Package: linux-2.6
Version: 2.6.32-39squeeze1
Severity: important
At boot time, using a fresh install, the kernel pauses for a great while during
boot
until finally displaying this message:
gave up waiting for init of module bttv
I first saw this problem after a routine synaptic update to the latest linux
version in
squeeze. Something broke. After much trial and error it appears to be some
sort
of race condition to do with the drm driver. Creating the file
/etc/modprobe.d/bttv.conf
with this content:
softdep bttv post: drm
softdep bt878 post: drm
then update-grub2
resolves the problem. HTH!
Harry Coin
-- Package-specific info:
** Version:
Linux version 2.6.32-5-686 (Debian 2.6.32-39squeeze1) (da...@debian.org) (gcc
version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Wed Jan 11 12:29:30 UTC 2012
** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-686
root=UUID=1dc4aa1d-dfd7-4b81-85eb-0a6124a811b7 ro ipv6.disable=1
** Tainted: P (1)
* Proprietary module has been loaded.
** Kernel log:
[ 36.043365] bttv1: Bt878 (rev 17) at 0000:05:0d.0, irq: 22, latency: 66,
mmio: 0xc8502000
[ 36.043542] bttv1: detected: DViCO FusionHDTV 5 Lite [card=135], PCI
subsystem ID is 18ac:d500
[ 36.043617] bttv1: using: DViCO FusionHDTV 5 Lite [card=135,autodetected]
[ 36.043684] IRQ 22/bttv1: IRQF_DISABLED is not guaranteed on shared IRQs
[ 36.043785] bttv1: gpio: en=00000000, out=00000000 in=00ffffff [init]
[ 36.043937] bttv1: tuner type=64
[ 36.052729] bttv1: audio absent, no audio device found!
[ 36.057359] tuner 1-0043: chip found @ 0x86 (bt878 #1 [sw])
[ 36.057531] tda9887 1-0043: creating new instance
[ 36.057596] tda9887 1-0043: tda988[5/6/7] found
[ 36.061193] tuner 1-0061: chip found @ 0xc2 (bt878 #1 [sw])
[ 36.061661] tuner-simple 1-0061: creating new instance
[ 36.061728] tuner-simple 1-0061: type set to 64 (LG TDVS-H06xF)
[ 36.062999] bttv1: registered device video1
[ 36.063158] bttv1: registered device vbi1
[ 36.064494] bttv1: add subdevice "dvb1"
[ 36.451855] bt878: AUDIO driver version 0.0.0 loaded
[ 36.451974] bt878: Bt878 AUDIO function found (0).
[ 36.452105] bt878 0000:05:0a.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 36.452183] bt878_probe: card id=[0xd50018ac],[ DViCO FusionHDTV 5 Lite ]
has DVB functions.
[ 36.452403] bt878(0): Bt878 (rev 17) at 05:0a.1, irq: 18, latency: 66,
memory: 0xc8501000
[ 36.452599] IRQ 18/bt878: IRQF_DISABLED is not guaranteed on shared IRQs
[ 36.452955] bt878: Bt878 AUDIO function found (1).
[ 36.453038] bt878 0000:05:0d.1: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 36.453108] bt878_probe: card id=[0xd50018ac],[ DViCO FusionHDTV 5 Lite ]
has DVB functions.
[ 36.453193] bt878(1): Bt878 (rev 17) at 05:0d.1, irq: 22, latency: 66,
memory: 0xc8503000
[ 36.453670] IRQ 22/bt878: IRQF_DISABLED is not guaranteed on shared IRQs
[ 36.758829] DVB: registering new adapter (bttv0)
[ 37.017174] tuner-simple 0-0061: attaching existing instance
[ 37.017252] tuner-simple 0-0061: type set to 64 (LG TDVS-H06xF)
[ 37.017323] DVB: registering adapter 0 frontend 0 (LG Electronics LGDT3303
VSB/QAM Frontend)...
[ 37.018338] DVB: registering new adapter (bttv1)
[ 37.229528] tuner-simple 1-0061: attaching existing instance
[ 37.229601] tuner-simple 1-0061: type set to 64 (LG TDVS-H06xF)
[ 37.229671] DVB: registering adapter 1 frontend 0 (LG Electronics LGDT3303
VSB/QAM Frontend)...
[ 37.308027] floppy0: no floppy controllers found
[ 37.461405] md: md0 stopped.
[ 37.465490] md: bind<sdb1>
[ 37.490170] md: raid1 personality registered for level 1
[ 37.490695] raid1: raid set md0 active with 1 out of 2 mirrors
[ 37.490811] md0: detected capacity change from 0 to 9998098432
[ 37.493653] md0: unknown partition table
[ 37.843255] Adding 4002808k swap on /dev/sda5. Priority:-1 extents:1
across:4002808k
[ 38.175697] EXT3 FS on sda1, internal journal
[ 38.260247] loop: module loaded
[ 39.967389] EXT4-fs (sdb2): mounted filesystem with ordered data mode
[ 39.988910] EXT4-fs (sdc2): mounted filesystem with ordered data mode
[ 40.077978] kjournald starting. Commit interval 5 seconds
[ 40.078217] EXT3 FS on sda7, internal journal
[ 40.078335] EXT3-fs: mounted filesystem with ordered data mode.
[ 40.183473] kjournald starting. Commit interval 5 seconds
[ 40.183714] EXT3 FS on sda6, internal journal
[ 40.183832] EXT3-fs: mounted filesystem with ordered data mode.
[ 40.208761] EXT4-fs (md0): mounted filesystem with ordered data mode
[ 41.670287] fuse init (API version 7.13)
[ 42.535357] RPC: Registered udp transport module.
[ 42.535427] RPC: Registered tcp transport module.
[ 42.535491] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 42.769204] Installing knfsd (copyright (C) 1996 o...@monad.swb.de).
[ 43.086381] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery
directory
[ 43.107350] NFSD: starting 90-second grace period
[ 44.508389] tg3 0000:05:02.0: firmware: requesting tigon/tg3_tso.bin
[ 47.516271] Bluetooth: Core ver 2.15
[ 47.516368] NET: Registered protocol family 31
[ 47.516371] Bluetooth: HCI device and connection manager initialized
[ 47.516376] Bluetooth: HCI socket layer initialized
[ 47.679190] Bluetooth: L2CAP ver 2.14
[ 47.679197] Bluetooth: L2CAP socket layer initialized
[ 47.716365] Bluetooth: RFCOMM TTY layer initialized
[ 47.716374] Bluetooth: RFCOMM socket layer initialized
[ 47.716378] Bluetooth: RFCOMM ver 1.11
[ 47.757136] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 47.757144] Bluetooth: BNEP filters: protocol multicast
[ 47.877792] Bridge firewalling registered
[ 47.955361] tg3 0000:05:02.0: eth0: Link is up at 1000 Mbps, full duplex
[ 47.955368] tg3 0000:05:02.0: eth0: Flow control is on for TX and on for RX
[ 48.160252] Bluetooth: SCO (Voice Link) ver 0.6
[ 48.160258] Bluetooth: SCO socket layer initialized
[ 48.922053] lp0: using parport0 (interrupt-driven).
[ 49.114183] ppdev: user-space parallel port driver
[ 59.728150] CPU0 attaching NULL sched-domain.
[ 59.728165] CPU1 attaching NULL sched-domain.
[ 59.768595] CPU0 attaching sched-domain:
[ 59.768602] domain 0: span 0-1 level CPU
[ 59.768607] groups: group c28037e4 cpus 0 group c29037e4 cpus 1
[ 59.768618] CPU1 attaching sched-domain:
[ 59.768622] domain 0: span 0-1 level CPU
[ 59.768626] groups: group c29037e4 cpus 1 group c28037e4 cpus 0
[ 400.605505] mtrr: no MTRR for c0000000,2000000 found
[ 445.229078] agpgart-intel 0000:00:00.0: AGP 3.0 bridge
[ 445.229098] agpgart-intel 0000:00:00.0: bridge is in legacy mode, falling
back to 2.x
[ 445.229108] agpgart-intel 0000:00:00.0: putting AGP V2 device into 4x mode
[ 445.229152] nvidia 0000:01:00.0: putting AGP V2 device into 4x mode
[ 1242.721723] agpgart-intel 0000:00:00.0: AGP 3.0 bridge
[ 1242.721746] agpgart-intel 0000:00:00.0: bridge is in legacy mode, falling
back to 2.x
[ 1242.721756] agpgart-intel 0000:00:00.0: putting AGP V2 device into 4x mode
[ 1242.721800] nvidia 0000:01:00.0: putting AGP V2 device into 4x mode
[ 5889.952930] tg3 0000:05:02.0: eth0: Link is down
[ 5910.620596] tg3 0000:05:02.0: eth0: Link is up at 1000 Mbps, full duplex
[ 5910.620603] tg3 0000:05:02.0: eth0: Flow control is on for TX and on for RX
** Model information
not available
** Loaded modules:
Module Size Used by
speedstep_lib 2468 0
cpufreq_stats 1997 0
cpufreq_conservative 4018 0
cpufreq_userspace 1488 0
cpufreq_powersave 602 0
ppdev 4058 0
lp 5570 0
sco 5885 2
bridge 33063 0
stp 996 1 bridge
bnep 7468 2
rfcomm 25215 0
l2cap 21721 6 bnep,rfcomm
bluetooth 36335 6 sco,bnep,rfcomm,l2cap
rfkill 10280 3 bluetooth
nfsd 194111 11
binfmt_misc 4915 1
lockd 49481 1 nfsd
nfs_acl 1695 1 nfsd
auth_rpcgss 25312 1 nfsd
sunrpc 134952 10 nfsd,lockd,nfs_acl,auth_rpcgss
exportfs 2626 1 nfsd
fuse 44316 1
ext4 257032 3
jbd2 56219 1 ext4
crc16 1027 2 l2cap,ext4
loop 9777 0
raid1 16383 1
md_mod 67401 2 raid1
lgdt330x 5686 2
dvb_bt8xx 9551 0
dvb_core 62666 2 lgdt330x,dvb_bt8xx
bt878 5850 1 dvb_bt8xx
tuner_simple 9694 4
tuner_types 7537 1 tuner_simple
tda9887 6997 2
tda8290 7865 0
drm 112040 0
tuner 14428 4
tvaudio 19196 0
bttv 88197 2 dvb_bt8xx,bt878
snd_intel8x0 19595 1
v4l2_common 9836 3 tuner,tvaudio,bttv
videodev 25629 4 tuner,tvaudio,bttv,v4l2_common
snd_ac97_codec 79200 1 snd_intel8x0
v4l1_compat 10250 1 videodev
ac97_bus 710 1 snd_ac97_codec
ir_common 22187 1 bttv
snd_pcm 47226 2 snd_intel8x0,snd_ac97_codec
i2c_algo_bit 3497 1 bttv
nvidia 4651189 22
videobuf_dma_sg 7227 1 bttv
snd_seq 35495 0
videobuf_core 10484 2 bttv,videobuf_dma_sg
btcx_risc 2507 1 bttv
tveeprom 9393 1 bttv
snd_timer 12270 2 snd_pcm,snd_seq
i2c_core 12795 14
lgdt330x,dvb_bt8xx,tuner_simple,tda9887,tda8290,drm,tuner,tvaudio,bttv,v4l2_common,videodev,i2c_algo_bit,nvidia,tveeprom
snd_seq_device 3673 1 snd_seq
shpchp 21220 0
snd 34431 8
snd_intel8x0,snd_ac97_codec,snd_pcm,snd_seq,snd_timer,snd_seq_device
soundcore 3450 1 snd
parport_pc 15799 1
pci_hotplug 18545 1 shpchp
evdev 5609 7
snd_page_alloc 5061 2 snd_intel8x0,snd_pcm
parport 22554 3 ppdev,lp,parport_pc
rng_core 2178 0
pcspkr 1207 0
psmouse 44817 0
processor 26343 0
button 3598 0
serio_raw 2916 0
ext3 94484 3
jbd 32365 1 ext3
mbcache 3762 2 ext4,ext3
sd_mod 26029 10
crc_t10dif 1012 1 sd_mod
ata_generic 2247 0
thermal 9206 0
ata_piix 17744 4
sata_sil 5620 3
uhci_hcd 16073 0
libata 115925 3 ata_generic,ata_piix,sata_sil
aic79xx 112204 0
scsi_transport_spi 14874 1 aic79xx
tg3 95905 0
libphy 11646 1 tg3
ehci_hcd 28749 0
scsi_mod 104909 4 sd_mod,libata,aic79xx,scsi_transport_spi
usbcore 99017 3 uhci_hcd,ehci_hcd
nls_base 4541 1 usbcore
thermal_sys 9378 2 processor,thermal
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
allow-hotplug eth0
#NetworkManager#iface eth0 inet dhcp
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
link/ether 00:0b:cd:92:d0:7c brd ff:ff:ff:ff:ff:ff
inet 192.168.11.35/24 brd 192.168.11.255 scope global eth0
3: pan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN
link/ether ca:64:e2:32:9a:8f brd ff:ff:ff:ff:ff:ff
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes
packets errs drop fifo colls carrier compressed
lo: 8804 104 0 0 0 0 0 0 8804
104 0 0 0 0 0 0
eth0:37078859 35092 0 0 0 0 0 22 1631992
21376 0 0 0 0 0 0
pan0: 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0
*** Protocol statistics:
Ip:
35178 total packets received
6 with invalid addresses
0 forwarded
0 incoming packets discarded
35172 incoming packets delivered
21427 requests sent out
Icmp:
5 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
echo requests: 1
echo replies: 4
38 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
echo request: 37
echo replies: 1
IcmpMsg:
InType0: 4
InType8: 1
OutType0: 1
OutType8: 37
Tcp:
100 active connections openings
2 passive connection openings
3 failed connection attempts
8 connection resets received
0 connections established
33349 segments received
20618 segments send out
5 segments retransmited
0 bad segments received.
38 resets sent
Udp:
2712 packets received
0 packets to unknown port received.
0 packet receive errors
760 packets sent
UdpLite:
TcpExt:
28 TCP sockets finished time wait in fast timer
658 delayed acks sent
1 delayed acks further delayed because of locked socket
183 packets directly queued to recvmsg prequeue.
153012 bytes directly received in process context from prequeue
31272 packet headers predicted
99 packets header predicted and directly queued to user
205 acknowledgments not containing data payload received
61 predicted acknowledgments
3 other TCP timeouts
11 connections reset due to unexpected data
7 connections reset due to early user close
2 connections aborted due to timeout
IpExt:
InMcastPkts: 42
OutMcastPkts: 24
InBcastPkts: 1094
OutBcastPkts: 86
InOctets: 36465025
OutOctets: 1251900
InMcastOctets: 4428
OutMcastOctets: 3932
InBcastOctets: 100791
OutBcastOctets: 10956
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation E7505 Memory Controller Hub
[8086:2550] (rev 03)
Subsystem: Hewlett-Packard Company Device [103c:00cc]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [40] Vendor Specific Information: Len=04 <?>
Capabilities: [a0] AGP version 3.0
Status: RQ=32 Iso- ArqSz=2 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP+ GART64- 64bit- FW- Rate=x4
Kernel driver in use: agpgart-intel
00:01.0 PCI bridge [0604]: Intel Corporation E7505/E7205 PCI-to-AGP Bridge
[8086:2552] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 64
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
Memory behind bridge: c9000000-ca1fffff
Prefetchable memory behind bridge: c0000000-c81fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [60] AGP3 <?>
00:1d.0 USB Controller [0c03]: Intel Corporation 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 [8086:24c2] (rev 01) (prog-if 00
[UHCI])
Subsystem: Hewlett-Packard Company Device [103c:00cc]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at 3440 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 [8086:24c4] (rev 01) (prog-if 00
[UHCI])
Subsystem: Hewlett-Packard Company Device [103c:00cc]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 3460 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2
EHCI Controller [8086:24cd] (rev 01) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Device [103c:00cc]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 0: Memory at c8a00000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=0080
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev
81) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=64
I/O behind bridge: 00001000-00002fff
Memory behind bridge: c8200000-c84fffff
Prefetchable memory behind bridge: c8500000-c87fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:1f.0 ISA bridge [0601]: Intel Corporation 82801DB/DBL (ICH4/ICH4-L) LPC
Interface Bridge [8086:24c0] (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:1f.1 IDE interface [0101]: Intel Corporation 82801DB (ICH4) IDE Controller
[8086:24cb] (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: Hewlett-Packard Company Device [103c:00cc]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 34a0 [size=16]
Region 5: Memory at 80100000 (32-bit, non-prefetchable) [size=1K]
Kernel driver in use: ata_piix
00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller [8086:24c5] (rev 01)
Subsystem: Hewlett-Packard Company Device [103c:00c3]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at 3000 [size=256]
Region 1: I/O ports at 3400 [size=64]
Region 2: Memory at c8a00400 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at c8a00600 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: Intel ICH
01:00.0 VGA compatible controller [0300]: nVidia Corporation NV11GL [Quadro2
MXR/EX/Go] [10de:0113] (rev b2) (prog-if 00 [VGA controller])
Subsystem: nVidia Corporation Device [10de:0070]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 248 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 16
Region 0: Memory at c9000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at c0000000 (32-bit, prefetchable) [size=128M]
[virtual] Expansion ROM at c8000000 [disabled] [size=64K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans-
64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=32 ArqSz=0 Cal=0 SBA- AGP+ GART64- 64bit- FW-
Rate=x4
Kernel driver in use: nvidia
05:02.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5702X
Gigabit Ethernet [14e4:16a6] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:00cc]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (16000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at c8400000 (64-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at c8510000 [disabled] [size=64K]
Capabilities: [40] PCI-X non-bridge device
Command: DPERE- ERO+ RBC=512 OST=1
Status: Dev=ff:1f.1 64bit+ 133MHz+ SCD- USC- DC=simple
DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz-
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Product Name: Broadcom Gigabit Ethernet Controller
Read-only fields:
[PN] Part number: BCM95702A20
[EC] Engineering changes: 106679-15
[SN] Serial number: 0123456789
[MN] Manufacture ID: 31 34 65 34
[RV] Reserved: checksum bad, 35 byte(s) reserved
Read/write fields:
[YA] Asset tag: KKS
[RW] Read-write area: 115 byte(s) free
End
Capabilities: [58] MSI: Enable- Count=1/8 Maskable- 64bit+
Address: 0000000100000000 Data: 41c8
Kernel driver in use: tg3
05:0a.0 Multimedia video controller [0400]: Brooktree Corporation Bt878 Video
Capture [109e:036e] (rev 11)
Subsystem: DViCO Corporation DViCO FusionHDTV5 Lite [18ac:d500]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 66 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 18
Region 0: Memory at c8500000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
No end tag found
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: bttv
05:0a.1 Multimedia controller [0480]: Brooktree Corporation Bt878 Audio Capture
[109e:0878] (rev 11)
Subsystem: DViCO Corporation DViCO FusionHDTV5 Lite [18ac:d500]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 66 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 18
Region 0: Memory at c8501000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
No end tag found
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: bt878
05:0b.0 RAID bus controller [0104]: Silicon Image, Inc. Adaptec AAR-1210SA SATA
HostRAID Controller [1095:0240] (rev 02) (prog-if 01)
Subsystem: Adaptec Device [9005:0240]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at 2010 [size=8]
Region 1: I/O ports at 2020 [size=4]
Region 2: I/O ports at 2018 [size=8]
Region 3: I/O ports at 2024 [size=4]
Region 4: I/O ports at 2000 [size=16]
Region 5: Memory at c8414000 (32-bit, non-prefetchable) [size=512]
[virtual] Expansion ROM at c8580000 [disabled] [size=512K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: sata_sil
05:0c.0 SCSI storage controller [0100]: Adaptec AIC-7902 U320 [9005:801f] (rev
03)
Subsystem: Hewlett-Packard Company Device [103c:00cc]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (10000ns min, 6250ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at 1000 [disabled] [size=256]
Region 1: Memory at c8200000 (64-bit, non-prefetchable) [size=8K]
Region 3: I/O ports at 1400 [disabled] [size=256]
[virtual] Expansion ROM at c8600000 [disabled] [size=512K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a0] MSI: Enable- Count=1/2 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [94] PCI-X non-bridge device
Command: DPERE- ERO+ RBC=512 OST=8
Status: Dev=ff:1f.0 64bit+ 133MHz+ SCD- USC- DC=simple
DMMRBC=512 DMOST=8 DMCRS=16 RSCEM- 266MHz- 533MHz-
Kernel driver in use: aic79xx
05:0c.1 SCSI storage controller [0100]: Adaptec AIC-7902 U320 [9005:801f] (rev
03)
Subsystem: Hewlett-Packard Company Device [103c:00cc]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (10000ns min, 6250ns max), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 22
Region 0: I/O ports at 1800 [disabled] [size=256]
Region 1: Memory at c8202000 (64-bit, non-prefetchable) [size=8K]
Region 3: I/O ports at 1c00 [disabled] [size=256]
[virtual] Expansion ROM at c8680000 [disabled] [size=512K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a0] MSI: Enable- Count=1/2 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [94] PCI-X non-bridge device
Command: DPERE- ERO+ RBC=512 OST=8
Status: Dev=ff:1f.1 64bit+ 133MHz+ SCD- USC- DC=simple
DMMRBC=512 DMOST=8 DMCRS=16 RSCEM- 266MHz- 533MHz-
Kernel driver in use: aic79xx
05:0d.0 Multimedia video controller [0400]: Brooktree Corporation Bt878 Video
Capture [109e:036e] (rev 11)
Subsystem: DViCO Corporation DViCO FusionHDTV5 Lite [18ac:d500]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 66 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at c8502000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
No end tag found
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: bttv
05:0d.1 Multimedia controller [0480]: Brooktree Corporation Bt878 Audio Capture
[109e:0878] (rev 11)
Subsystem: DViCO Corporation DViCO FusionHDTV5 Lite [18ac:d500]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 66 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at c8503000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
No end tag found
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: bt878
** USB devices:
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: 6.0.3
APT prefers stable-updates
APT policy: (500, 'stable-updates'), (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 2.6.32-5-686 (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.32-5-686 depends on:
ii debconf [debconf-2.0] 1.5.36.1 Debian configuration management sy
ii initramfs-tools [linux 0.98.8 tools for generating an initramfs
ii linux-base 2.6.32-39squeeze1 Linux image base package
ii module-init-tools 3.12-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.32-5-686 recommends:
pn firmware-linux-free <none> (no description available)
ii libc6-i686 2.11.2-10 Embedded GNU C Library: Shared lib
Versions of packages linux-image-2.6.32-5-686 suggests:
pn grub | lilo <none> (no description available)
ii linux-doc-2.6.32 2.6.32-39squeeze1 Linux kernel specific documentatio
Versions of packages linux-image-2.6.32-5-686 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
ii firmware-linux-nonfree 0.28+squeeze1 Binary firmware for various driver
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information:
linux-image-2.6.32-5-686/prerm/removing-running-kernel-2.6.32-5-686: true
linux-image-2.6.32-5-686/postinst/depmod-error-initrd-2.6.32-5-686: false
linux-image-2.6.32-5-686/postinst/ignoring-do-bootloader-2.6.32-5-686:
linux-image-2.6.32-5-686/postinst/missing-firmware-2.6.32-5-686:
--
To UNSUBSCRIBE, email to debian-kernel-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
Archive:
http://lists.debian.org/20120123235001.8819.91759.report...@mythmaster.quietfountain.com
