Package: linux-2.6
Version: 3.2.16-1
Severity: critical
Justification: breaks the whole system
Dear Maintainer,
*** Please consider answering these questions, where appropriate ***
* What led up to the situation?
* What exactly did you do (or not do) that was effective (or
ineffective)?
* What was the outcome of this action?
* What outcome did you expect instead?
*** End of the template - remove these lines ***
-- Package-specific info:
** Kernel log: boot messages should be attached
** Model information
not available
** Network interface configuration:
auto lo
iface lo inet loopback
auto eth0
iface eth0 inet static
address 192.168.2.40
netmask 255.255.255.0
network 192.168.2.0
broadcast 192.168.2.255
auto eth1
iface eth1 inet static
address 192.168.15.1
netmask 255.255.255.0
network 192.168.15.0
broadcast 192.168.15.255
dns-nameservers 192.168.15.1
dns-search n-agansk
auto eth2
iface eth2 inet static
address 192.168.3.1
netmask 255.255.255.0
network 192.168.3.0
broadcast 192.168.3.255
auto eth3
iface eth3 inet static
address 192.168.21.1
netmask 255.255.255.0
network 192.168.21.0
broadcast 192.168.21.255
auto dsl-provider
iface dsl-provider inet ppp
pre-up /sbin/ifconfig eth4 up # line maintained by pppoeconf
provider dsl-provider
iface tap0 inet static
address 87.226.156.62
netmask 255.255.255.0
broadcast 87.226.156.255
gateway 87.226.156.1
pre-up eciadsl-pppoeci -vpi 8 -vci 81 -mode VCM_RFC_1483_BRIDGED_ETH
-vendor 0x2001 -product 0x5100 -mc GS7470 -alt 4
down start-stop-daemon --stop --exec /usr/sbin/eciadsl-pppoeci --oknodo
--quiet
** PCI devices:
00:00.0 Host bridge [0600]: NVIDIA Corporation nForce2 IGP2 [10de:01e0] (rev c1)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Capabilities: [40] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=x1
Capabilities: [60] HyperTransport: Host or Secondary Interface
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=8bit MLWO=8bit LWI=8bit LWO=8bit
Revision ID: 0.16
Kernel driver in use: agpgart-nvidia
00:00.1 RAM memory [0500]: NVIDIA Corporation nForce2 Memory Controller 1
[10de:01eb] (rev c1)
Subsystem: EPoX Computer Co., Ltd. Device [1695:1000]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:00.2 RAM memory [0500]: NVIDIA Corporation nForce2 Memory Controller 4
[10de:01ee] (rev c1)
Subsystem: EPoX Computer Co., Ltd. Device [1695:1000]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:00.3 RAM memory [0500]: NVIDIA Corporation nForce2 Memory Controller 3
[10de:01ed] (rev c1)
Subsystem: EPoX Computer Co., Ltd. Device [1695:1000]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:00.4 RAM memory [0500]: NVIDIA Corporation nForce2 Memory Controller 2
[10de:01ec] (rev c1)
Subsystem: EPoX Computer Co., Ltd. Device [1695:1000]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:00.5 RAM memory [0500]: NVIDIA Corporation nForce2 Memory Controller 5
[10de:01ef] (rev c1)
Subsystem: EPoX Computer Co., Ltd. Device [1695:1000]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:01.0 ISA bridge [0601]: NVIDIA Corporation nForce2 ISA Bridge [10de:0060]
(rev a3)
Subsystem: EPoX Computer Co., Ltd. Device [1695:1000]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [48] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=1 UnitCnt=15 MastHost- DefDir-
Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC+ TXO-
<CRCErr=0
Link Config 0: MLWI=8bit MLWO=8bit LWI=8bit LWO=8bit
Link Control 1: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO+
<CRCErr=0
Link Config 1: MLWI=8bit MLWO=8bit LWI=8bit LWO=8bit
Revision ID: 0.00
00:01.1 SMBus [0c05]: NVIDIA Corporation nForce2 SMBus (MCP) [10de:0064] (rev
a2)
Subsystem: EPoX Computer Co., Ltd. Device [1695:1000]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 255
Region 0: I/O ports at c400 [size=32]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: nForce2_smbus
00:02.0 USB controller [0c03]: NVIDIA Corporation nForce2 USB Controller
[10de:0067] (rev a3) (prog-if 10 [OHCI])
Subsystem: EPoX Computer Co., Ltd. Device [1695:1000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at db004000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ohci_hcd
00:02.1 USB controller [0c03]: NVIDIA Corporation nForce2 USB Controller
[10de:0067] (rev a3) (prog-if 10 [OHCI])
Subsystem: EPoX Computer Co., Ltd. Device [1695:1000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 21
Region 0: Memory at db005000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ohci_hcd
00:02.2 USB controller [0c03]: NVIDIA Corporation nForce2 USB Controller
[10de:0068] (rev a3) (prog-if 20 [EHCI])
Subsystem: EPoX Computer Co., Ltd. Device [1695:1000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin C routed to IRQ 20
Region 0: Memory at db000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Debug port: BAR=1 offset=0080
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ehci_hcd
00:06.0 Multimedia audio controller [0401]: NVIDIA Corporation nForce2 AC97
Audio Controler (MCP) [10de:006a] (rev a1)
Subsystem: EPoX Computer Co., Ltd. Device [1695:1000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at b400 [size=256]
Region 1: I/O ports at b800 [size=128]
Region 2: Memory at db002000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: snd_intel8x0
00:08.0 PCI bridge [0604]: NVIDIA Corporation nForce2 External PCI Bridge
[10de:006c] (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 00009000-0000afff
Memory behind bridge: d8000000-d9ffffff
Prefetchable memory behind bridge: da000000-daffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR+
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:09.0 IDE interface [0101]: NVIDIA Corporation nForce2 IDE [10de:0065] (rev
a2) (prog-if 8a [Master SecP PriP])
Subsystem: EPoX Computer Co., Ltd. Device [1695:1000]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[size=1]
Region 4: I/O ports at f000 [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pata_amd
00:1e.0 PCI bridge [0604]: NVIDIA Corporation nForce2 AGP [10de:01e8] (rev c1)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
01:06.0 Ethernet controller [0200]: 3Com Corporation 3c905C-TX/TX-M [Tornado]
[10b7:9200] (rev 74)
Subsystem: 3Com Corporation 3C905CX-TX/TX-M Fast Etherlink for PC
Management NIC [10b7:1000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 9000 [size=128]
Region 1: Memory at d9108000 (32-bit, non-prefetchable) [size=128]
[virtual] Expansion ROM at da020000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: 3c59x
01:07.0 Ethernet controller [0200]: D-Link System Inc DGE-530T Gigabit Ethernet
Adapter (rev 11) [1186:4b01] (rev 11)
Subsystem: D-Link System Inc DGE-530T Gigabit Ethernet Adapter (rev 11)
[1186:4b01]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (5750ns min, 7750ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at d9100000 (32-bit, non-prefetchable) [size=16K]
Region 1: I/O ports at 9400 [size=256]
[virtual] Expansion ROM at da040000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Product Name: DGE-530T Gigabit Ethernet Adapter
Read-only fields:
[PN] Part number: DGE-530T
[EC] Engineering changes: Rev. 1.1
[MN] Manufacture ID: 44 2d 4c 69 6e 6b
[SN] Serial number: DGE530TB3958D
[CP] Extended capability: 01 10 cc 03
[RV] Reserved: checksum good, 31 byte(s) reserved
Read/write fields:
[RW] Read-write area: 121 byte(s) free
End
Kernel driver in use: skge
01:08.0 Multimedia controller [0480]: Philips Semiconductors SAA7130 Video
Broadcast Decoder [1131:7130] (rev 01)
Subsystem: Animation Technologies Inc. LifeView FlyVIDEO2000 [5168:0138]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d910a000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=3 PME-
Kernel driver in use: saa7134
01:09.0 Ethernet controller [0200]: Intel Corporation 82557/8/9/0/1 Ethernet
Pro 100 [8086:1229] (rev 02)
Subsystem: IBM 82558B Ethernet Pro 10/100 [1014:005c]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2000ns min, 14000ns max)
Interrupt: pin A routed to IRQ 17
Region 0: Memory at da000000 (32-bit, prefetchable) [size=4K]
Region 1: I/O ports at 9800 [size=32]
Region 2: Memory at d9000000 (32-bit, non-prefetchable) [size=1M]
[virtual] Expansion ROM at da100000 [disabled] [size=1M]
Kernel driver in use: e100
01:0a.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6105/VT6106S
[Rhine-III] [1106:3106] (rev 8b)
Subsystem: D-Link System Inc Device [1186:1405]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 9c00 [size=256]
Region 1: Memory at d9109000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: via-rhine
01:0b.0 Ethernet controller [0200]: D-Link System Inc DGE-530T Gigabit Ethernet
Adapter (rev 11) [1186:4b01] (rev 11)
Subsystem: D-Link System Inc DGE-530T Gigabit Ethernet Adapter (rev 11)
[1186:4b01]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (5750ns min, 7750ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at d9104000 (32-bit, non-prefetchable) [size=16K]
Region 1: I/O ports at a000 [size=256]
[virtual] Expansion ROM at da060000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Product Name: DGE-530T Gigabit Ethernet Adapter
Read-only fields:
[PN] Part number: DGE-530T
[EC] Engineering changes: Rev. 1.1
[MN] Manufacture ID: 44 2d 4c 69 6e 6b
[SN] Serial number: DGE530T9837C3
[CP] Extended capability: 01 10 cc 03
[RV] Reserved: checksum good, 31 byte(s) reserved
Read/write fields:
[RW] Read-write area: 121 byte(s) free
End
Kernel driver in use: skge
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
-- System Information:
Debian Release: wheezy/sid
APT prefers unstable
APT policy: (500, 'unstable')
Architecture: i386 (i686)
Kernel: Linux 3.3.5-030305-generic-pae (SMP w/1 CPU core)
Locale: LANG=ru_RU.UTF-8, LC_CTYPE=ru_RU.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-3.2.0-2-686-pae depends on:
ii debconf [debconf-2.0] 1.5.43
ii initramfs-tools [linux-initramfs-tool] 0.102
ii kmod 6-2
ii linux-base 3.5
ii module-init-tools 6-2
ii yaird [linux-initramfs-tool] 0.0.13-5
Versions of packages linux-image-3.2.0-2-686-pae recommends:
ii firmware-linux-free 3
ii libc6-i686 2.13-32
Versions of packages linux-image-3.2.0-2-686-pae suggests:
pn grub-pc 1.99-21
pn linux-doc-3.2 <none>
Versions of packages linux-image-3.2.0-2-686-pae is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux 0.35
pn firmware-linux-nonfree 0.35
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.2.0-2-686-pae/postinst/depmod-error-initrd-3.2.0-2-686-pae:
false
linux-image-3.2.0-2-686-pae/postinst/missing-firmware-3.2.0-2-686-pae:
linux-image-3.2.0-2-686-pae/prerm/removing-running-kernel-3.2.0-2-686-pae:
true
linux-image-3.2.0-2-686-pae/postinst/ignoring-ramdisk:
--
To UNSUBSCRIBE, email to debian-kernel-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
Archive:
http://lists.debian.org/20120511005044.19259.56136.report...@srv.n-agansk.ru
