Your message dated Wed, 01 May 2013 02:41:13 +0100
with message-id <1367372473.5106.76.ca...@deadeye.wl.decadent.org.uk>
and subject line Re: Bug#706499: Ethernet with Realtek R8169 only working with
IPV6
has caused the Debian Bug report #706499,
regarding Ethernet with Realtek R8169 only working with IPV6
to be marked as done.
This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.
(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact ow...@bugs.debian.org
immediately.)
--
706499: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=706499
Debian Bug Tracking System
Contact ow...@bugs.debian.org with problems
--- Begin Message ---
Package: firmware-realtek
Version: 0.36+wheezy.1
Severity: normal
Hello,
please refer to this bug:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=611954
and
http://serverfault.com/questions/384165/after-installing-debian-squeeze-ethernet-does-not-come-up
The card only works when you do a manually ifup eth0 with IPV4.
But not every time - sometimes it is simply dead for IPV4.
Here what you see when it comes up:
[ 12.096480] uli526x 0000:00:0d.0: eth1: NIC Link is Down
[ 12.551617] r8169 0000:02:07.0: eth0: link up
[ 12.551821] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 18.235598] Netfilter messages via NETLINK v0.30.
[ 22.568023] eth0: no IPv6 routers present
[ 24.229825] device eth0 entered promiscuous mode
[ 260.098704] device eth0 left promiscuous mode
[ 1222.481295] r8169 0000:02:07.0: eth0: link down
[ 1222.481308] r8169 0000:02:07.0: eth0: link down
[ 1222.481564] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 1225.543046] r8169 0000:02:07.0: eth0: link up
[ 1225.543248] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 1235.824012] eth0: no IPv6 routers present
lspci shows:
02:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8169 PCI
Gigabit Ethernet Controller (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RTL8169/8110 Family PCI
Gigabit Ethernet NIC
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 20
I/O ports at e000 [size=256]
Memory at fbff9c00 (32-bit, non-prefetchable) [size=256]
Expansion ROM at fbfc0000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Kernel driver in use: r8169
Regards
Karsten
-- System Information:
Debian Release: 7.0
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 3.2.0-4-486
Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
firmware-realtek depends on no packages.
firmware-realtek recommends no packages.
Versions of packages firmware-realtek suggests:
ii initramfs-tools 0.109.1
ii linux-image-3.2.0-4-486 [linux-image] 3.2.41-2
-- no debconf information
--- End Message ---
--- Begin Message ---
On Wed, 2013-05-01 at 01:19 +0200, Karsten Malcher wrote:
> Package: firmware-realtek
> Version: 0.36+wheezy.1
> Severity: normal
>
> Hello,
>
> please refer to this bug:
> http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=611954
> and
> http://serverfault.com/questions/384165/after-installing-debian-squeeze-ethernet-does-not-come-up
>
> The card only works when you do a manually ifup eth0 with IPV4.
> But not every time - sometimes it is simply dead for IPV4.
[...]
This is not a firmware bug.
Ben.
--
Ben Hutchings
Knowledge is power. France is bacon.
signature.asc
Description: This is a digitally signed message part
--- End Message ---
