbd 31965 1 ext3
mbcache 3762 3 ext4,ext2,ext3
sg 15936 0
sr_mod 10770 0
sd_mod 25801 3
crc_t10dif 1012 1 sd_mod
cdrom 26487 1 sr_mod
ata_generic 2019 0
sata_sil 5620 2
pata_serverworks 3933 0
pata_sil680 3281 0
ohci_hcd 16776 0
ehci_hcd 27615 0
libata 115517 4
ata_generic,sata_sil,pata_serverworks,pata_sil680
thermal 9206 0
usbcore 98185 3 ohci_hcd,ehci_hcd
floppy 40923 0
r8169 24716 0
mii 2714 1 r8169
nls_base 4541 1 usbcore
thermal_sys 9378 2 processor,thermal
scsi_mod 101169 4 sg,sr_mod,sd_mod,libata
** PCI devices:
00:00.0 Host bridge [0600]: Broadcom GCNB-LE Host Bridge [1166:0017] (rev 32)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:00.1 Host bridge [0600]: Broadcom GCNB-LE Host Bridge [1166:0017]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:03.0 Mass storage controller [0180]: Silicon Image, Inc. SiI 3512
[SATALink/SATARaid] Serial ATA Controller [1095:3512] (rev 01)
Subsystem: Silicon Image, Inc. SiI 3512 SATALink Controller [1095:3512]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at ecf8 [size=8]
Region 1: I/O ports at ecf0 [size=4]
Region 2: I/O ports at ece0 [size=8]
Region 3: I/O ports at ecd8 [size=4]
Region 4: I/O ports at ecc0 [size=16]
Region 5: Memory at fe102400 (32-bit, non-prefetchable) [size=512]
Expansion ROM at fe000000 [disabled] [size=512K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: sata_sil
00:04.0 VGA compatible controller [0300]: ATI Technologies Inc Rage XL
[1002:4752] (rev 27) (prog-if 00 [VGA controller])
Subsystem: Dell Device [1028:0141]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr-
Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2000ns min), Cache Line Size: 64 bytes
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at e800 [size=256]
Region 2: Memory at fe101000 (32-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at 20080000 [disabled] [size=128K]
Capabilities: [5c] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
00:05.0 IDE interface [0101]: Silicon Image, Inc. PCI0680 Ultra ATA-133 Host
Controller [1095:0680] (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: Dell Device [1028:0141]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 23
Region 0: I/O ports at ece8 [size=8]
Region 1: I/O ports at ecf4 [size=4]
Region 2: I/O ports at ecd0 [size=8]
Region 3: I/O ports at ecdc [size=4]
Region 4: I/O ports at ecb0 [size=16]
Region 5: Memory at fe102000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at 20000000 [disabled] [size=512K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: pata_sil680
00:0f.0 Host bridge [0600]: Broadcom CSB6 South Bridge [1166:0203] (rev a0)
Subsystem: Broadcom Device [1166:0201]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 32
00:0f.1 IDE interface [0101]: Broadcom CSB6 RAID/IDE Controller [1166:0213]
(rev a0) (prog-if 8a [Master SecP PriP])
Subsystem: Dell Device [1028:0141]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 08b0 [size=16]
Kernel driver in use: pata_serverworks
00:0f.2 USB Controller [0c03]: Broadcom CSB6 OHCI USB Controller [1166:0221]
(rev 05) (prog-if 10 [OHCI])
Subsystem: Broadcom Device [1166:0220]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (20000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fe100000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:0f.3 ISA bridge [0601]: Broadcom GCLE-2 Host Bridge [1166:0227]
Subsystem: Broadcom Device [1166:0230]
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:10.0 Host bridge [0600]: Broadcom CIOB-E I/O Bridge with Gigabit Ethernet
[1166:0110] (rev 12)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR+ INTx-
Capabilities: [60] PCI-X non-bridge device
Command: DPERE- ERO- RBC=512 OST=8
Status: Dev=00:00.0 64bit+ 133MHz+ SCD- USC- DC=bridge
DMMRBC=512 DMOST=8 DMCRS=8 RSCEM- 266MHz- 533MHz-
00:10.2 Host bridge [0600]: Broadcom CIOB-E I/O Bridge with Gigabit Ethernet
[1166:0110] (rev 12)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
Capabilities: [60] PCI-X non-bridge device
Command: DPERE- ERO- RBC=512 OST=8
Status: Dev=00:00.0 64bit+ 133MHz+ SCD- USC- DC=bridge
DMMRBC=512 DMOST=8 DMCRS=8 RSCEM- 266MHz- 533MHz-
01:03.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8169
Gigabit Ethernet [10ec:8169] (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet
[10ec:8169]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at dc00 [size=256]
Region 1: Memory at fcf00000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at fce00000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: r8169
** USB devices:
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
-- System Information:
Debian Release: squeeze/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 2.6.32-5-686 (SMP w/1 CPU core)
Locale: LANG=fr_FR.UTF-8, LC_CTYPE=fr_FR.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.32-5-686 depends on:
ii debconf [debconf-2.0] 1.5.36 Debian configuration management sy
ii initramfs-tools [linux-initra 0.98.5 tools for generating an initramfs
ii linux-base 2.6.32-26 Linux image base package
ii module-init-tools 3.12-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.32-5-686 recommends:
ii firmware-linux-free 2.6.32-26 Binary firmware for various driver
ii libc6-i686 2.11.2-6+squeeze1 Embedded GNU C Library: Shared lib
Versions of packages linux-image-2.6.32-5-686 suggests:
pn grub | lilo <none> (no description available)
pn linux-doc-2.6.32 <none> (no description available)
Versions of packages linux-image-2.6.32-5-686 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
ii firmware-linux 0.27 Binary firmware for various driver
ii firmware-linux-nonfree 0.27 Binary firmware for various driver
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information:
linux-image-2.6.32-5-686/prerm/removing-running-kernel-2.6.32-5-686: true
linux-image-2.6.32-5-686/postinst/depmod-error-initrd-2.6.32-5-686: false
linux-image-2.6.32-5-686/postinst/ignoring-do-bootloader-2.6.32-5-686:
linux-image-2.6.32-5-686/postinst/missing-firmware-2.6.32-5-686:
--- End Message ---
--- Begin Message ---
Hi,
your bug has been filed against the "linux-2.6" source package and was filed for
a kernel older than the recently released Debian 7.0 / Wheezy with a severity
less than important.
We don't have the ressources to reproduce the complete backlog of all older
kernel
bugs, so we're closing this bug for now. If you can reproduce the bug with
Debian Wheezy
or a more recent kernel from testing or unstable, please reopen the bug by
sending
a mail to cont...@bugs.debian.org with the following three commands included in
the
mail:
reopen BUGNUMBER
reassign BUGNUMBER src:linux
thanks
Cheers,
Moritz
--- End Message ---
