--- Begin Message ---
Package: linux-2.6
Version: 2.6.32-5
Severity: normal
Hi!
There is a Speeddragon PCI card NEC chip 4 +1 port. Layered on
Delock(Jmicron) USB-> SATA adapter and I get the following error :
usb 2-2: new high speed USB device using ehci_hcd and address 2
[ 1.464965] usb 2-2: New USB device found, idVendor=152d, idProduct=2329
[ 1.464970] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 1.464974] usb 2-2: Product: USB to ATA/ATAPI Bridge
[ 1.464977] usb 2-2: Manufacturer: JMicron
[ 1.464979] usb 2-2: SerialNumber: 08871F418665
[ 1.465132] usb 2-2: configuration #1 chosen from 1 choice
[ 1.475533] Initializing USB Mass Storage driver...
[ 1.475717] scsi1 : SCSI emulation for USB Mass Storage devices
[ 1.475898] usb-storage: device found at 2
[ 1.475902] usb-storage: waiting for device to settle before scanning
[ 1.475921] usbcore: registered new interface driver usb-storage
[ 1.475975] USB Mass Storage support registered.
scsi 1:0:0:0: Direct-Access SAMSUNG SP1213C PQ: 0 ANSI: 2 CCS
[ 6.482633] sd 1:0:0:0: [sda] 234493056 512-byte logical blocks: (120 GB/111
GiB)
[ 6.483377] sd 1:0:0:0: [sda] Write Protect is off
[ 6.483382] sd 1:0:0:0: [sda] Mode Sense: 34 00 00 00
[ 6.483385] sd 1:0:0:0: [sda] Assuming drive cache: write through
[ 6.484876] sd 1:0:0:0: [sda] Assuming drive cache: write through
[ 6.484937] sda:
[ 6.604028] usb 2-2: reset high speed USB device using ehci_hcd and address 2
[ 6.716023] usb 2-2: device descriptor read/64, error -32
[ 6.932025] usb 2-2: device descriptor read/64, error -32
[ 7.148025] usb 2-2: reset high speed USB device using ehci_hcd and address 2
[ 7.260020] usb 2-2: device descriptor read/64, error -32
[ 7.476022] usb 2-2: device descriptor read/64, error -32
[ 7.692025] usb 2-2: reset high speed USB device using ehci_hcd and address 2
[ 7.724282] usb 2-2: device descriptor read/8, error -71
[ 7.858758] usb 2-2: device descriptor read/8, error -71
usb 2-2: USB disconnect, address 2
[ 8.340100] sd 1:0:0:0: [sda] Unhandled error code
[ 8.340105] sd 1:0:0:0: [sda] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 8.340110] sd 1:0:0:0: [sda] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00
[ 8.340124] end_request: I/O error, dev sda, sector 0
[ 8.340177] Buffer I/O error on device sda, logical block 0
[ 8.340302] ldm_validate_partition_table(): Disk read failed.
[ 8.340393] Dev sda: unable to read RDB block 0
[ 8.340449] unable to read partition table
[ 8.340770] sd 1:0:0:0: [sda] READ CAPACITY failed
[ 8.340776] sd 1:0:0:0: [sda] Result: hostbyte=DID_NO_CONNECT
driverbyte=DRIVER_OK
[ 8.340783] sd 1:0:0:0: [sda] Sense not available.
sd 1:0:0:0: [sda] Write Protect is on
[ 8.340826] sd 1:0:0:0: [sda] Mode Sense: 33 c0 8e d0
[ 8.340829] sd 1:0:0:0: [sda] Assuming drive cache: write through
[ 8.340878] sd 1:0:0:0: [sda] Attached SCSI disk
[ 8.473020] usb 2-2: new high speed USB device using ehci_hcd and address 3
[ 8.584024] usb 2-2: device descriptor read/64, error -32
[ 8.808034] usb 2-2: device descriptor read/64, error -32
but
I put an external USB hub for this
through the mount can be (this is a motherboard from a USB-connected).
What's the trouble with PCI usb's?
(So you can find, looks at the SATA, and then stop).
Thanks
-- Package-specific info:
** Version:
Linux version 2.6.32-trunk-amd64 (Debian 2.6.32-5) (b...@decadent.org.uk) (gcc
version 4.3.4 (Debian 4.3.4-6) ) #1 SMP Sun Jan 10 22:40:40 UTC 2010
** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.32-trunk-amd64
root=UUID=40c44e8c-9cd0-40c4-92ce-bdf099a32dd8 ro quiet
** Not tainted
** Kernel log:
[ 21.410924] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 21.417457] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 21.470647] intel_rng: FWH not detected
[ 21.497011] parport_pc 00:0a: reported by Plug and Play ACPI
[ 21.497130] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
[ 21.499846] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 21.544764] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 17 (level, low) -> IRQ
17
[ 21.578837] EDAC MC: Ver: 2.1.0 Jan 10 2010
[ 21.625359] Contact your BIOS vendor to see if the E752x error registers can
be safely un-hidden
[ 22.271058] Adding 2714944k swap on /dev/sda5. Priority:-1 extents:1
across:2714944k
[ 22.403261] EXT3 FS on sda1, internal journal
[ 22.467853] loop: module loaded
[ 22.959096] kjournald starting. Commit interval 5 seconds
[ 22.970181] EXT3 FS on sda6, internal journal
[ 22.970190] EXT3-fs: mounted filesystem with ordered data mode.
[ 23.663356] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 23.892082] fuse init (API version 7.13)
[ 25.313729] tg3: eth0: Link is up at 100 Mbps, full duplex.
[ 25.313735] tg3: eth0: Flow control is on for TX and on for RX.
[ 25.313920] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 27.334757] NET: Registered protocol family 5
[ 28.115514] Bluetooth: Core ver 2.15
[ 28.115607] NET: Registered protocol family 31
[ 28.115610] Bluetooth: HCI device and connection manager initialized
[ 28.115615] Bluetooth: HCI socket layer initialized
[ 28.133575] Bluetooth: L2CAP ver 2.14
[ 28.133579] Bluetooth: L2CAP socket layer initialized
[ 28.154887] Bluetooth: RFCOMM TTY layer initialized
[ 28.154894] Bluetooth: RFCOMM socket layer initialized
[ 28.154897] Bluetooth: RFCOMM ver 1.11
[ 28.235646] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 28.235652] Bluetooth: BNEP filters: protocol multicast
[ 28.246486] Bridge firewalling registered
[ 28.287617] Bluetooth: SCO (Voice Link) ver 0.6
[ 28.287623] Bluetooth: SCO socket layer initialized
[ 29.104088] lp0: using parport0 (interrupt-driven).
[ 29.156937] ppdev: user-space parallel port driver
[ 29.839996] RPC: Registered udp transport module.
[ 29.840002] RPC: Registered tcp transport module.
[ 29.840006] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 29.900837] Installing knfsd (copyright (C) 1996 o...@monad.swb.de).
[ 35.724019] eth0: no IPv6 routers present
[ 129.456021] usb 4-1: new full speed USB device using ohci_hcd and address 6
[ 129.636017] usb 4-1: device descriptor read/64, error -32
[ 129.920020] usb 4-1: device descriptor read/64, error -32
[ 130.200017] usb 4-1: new full speed USB device using ohci_hcd and address 7
[ 130.380018] usb 4-1: device descriptor read/64, error -32
[ 130.664021] usb 4-1: device descriptor read/64, error -32
[ 130.944020] usb 4-1: new full speed USB device using ohci_hcd and address 8
[ 130.971742] usb 4-1: device descriptor read/8, error -62
[ 131.095720] usb 4-1: device descriptor read/8, error -62
[ 131.372018] usb 4-1: new full speed USB device using ohci_hcd and address 9
[ 131.399669] usb 4-1: device descriptor read/8, error -62
[ 131.523649] usb 4-1: device descriptor read/8, error -62
[ 131.624021] hub 4-0:1.0: unable to enumerate USB device on port 1
[ 131.860686] CPU0 attaching NULL sched-domain.
[ 131.860694] CPU1 attaching NULL sched-domain.
[ 131.860698] CPU2 attaching NULL sched-domain.
[ 131.860701] CPU3 attaching NULL sched-domain.
[ 131.888130] CPU0 attaching sched-domain:
[ 131.888136] domain 0: span 0,2 level SIBLING
[ 131.888140] groups: 0 (cpu_power = 589) 2 (cpu_power = 589)
[ 131.888150] domain 1: span 0,2 level MC
[ 131.888153] groups: 0,2 (cpu_power = 1178)
[ 131.888161] domain 2: span 0-3 level CPU
[ 131.888164] groups: 0,2 (cpu_power = 1178) 1,3 (cpu_power = 1178)
[ 131.888174] CPU1 attaching sched-domain:
[ 131.888177] domain 0: span 1,3 level SIBLING
[ 131.888180] groups: 1 (cpu_power = 589) 3 (cpu_power = 589)
[ 131.888189] domain 1: span 1,3 level MC
[ 131.888192] groups: 1,3 (cpu_power = 1178)
[ 131.888198] domain 2: span 0-3 level CPU
[ 131.888201] groups: 1,3 (cpu_power = 1178) 0,2 (cpu_power = 1178)
[ 131.888211] CPU2 attaching sched-domain:
[ 131.888214] domain 0: span 0,2 level SIBLING
[ 131.888217] groups: 2 (cpu_power = 589) 0 (cpu_power = 589)
[ 131.888226] domain 1: span 0,2 level MC
[ 131.888229] groups: 0,2 (cpu_power = 1178)
[ 131.888235] domain 2: span 0-3 level CPU
[ 131.888238] groups: 0,2 (cpu_power = 1178) 1,3 (cpu_power = 1178)
[ 131.888248] CPU3 attaching sched-domain:
[ 131.888251] domain 0: span 1,3 level SIBLING
[ 131.888254] groups: 3 (cpu_power = 589) 1 (cpu_power = 589)
[ 131.888262] domain 1: span 1,3 level MC
[ 131.888265] groups: 1,3 (cpu_power = 1178)
[ 131.888271] domain 2: span 0-3 level CPU
[ 131.888275] groups: 1,3 (cpu_power = 1178) 0,2 (cpu_power = 1178)
[ 1647.360033] usb 4-1: new full speed USB device using ohci_hcd and address 10
[ 1647.540046] usb 4-1: device descriptor read/64, error -32
[ 1647.824030] usb 4-1: device descriptor read/64, error -32
[ 1648.104045] usb 4-1: new full speed USB device using ohci_hcd and address 11
[ 1648.284020] usb 4-1: device descriptor read/64, error -32
[ 1648.568019] usb 4-1: device descriptor read/64, error -32
[ 1648.848027] usb 4-1: new full speed USB device using ohci_hcd and address 12
[ 1648.875743] usb 4-1: device descriptor read/8, error -62
[ 1648.999722] usb 4-1: device descriptor read/8, error -62
[ 1649.277516] usb 4-1: new full speed USB device using ohci_hcd and address 13
[ 1649.304674] usb 4-1: device descriptor read/8, error -62
[ 1649.427651] usb 4-1: device descriptor read/8, error -62
[ 1649.528027] hub 4-0:1.0: unable to enumerate USB device on port 1
** Model information
sys_vendor: HP
product_name: ProLiant ML150 G2
product_version: N/A
chassis_vendor: HP
chassis_version: N/A
bios_vendor: HP
bios_version: 1.57
board_vendor: Intel
board_name: Nocona/Lindenhurst-VS/Hance Rapid
board_version: To Be Filled By HP
** Loaded modules:
Module Size Used by
nfsd 253670 1
lockd 57523 1 nfsd
nfs_acl 2031 1 nfsd
auth_rpcgss 33300 1 nfsd
sunrpc 161057 4 nfsd,lockd,nfs_acl,auth_rpcgss
exportfs 3170 1 nfsd
ppdev 5030 0
lp 7462 0
sco 7193 2
bridge 39582 0
stp 1440 1 bridge
bnep 9395 2
rfcomm 29501 0
l2cap 24656 6 bnep,rfcomm
crc16 1319 1 l2cap
bluetooth 41795 6 sco,bnep,rfcomm,l2cap
rfkill 12996 3 bluetooth
appletalk 24133 0
cpufreq_conservative 5162 0
cpufreq_userspace 1992 0
cpufreq_powersave 902 0
cpufreq_stats 2659 0
binfmt_misc 6431 1
fuse 50078 1
loop 11767 0
e752x_edac 9393 0
edac_core 29245 1 e752x_edac
i2c_i801 7766 0
container 2389 0
i2c_core 15584 1 i2c_i801
shpchp 25928 0
parport_pc 18839 1
rng_core 2990 0
serio_raw 3752 0
pcspkr 1699 0
parport 27938 3 ppdev,lp,parport_pc
pci_hotplug 21171 1 shpchp
evdev 7336 11
psmouse 49521 0
processor 29479 0
ext3 106454 2
jbd 37037 1 ext3
mbcache 4970 1 ext3
sd_mod 29673 4
crc_t10dif 1276 1 sd_mod
usbhid 31196 0
hid 62745 1 usbhid
ide_cd_mod 24744 0
cdrom 29399 1 ide_cd_mod
ide_pci_generic 2788 0
ata_generic 2983 0
libata 131655 1 ata_generic
usb_storage 38585 0
ohci_hcd 19196 0
aic7xxx 107123 3
uhci_hcd 18457 0
scsi_transport_spi 18774 1 aic7xxx
piix 4568 0
ide_core 76802 3 ide_cd_mod,ide_pci_generic,piix
scsi_mod 121909 5
sd_mod,libata,usb_storage,aic7xxx,scsi_transport_spi
floppy 49087 0
ehci_hcd 30578 0
tg3 95535 0
libphy 13542 1 tg3
usbcore 121687 6 usbhid,usb_storage,ohci_hcd,uhci_hcd,ehci_hcd
nls_base 6377 1 usbcore
button 4634 0
thermal 11674 0
fan 3346 0
thermal_sys 11878 3 processor,thermal,fan
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
allow-hotplug eth0
iface eth0 inet dhcp
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
link/ether 00:11:85:af:32:82 brd ff:ff:ff:ff:ff:ff
inet 192.168.1.84/24 brd 192.168.1.255 scope global eth0
inet6 fe80::211:85ff:feaf:3282/64 scope link
valid_lft forever preferred_lft forever
3: pan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN
link/ether 3a:be:8c:07:f4:86 brd ff:ff:ff:ff:ff:ff
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes
packets errs drop fifo colls carrier compressed
lo: 5202 54 0 0 0 0 0 0 5202
54 0 0 0 0 0 0
eth0: 1488025 1426 0 0 0 0 0 17 148792
1363 0 0 0 0 0 0
pan0: 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0
*** Protocol statistics:
Ip:
1454 total packets received
0 forwarded
0 incoming packets discarded
1454 incoming packets delivered
1309 requests sent out
12 dropped because of missing route
Icmp:
9 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
destination unreachable: 3
echo replies: 6
9 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
destination unreachable: 3
echo request: 6
IcmpMsg:
InType0: 6
InType3: 3
OutType3: 3
OutType8: 6
Tcp:
69 active connections openings
5 passive connection openings
0 failed connection attempts
5 connection resets received
0 connections established
1340 segments received
1191 segments send out
0 segments retransmited
0 bad segments received.
8 resets sent
Udp:
124 packets received
3 packets to unknown port received.
0 packet receive errors
130 packets sent
UdpLite:
TcpExt:
15 TCP sockets finished time wait in fast timer
60 delayed acks sent
856 packet headers predicted
111 acknowledgments not containing data payload received
5 connections reset due to unexpected data
IpExt:
InMcastPkts: 53
OutMcastPkts: 55
InBcastPkts: 2
InOctets: 1467094
OutOctets: 118071
InMcastOctets: 5249
OutMcastOctets: 5397
InBcastOctets: 1152
*** Device features:
eth0: 0x109a3
lo: 0x13865
pan0: 0xff3865
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation E7320 Memory Controller Hub
[8086:3592] (rev 0c)
Subsystem: Intel Corporation E7320 Memory Controller Hub [8086:3592]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:02.0 PCI bridge [0604]: Intel Corporation E7525/E7520/E7320 PCI Express Port
A [8086:3595] (rev 0c) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:03.0 PCI bridge [0604]: Intel Corporation E7525/E7520/E7320 PCI Express Port
A1 [8086:3596] (rev 0c) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Memory behind bridge: dd100000-dd1fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.0 PCI bridge [0604]: Intel Corporation 6300ESB 64-bit PCI-X Bridge
[8086:25ae] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 48, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=48
I/O behind bridge: 00002000-00002fff
Memory behind bridge: dd200000-dd2fffff
Prefetchable memory behind bridge: 0000000040000000-00000000400fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1d.0 USB Controller [0c03]: Intel Corporation 6300ESB USB Universal Host
Controller [8086:25a9] (rev 02) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:25a1]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at 1400 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 6300ESB USB Universal Host
Controller [8086:25aa] (rev 02) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:25a1]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 1420 [size=32]
Kernel driver in use: uhci_hcd
00:1d.4 System peripheral [0880]: Intel Corporation 6300ESB Watchdog Timer
[8086:25ab] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:0000]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: Memory at dd001000 (32-bit, non-prefetchable) [size=16]
00:1d.5 PIC [0800]: Intel Corporation 6300ESB I/O Advanced Programmable
Interrupt Controller [8086:25ac] (rev 02) (prog-if 20 [IO(X)-APIC])
Subsystem: Intel Corporation Device [8086:25a1]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1d.7 USB Controller [0c03]: Intel Corporation 6300ESB USB2 Enhanced Host
Controller [8086:25ad] (rev 02) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Device [103c:24d0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 0: Memory at dd001400 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev
0a) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=64
I/O behind bridge: 00003000-00003fff
Memory behind bridge: dd300000-deffffff
Prefetchable memory behind bridge: 40100000-401fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:1f.0 ISA bridge [0601]: Intel Corporation 6300ESB LPC Interface Controller
[8086:25a1] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:1f.1 IDE interface [0101]: Intel Corporation 6300ESB PATA Storage Controller
[8086:25a2] (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Hewlett-Packard Company Device [103c:25a1]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 1440 [size=16]
Region 5: Memory at 40200000 (32-bit, non-prefetchable) [size=1K]
Kernel driver in use: PIIX_IDE
00:1f.3 SMBus [0c05]: Intel Corporation 6300ESB SMBus Controller [8086:25a4]
(rev 02)
Subsystem: Hewlett-Packard Company Device [103c:25a1]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 1100 [size=32]
Kernel driver in use: i801_smbus
02:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5721
Gigabit Ethernet PCI Express [14e4:1659] (rev 11)
Subsystem: Hewlett-Packard Company Device [103c:3260]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at dd100000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <ignored> [disabled]
Capabilities: <access denied>
Kernel driver in use: tg3
03:01.0 SCSI storage controller [0100]: Adaptec AIC-7892A U160/m [9005:0080]
(rev 02)
Subsystem: Adaptec 29160LP Low Profile Ultra160 SCSI Controller
[9005:e220]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 72 (10000ns min, 6250ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 24
BIST result: 00
Region 0: I/O ports at 2000 [disabled] [size=256]
Region 1: Memory at dd200000 (64-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at 40000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: aic7xxx
04:01.0 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 43)
(prog-if 10 [OHCI])
Subsystem: NEC Corporation Hama USB 2.0 CardBus [1033:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (250ns min, 10500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at dd300000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
04:01.1 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 43)
(prog-if 10 [OHCI])
Subsystem: NEC Corporation Hama USB 2.0 CardBus [1033:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (250ns min, 10500ns max), Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at dd301000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
04:01.2 USB Controller [0c03]: NEC Corporation USB 2.0 [1033:00e0] (rev 04)
(prog-if 20 [EHCI])
Subsystem: NEC Corporation USB 2.0 [1033:00e0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 132 (4000ns min, 8500ns max), Cache Line Size: 128 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at dd302000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
04:04.0 VGA compatible controller [0300]: ATI Technologies Inc Rage XL
[1002:4752] (rev 27) (prog-if 00 [VGA controller])
Subsystem: ATI Technologies Inc Rage XL [1002:8008]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 66 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at de000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at 3000 [size=256]
Region 2: Memory at dd303000 (32-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at 40100000 [disabled] [size=128K]
Capabilities: <access denied>
** Sound cards:
-- System Information:
Debian Release: squeeze/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.32-trunk-amd64 (SMP w/4 CPU cores)
Locale: LANG=hu_HU.UTF-8, LC_CTYPE=hu_HU.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.32-trunk-amd64 depends on:
ii debconf [debconf-2.0] 1.5.28 Debian configuration management sy
ii initramfs-tools [linux-initr 0.93.4 tools for generating an initramfs
ii module-init-tools 3.12~pre1-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.32-trunk-amd64 recommends:
ii firmware-linux-free 2.6.32-5 Binary firmware for various driver
Versions of packages linux-image-2.6.32-trunk-amd64 suggests:
pn grub | lilo <none> (no description available)
pn linux-doc-2.6.32 <none> (no description available)
Versions of packages linux-image-2.6.32-trunk-amd64 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
-- debconf information:
linux-image-2.6.32-trunk-amd64/postinst/bootloader-error-2.6.32-trunk-amd64:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.32-trunk-amd64/postinst/depmod-error-initrd-2.6.32-trunk-amd64:
false
linux-image-2.6.32-trunk-amd64/prerm/removing-running-kernel-2.6.32-trunk-amd64:
true
linux-image-2.6.32-trunk-amd64/postinst/bootloader-test-error-2.6.32-trunk-amd64:
* linux-image-2.6.32-trunk-amd64/postinst/missing-firmware-2.6.32-trunk-amd64:
linux-image-2.6.32-trunk-amd64/prerm/would-invalidate-boot-loader-2.6.32-trunk-amd64:
true
--- End Message ---
