Package: linux-2.6 Version: 2.6.32-38 Severity: normal Hi all,
after upgrading my Sheeva plug from Debian 6.0.2 to 6.0.3 also the kernel version 2.6.32-38 was installed. Since then my two Western Digital USB harddisk are no longer recognised. The kernel is reporting: [ 232.030408] scsi_mod: Unknown symbol blk_get_queue [ 232.041504] scsi_mod: Unknown symbol blk_put_queue "lsusb" is showing the disks, the block devices are missing though : sheeva:~# lsusb Bus 001 Device 005: ID 1058:1100 Western Digital Technologies, Inc. Bus 001 Device 003: ID 1058:1100 Western Digital Technologies, Inc. Bus 001 Device 002: ID 0409:005a NEC Corp. HighSpeed Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub sheeva:~# ls -l /dev/disk/by-uuid total 0 lrwxrwxrwx 1 root root 15 Oct 9 19:04 01a4a7e9-2da7-4055-bf04-41ff3a00d692 -> ../../mmcblk0p1 lrwxrwxrwx 1 root root 15 Oct 9 19:04 87413beb-de04-4716-a6de-be2b1bef095a -> ../../mmcblk0p2 lrwxrwxrwx 1 root root 15 Oct 9 19:04 d164bff8-cdda-4d73-b1d9-68bc20f7f21f -> ../../mmcblk0p3 sheeva:~# Kind regards, Joerg. -- Package-specific info: ** Version: Linux version 2.6.32-5-kirkwood (Debian 2.6.32-30) (b...@decadent.org.uk) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 Wed Jan 12 15:27:07 UTC 2011 ** Command line: console=ttyS0,115200 root=/dev/mmcblk0p2 ** Not tainted ** Kernel log: [ 23.415626] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 23.422983] orion-ehci orion-ehci.0: Marvell Orion EHCI [ 23.428286] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1 [ 23.461328] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000 [ 23.479320] mmc0: host does not support reading read-only switch. assuming write-enable. [ 23.487758] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00 [ 23.495441] mmc0: new high speed SDHC card at address f5bb [ 23.502005] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 23.508829] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 23.516116] usb usb1: Product: Marvell Orion EHCI [ 23.520851] usb usb1: Manufacturer: Linux 2.6.32-5-kirkwood ehci_hcd [ 23.527247] usb usb1: SerialNumber: orion-ehci.0 [ 23.544861] mmcblk0: mmc0:f5bb SD08G 7.42 GiB [ 23.549486] mmcblk0: [ 23.552295] usb usb1: configuration #1 chosen from 1 choice [ 23.558184] p1 p2 p3 [ 23.560882] hub 1-0:1.0: USB hub found [ 23.567980] hub 1-0:1.0: 1 port detected [ 23.888371] md: linear personality registered for level -1 [ 23.893964] usb 1-1: new high speed USB device using orion-ehci and address 2 [ 23.913120] md: multipath personality registered for level -4 [ 23.929054] md: raid0 personality registered for level 0 [ 23.951804] md: raid1 personality registered for level 1 [ 23.965997] async_tx: api initialized (async) [ 23.974738] xor: measuring software checksum speed [ 24.021303] arm4regs : 1084.800 MB/sec [ 24.071302] 8regs : 804.000 MB/sec [ 24.121304] 32regs : 900.400 MB/sec [ 24.125505] xor: using function: arm4regs (1084.800 MB/sec) [ 24.301404] raid6: int32x1 79 MB/s [ 24.471842] raid6: int32x2 104 MB/s [ 24.641601] raid6: int32x4 124 MB/s [ 24.811649] raid6: int32x8 110 MB/s [ 24.815414] raid6: using algorithm int32x4 (124 MB/s) [ 24.831741] usb 1-1: New USB device found, idVendor=0409, idProduct=005a [ 24.838480] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 24.862634] usb 1-1: configuration #1 chosen from 1 choice [ 24.872882] md: raid6 personality registered for level 6 [ 24.878225] md: raid5 personality registered for level 5 [ 24.883609] md: raid4 personality registered for level 4 [ 24.889877] hub 1-1:1.0: USB hub found [ 24.899369] hub 1-1:1.0: 4 ports detected [ 24.933616] md: raid10 personality registered for level 10 [ 24.972508] uncorrectable error : [ 24.975757] uncorrectable error : [ 24.979187] end_request: I/O error, dev mtdblock0, sector 0 [ 25.020618] kjournald starting. Commit interval 5 seconds [ 25.026240] EXT3-fs: mounted filesystem with ordered data mode. [ 25.181526] usb 1-1.1: new high speed USB device using orion-ehci and address 3 [ 25.312727] usb 1-1.1: New USB device found, idVendor=1058, idProduct=1100 [ 25.319650] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 25.327016] usb 1-1.1: Product: My Book [ 25.331695] usb 1-1.1: Manufacturer: Western Digital [ 25.336767] usb 1-1.1: SerialNumber: 57442D574D41535530343632393230 [ 25.343501] usb 1-1.1: configuration #1 chosen from 1 choice [ 25.441532] usb 1-1.2: new high speed USB device using orion-ehci and address 4 [ 25.572988] usb 1-1.2: New USB device found, idVendor=1058, idProduct=1100 [ 25.579901] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 25.587280] usb 1-1.2: Product: My Book [ 25.591954] usb 1-1.2: Manufacturer: Western Digital [ 25.597033] usb 1-1.2: SerialNumber: 57442D574341535534363033363633 [ 25.613406] usb 1-1.2: configuration #1 chosen from 1 choice [ 25.719119] udev[162]: starting version 164 [ 26.203838] scsi_mod: Unknown symbol blk_get_queue [ 26.214881] scsi_mod: Unknown symbol blk_put_queue [ 26.255463] scsi_mod: Unknown symbol blk_get_queue [ 26.266517] scsi_mod: Unknown symbol blk_put_queue [ 26.432287] uncorrectable error : [ 26.435529] uncorrectable error : [ 26.438952] end_request: I/O error, dev mtdblock0, sector 0 [ 26.907509] Adding 503308k swap on /dev/mmcblk0p3. Priority:-1 extents:1 across:503308k SS [ 27.234118] EXT3 FS on mmcblk0p2, internal journal [ 27.448855] loop: module loaded [ 28.400776] RPC: Registered udp transport module. [ 28.405717] RPC: Registered tcp transport module. [ 28.410444] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 28.527829] Slow work thread pool: Starting up [ 28.536913] Slow work thread pool: Ready [ 28.543671] FS-Cache: Loaded [ 28.691853] FS-Cache: Netfs 'nfs' registered for caching [ 28.815331] Installing knfsd (copyright (C) 1996 o...@monad.swb.de). [ 29.006794] NET: Registered protocol family 10 [ 29.020893] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 29.962625] eth0: link up, 100 Mb/s, full duplex, flow control disabled [ 29.969448] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 30.832203] svc: failed to register lockdv1 RPC service (errno 97). [ 30.849493] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory [ 30.869852] NFSD: starting 90-second grace period [ 40.741304] eth0: no IPv6 routers present [ 173.408713] udev[1160]: starting version 164 [ 217.518857] usb 1-1.2: USB disconnect, address 4 [ 231.836015] usb 1-1.2: new high speed USB device using orion-ehci and address 5 [ 231.967230] usb 1-1.2: New USB device found, idVendor=1058, idProduct=1100 [ 231.974140] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 231.981501] usb 1-1.2: Product: My Book [ 231.986175] usb 1-1.2: Manufacturer: Western Digital [ 231.991248] usb 1-1.2: SerialNumber: 57442D574341535534363033363633 [ 232.000358] usb 1-1.2: configuration #1 chosen from 1 choice [ 232.030408] scsi_mod: Unknown symbol blk_get_queue [ 232.041504] scsi_mod: Unknown symbol blk_put_queue ** Model information Processor : Feroceon 88FR131 rev 1 (v5l) Hardware : Marvell SheevaPlug Reference Board Revision : 0000 ** Loaded modules: Module Size Used by ipv6 253786 22 nfsd 247560 13 exportfs 3000 1 nfsd nfs 270508 0 lockd 63165 2 nfsd,nfs fscache 34105 1 nfs nfs_acl 2277 2 nfsd,nfs auth_rpcgss 33334 2 nfsd,nfs sunrpc 171216 12 nfsd,nfs,lockd,nfs_acl,auth_rpcgss loop 11427 0 gpio_keys 3066 0 hmac 2475 0 sha1_generic 1717 0 mv_cesa 9262 0 aes_generic 32820 1 mv_cesa raid10 19535 0 raid456 50943 0 async_raid6_recov 4240 1 raid456 async_pq 3424 2 raid456,async_raid6_recov raid6_pq 75781 2 async_raid6_recov,async_pq async_xor 2563 3 raid456,async_raid6_recov,async_pq xor 4819 1 async_xor async_memcpy 956 2 raid456,async_raid6_recov async_tx 2008 5 raid456,async_raid6_recov,async_pq,async_xor,async_memcpy raid1 19757 0 raid0 5863 0 multipath 6055 0 linear 3605 0 md_mod 80386 6 raid10,raid456,raid1,raid0,multipath,linear ext3 110992 1 jbd 37434 1 ext3 ext2 55411 1 mbcache 4860 2 ext3,ext2 mmc_block 7658 4 ehci_hcd 35579 0 usbcore 122183 2 ehci_hcd mvsdio 5318 0 nls_base 5367 1 usbcore mv643xx_eth 22562 0 mmc_core 50206 2 mmc_block,mvsdio libphy 14836 1 mv643xx_eth inet_lro 5060 1 mv643xx_eth ** PCI devices: ** Sound cards: -- System Information: Debian Release: 6.0.3 APT prefers stable APT policy: (500, 'stable') Architecture: armel (armv5tel) Kernel: Linux 2.6.32-5-kirkwood Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash Versions of packages linux-image-2.6.32-5-kirkwood depends on: ii debconf [debconf-2.0] 1.5.36.1 Debian configuration management sy ii initramfs-tools [linux-initra 0.98.8 tools for generating an initramfs ii linux-base 2.6.32-38 Linux image base package ii module-init-tools 3.12-1 tools for managing Linux kernel mo Versions of packages linux-image-2.6.32-5-kirkwood recommends: pn firmware-linux-free <none> (no description available) ii uboot-mkimage 0.4 generate kernel image for U-Boot Versions of packages linux-image-2.6.32-5-kirkwood suggests: pn fdutils <none> (no description available) pn linux-doc-2.6.32 <none> (no description available) Versions of packages linux-image-2.6.32-5-kirkwood is related to: pn firmware-bnx2 <none> (no description available) pn firmware-bnx2x <none> (no description available) pn firmware-ipw2x00 <none> (no description available) pn firmware-ivtv <none> (no description available) pn firmware-iwlwifi <none> (no description available) pn firmware-linux <none> (no description available) pn firmware-linux-nonfree <none> (no description available) pn firmware-qlogic <none> (no description available) pn firmware-ralink <none> (no description available) pn xen-hypervisor <none> (no description available) -- debconf information: linux-image-2.6.32-5-kirkwood/postinst/bootloader-error-2.6.32-5-kirkwood: linux-image-2.6.32-5-kirkwood/postinst/bootloader-test-error-2.6.32-5-kirkwood: shared/kernel-image/really-run-bootloader: true linux-image-2.6.32-5-kirkwood/postinst/depmod-error-initrd-2.6.32-5-kirkwood: false linux-image-2.6.32-5-kirkwood/postinst/ignoring-do-bootloader-2.6.32-5-kirkwood: linux-image-2.6.32-5-kirkwood/postinst/missing-firmware-2.6.32-5-kirkwood: linux-image-2.6.32-5-kirkwood/prerm/would-invalidate-boot-loader-2.6.32-5-kirkwood: true linux-image-2.6.32-5-kirkwood/prerm/removing-running-kernel-2.6.32-5-kirkwood: true -- To UNSUBSCRIBE, email to debian-kernel-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org Archive: http://lists.debian.org/20111009172345.1302.41321.reportbug@sheeva
