Package: src:linux
Version: 3.2.23-1
Severity: normal
Dear Maintainer,
*** Please consider answering these questions, where appropriate ***
* What led up to the situation? Installation of PDC20376 sata controller and
2tb WD green disks
* What exactly did you do (or not do) that was effective (or
ineffective)? WD 2TB "GREEN" disks not detected ("assuming NODEV" on the
probe). Smaller (160-250G), non-green WD & seagate drives are ok.
Disks function ok when attached to sata_svw device (mac internal
controller).
* What was the outcome? Disks do not appear as devices (in /dev) so can't
be seen by fdisk, gparted etc when attached to pdc controller.
* What outcome did you expect instead? Devices should have been detected and
/dev populated.
*** End of the template - remove these lines ***
-- Package-specific info:
** Kernel log: boot messages should be attached
** Model information
revision : 3.1 (pvr 003c 0301)
revision : 3.1 (pvr 003c 0301)
platform : PowerMac
model : PowerMac7,3
machine : PowerMac7,3
motherboard : PowerMac7,3 MacRISC4 Power Macintosh
** Network interface configuration:
auto lo
iface lo inet loopback
allow-hotplug eth0
iface eth0 inet static
address 1.1.1.19
netmask 255.255.255.0
network 1.1.1.0
broadcast 1.1.1.255
gateway 1.1.1.1
auto eth0:0
iface eth0:0 inet static
address 1.1.1.11
netmask 255.255.255.0
network 1.1.1.0
broadcast 1.1.1.255
auto eth1
allow-hotplug eth1
iface eth1 inet static
address 1.1.2.1
netmask 255.255.255.0
network 1.1.2.0
broadcast 1.1.2.255
auto eth2
allow-hotplug eth2
iface eth2 inet static
address 1.1.3.1
netmask 255.255.255.0
network 1.1.3.0
broadcast 1.1.3.255
** PCI devices:
0000:f0:0b.0 Host bridge [0600]: Apple Inc. U3H AGP Bridge [106b:0059]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 16, Cache Line Size: 32 bytes
Capabilities: [80] AGP version 3.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans+
64bit+ FW+ AGP3- Rate=x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit+ FW-
Rate=<none>
Kernel driver in use: agpgart-uninorth
0000:f0:10.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee
ATI Radeon R300 ND [Radeon 9700 Pro] [1002:4e44] (prog-if 00 [VGA controller])
Subsystem: Advanced Micro Devices [AMD] nee ATI Radeon R300 ND [Radeon
9700 Pro] [1002:4e44]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (2000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 48
Region 0: Memory at c0000000 (32-bit, prefetchable) [size=256M]
Region 1: I/O ports at 0400 [size=256]
Region 2: Memory at b0000000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at b0020000 [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Status: RQ=80 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW-
Rate=<none>
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: radeonfb
0001:00:00.0 Host bridge [0600]: Apple Inc. U3 HT Bridge [106b:0057]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [40] HyperTransport: Host or Secondary Interface
Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide- Slave-
<EOCErr- DUL-
Link Control: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO-
<CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit
DwFcInEn- LWO=16bit DwFcOutEn-
Revision ID: 1.04
Link Frequency: 600MHz
Link Error: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability: 200MHz+ 300MHz+ 400MHz+ 500MHz+
600MHz+ 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC- LDTSTOP+ CRCTM+ ECTLT- 64bA- UIDRD-
ExtRS+ UCnfE-
Error Handling: PFlE- OFlE- PFE- OFE- EOCFE- RFE- CRCFE-
SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
0001:00:01.0 PCI bridge [0604]: Advanced Micro Devices [AMD] AMD-8131 PCI-X
Bridge [1022:7450] (rev 12) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Bus: primary=00, secondary=06, subordinate=06, sec-latency=32
I/O behind bridge: 00001000-00001fff
Memory behind bridge: 90000000-900fffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat+ DiscTmrSERREn-
Capabilities: [a0] PCI-X bridge device
Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=conv
Status: Dev=00:01.0 64bit+ 133MHz+ SCD- USC- SCO- SRD-
Upstream: Capacity=14 CommitmentLimit=65535
Downstream: Capacity=2 CommitmentLimit=65535
Capabilities: [b8] HyperTransport: Interrupt Discovery and Configuration
Capabilities: [c0] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=1 UnitCnt=2 MastHost- DefDir- DUL-
Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO-
<CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit
DwFcInEn- LWO=16bit DwFcOutEn-
Link Control 1: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO-
<CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit
DwFcInEn- LWO=8bit DwFcOutEn-
Revision ID: 1.02
Link Frequency 0: 600MHz
Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz- 400MHz+ 500MHz-
600MHz+ 800MHz+ 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC- LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
Link Frequency 1: 400MHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz+ 300MHz- 400MHz+ 500MHz-
600MHz+ 800MHz+ 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Error Handling: PFlE- OFlE- PFE- OFE- EOCFE- RFE- CRCFE-
SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
0001:00:02.0 PCI bridge [0604]: Advanced Micro Devices [AMD] AMD-8131 PCI-X
Bridge [1022:7450] (rev 12) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Bus: primary=00, secondary=07, subordinate=07, sec-latency=32
Memory behind bridge: a0000000-a00fffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [a0] PCI-X bridge device
Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=66MHz
Status: Dev=00:02.0 64bit+ 133MHz+ SCD- USC- SCO- SRD-
Upstream: Capacity=14 CommitmentLimit=65535
Downstream: Capacity=2 CommitmentLimit=65535
Capabilities: [b8] HyperTransport: Interrupt Discovery and Configuration
0001:00:03.0 PCI bridge [0604]: Apple Inc. K2 HT-PCI Bridge [106b:0045]
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
Memory behind bridge: 80000000-800fffff
Prefetchable memory behind bridge: 00000000-000fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [70] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=3 UnitCnt=5 MastHost- DefDir- DUL-
Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO-
<CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 0: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit
DwFcInEn- LWO=8bit DwFcOutEn-
Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+
<CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit
DwFcInEn- LWO=8bit DwFcOutEn-
Revision ID: 1.04
Link Frequency 0: 400MHz
Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz- 400MHz+ 500MHz-
600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC- LDTSTOP+ CRCTM+ ECTLT- 64bA- UIDRD-
Link Frequency 1: 200MHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz-
600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Error Handling: PFlE- OFlE- PFE- OFE- EOCFE- RFE- CRCFE-
SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
Capabilities: [90] HyperTransport: Interrupt Discovery and Configuration
0001:00:04.0 PCI bridge [0604]: Apple Inc. K2 HT-PCI Bridge [106b:0046]
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
Memory behind bridge: 80100000-801fffff
Prefetchable memory behind bridge: 00000000-000fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [70] HyperTransport: Revision ID: 1.04
0001:00:05.0 PCI bridge [0604]: Apple Inc. K2 HT-PCI Bridge [106b:0047]
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
Memory behind bridge: 80200000-802fffff
Prefetchable memory behind bridge: 00000000-000fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [70] HyperTransport: Revision ID: 1.04
0001:00:06.0 PCI bridge [0604]: Apple Inc. K2 HT-PCI Bridge [106b:0048]
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
Memory behind bridge: 80300000-805fffff
Prefetchable memory behind bridge: 00000000-000fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [70] HyperTransport: Revision ID: 1.04
0001:00:07.0 PCI bridge [0604]: Apple Inc. K2 HT-PCI Bridge [106b:0049]
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
Memory behind bridge: 80600000-806fffff
Prefetchable memory behind bridge: 00000000-000fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [70] HyperTransport: Revision ID: 1.04
0001:01:07.0 Unassigned class [ff00]: Apple Inc. K2 KeyLargo Mac/IO [106b:0041]
(rev 60)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16, Cache Line Size: 64 bytes
Region 0: Memory at 80000000 (32-bit, non-prefetchable) [size=512K]
Kernel driver in use: macio
0001:01:08.0 USB controller [0c03]: Apple Inc. K2 KeyLargo USB [106b:0040]
(prog-if 10 [OHCI])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (750ns min, 21500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 27
Region 0: Memory at 80081000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
0001:01:09.0 USB controller [0c03]: Apple Inc. K2 KeyLargo USB [106b:0040]
(prog-if 10 [OHCI])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (750ns min, 21500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 28
Region 0: Memory at 80080000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
0001:02:0b.0 USB controller [0c03]: NEC Corporation USB [1033:0035] (rev 43)
(prog-if 10 [OHCI])
Subsystem: NEC Corporation Hama USB 2.0 CardBus [1033:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (250ns min, 10500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 63
Region 0: Memory at 80102000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+
Kernel driver in use: ohci_hcd
0001:02:0b.1 USB controller [0c03]: NEC Corporation USB [1033:0035] (rev 43)
(prog-if 10 [OHCI])
Subsystem: NEC Corporation Hama USB 2.0 CardBus [1033:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (250ns min, 10500ns max), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 63
Region 0: Memory at 80101000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+
Kernel driver in use: ohci_hcd
0001:02:0b.2 USB controller [0c03]: NEC Corporation USB 2.0 [1033:00e0] (rev
04) (prog-if 20 [EHCI])
Subsystem: NEC Corporation USB 2.0 [1033:00e0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (4000ns min, 8500ns max), Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 63
Region 0: Memory at 80100000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ehci_hcd
0001:03:0d.0 Unassigned class [ff00]: Apple Inc. K2 ATA/100 [106b:0043]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin ? routed to IRQ 39
Region 0: Memory at 80204000 (32-bit, non-prefetchable) [size=16K]
Kernel driver in use: pata-pci-macio
0001:03:0e.0 FireWire (IEEE 1394) [0c00]: Apple Inc. K2 FireWire [106b:0042]
(prog-if 10 [OHCI])
Subsystem: Apple Inc. Device [106b:5811]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 248 (3000ns min, 6000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 40
Region 0: Memory at 80200000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+
Kernel driver in use: firewire_ohci
0001:04:0f.0 Ethernet controller [0200]: Apple Inc. K2 GMAC (Sun GEM)
[106b:004c]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR+ INTx-
Latency: 16 (16000ns min, 16000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 41
Region 0: Memory at 80400000 (32-bit, non-prefetchable) [size=2M]
Expansion ROM at 80300000 [disabled] [size=1M]
Kernel driver in use: gem
0001:05:0c.0 IDE interface [0101]: Broadcom K2 SATA [1166:0240] (prog-if 8f
[Master SecP SecO PriP PriO])
Subsystem: Broadcom K2 SATA [1166:0240]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16
Interrupt: pin ? routed to IRQ 17
Region 0: I/O ports at <unassigned> [disabled]
Region 1: I/O ports at <unassigned> [disabled]
Region 2: I/O ports at <unassigned> [disabled]
Region 3: I/O ports at <unassigned> [disabled]
Region 4: I/O ports at <unassigned> [disabled]
Region 5: Memory at 80600000 (32-bit, non-prefetchable) [size=8K]
Kernel driver in use: sata_svw
0001:06:02.0 RAID bus controller [0104]: Promise Technology, Inc. PDC20376
(FastTrak 376) [105a:3376] (rev 02)
Subsystem: Promise Technology, Inc. PDC20376 (FastTrak 376) [105a:3376]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (1000ns min, 4500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 52
Region 0: I/O ports at 1080 [size=64]
Region 1: I/O ports at 10c0 [size=16]
Region 2: I/O ports at 1000 [size=128]
Region 3: Memory at 90000000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at 90040000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at 90020000 [disabled] [size=64K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: sata_promise
0001:06:03.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5700
Gigabit Ethernet [14e4:1644] (rev 12)
Subsystem: 3Com Corporation 3C996-T 1000Base-T [10b7:1000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (16000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 53
Region 0: Memory at 90010000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [40] PCI-X non-bridge device
Command: DPERE- ERO+ RBC=512 OST=1
Status: Dev=ff:1f.1 64bit+ 133MHz+ SCD- USC- DC=simple
DMMRBC=512 DMOST=1 DMCRS=8 RSCEM- 266MHz- 533MHz-
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Product Name: Broadcom Gigabit Ethernet Controller
Read-only fields:
[PN] Part number: BCM95700A6
[EC] Engineering changes: 105809-16
[SN] Serial number: 0123456789
[MN] Manufacture ID: 31 34 65 34
[RV] Reserved: checksum bad, 36 byte(s) reserved
Read/write fields:
[YA] Asset tag: XYZ01234567
[RW] Read-write area: 107 byte(s) free
End
Capabilities: [58] MSI: Enable- Count=1/8 Maskable- 64bit+
Address: 00393400d0589ed8 Data: 0006
Kernel driver in use: tg3
0001:07:04.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5700
Gigabit Ethernet [14e4:1644] (rev 12)
Subsystem: 3Com Corporation 3C996-T 1000Base-T [10b7:1000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (16000ns min)
Interrupt: pin A routed to IRQ 54
Region 0: Memory at a0000000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [40] PCI-X non-bridge device
Command: DPERE- ERO- RBC=512 OST=1
Status: Dev=07:04.1 64bit+ 133MHz+ SCD- USC- DC=simple
DMMRBC=512 DMOST=1 DMCRS=8 RSCEM- 266MHz- 533MHz-
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable+ DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Product Name: Broadcom Gigabit Ethernet Controller
Read-only fields:
[PN] Part number: BCM95700A6
[EC] Engineering changes: 105809-16
[SN] Serial number: 0123456789
[MN] Manufacture ID: 31 34 65 34
[RV] Reserved: checksum bad, 36 byte(s) reserved
Read/write fields:
[YA] Asset tag: XYZ01234567
[RW] Read-write area: 107 byte(s) free
End
Capabilities: [58] MSI: Enable- Count=1/8 Maskable- 64bit+
Address: 164814c060418408 Data: 0000
Kernel driver in use: tg3
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
-- System Information:
Debian Release: wheezy/sid
APT prefers testing-updates
APT policy: (500, 'testing-updates'), (500, 'testing')
Architecture: powerpc (ppc64)
Kernel: Linux 3.2.0-4-powerpc64 (SMP w/2 CPU cores)
Locale: LANG=en_AU.UTF-8, LC_CTYPE=en_AU.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.2.0-3-powerpc64 depends on:
ii debconf [debconf-2.0] 1.5.46
ii initramfs-tools [linux-initramfs-tool] 0.109
ii kmod 9-2
ii linux-base 3.5
ii module-init-tools 9-2
Versions of packages linux-image-3.2.0-3-powerpc64 recommends:
ii firmware-linux-free 3.1
Versions of packages linux-image-3.2.0-3-powerpc64 suggests:
pn debian-kernel-handbook <none>
pn linux-doc-3.2 <none>
pn mkvmlinuz <none>
Versions of packages linux-image-3.2.0-3-powerpc64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.2.0-3-powerpc64/postinst/depmod-error-initrd-3.2.0-3-powerpc64:
false
linux-image-3.2.0-3-powerpc64/prerm/removing-running-kernel-3.2.0-3-powerpc64:
true
* linux-image-3.2.0-3-powerpc64/postinst/missing-firmware-3.2.0-3-powerpc64:
linux-image-3.2.0-3-powerpc64/postinst/ignoring-ramdisk:
--
To UNSUBSCRIBE, email to debian-kernel-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
Archive:
http://lists.debian.org/20121116005644.12689.57658.report...@macmyth.outlook.theanthonys.net
