Package: linux-2.6
Version: 3.1.1-1
Severity: normal
Dear Maintainer,
I use the Linux kernel currently provided by the linux-image-2.6.39-2-686-pae.
Sorry, I can't report directly a bug for this package because I encounter a
crash with rebortbug and this package name.
When I reboot, pc displays this message (I copy it manually) and freeze
sometimes :
[...]
Will now restart
[ 840.083295] kvm: exiting hardware virtualization
[ 840.097786] sd 0:0:0:0 [sda] Synchronizing SCSI cache
[ 840.112535] ehci_hcd 0000:00:1d.7: PCI INT D disabled
[ 840.120860] Restarting system.
[ 840.128856] machine restart
[ 840.126945] hub 3-0:1.0: hub_port_status failed (err = -110)
[ 840.140761] hub 3-0:1.0: hub_port_status failed (err = -110)
Despite of two last lines, I don't notice much problem when I
plug/unplug usb device, than I don't use usb.
Sometimes I encounter the same bug when halting, but this it much
exceptional.
Regards,
-- Package-specific info:
** Kernel log: boot messages should be attached
** Model information
not available
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation System Controller Hub (SCH
Poulsbo) [8086:8100] (rev 07)
Subsystem: Intel Corporation Device [8086:8119]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
00:02.0 VGA compatible controller [0300]: Intel Corporation System Controller
Hub (SCH Poulsbo) Graphics Controller [8086:8108] (rev 07) (prog-if 00 [VGA
controller])
Subsystem: Intel Corporation Device [8086:8119]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fe980000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at c880 [size=8]
Region 2: Memory at d0000000 (32-bit, non-prefetchable) [size=256M]
Region 3: Memory at fe940000 (32-bit, non-prefetchable) [size=256K]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
00:1b.0 Audio device [0403]: Intel Corporation System Controller Hub (SCH
Poulsbo) HD Audio Controller [8086:811b] (rev 07)
Subsystem: Intel Corporation Device [8086:8119]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe938000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
00:1c.0 PCI bridge [0604]: Intel Corporation System Controller Hub (SCH
Poulsbo) PCI Express Port 1 [8086:8110] (rev 07) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fea00000-feafffff
Prefetchable memory behind bridge: cff00000-cfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.1 PCI bridge [0604]: Intel Corporation System Controller Hub (SCH
Poulsbo) PCI Express Port 2 [8086:8112] (rev 07) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: feb00000-febfffff
Prefetchable memory behind bridge: 80000000-801fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB Controller [0c03]: Intel Corporation System Controller Hub (SCH
Poulsbo) USB UHCI #1 [8086:8114] (rev 07) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:8119]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at c480 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller [0c03]: Intel Corporation System Controller Hub (SCH
Poulsbo) USB UHCI #2 [8086:8115] (rev 07) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:8119]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at c080 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller [0c03]: Intel Corporation System Controller Hub (SCH
Poulsbo) USB UHCI #3 [8086:8116] (rev 07) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:8119]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at b880 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller [0c03]: Intel Corporation System Controller Hub (SCH
Poulsbo) USB EHCI #1 [8086:8117] (rev 07) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Device [8086:8119]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 0: Memory at fe937c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1f.0 ISA bridge [0601]: Intel Corporation System Controller Hub (SCH
Poulsbo) LPC Bridge [8086:8119] (rev 07)
Subsystem: Intel Corporation System Controller Hub (SCH Poulsbo) LPC
Bridge [8086:8119]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Kernel driver in use: lpc_sch
00:1f.1 IDE interface [0101]: Intel Corporation System Controller Hub (SCH
Poulsbo) IDE Controller [8086:811a] (rev 07) (prog-if 80 [Master])
Subsystem: Intel Corporation Device [8086:8119]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[size=1]
Region 4: I/O ports at ffa0 [size=16]
Kernel driver in use: pata_sch
01:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 02)
Subsystem: Realtek Semiconductor Co., Ltd. TEG-ECTX Gigabit PCI-E
Adapter [Trendnet] [10ec:8168]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 40
Region 0: I/O ports at dd00 [size=256]
Region 2: Memory at feaff000 (64-bit, non-prefetchable) [size=4K]
Region 4: Memory at cfff0000 (64-bit, prefetchable) [size=64K]
Expansion ROM at feac0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: r8169
02:00.0 Mass storage controller [0180]: Silicon Image, Inc. SiI 3132 Serial ATA
Raid II Controller [1095:3132] (rev 01)
Subsystem: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller
[1095:3132]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at febffc00 (64-bit, non-prefetchable) [size=128]
Region 2: Memory at febf8000 (64-bit, non-prefetchable) [size=16K]
Region 4: I/O ports at e880 [size=128]
Expansion ROM at feb00000 [disabled] [size=512K]
Capabilities: <access denied>
Kernel driver in use: sata_sil24
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 148f:3070 Ralink Technology, Corp. RT2870/RT3070
Wireless Adapter
Bus 002 Device 002: ID 058f:9254 Alcor Micro Corp. Hub
Bus 002 Device 003: ID 1e54:2030 TypeMatrix 2030 USB Keyboard
Bus 002 Device 004: ID 045e:0040 Microsoft Corp. Wheel Mouse Optical
-- System Information:
Debian Release: wheezy/sid
APT prefers testing
APT policy: (650, 'testing')
Architecture: i386 (i686)
Kernel: Linux 2.6.39-2-686-pae (SMP w/2 CPU cores)
Locale: LANG=fr_FR.UTF-8, LC_CTYPE=fr_FR.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.1.0-1-686-pae depends on:
ii debconf [debconf-2.0] 1.5.40
ii initramfs-tools [linux-initramfs-tool] 0.99
ii linux-base 3.4
ii module-init-tools 3.16-1
Versions of packages linux-image-3.1.0-1-686-pae recommends:
ii firmware-linux-free 3
ii libc6-i686 2.13-21
Versions of packages linux-image-3.1.0-1-686-pae suggests:
ii grub-pc 1.99-14
ii linux-doc-3.1 3.1.1-1
Versions of packages linux-image-3.1.0-1-686-pae is related to:
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-qlogic <none>
pn firmware-ralink 0.34
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.1.0-1-686-pae/prerm/removing-running-kernel-3.1.0-1-686-pae:
true
linux-image-3.1.0-1-686-pae/postinst/missing-firmware-3.1.0-1-686-pae:
linux-image-3.1.0-1-686-pae/postinst/ignoring-ramdisk:
linux-image-3.1.0-1-686-pae/postinst/depmod-error-initrd-3.1.0-1-686-pae:
false
Motherboard
Model eBox 6620
Chipset Intel Poulsbo XL
CPU / Socket Intel Atom Z510 1,1 GHz
BUS Frequency 533 MHz
Memory
Type DDR2 integrated (1 Go)
Number of slots 0
Max. memory 1 Go
Graphics
Graphics chipset GMA500 HD H/W video decode
Graphics memory 256 Mo shared
Max. resolution 1920 x 1080
VGA 1
DVI None
HDMI None
S-video 1
RCA None
Audio
Type ALC888 HD Audio
Connectors Mic-in / Line-out front
Other connectors
LAN 1 x 10/100/1000 Realtek LAN
COM None
USB 4 x USB 2.0 (2 front)
Parallel None
Firewire None
S/PDIF None
PS/2 1
Storage
IDE None
SATA 1 (for hard-disc 1.8")
Compact Flash Compact Flash card type II for ATA interface
Optical Disk Drive None
Expansion slots
PCI None
Mini-PCI None
PCI 104 None
PCMCIA None
Mini Card None
Express Card None
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.39-2-686-pae (Debian 2.6.39-3) (b...@decadent.org.uk) (gcc version 4.4.6 (Debian 4.4.6-6) ) #1 SMP Tue Jul 5 03:48:49 UTC 2011
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009d800 (usable)
[ 0.000000] BIOS-e820: 000000000009d800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003f680000 (usable)
[ 0.000000] BIOS-e820: 000000003f680000 - 000000003f690000 (reserved)
[ 0.000000] BIOS-e820: 000000003f690000 - 000000003f69e000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003f69e000 - 000000003f6d0000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003f6d0000 - 000000003f6e0000 (reserved)
[ 0.000000] BIOS-e820: 000000003f6e8000 - 000000003f800000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI present.
[ 0.000000] DMI: To Be Filled By O.E.M. To Be Filled By O.E.M./To be filled by O.E.M., BIOS 080015 11/19/2009
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] last_pfn = 0x3f680 max_arch_pfn = 0x1000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-DFFFF uncachable
[ 0.000000] E0000-EFFFF write-through
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask 0C0000000 write-back
[ 0.000000] 1 base 03F700000 mask 0FFF00000 uncachable
[ 0.000000] 2 base 03F800000 mask 0FF800000 uncachable
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] found SMP MP-table at [c00ff780] ff780
[ 0.000000] initial memory mapped : 0 - 01a00000
[ 0.000000] Base memory trampoline at [c0099000] 99000 size 16384
[ 0.000000] init_memory_mapping: 0000000000000000-00000000379fe000
[ 0.000000] 0000000000 - 0000200000 page 4k
[ 0.000000] 0000200000 - 0037800000 page 2M
[ 0.000000] 0037800000 - 00379fe000 page 4k
[ 0.000000] kernel direct mapping tables up to 379fe000 @ 19fa000-1a00000
[ 0.000000] RAMDISK: 36e66000 - 3772b000
[ 0.000000] ACPI: RSDP 000f9080 00024 (v02 ACPIAM)
[ 0.000000] ACPI: XSDT 3f690100 0005C (v01 111909 XSDT1533 20091119 MSFT 00000097)
[ 0.000000] ACPI: FACP 3f690290 000F4 (v04 111909 FACP1533 20091119 MSFT 00000097)
[ 0.000000] ACPI: DSDT 3f690430 03D87 (v02 7652I 7652I102 00000102 INTL 20051117)
[ 0.000000] ACPI: FACS 3f69e000 00040
[ 0.000000] ACPI: APIC 3f690390 0005C (v02 111909 APIC1533 20091119 MSFT 00000097)
[ 0.000000] ACPI: MCFG 3f6903f0 0003C (v01 111909 OEMMCFG 20091119 MSFT 00000097)
[ 0.000000] ACPI: OEMB 3f69e040 0012C (v01 111909 OEMB1533 20091119 MSFT 00000097)
[ 0.000000] ACPI: HPET 3f6941c0 00038 (v01 111909 OEMHPET 20091119 MSFT 00000097)
[ 0.000000] ACPI: GSCI 3f69e170 02024 (v01 111909 GMCHSCI 20091119 MSFT 00000097)
[ 0.000000] ACPI: SSDT 3f6a0470 004F0 (v01 PmRef CpuPm 00003000 INTL 20051117)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 124MB HIGHMEM available.
[ 0.000000] 889MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 379fe000
[ 0.000000] low ram: 0 - 379fe000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x000379fe
[ 0.000000] HighMem 0x000379fe -> 0x0003f680
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009d
[ 0.000000] 0: 0x00000100 -> 0x0003f680
[ 0.000000] On node 0 totalpages: 259597
[ 0.000000] free_area_init_node: node 0, pgdat c14187c0, node_mem_map f6676200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3949 pages, LIFO batch:0
[ 0.000000] Normal zone: 1748 pages used for memmap
[ 0.000000] Normal zone: 221994 pages, LIFO batch:31
[ 0.000000] HighMem zone: 250 pages used for memmap
[ 0.000000] HighMem zone: 31624 pages, LIFO batch:7
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x908
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009d000 - 000000000009e000
[ 0.000000] PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 3f800000 (gap: 3f800000:bf600000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 13 pages/cpu @f6400000 s30976 r0 d22272 u1048576
[ 0.000000] pcpu-alloc: s30976 r0 d22272 u1048576 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 257567
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.39-2-686-pae root=UUID=fea5336a-726d-4e2c-a0cc-61b633ddcbaa ro drm.debug=0x86
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] Initializing HighMem for node 0 (000379fe:0003f680)
[ 0.000000] Memory: 1015040k/1038848k available (2784k kernel code, 23348k reserved, 1435k data, 440k init, 127496k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xffd36000 - 0xfffff000 (2852 kB)
[ 0.000000] pkmap : 0xffa00000 - 0xffc00000 (2048 kB)
[ 0.000000] vmalloc : 0xf81fe000 - 0xff9fe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf79fe000 ( 889 MB)
[ 0.000000] .init : 0xc1420000 - 0xc148e000 ( 440 kB)
[ 0.000000] .data : 0xc12b8340 - 0xc141f240 (1435 kB)
[ 0.000000] .text : 0xc1000000 - 0xc12b8340 (2784 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] NR_IRQS:1280
[ 0.000000] CPU 0 irqstacks, hard=f600a000 soft=f600c000
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration failed
[ 0.000000] TSC: PIT calibration matches HPET. 1 loops
[ 0.000000] Detected 1097.245 MHz processor.
[ 0.004009] Calibrating delay loop (skipped), value calculated using timer frequency.. 2194.49 BogoMIPS (lpj=4388980)
[ 0.004221] pid_max: default: 32768 minimum: 301
[ 0.004494] Security Framework initialized
[ 0.004601] SELinux: Disabled at boot.
[ 0.004768] Mount-cache hash table entries: 512
[ 0.005648] Initializing cgroup subsys ns
[ 0.005753] ns_cgroup deprecated: consider using the 'clone_children' flag without the ns_cgroup.
[ 0.005897] Initializing cgroup subsys cpuacct
[ 0.006065] Initializing cgroup subsys memory
[ 0.006201] Initializing cgroup subsys devices
[ 0.006303] Initializing cgroup subsys freezer
[ 0.006407] Initializing cgroup subsys net_cls
[ 0.006509] Initializing cgroup subsys blkio
[ 0.006687] CPU: Physical Processor ID: 0
[ 0.006788] CPU: Processor Core ID: 0
[ 0.006888] mce: CPU supports 5 MCE banks
[ 0.007012] CPU0: Thermal monitoring enabled (TM1)
[ 0.007116] using mwait in idle threads.
[ 0.010197] ACPI: Core revision 20110316
[ 0.020192] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.020705] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.062989] CPU0: Intel(R) Atom(TM) CPU Z510 @ 1.10GHz stepping 02
[ 0.064003] Performance Events: PEBS fmt0+, Atom events, Intel PMU driver.
[ 0.064003] ... version: 3
[ 0.064003] ... bit width: 40
[ 0.064003] ... generic registers: 2
[ 0.064003] ... value mask: 000000ffffffffff
[ 0.064003] ... max period: 000000007fffffff
[ 0.064003] ... fixed-purpose events: 3
[ 0.064003] ... event mask: 0000000700000003
[ 0.064003] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.064003] CPU 1 irqstacks, hard=f60b6000 soft=f60b8000
[ 0.064003] Booting Node 0, Processors #1 Ok.
[ 0.064003] smpboot cpu 1: start_ip = 99000
[ 0.008000] Initializing CPU#1
[ 0.156092] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.156407] Brought up 2 CPUs
[ 0.156511] Total of 2 processors activated (4389.00 BogoMIPS).
[ 0.157324] devtmpfs: initialized
[ 0.157324] PM: Registering ACPI NVS region at 3f69e000 (204800 bytes)
[ 0.157324] print_constraints: dummy:
[ 0.157324] NET: Registered protocol family 16
[ 0.160067] ACPI: bus type pci registered
[ 0.160563] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.160709] PCI: not using MMCONFIG
[ 0.161103] PCI : PCI BIOS aera is rw and x. Use pci=nobios if you want it NX.
[ 0.161326] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=2
[ 0.161433] PCI: Using configuration type 1 for base access
[ 0.162815] bio: create slab <bio-0> at 0
[ 0.166075] ACPI: EC: Look up EC in DSDT
[ 0.168576] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.173063] ACPI Warning: Incorrect checksum in table [OEMB] - 0x47, should be 0x98 (20110316/tbutils-314)
[ 0.174218] ACPI: SSDT 3f6a0270 001FA (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
[ 0.175048] ACPI: Dynamic OEM Table Load:
[ 0.175265] ACPI: SSDT (null) 001FA (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
[ 0.176341] ACPI: SSDT 3f6a01a0 000CC (v01 PmRef Cpu1Ist 00003000 INTL 20051117)
[ 0.177145] ACPI: Dynamic OEM Table Load:
[ 0.177360] ACPI: SSDT (null) 000CC (v01 PmRef Cpu1Ist 00003000 INTL 20051117)
[ 0.178060] ACPI: Interpreter enabled
[ 0.178170] ACPI: (supports S0 S3 S4 S5)
[ 0.178547] ACPI: Using IOAPIC for interrupt routing
[ 0.178729] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.182425] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
[ 0.182567] PCI: Using MMCONFIG for extended config space
[ 0.183839] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
[ 0.204308] ACPI: No dock devices found.
[ 0.204414] HEST: Table not found.
[ 0.204518] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.204978] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.205727] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
[ 0.205845] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
[ 0.205956] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[ 0.206092] pci_root PNP0A08:00: host bridge window [mem 0x000d0000-0x000dffff]
[ 0.206229] pci_root PNP0A08:00: host bridge window [mem 0x3f800000-0xdfffffff]
[ 0.206366] pci_root PNP0A08:00: host bridge window [mem 0xf0000000-0xffffffff]
[ 0.206515] pci_root PNP0A08:00: address space collision: host bridge window [mem 0x000d0000-0x000dffff] conflicts with Adapter ROM [mem 0x000ce800-0x000d27ff]
[ 0.206729] pci 0000:00:00.0: [8086:8100] type 0 class 0x000600
[ 0.206844] pci 0000:00:02.0: [8086:8108] type 0 class 0x000300
[ 0.206880] pci 0000:00:02.0: reg 10: [mem 0xfe980000-0xfe9fffff]
[ 0.206900] pci 0000:00:02.0: reg 14: [io 0xc880-0xc887]
[ 0.206919] pci 0000:00:02.0: reg 18: [mem 0xd0000000-0xdfffffff]
[ 0.206939] pci 0000:00:02.0: reg 1c: [mem 0xfe940000-0xfe97ffff]
[ 0.207087] pci 0000:00:1b.0: [8086:811b] type 0 class 0x000403
[ 0.207119] pci 0000:00:1b.0: reg 10: [mem 0xfe938000-0xfe93bfff 64bit]
[ 0.207207] pci 0000:00:1b.0: PME# supported from D0 D3hot
[ 0.207219] pci 0000:00:1b.0: PME# disabled
[ 0.207259] pci 0000:00:1c.0: [8086:8110] type 1 class 0x000604
[ 0.207345] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.207356] pci 0000:00:1c.0: PME# disabled
[ 0.207398] pci 0000:00:1c.1: [8086:8112] type 1 class 0x000604
[ 0.207484] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.207495] pci 0000:00:1c.1: PME# disabled
[ 0.207541] pci 0000:00:1d.0: [8086:8114] type 0 class 0x000c03
[ 0.207602] pci 0000:00:1d.0: reg 20: [io 0xc480-0xc49f]
[ 0.207659] pci 0000:00:1d.1: [8086:8115] type 0 class 0x000c03
[ 0.207722] pci 0000:00:1d.1: reg 20: [io 0xc080-0xc09f]
[ 0.207777] pci 0000:00:1d.2: [8086:8116] type 0 class 0x000c03
[ 0.207840] pci 0000:00:1d.2: reg 20: [io 0xb880-0xb89f]
[ 0.207935] pci 0000:00:1d.7: [8086:8117] type 0 class 0x000c03
[ 0.207978] pci 0000:00:1d.7: reg 10: [mem 0xfe937c00-0xfe937fff]
[ 0.208132] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.208146] pci 0000:00:1d.7: PME# disabled
[ 0.208185] pci 0000:00:1f.0: [8086:8119] type 0 class 0x000601
[ 0.208300] pci 0000:00:1f.1: [8086:811a] type 0 class 0x000101
[ 0.208365] pci 0000:00:1f.1: reg 20: [io 0xffa0-0xffaf]
[ 0.208503] pci 0000:01:00.0: [10ec:8168] type 0 class 0x000200
[ 0.208535] pci 0000:01:00.0: reg 10: [io 0xdd00-0xddff]
[ 0.208582] pci 0000:01:00.0: reg 18: [mem 0xfeaff000-0xfeafffff 64bit]
[ 0.208616] pci 0000:01:00.0: reg 20: [mem 0xcfff0000-0xcfffffff 64bit pref]
[ 0.208640] pci 0000:01:00.0: reg 30: [mem 0xfeac0000-0xfeadffff pref]
[ 0.208702] pci 0000:01:00.0: supports D1 D2
[ 0.208710] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.208722] pci 0000:01:00.0: PME# disabled
[ 0.216053] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
[ 0.216163] pci 0000:00:1c.0: bridge window [io 0xd000-0xdfff]
[ 0.216175] pci 0000:00:1c.0: bridge window [mem 0xfea00000-0xfeafffff]
[ 0.216188] pci 0000:00:1c.0: bridge window [mem 0xcff00000-0xcfffffff pref]
[ 0.216293] pci 0000:02:00.0: [1095:3132] type 0 class 0x000180
[ 0.216338] pci 0000:02:00.0: reg 10: [mem 0xfebffc00-0xfebffc7f 64bit]
[ 0.216374] pci 0000:02:00.0: reg 18: [mem 0xfebf8000-0xfebfbfff 64bit]
[ 0.216400] pci 0000:02:00.0: reg 20: [io 0xe880-0xe8ff]
[ 0.216442] pci 0000:02:00.0: reg 30: [mem 0xfeb00000-0xfeb7ffff pref]
[ 0.216504] pci 0000:02:00.0: supports D1 D2
[ 0.216538] pci 0000:02:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.220037] pci 0000:00:1c.1: PCI bridge to [bus 02-02]
[ 0.220146] pci 0000:00:1c.1: bridge window [io 0xe000-0xefff]
[ 0.220158] pci 0000:00:1c.1: bridge window [mem 0xfeb00000-0xfebfffff]
[ 0.220171] pci 0000:00:1c.1: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.220196] pci_bus 0000:00: on NUMA node 0
[ 0.220209] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.220558] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.POP4._PRT]
[ 0.220682] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.POP5._PRT]
[ 0.220792] pci0000:00: Requesting ACPI _OSC control (0x1d)
[ 0.220900] Unable to assume _OSC PCIe control. Disabling ASPM
[ 0.233641] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 0.234591] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 0.235533] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.236488] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 *15)
[ 0.237430] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.238512] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.239596] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.240687] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.241973] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.242128] vgaarb: loaded
[ 0.242360] PCI: Using ACPI for IRQ routing
[ 0.242466] PCI: pci_cache_line_size set to 64 bytes
[ 0.242584] reserve RAM buffer: 000000000009d800 - 000000000009ffff
[ 0.242594] reserve RAM buffer: 000000003f680000 - 000000003fffffff
[ 0.243005] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.243125] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.243458] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.248082] Switching to clocksource hpet
[ 0.251709] Switched to NOHz mode on CPU #0
[ 0.251813] Switched to NOHz mode on CPU #1
[ 0.252170] pnp: PnP ACPI init
[ 0.252320] ACPI: bus type pnp registered
[ 0.252820] pnp 00:00: [bus 00-ff]
[ 0.252831] pnp 00:00: [io 0x0cf8-0x0cff]
[ 0.252840] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 0.252849] pnp 00:00: [io 0x0d00-0xffff window]
[ 0.252859] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 0.252868] pnp 00:00: [mem 0x000d0000-0x000dffff window]
[ 0.252877] pnp 00:00: [mem 0x3f800000-0xdfffffff window]
[ 0.252887] pnp 00:00: [mem 0xf0000000-0xffffffff window]
[ 0.253042] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 0.253325] pnp 00:01: [mem 0x40000000-0x7fffffff]
[ 0.253336] pnp 00:01: [mem 0x3f800000-0x3fffffff]
[ 0.253479] system 00:01: [mem 0x40000000-0x7fffffff] has been reserved
[ 0.253597] system 00:01: [mem 0x3f800000-0x3fffffff] has been reserved
[ 0.253710] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.253808] pnp 00:02: [io 0x0070-0x0071]
[ 0.253838] pnp 00:02: [irq 8]
[ 0.253932] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.254098] pnp 00:03: [io 0x0061]
[ 0.254200] pnp 00:03: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.254238] pnp 00:04: [io 0x00f0-0x00ff]
[ 0.254255] pnp 00:04: [irq 13]
[ 0.254349] pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.254666] pnp 00:05: [io 0x0000-0xffffffffffffffff disabled]
[ 0.254677] pnp 00:05: [io 0x0a00-0x0a0f]
[ 0.254686] pnp 00:05: [io 0x0a10-0x0a1f]
[ 0.254838] system 00:05: [io 0x0a00-0x0a0f] has been reserved
[ 0.254950] system 00:05: [io 0x0a10-0x0a1f] has been reserved
[ 0.255060] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.255449] pnp 00:06: [io 0x0010-0x001f]
[ 0.255459] pnp 00:06: [io 0x0022-0x003f]
[ 0.255467] pnp 00:06: [io 0x0044-0x005f]
[ 0.255475] pnp 00:06: [io 0x0063]
[ 0.255482] pnp 00:06: [io 0x0065]
[ 0.255490] pnp 00:06: [io 0x0067-0x006f]
[ 0.255498] pnp 00:06: [io 0x0072-0x007f]
[ 0.255506] pnp 00:06: [io 0x0080]
[ 0.255513] pnp 00:06: [io 0x0084-0x0086]
[ 0.255521] pnp 00:06: [io 0x0088]
[ 0.255529] pnp 00:06: [io 0x008c-0x008e]
[ 0.255537] pnp 00:06: [io 0x0090-0x009f]
[ 0.255545] pnp 00:06: [io 0x00a2-0x00bf]
[ 0.255552] pnp 00:06: [io 0x00e0-0x00ef]
[ 0.255560] pnp 00:06: [io 0x04d0-0x04d1]
[ 0.255568] pnp 00:06: [io 0x0900-0x09f3]
[ 0.255576] pnp 00:06: [io 0x0400-0x043f]
[ 0.255584] pnp 00:06: [io 0x0480-0x04bf]
[ 0.255593] pnp 00:06: [mem 0xf0000000-0xf0003fff]
[ 0.255777] system 00:06: [io 0x04d0-0x04d1] has been reserved
[ 0.255901] system 00:06: [io 0x0900-0x09f3] has been reserved
[ 0.256059] system 00:06: [io 0x0400-0x043f] has been reserved
[ 0.256169] system 00:06: [io 0x0480-0x04bf] has been reserved
[ 0.256279] system 00:06: [mem 0xf0000000-0xf0003fff] has been reserved
[ 0.256392] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.256476] pnp 00:07: [mem 0xfed00000-0xfed003ff]
[ 0.256581] pnp 00:07: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.256760] pnp 00:08: [mem 0xff800000-0xffbfffff]
[ 0.256771] pnp 00:08: [mem 0xffc00000-0xffffffff]
[ 0.256867] pnp 00:08: Plug and Play ACPI device, IDs INT0800 (active)
[ 0.257028] pnp 00:09: [mem 0xffc00000-0xffbfffff disabled]
[ 0.257163] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.257477] pnp 00:0a: [io 0x0060]
[ 0.257486] pnp 00:0a: [io 0x0064]
[ 0.257495] pnp 00:0a: [mem 0xfec00000-0xfec00fff]
[ 0.257504] pnp 00:0a: [mem 0xfee00000-0xfee00fff]
[ 0.257645] system 00:0a: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.257760] system 00:0a: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.257874] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.258009] pnp 00:0b: [mem 0xe0000000-0xefffffff]
[ 0.258150] system 00:0b: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.258264] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.258756] pnp 00:0c: [mem 0x00000000-0x0009ffff]
[ 0.258767] pnp 00:0c: [mem 0x000c0000-0x000cffff]
[ 0.258776] pnp 00:0c: [mem 0x000e0000-0x000fffff]
[ 0.258785] pnp 00:0c: [mem 0x00100000-0x3f7fffff]
[ 0.258795] pnp 00:0c: [mem 0x00000000-0xffffffffffffffff disabled]
[ 0.258926] system 00:0c: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.259041] system 00:0c: [mem 0x000c0000-0x000cffff] could not be reserved
[ 0.259155] system 00:0c: [mem 0x000e0000-0x000fffff] could not be reserved
[ 0.259268] system 00:0c: [mem 0x00100000-0x3f7fffff] could not be reserved
[ 0.259382] system 00:0c: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.259834] pnp: PnP ACPI: found 13 devices
[ 0.259935] ACPI: ACPI bus type pnp unregistered
[ 0.260068] PnPBIOS: Disabled by ACPI PNP
[ 0.301277] pci 0000:00:1c.1: BAR 15: assigned [mem 0x80000000-0x801fffff pref]
[ 0.301424] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
[ 0.301533] pci 0000:00:1c.0: bridge window [io 0xd000-0xdfff]
[ 0.301646] pci 0000:00:1c.0: bridge window [mem 0xfea00000-0xfeafffff]
[ 0.301760] pci 0000:00:1c.0: bridge window [mem 0xcff00000-0xcfffffff pref]
[ 0.301903] pci 0000:00:1c.1: PCI bridge to [bus 02-02]
[ 0.302009] pci 0000:00:1c.1: bridge window [io 0xe000-0xefff]
[ 0.302121] pci 0000:00:1c.1: bridge window [mem 0xfeb00000-0xfebfffff]
[ 0.302235] pci 0000:00:1c.1: bridge window [mem 0x80000000-0x801fffff pref]
[ 0.302412] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.302528] pci 0000:00:1c.0: setting latency timer to 64
[ 0.302551] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.302665] pci 0000:00:1c.1: setting latency timer to 64
[ 0.302677] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.302687] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.302696] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.302706] pci_bus 0000:00: resource 7 [mem 0x3f800000-0xdfffffff]
[ 0.302715] pci_bus 0000:00: resource 8 [mem 0xf0000000-0xffffffff]
[ 0.302725] pci_bus 0000:01: resource 0 [io 0xd000-0xdfff]
[ 0.302735] pci_bus 0000:01: resource 1 [mem 0xfea00000-0xfeafffff]
[ 0.302745] pci_bus 0000:01: resource 2 [mem 0xcff00000-0xcfffffff pref]
[ 0.302755] pci_bus 0000:02: resource 0 [io 0xe000-0xefff]
[ 0.302764] pci_bus 0000:02: resource 1 [mem 0xfeb00000-0xfebfffff]
[ 0.302774] pci_bus 0000:02: resource 2 [mem 0x80000000-0x801fffff pref]
[ 0.302989] NET: Registered protocol family 2
[ 0.303391] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.304559] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.306207] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.307120] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.307232] TCP reno registered
[ 0.307338] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.307474] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.308382] NET: Registered protocol family 1
[ 0.308547] pci 0000:00:02.0: Boot video device
[ 0.308716] PCI: CLS 32 bytes, default 64
[ 0.308875] Unpacking initramfs...
[ 1.040537] Freeing initrd memory: 8980k freed
[ 1.057150] audit: initializing netlink socket (disabled)
[ 1.057293] type=2000 audit(1322186130.052:1): initialized
[ 1.094730] highmem bounce pool size: 64 pages
[ 1.094849] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.095951] VFS: Disk quotas dquot_6.5.2
[ 1.096340] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.096792] msgmni has been set to 1751
[ 1.097477] alg: No test for stdrng (krng)
[ 1.097696] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.097837] io scheduler noop registered
[ 1.097935] io scheduler deadline registered
[ 1.098087] io scheduler cfq registered (default)
[ 1.098926] ERST: Table is not found!
[ 1.099062] isapnp: Scanning for PnP cards...
[ 1.454299] isapnp: No Plug & Play device found
[ 1.454625] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.475399] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.496274] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.497862] Linux agpgart interface v0.103
[ 1.498660] i8042: PNP: No PS/2 controller found. Probing ports directly.
[ 1.501611] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.501732] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.502269] mousedev: PS/2 mouse device common for all mice
[ 1.502517] rtc_cmos 00:02: RTC can wake from S4
[ 1.502874] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 1.503018] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 1.503167] cpuidle: using governor ladder
[ 1.503267] cpuidle: using governor menu
[ 1.504287] TCP cubic registered
[ 1.504554] NET: Registered protocol family 10
[ 1.506904] Mobile IPv6
[ 1.507004] NET: Registered protocol family 17
[ 1.507114] Registering the dns_resolver key type
[ 1.507282] Using IPI No-Shortcut mode
[ 1.507707] PM: Hibernation image not present or could not be loaded.
[ 1.507748] registered taskstats version 1
[ 1.508636] rtc_cmos 00:02: setting system clock to 2011-11-25 01:55:30 UTC (1322186130)
[ 1.508884] Initializing network drop monitor service
[ 1.509283] Freeing unused kernel memory: 440k freed
[ 1.509865] Write protecting the kernel text: 2788k
[ 1.510052] Write protecting the kernel read-only data: 1032k
[ 1.510157] NX-protecting the kernel data: 3356k
[ 1.554126] udevd[47]: starting version 171
[ 1.843820] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 1.856501] r8169 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.856714] r8169 0000:01:00.0: setting latency timer to 64
[ 1.856817] r8169 0000:01:00.0: irq 40 for MSI/MSI-X
[ 1.859385] r8169 0000:01:00.0: eth0: RTL8168c/8111c at 0xf8314000, 00:50:c2:20:2d:f1, XID 1c4000c0 IRQ 40
[ 2.051761] SCSI subsystem initialized
[ 2.056246] Refined TSC clocksource calibration: 1097.249 MHz.
[ 2.056375] Switching to clocksource tsc
[ 2.064706] usbcore: registered new interface driver usbfs
[ 2.064908] usbcore: registered new interface driver hub
[ 2.075062] usbcore: registered new device driver usb
[ 2.096443] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.096679] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 2.104185] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 2.104203] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 2.104481] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 2.128161] ehci_hcd 0000:00:1d.7: debug port 1
[ 2.132183] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 2.132255] ehci_hcd 0000:00:1d.7: irq 19, io mem 0xfe937c00
[ 2.148062] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 2.148314] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.148434] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.148574] usb usb1: Product: EHCI Host Controller
[ 2.148682] usb usb1: Manufacturer: Linux 2.6.39-2-686-pae ehci_hcd
[ 2.148794] usb usb1: SerialNumber: 0000:00:1d.7
[ 2.149503] hub 1-0:1.0: USB hub found
[ 2.149644] hub 1-0:1.0: 8 ports detected
[ 2.171072] uhci_hcd: USB Universal Host Controller Interface driver
[ 2.171351] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.171499] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 2.171515] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 2.171689] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 2.188241] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000c480
[ 2.188532] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.188650] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.188792] usb usb2: Product: UHCI Host Controller
[ 2.188899] usb usb2: Manufacturer: Linux 2.6.39-2-686-pae uhci_hcd
[ 2.189011] usb usb2: SerialNumber: 0000:00:1d.0
[ 2.189710] hub 2-0:1.0: USB hub found
[ 2.189831] hub 2-0:1.0: 2 ports detected
[ 2.190218] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 2.190354] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 2.190368] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 2.190503] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 2.261853] libata version 3.00 loaded.
[ 2.268184] uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000c080
[ 2.268465] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.268580] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.268716] usb usb3: Product: UHCI Host Controller
[ 2.268818] usb usb3: Manufacturer: Linux 2.6.39-2-686-pae uhci_hcd
[ 2.268926] usb usb3: SerialNumber: 0000:00:1d.1
[ 2.269443] hub 3-0:1.0: USB hub found
[ 2.269553] hub 3-0:1.0: 2 ports detected
[ 2.269915] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 2.270043] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 2.270053] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 2.270178] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 2.288197] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000b880
[ 2.288481] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.288600] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.288741] usb usb4: Product: UHCI Host Controller
[ 2.294304] usb usb4: Manufacturer: Linux 2.6.39-2-686-pae uhci_hcd
[ 2.294418] usb usb4: SerialNumber: 0000:00:1d.2
[ 2.295116] hub 4-0:1.0: USB hub found
[ 2.295244] hub 4-0:1.0: 2 ports detected
[ 2.295649] pata_sch 0000:00:1f.1: version 0.2
[ 2.295854] pata_sch 0000:00:1f.1: setting latency timer to 64
[ 2.297832] scsi0 : pata_sch
[ 2.298967] scsi1 : pata_sch
[ 2.300404] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[ 2.300533] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[ 2.306553] sata_sil24 0000:02:00.0: version 1.1
[ 2.306597] sata_sil24 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 2.307405] sata_sil24 0000:02:00.0: setting latency timer to 64
[ 2.309219] scsi2 : sata_sil24
[ 2.309730] scsi3 : sata_sil24
[ 2.310107] ata3: SATA max UDMA/100 host m128@0xfebffc00 port 0xfebf8000 irq 17
[ 2.310261] ata4: SATA max UDMA/100 host m128@0xfebffc00 port 0xfebfa000 irq 17
[ 2.580045] usb 1-4: new high speed USB device number 3 using ehci_hcd
[ 2.729439] usb 1-4: New USB device found, idVendor=148f, idProduct=3070
[ 2.729559] usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.729675] usb 1-4: Product: 802.11 n WLAN
[ 2.729778] usb 1-4: Manufacturer: Ralink
[ 2.729880] usb 1-4: SerialNumber: 1.0
[ 2.972043] usb 2-2: new full speed USB device number 2 using uhci_hcd
[ 3.141494] usb 2-2: New USB device found, idVendor=058f, idProduct=9254
[ 3.141611] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.141723] usb 2-2: Product: Generic USB Hub
[ 3.141823] usb 2-2: Manufacturer: ALCOR
[ 3.144775] hub 2-2:1.0: USB hub found
[ 3.146528] hub 2-2:1.0: 4 ports detected
[ 3.429501] usb 2-2.1: new low speed USB device number 3 using uhci_hcd
[ 3.637496] usb 2-2.1: New USB device found, idVendor=1e54, idProduct=2030
[ 3.637612] usb 2-2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.637748] usb 2-2.1: Product: USB Keyboard
[ 3.637848] usb 2-2.1: Manufacturer: TypeMatrix.com
[ 3.717517] usb 2-2.3: new low speed USB device number 4 using uhci_hcd
[ 3.763342] input: TypeMatrix.com USB Keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2.1/2-2.1:1.0/input/input0
[ 3.763764] generic-usb 0003:1E54:2030.0001: input,hidraw0: USB HID v1.10 Keyboard [TypeMatrix.com USB Keyboard] on usb-0000:00:1d.0-2.1/input0
[ 3.835332] input: TypeMatrix.com USB Keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2.1/2-2.1:1.1/input/input1
[ 3.836594] generic-usb 0003:1E54:2030.0002: input,hiddev0,hidraw1: USB HID v1.10 Device [TypeMatrix.com USB Keyboard] on usb-0000:00:1d.0-2.1/input1
[ 3.836853] usbcore: registered new interface driver usbhid
[ 3.836966] usbhid: USB HID core driver
[ 3.860500] usb 2-2.3: New USB device found, idVendor=045e, idProduct=0040
[ 3.860620] usb 2-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.860756] usb 2-2.3: Product: Microsoft Wheel Mouse Optical®
[ 3.860862] usb 2-2.3: Manufacturer: Microsoft
[ 3.879317] input: Microsoft Microsoft Wheel Mouse Optical® as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2.3/2-2.3:1.0/input/input2
[ 3.879884] generic-usb 0003:045E:0040.0003: input,hidraw2: USB HID v1.00 Mouse [Microsoft Microsoft Wheel Mouse Optical®] on usb-0000:00:1d.0-2.3/input0
[ 4.508064] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 4.555921] ata3.00: ATA-8: TOSHIBA MK1235GSL, PV010J, max UDMA/100
[ 4.556057] ata3.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 4.556960] ata3.00: configured for UDMA/100
[ 4.557488] scsi 2:0:0:0: Direct-Access ATA TOSHIBA MK1235GS PV01 PQ: 0 ANSI: 5
[ 6.636058] ata4: SATA link down (SStatus 0 SControl 0)
[ 6.690776] sd 2:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/111 GiB)
[ 6.691264] sd 2:0:0:0: [sda] Write Protect is off
[ 6.691384] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 6.691532] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 6.753249] sda: sda1 sda2 < sda5 >
[ 6.754619] sd 2:0:0:0: [sda] Attached SCSI disk
[ 7.355257] PM: Starting manual resume from disk
[ 7.355396] PM: Hibernation image partition 8:5 present
[ 7.355403] PM: Looking for hibernation image.
[ 7.355718] PM: Image not found (code -22)
[ 7.355724] PM: Hibernation image not present or could not be loaded.
[ 7.419210] EXT3-fs: barriers not enabled
[ 7.436242] kjournald starting. Commit interval 5 seconds
[ 7.436516] EXT3-fs (sda1): mounted filesystem with ordered data mode
[ 10.069349] udevd[228]: starting version 172
[ 11.121071] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input3
[ 11.121236] ACPI: Sleep Button [SLPB]
[ 11.121636] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4
[ 11.121787] ACPI: Power Button [PWRB]
[ 11.122197] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input5
[ 11.122426] ACPI: Lid Switch [LID]
[ 11.195138] ACPI: acpi_idle registered with cpuidle
[ 12.563478] input: PC Speaker as /devices/platform/pcspkr/input/input6
[ 12.954703] cfg80211: Calling CRDA to update world regulatory domain
[ 12.970278] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 12.970530] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 13.305284] hda_codec: ALC888: BIOS auto-probing.
[ 13.305420] hda_codec: ALC888: SKU not ready 0x00000100
[ 13.307523] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input7
[ 13.313941] input: HDA Intel MID Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card1/input8
[ 13.915992] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 13.918454] Registered led device: rt2800usb-phy0::radio
[ 13.918571] Registered led device: rt2800usb-phy0::assoc
[ 13.918687] Registered led device: rt2800usb-phy0::quality
[ 13.919042] usbcore: registered new interface driver rt2800usb
[ 16.132894] Adding 2650688k swap on /dev/sda5. Priority:-1 extents:1 across:2650688k
[ 16.566896] EXT3-fs (sda1): using internal journal
[ 16.771566] loop: module loaded
[ 20.102223] r8169 0000:01:00.0: eth0: link down
[ 20.102346] r8169 0000:01:00.0: eth0: link down
[ 20.103079] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 20.999518] fuse init (API version 7.16)
[ 21.873348] r8169 0000:01:00.0: eth0: link up
[ 21.873974] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 23.772278] lp: driver loaded but no devices found
[ 24.022975] ppdev: user-space parallel port driver
[ 24.067478] parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
[ 24.067952] parport0: irq 7 detected
[ 24.164555] lp0: using parport0 (polling).
[ 32.064028] eth0: no IPv6 routers present
