Package: src:linux
Version: 3.2.35-2
Severity: important
Tags: upstream
Dear Maintainer,
I am unable to use any of my PCI slots of my new motherboard (a recent HW
upgrade). Tested with two PCI network cards (1. Atheros chip based WiFi card I
used with my previous mobo for WiFi AP, and 2. a 3Com NIC) placed repeatedly in
different PCI slots. The results were always the same:
1. during boot the kernel loads the appropriate modules (e.g. 3c59x), all
appears to look just fine in dmesg.
2. unless I bring the interfaces associated with the network cards up,
everything works as expected.
3. the moment I issue the 'ifup ethX' command, the following is printed in
/var/log/syslog:
Feb 23 22:02:39 poo avahi-daemon[2437]: Joining mDNS multicast group on
interface eth1.IPv4 with address 192.168.1.1.
Feb 23 22:02:39 poo NetworkManager[4070]: <info> (eth1): carrier now ON (device
state 10)
Feb 23 22:02:39 poo kernel: [ 669.071740] eth1: setting full-duplex.
Feb 23 22:02:39 poo avahi-daemon[2437]: New relevant interface eth1.IPv4 for
mDNS.
Feb 23 22:02:39 poo avahi-daemon[2437]: Registering new address record for
192.168.1.1 on eth1.IPv4.
Feb 23 22:02:40 poo avahi-daemon[2437]: Joining mDNS multicast group on
interface eth1.IPv6 with address fe80::210:5aff:fec0:2aab.
Feb 23 22:02:40 poo avahi-daemon[2437]: New relevant interface eth1.IPv6 for
mDNS.
Feb 23 22:02:40 poo avahi-daemon[2437]: Registering new address record for
fe80::210:5aff:fec0:2aab on eth1.*.
Feb 23 22:02:41 poo ntpd[2294]: Listen normally on 9 eth1 192.168.1.1 UDP 123
Feb 23 22:02:41 poo ntpd[2294]: Listen normally on 10 eth1
fe80::210:5aff:fec0:2aab UDP 123
Feb 23 22:02:41 poo ntpd[2294]: peers refreshed
Feb 23 22:02:48 poo kernel: [ 678.963693] eth1: transmit timed out, tx_status
00 status 8601.
Feb 23 22:02:48 poo kernel: [ 678.963713] diagnostics: net 0cd8 media 8880
dma 0000003a fifo 0000
Feb 23 22:02:48 poo kernel: [ 678.963722] eth1: Interrupt posted but not
delivered -- IRQ blocked by another device?
Feb 23 22:02:48 poo kernel: [ 678.963796] Flags; bus-master 1, dirty 16(0)
current 16(0)
Feb 23 22:02:48 poo kernel: [ 678.963803] Transmit list 00000000 vs.
ffff880037000200.
Feb 23 22:02:48 poo kernel: [ 678.963810] 0: @ffff880037000200 length
8000005a status 0001005a
Feb 23 22:02:48 poo kernel: [ 678.963812] 1: @ffff880037000298 length
80000036 status 00010036
Feb 23 22:02:48 poo kernel: [ 678.963814] 2: @ffff880037000330 length
8000004e status 0001004e
Feb 23 22:02:48 poo kernel: [ 678.963816] 3: @ffff8800370003c8 length
80000122 status 0c010122
Feb 23 22:02:48 poo kernel: [ 678.963818] 4: @ffff880037000460 length
800000c4 status 0c0100c4
Feb 23 22:02:48 poo kernel: [ 678.963820] 5: @ffff8800370004f8 length
80000122 status 0c010122
Feb 23 22:02:48 poo kernel: [ 678.963822] 6: @ffff880037000590 length
80000122 status 0c010122
Feb 23 22:02:48 poo kernel: [ 678.963824] 7: @ffff880037000628 length
8000010a status 0c01010a
Feb 23 22:02:48 poo kernel: [ 678.963826] 8: @ffff8800370006c0 length
80000046 status 00010046
Feb 23 22:02:48 poo kernel: [ 678.963828] 9: @ffff880037000758 length
8000006e status 0001006e
Feb 23 22:02:48 poo kernel: [ 678.963830] 10: @ffff8800370007f0 length
80000172 status 00010172
Feb 23 22:02:48 poo kernel: [ 678.963832] 11: @ffff880037000888 length
800000bd status 0c0100bd
Feb 23 22:02:48 poo kernel: [ 678.963834] 12: @ffff880037000920 length
800000d8 status 000100d8
Feb 23 22:02:48 poo kernel: [ 678.963836] 13: @ffff8800370009b8 length
8000011a status 0c01011a
Feb 23 22:02:48 poo kernel: [ 678.963837] 14: @ffff880037000a50 length
80000172 status 80010172
Feb 23 22:02:48 poo kernel: [ 678.963839] 15: @ffff880037000ae8 length
800000bd status 8c0100bd
Feb 23 22:02:51 poo dnsmasq-dhcp[3574]: DHCPDISCOVER(eth1) 10.0.0.1
00:1c:23:a2:e7:c3
Feb 23 22:02:51 poo dnsmasq-dhcp[3574]: DHCPOFFER(eth1) 192.168.1.141
00:1c:23:a2:e7:c3
Feb 23 22:02:53 poo kernel: [ 683.964682] eth1: transmit timed out, tx_status
00 status 8201.
Feb 23 22:02:53 poo kernel: [ 683.964700] diagnostics: net 0cd8 media 8880
dma 00000032 fifo 0000
Feb 23 22:02:53 poo kernel: [ 683.964709] eth1: Interrupt posted but not
delivered -- IRQ blocked by another device?
Feb 23 22:02:53 poo kernel: [ 683.964777] Flags; bus-master 1, dirty 32(0)
current 32(0)
Feb 23 22:02:53 poo kernel: [ 683.964783] Transmit list 00000000 vs.
ffff880037000200.
Feb 23 22:02:53 poo kernel: [ 683.964790] 0: @ffff880037000200 length
80000058 status 0c010058
Feb 23 22:02:53 poo kernel: [ 683.964792] 1: @ffff880037000298 length
80000172 status 00010172
Feb 23 22:02:53 poo kernel: [ 683.964794] 2: @ffff880037000330 length
800000bd status 0c0100bd
Feb 23 22:02:53 poo kernel: [ 683.964796] 3: @ffff8800370003c8 length
8000015a status 0001015a
Feb 23 22:02:53 poo kernel: [ 683.964797] 4: @ffff880037000460 length
800000b1 status 0c0100b1
Feb 23 22:02:53 poo kernel: [ 683.964799] 5: @ffff8800370004f8 length
8000010a status 0c01010a
Feb 23 22:02:53 poo kernel: [ 683.964801] 6: @ffff880037000590 length
8000013a status 0001013a
Feb 23 22:02:53 poo kernel: [ 683.964803] 7: @ffff880037000628 length
8000015a status 0001015a
Feb 23 22:02:53 poo kernel: [ 683.964805] 8: @ffff8800370006c0 length
800000b1 status 0c0100b1
Feb 23 22:02:53 poo kernel: [ 683.964807] 9: @ffff880037000758 length
80000036 status 00010036
Feb 23 22:02:53 poo kernel: [ 683.964809] 10: @ffff8800370007f0 length
8000005a status 0001005a
Feb 23 22:02:53 poo kernel: [ 683.964811] 11: @ffff880037000888 length
8000011a status 0c01011a
Feb 23 22:02:53 poo kernel: [ 683.964813] 12: @ffff880037000920 length
80000126 status 0c010126
Feb 23 22:02:53 poo kernel: [ 683.964815] 13: @ffff8800370009b8 length
8000013a status 0001013a
Feb 23 22:02:53 poo kernel: [ 683.964817] 14: @ffff880037000a50 length
80000046 status 80010046
Feb 23 22:02:53 poo kernel: [ 683.964819] 15: @ffff880037000ae8 length
8000015a status 8001015a
...and this into /var/log/messages:
Feb 23 21:58:01 poo kernel: [ 391.545008] eth1: setting full-duplex.
Feb 23 21:58:01 poo kernel: [ 391.545033] IPv6: ADDRCONF(NETDEV_CHANGE): eth1:
link becomes ready
Feb 23 21:58:10 poo kernel: [ 401.322302] ------------[ cut here ]------------
Feb 23 21:58:10 poo kernel: [ 401.322314] WARNING: at
net/sched/sch_generic.c:254 dev_watchdog+0xe3/0x153()
Feb 23 21:58:10 poo kernel: [ 401.322316] Hardware name:
Feb 23 21:58:10 poo kernel: [ 401.322318] NETDEV WATCHDOG: eth1 (3c59x):
transmit queue 0 timed out
Feb 23 21:58:10 poo kernel: [ 401.322320] Modules linked in: xt_state
iptable_filter ipt_MASQUERADE iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4
nf_nat_ipv4 nf_nat nf_conntrack ip_tables x_tables binfmt_misc nfsd auth_rpcgss
nfs_acl nfs lockd fscache sunrpc loop snd_hda_codec_realtek hid_generic usbhid
hid snd_hda_intel snd_hda_codec coretemp kvm_intel snd_hwdep kvm i915 snd_pcm
snd_page_alloc crc32c_intel drm_kms_helper drm snd_seq ghash_clmulni_intel
snd_seq_device cryptd snd_timer iTCO_wdt psmouse snd iTCO_vendor_support
i2c_i801 microcode acpi_cpufreq mperf processor lpc_ich pcspkr serio_raw
mfd_core evdev soundcore i2c_algo_bit i2c_core mei ehci_pci button video
ehci_hcd ext4 crc16 jbd2 mbcache sg sr_mod cdrom sd_mod crc_t10dif ata_generic
3c59x mii fan thermal thermal_sys xhci_hcd usbcore usb_common ata_piix libata
scsi_mod e1000e
Feb 23 21:58:10 poo kernel: [ 401.322385] Pid: 0, comm: swapper/2 Not tainted
3.8.0 #1
Feb 23 21:58:10 poo kernel: [ 401.322387] Call Trace:
Feb 23 21:58:10 poo kernel: [ 401.322389] <IRQ> [<ffffffff8103ccf0>] ?
warn_slowpath_common+0x76/0x8a
Feb 23 21:58:10 poo kernel: [ 401.322399] [<ffffffff812e10d9>] ?
netif_tx_lock+0x7a/0x7a
Feb 23 21:58:10 poo kernel: [ 401.322402] [<ffffffff8103cd9c>] ?
warn_slowpath_fmt+0x45/0x4a
Feb 23 21:58:10 poo kernel: [ 401.322406] [<ffffffff812e10c6>] ?
netif_tx_lock+0x67/0x7a
Feb 23 21:58:10 poo kernel: [ 401.322412] [<ffffffff812e11bc>] ?
dev_watchdog+0xe3/0x153
Feb 23 21:58:10 poo kernel: [ 401.322416] [<ffffffff81047efc>] ?
call_timer_fn+0x34/0xf6
Feb 23 21:58:10 poo kernel: [ 401.322420] [<ffffffff812e10d9>] ?
netif_tx_lock+0x7a/0x7a
Feb 23 21:58:10 poo kernel: [ 401.322424] [<ffffffff81049426>] ?
run_timer_softirq+0x18d/0x1d6
Feb 23 21:58:10 poo kernel: [ 401.322429] [<ffffffff811c3099>] ?
timerqueue_add+0x79/0x98
Feb 23 21:58:10 poo kernel: [ 401.322432] [<ffffffff81043396>] ?
__do_softirq+0xac/0x1d1
Feb 23 21:58:10 poo kernel: [ 401.322436] [<ffffffff81074d18>] ?
ktime_get+0x62/0x6a
Feb 23 21:58:10 poo kernel: [ 401.322442] [<ffffffff810285f9>] ?
paravirt_write_msr+0xb/0xe
Feb 23 21:58:10 poo kernel: [ 401.322446] [<ffffffff81079537>] ?
clockevents_program_event+0x9a/0xb6
Feb 23 21:58:10 poo kernel: [ 401.322451] [<ffffffff8138cbdc>] ?
call_softirq+0x1c/0x30
Feb 23 21:58:10 poo kernel: [ 401.322454] [<ffffffff8100f9ce>] ?
do_softirq+0x3a/0x78
Feb 23 21:58:10 poo kernel: [ 401.322457] [<ffffffff81043581>] ?
irq_exit+0x3a/0x91
Feb 23 21:58:10 poo kernel: [ 401.322462] [<ffffffff81028a74>] ?
smp_apic_timer_interrupt+0x73/0x81
Feb 23 21:58:10 poo kernel: [ 401.322465] [<ffffffff8138c49d>] ?
apic_timer_interrupt+0x6d/0x80
Feb 23 21:58:10 poo kernel: [ 401.322466] <EOI> [<ffffffff81079537>] ?
clockevents_program_event+0x9a/0xb6
Feb 23 21:58:10 poo kernel: [ 401.322474] [<ffffffff812a537f>] ?
arch_local_irq_enable+0x7/0x8
Feb 23 21:58:10 poo kernel: [ 401.322477] [<ffffffff812a5aad>] ?
cpuidle_wrap_enter+0x3c/0x71
Feb 23 21:58:10 poo kernel: [ 401.322480] [<ffffffff812a5732>] ?
cpuidle_enter_state+0xa/0x31
Feb 23 21:58:10 poo kernel: [ 401.322483] [<ffffffff812a5848>] ?
cpuidle_idle_call+0xef/0x1a6
Feb 23 21:58:10 poo kernel: [ 401.322488] [<ffffffff81014dfd>] ?
cpu_idle+0x9c/0xe6
Feb 23 21:58:10 poo kernel: [ 401.322492] [<ffffffff81378b1b>] ?
start_secondary+0x1e0/0x1e6
Feb 23 21:58:10 poo kernel: [ 401.322495] ---[ end trace 07876c6d48c7014f ]---
Feb 23 22:02:39 poo kernel: [ 669.071740] eth1: setting full-duplex.
At this point as far as debian is concerned the device works. In reality it
does not work at all. No packets are being transmitted or received. After a few
minutes of running with the device brought up the output of /proc/interrupts
shows:
CPU0 CPU1 CPU2 CPU3
18: 0 0 0 0
IO-APIC-fasteoi eth1 (the PCI card)
40: 7154 721 4809 742 PCI-MSI-edge
eth0 (the integrated eth controller of the mobo)
The attached 'lspci' logs also show the 3Com card had IRQ18 assigned to it.
NOTE: so did the motherboard's SMBus Controller (00:1f:3).
Note 1: A side-effect of bringing the iface up is that my USB keyboard slows
down considerably (as if the rate at which it reads keypresses would go down to
~10 presses per second).
Note 2: I am currently running kernel 3.8, because the stock debian 3.2 kernel
freezes the computer after what appears to be a random time (unrelated to what
I actually do on the system, if doing anything at all). However the bug I am
reporting here applies exactly in the same manner to both 3.2 and 3.8 kernels.
Note 3: I tried booting both kernels with the 'pci=nomsi' parameter, but that
didn't change anything.
Note 4: This is likely not a HW issue, since I tested the configuration in
windoze, and all was working as expected.
Thank you for your help,
-szabolcs
-- Package-specific info:
** Kernel log: boot messages should be attached
** Model information
sys_vendor:
product_name:
product_version:
chassis_vendor:
chassis_version:
bios_vendor: Intel Corporation
bios_version: SLZ7710H.86A.0095.2013.0117.1516
board_vendor: Intel Corporation
board_name: DZ77SL-50K
board_version: AAG55115-300
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Xeon E3-1200 v2/3rd Gen Core
processor DRAM Controller [8086:0150] (rev 09)
Subsystem: Intel Corporation Device [8086:2030]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:02.0 VGA compatible controller [0300]: Intel Corporation Xeon E3-1200 v2/3rd
Gen Core processor Graphics Controller [8086:0152] (rev 09) (prog-if 00 [VGA
controller])
Subsystem: Intel Corporation Device [8086:2030]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 43
Region 0: Memory at f7800000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at f000 [size=64]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:14.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset
Family USB xHCI Host Controller [8086:1e31] (rev 04) (prog-if 30 [XHCI])
Subsystem: Intel Corporation Device [8086:2030]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 41
Region 0: Memory at f7d20000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
00:16.0 Communication controller [0780]: Intel Corporation 7 Series/C210 Series
Chipset Family MEI Controller #1 [8086:1e3a] (rev 04)
Subsystem: Intel Corporation Device [8086:2030]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 42
Region 0: Memory at f7d3a000 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
Kernel driver in use: mei
00:19.0 Ethernet controller [0200]: Intel Corporation 82579V Gigabit Network
Connection [8086:1503] (rev 04)
Subsystem: Intel Corporation Device [8086:2030]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 40
Region 0: Memory at f7d00000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at f7d38000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at f060 [size=32]
Capabilities: <access denied>
Kernel driver in use: e1000e
00:1a.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset
Family USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Device [8086:2030]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f7d37000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:1b.0 Audio device [0403]: Intel Corporation 7 Series/C210 Series Chipset
Family High Definition Audio Controller [8086:1e20] (rev 04)
Subsystem: Intel Corporation Device [8086:2030]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 44
Region 0: Memory at f7d30000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset
Family PCI Express Root Port 1 [8086:1e10] (rev c4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.7 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset
Family PCI Express Root Port 8 [8086:1e1e] (rev c4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=03, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: f7c00000-f7cfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset
Family USB Enhanced Host Controller #1 [8086:1e26] (rev 04) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Device [8086:2030]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f7d36000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:1f.0 ISA bridge [0601]: Intel Corporation Z77 Express Chipset LPC Controller
[8086:1e44] (rev 04)
Subsystem: Intel Corporation Device [8086:2030]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
00:1f.2 IDE interface [0101]: Intel Corporation 7 Series/C210 Series Chipset
Family 4-port SATA Controller [IDE mode] [8086:1e00] (rev 04) (prog-if 8f
[Master SecP SecO PriP PriO])
Subsystem: Intel Corporation Device [8086:2030]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at f130 [size=8]
Region 1: I/O ports at f120 [size=4]
Region 2: I/O ports at f110 [size=8]
Region 3: I/O ports at f100 [size=4]
Region 4: I/O ports at f0f0 [size=16]
Region 5: I/O ports at f0e0 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
00:1f.3 SMBus [0c05]: Intel Corporation 7 Series/C210 Series Chipset Family
SMBus Controller [8086:1e22] (rev 04)
Subsystem: Intel Corporation Device [8086:2030]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f7d35000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at f040 [size=32]
00:1f.5 IDE interface [0101]: Intel Corporation 7 Series/C210 Series Chipset
Family 2-port SATA Controller [IDE mode] [8086:1e08] (rev 04) (prog-if 85
[Master SecO PriO])
Subsystem: Intel Corporation Device [8086:2030]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at f0d0 [size=8]
Region 1: I/O ports at f0c0 [size=4]
Region 2: I/O ports at f0b0 [size=8]
Region 3: I/O ports at f0a0 [size=4]
Region 4: I/O ports at f090 [size=16]
Region 5: I/O ports at f080 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
02:00.0 PCI bridge [0604]: Integrated Technology Express, Inc. Device
[1283:8892] (rev 30) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=02, secondary=03, subordinate=03, sec-latency=64
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: f7c00000-f7cfffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
03:02.0 Ethernet controller [0200]: 3Com Corporation 3c905B 100BaseTX [Cyclone]
[10b7:9055] (rev 30)
Subsystem: 3Com Corporation 3C905B Fast Etherlink XL 10/100 [10b7:9055]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2500ns min, 2500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at e000 [size=128]
Region 1: Memory at f7c20000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at f7c00000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: 3c59x
** USB devices:
Bus 003 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 004 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 003: ID 04b3:3103 IBM Corp. ScrollPoint Pro Mouse
Bus 003 Device 004: ID 04f2:0116 Chicony Electronics Co., Ltd KU-2971/KU-0325
Keyboard
-- System Information:
Debian Release: 7.0
APT prefers testing
APT policy: (500, 'testing')
Architecture: amd64 (x86_64)
Foreign Architectures: i386
Kernel: Linux 3.8.0 (SMP w/4 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.2.0-4-amd64 depends on:
ii debconf [debconf-2.0] 1.5.49
ii initramfs-tools [linux-initramfs-tool] 0.109
ii kmod 9-2
ii linux-base 3.5
ii module-init-tools 9-2
Versions of packages linux-image-3.2.0-4-amd64 recommends:
ii firmware-linux-free 3.2
Versions of packages linux-image-3.2.0-4-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 1.99-26
pn linux-doc-3.2 <none>
Versions of packages linux-image-3.2.0-4-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information excluded
--
To UNSUBSCRIBE, email to debian-kernel-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
Archive: http://lists.debian.org/20130225114522.3136.93265.reportbug@poo
