Package: linux-2.6
Version: 3.2.10-1
Severity: important
Tags: lfs
When trying to boot
the 3.2.0-2-rt-686 kernel on my machine it freezes most of the time. In
particular just after grub finishes loading the kernel and the initrd and
proceeds to boot the kernel the message "Loading Linux" or something of that
sort appears, the cursor blinks a couple of times (so far everything as usual)
but then the cursor stops blinking and disappears completely and the system is
completely unresponsive. Caps Lock, alt+sysrq+... and other keys don't have any
effect.
Normally, the message that appears immediately after this on my pc, when a
normal kernel is run, is a debug message from udev (I think) described in:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=654282
but that is NOT fatal and is present on all kernels (even the non rt ones).
However in this case nothing of the sort is displayed.
This problem seems very similar to the one in bug report 63269:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=663269
that has been said to be fixed. As a matter of fact I have noticed one
difference:
with version 3.2.10-1 (current), if I load a normal, non-rt kernel first then
restart my pc and load the rt kernel the machine usually starts and doesn't
hang and works perfectly, while normally (for example running the rt kernel for
two times in a row) causes the machine to freeze. On the other hand, with
version 3.2.9-1 there was absolutely nothing to be done to make the machine
boot with the rt-kernel.
This strange behaviour makes me suspect that something may depend on the way
grub is booting the kernel (maybe some options that persist across boots).
However I have no idea how to debug this. If someone gives me some hints I
would be willing to provide any additional information.
-- Package-specific info:
** Kernel log: boot messages should be attached
** Model information
not available
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82855PM Processor to I/O
Controller [8086:3340] (rev 03)
Subsystem: IBM Thinkpad T40 series [1014:0529]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:01.0 PCI bridge [0604]: Intel Corporation 82855PM Processor to AGP
Controller [8086:3341] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 96
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 00003000-00003fff
Memory behind bridge: c0100000-c01fffff
Prefetchable memory behind bridge: e0000000-e7ffffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:1d.0 USB controller [0c03]: Intel Corporation 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 [8086:24c2] (rev 01) (prog-if 00
[UHCI])
Subsystem: IBM ThinkPad [1014:052d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 4: I/O ports at 1800 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB controller [0c03]: Intel Corporation 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 [8086:24c4] (rev 01) (prog-if 00
[UHCI])
Subsystem: IBM ThinkPad [1014:052d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 4: I/O ports at 1820 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB controller [0c03]: Intel Corporation 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 [8086:24c7] (rev 01) (prog-if 00
[UHCI])
Subsystem: IBM ThinkPad [1014:052d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 11
Region 4: I/O ports at 1840 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB controller [0c03]: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2
EHCI Controller [8086:24cd] (rev 01) (prog-if 20 [EHCI])
Subsystem: IBM ThinkPad [1014:052e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 11
Region 0: Memory at c0000000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge
[8086:2448] (rev 81) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR+ INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=08, sec-latency=64
I/O behind bridge: 00004000-00008fff
Memory behind bridge: c0200000-cfffffff
Prefetchable memory behind bridge: e8000000-efffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:1f.0 ISA bridge [0601]: Intel Corporation 82801DBM (ICH4-M) LPC Interface
Bridge [8086:24cc] (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:1f.1 IDE interface [0101]: Intel Corporation 82801DBM (ICH4-M) IDE
Controller [8086:24ca] (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: IBM ThinkPad [1014:052d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 1860 [size=16]
Region 5: Memory at 30000000 (32-bit, non-prefetchable) [size=1K]
Kernel driver in use: ata_piix
00:1f.3 SMBus [0c05]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M)
SMBus Controller [8086:24c3] (rev 01)
Subsystem: IBM ThinkPad [1014:052d]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 5
Region 4: I/O ports at 1880 [size=32]
Kernel driver in use: i801_smbus
00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller [8086:24c5] (rev 01)
Subsystem: IBM ThinkPad T41 [1014:0537]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 5
Region 0: I/O ports at 1c00 [size=256]
Region 1: I/O ports at 18c0 [size=64]
Region 2: Memory at c0000c00 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at c0000800 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: snd_intel8x0
00:1f.6 Modem [0703]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M)
AC'97 Modem Controller [8086:24c6] (rev 01) (prog-if 00 [Generic])
Subsystem: IBM ThinkPad [1014:0525]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 5
Region 0: I/O ports at 2400 [size=256]
Region 1: I/O ports at 2000 [size=128]
Capabilities: <access denied>
Kernel driver in use: snd_intel8x0m
01:00.0 VGA compatible controller [0300]: ATI Technologies Inc Radeon Mobility
M7 LW [Radeon Mobility 7500] [1002:4c57] (prog-if 00 [VGA controller])
Subsystem: IBM ThinkPad T42 2373-4WU [1014:0530]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR+ FastB2B+ DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 66 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 3000 [size=256]
Region 2: Memory at c0100000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at c0120000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: radeon
02:00.0 CardBus bridge [0607]: Texas Instruments PCI4520 PC card Cardbus
Controller [104c:ac46] (rev 01)
Subsystem: IBM ThinkPad [1014:0552]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at b0000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: cc000000-cffff000 (prefetchable)
Memory window 1: c8000000-cbfff000
I/O window 0: 00004c00-00004cff
I/O window 1: 00004800-000048ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
02:00.1 CardBus bridge [0607]: Texas Instruments PCI4520 PC card Cardbus
Controller [104c:ac46] (rev 01)
Subsystem: IBM ThinkPad [1014:0552]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 5
Region 0: Memory at b1000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=07, subordinate=07, sec-latency=176
Memory window 0: ec000000-effff000 (prefetchable)
Memory window 1: c4000000-c7fff000
I/O window 0: 00004400-000044ff
I/O window 1: 00004000-000040ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
02:01.0 Ethernet controller [0200]: Intel Corporation 82540EP Gigabit Ethernet
Controller (Mobile) [8086:101e] (rev 03)
Subsystem: IBM Thinkpad [1014:0549]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (63750ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at c0220000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at c0200000 (32-bit, non-prefetchable) [size=64K]
Region 2: I/O ports at 8000 [size=64]
[virtual] Expansion ROM at e8000000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: e1000
02:02.0 Network controller [0280]: Intel Corporation PRO/Wireless LAN 2100 3B
Mini PCI Adapter [8086:1043] (rev 04)
Subsystem: Intel Corporation Device [8086:2551]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min, 8500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at c0210000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ipw2100
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 1058:1001 Western Digital Technologies, Inc. External
Hard Disk [Elements]
Bus 003 Device 003: ID 073a:2230 Chaplet Systems, Inc. infrared dongle for
remote
-- System Information:
Debian Release: wheezy/sid
APT prefers unstable
APT policy: (500, 'unstable'), (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 3.2.0-2-686-pae (SMP w/1 CPU core)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.2.0-2-rt-686-pae depends on:
ii debconf [debconf-2.0] 1.5.42
ii initramfs-tools [linux-initramfs-tool] 0.101
ii kmod 6-2
ii linux-base 3.5
ii module-init-tools 6-2
Versions of packages linux-image-3.2.0-2-rt-686-pae recommends:
ii firmware-linux-free 3
ii libc6-i686 2.13-27
Versions of packages linux-image-3.2.0-2-rt-686-pae suggests:
ii grub-pc 1.99-17
ii linux-doc-3.2 3.2.10-1
Versions of packages linux-image-3.2.0-2-rt-686-pae is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 0.35
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux 0.35
pn firmware-linux-nonfree 0.35
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.2.0-2-rt-686-pae/postinst/ignoring-ramdisk:
linux-image-3.2.0-2-rt-686-pae/postinst/depmod-error-initrd-3.2.0-2-rt-686-pae:
false
linux-image-3.2.0-2-rt-686-pae/prerm/removing-running-kernel-3.2.0-2-rt-686-pae:
true
linux-image-3.2.0-2-rt-686-pae/postinst/missing-firmware-3.2.0-2-rt-686-pae:
#
# DO NOT EDIT THIS FILE
#
# It is automatically generated by grub-mkconfig using templates
# from /etc/grub.d and settings from /etc/default/grub
#
### BEGIN /etc/grub.d/00_header ###
if [ -s $prefix/grubenv ]; then
load_env
fi
set default="${saved_entry}"
if [ "${prev_saved_entry}" ]; then
set saved_entry="${prev_saved_entry}"
save_env saved_entry
set prev_saved_entry=
save_env prev_saved_entry
set boot_once=true
fi
function savedefault {
if [ -z "${boot_once}" ]; then
saved_entry="${chosen}"
save_env saved_entry
fi
}
function load_video {
insmod vbe
insmod vga
insmod video_bochs
insmod video_cirrus
}
insmod part_msdos
insmod ext2
set root='(hd0,msdos1)'
search --no-floppy --fs-uuid --set=root 5a0ffa6d-f75b-430d-af8d-a77bfe7214e8
if loadfont /usr/share/grub/unicode.pf2 ; then
set gfxmode=1024x768x16
load_video
insmod gfxterm
insmod part_msdos
insmod ext2
set root='(hd0,msdos1)'
search --no-floppy --fs-uuid --set=root 5a0ffa6d-f75b-430d-af8d-a77bfe7214e8
set locale_dir=($root)/boot/grub/locale
set lang=en_US
insmod gettext
fi
terminal_output gfxterm
set timeout=2
### END /etc/grub.d/00_header ###
### BEGIN /etc/grub.d/05_debian_theme ###
insmod part_msdos
insmod ext2
set root='(hd0,msdos1)'
search --no-floppy --fs-uuid --set=root 5a0ffa6d-f75b-430d-af8d-a77bfe7214e8
insmod png
if background_image /usr/share/images/desktop-base/spacefun-grub.png; then
set color_normal=light-gray/black
set color_highlight=white/black
else
set menu_color_normal=cyan/blue
set menu_color_highlight=white/blue
fi
### END /etc/grub.d/05_debian_theme ###
### BEGIN /etc/grub.d/10_linux ###
menuentry 'Debian GNU/Linux, with Linux 3.2.0-2-rt-686-pae' --class debian
--class gnu-linux --class gnu --class os {
savedefault
load_video
set gfxpayload=keep
insmod gzio
insmod part_msdos
insmod ext2
set root='(hd0,msdos1)'
search --no-floppy --fs-uuid --set=root
5a0ffa6d-f75b-430d-af8d-a77bfe7214e8
echo 'Loading Linux 3.2.0-2-rt-686-pae ...'
linux /boot/vmlinuz-3.2.0-2-rt-686-pae
root=UUID=5a0ffa6d-f75b-430d-af8d-a77bfe7214e8 ro quiet
echo 'Loading initial ramdisk ...'
initrd /boot/initrd.img-3.2.0-2-rt-686-pae
}
menuentry 'Debian GNU/Linux, with Linux 3.2.0-2-rt-686-pae (recovery mode)'
--class debian --class gnu-linux --class gnu --class os {
load_video
set gfxpayload=keep
insmod gzio
insmod part_msdos
insmod ext2
set root='(hd0,msdos1)'
search --no-floppy --fs-uuid --set=root
5a0ffa6d-f75b-430d-af8d-a77bfe7214e8
echo 'Loading Linux 3.2.0-2-rt-686-pae ...'
linux /boot/vmlinuz-3.2.0-2-rt-686-pae
root=UUID=5a0ffa6d-f75b-430d-af8d-a77bfe7214e8 ro single
echo 'Loading initial ramdisk ...'
initrd /boot/initrd.img-3.2.0-2-rt-686-pae
}
menuentry 'Debian GNU/Linux, with Linux 3.2.0-2-686-pae' --class debian --class
gnu-linux --class gnu --class os {
savedefault
load_video
set gfxpayload=keep
insmod gzio
insmod part_msdos
insmod ext2
set root='(hd0,msdos1)'
search --no-floppy --fs-uuid --set=root
5a0ffa6d-f75b-430d-af8d-a77bfe7214e8
echo 'Loading Linux 3.2.0-2-686-pae ...'
linux /boot/vmlinuz-3.2.0-2-686-pae
root=UUID=5a0ffa6d-f75b-430d-af8d-a77bfe7214e8 ro quiet
echo 'Loading initial ramdisk ...'
initrd /boot/initrd.img-3.2.0-2-686-pae
}
menuentry 'Debian GNU/Linux, with Linux 3.2.0-2-686-pae (recovery mode)'
--class debian --class gnu-linux --class gnu --class os {
load_video
set gfxpayload=keep
insmod gzio
insmod part_msdos
insmod ext2
set root='(hd0,msdos1)'
search --no-floppy --fs-uuid --set=root
5a0ffa6d-f75b-430d-af8d-a77bfe7214e8
echo 'Loading Linux 3.2.0-2-686-pae ...'
linux /boot/vmlinuz-3.2.0-2-686-pae
root=UUID=5a0ffa6d-f75b-430d-af8d-a77bfe7214e8 ro single
echo 'Loading initial ramdisk ...'
initrd /boot/initrd.img-3.2.0-2-686-pae
}
menuentry 'Debian GNU/Linux, with Linux 3.2.0-1-686-pae' --class debian --class
gnu-linux --class gnu --class os {
savedefault
load_video
set gfxpayload=keep
insmod gzio
insmod part_msdos
insmod ext2
set root='(hd0,msdos1)'
search --no-floppy --fs-uuid --set=root
5a0ffa6d-f75b-430d-af8d-a77bfe7214e8
echo 'Loading Linux 3.2.0-1-686-pae ...'
linux /boot/vmlinuz-3.2.0-1-686-pae
root=UUID=5a0ffa6d-f75b-430d-af8d-a77bfe7214e8 ro quiet
echo 'Loading initial ramdisk ...'
initrd /boot/initrd.img-3.2.0-1-686-pae
}
menuentry 'Debian GNU/Linux, with Linux 3.2.0-1-686-pae (recovery mode)'
--class debian --class gnu-linux --class gnu --class os {
load_video
set gfxpayload=keep
insmod gzio
insmod part_msdos
insmod ext2
set root='(hd0,msdos1)'
search --no-floppy --fs-uuid --set=root
5a0ffa6d-f75b-430d-af8d-a77bfe7214e8
echo 'Loading Linux 3.2.0-1-686-pae ...'
linux /boot/vmlinuz-3.2.0-1-686-pae
root=UUID=5a0ffa6d-f75b-430d-af8d-a77bfe7214e8 ro single
echo 'Loading initial ramdisk ...'
initrd /boot/initrd.img-3.2.0-1-686-pae
}
menuentry 'Debian GNU/Linux, with Linux 3.1.0-1-686-pae' --class debian --class
gnu-linux --class gnu --class os {
savedefault
load_video
set gfxpayload=keep
insmod gzio
insmod part_msdos
insmod ext2
set root='(hd0,msdos1)'
search --no-floppy --fs-uuid --set=root
5a0ffa6d-f75b-430d-af8d-a77bfe7214e8
echo 'Loading Linux 3.1.0-1-686-pae ...'
linux /boot/vmlinuz-3.1.0-1-686-pae
root=UUID=5a0ffa6d-f75b-430d-af8d-a77bfe7214e8 ro quiet
echo 'Loading initial ramdisk ...'
initrd /boot/initrd.img-3.1.0-1-686-pae
}
menuentry 'Debian GNU/Linux, with Linux 3.1.0-1-686-pae (recovery mode)'
--class debian --class gnu-linux --class gnu --class os {
load_video
set gfxpayload=keep
insmod gzio
insmod part_msdos
insmod ext2
set root='(hd0,msdos1)'
search --no-floppy --fs-uuid --set=root
5a0ffa6d-f75b-430d-af8d-a77bfe7214e8
echo 'Loading Linux 3.1.0-1-686-pae ...'
linux /boot/vmlinuz-3.1.0-1-686-pae
root=UUID=5a0ffa6d-f75b-430d-af8d-a77bfe7214e8 ro single
echo 'Loading initial ramdisk ...'
initrd /boot/initrd.img-3.1.0-1-686-pae
}
### END /etc/grub.d/10_linux ###
### BEGIN /etc/grub.d/20_linux_xen ###
### END /etc/grub.d/20_linux_xen ###
### BEGIN /etc/grub.d/30_os-prober ###
### END /etc/grub.d/30_os-prober ###
### BEGIN /etc/grub.d/40_custom ###
# This file provides an easy way to add custom menu entries. Simply type the
# menu entries you want to add after this comment. Be careful not to change
# the 'exec tail' line above.
### END /etc/grub.d/40_custom ###
### BEGIN /etc/grub.d/41_custom ###
if [ -f $prefix/custom.cfg ]; then
source $prefix/custom.cfg;
fi
### END /etc/grub.d/41_custom ###
