--- Begin Message ---
Package: linux-2.6
Version: 2.6.38-2
Severity: critical
Justification: breaks the whole system
Booting...
Boot IO Dependent Code (IODC) revision 1
HARD Booted.
palo ipl 1.17 root@c3k Sun Mar 7 16:13:48 MST 2010
Skipping extended partition 6 - beyond reach of IPL
Partition Start(MB) End(MB) Id Type
1 1 31 f0 Palo
2 32 156 83 ext2
5 157 6832 83 ext2
PALO(F0) partition contains:
0/vmlinux64 6241289 bytes @ 0x48000
Command line for kernel: 'root=/dev/sda5 console=ttyS1 HOME=/
palo_kernel=2/vmlinux'
Selected kernel: /vmlinux from partition 2
Selected ramdisk: /initrd.img from partition 2
ELF64 executable
Entry 00100000 first 00100000 n 3
Segment 0 load 00100000 size 5419008 mediaptr 0x1000
Segment 1 load 006b9ce0 size 507616 mediaptr 0x52cce0
Segment 2 load 00738000 size 323008 mediaptr 0x5a9000
Loading ramdisk 14508363 bytes @ 3f218000...
Branching to kernel entry point 0x00100000. If this is the last
message you see, you may need to switch your console. This is
a common symptom -- search the FAQ and mailing list at parisc-linux.org
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.38-2-parisc64-smp (Debian 2.6.38-2)
(b...@decadent.org.uk) (gcc version 4.4.5 (GCC) ) #1 SMP Wed Mar 30 08:16:31
UTC 2011
[ 0.000000] unwind_init: start = 0x4053f000, end = 0x405728a0, entries =
13194
[ 0.000000] FP[0] enabled: Rev 1 Model 20
[ 0.000000] The 64-bit Kernel has started...
[ 0.000000] bootconsole [ttyB0] enabled
[ 0.000000] Initialized PDC Console for debugging.
[ 0.000000] Determining PDC firmware type: 64 bit PAT.
[ 0.000000] model 00008870 00000491 00000000 00000002 3e0505e7352af711
100000f0 00000008 000000b2 000000b2
[ 0.000000] vers 00000301
[ 0.000000] CPUID vers 20 rev 4 (0x00000284)
[ 0.000000] capabilities 0x35
[ 0.000000] model 9000/800/rp3440
[ 0.000000] parisc_cache_init: Only equivalent aliasing supported!
[ 0.000000] Memory Ranges:
[ 0.000000] 0) Start 0x0000000000000000 End 0x000000003fffffff Size 1024
MB
[ 0.000000] 1) Start 0x0000000100000000 End 0x000000027fdfffff Size 6142
MB
[ 0.000000] 2) Start 0x0000004040000000 End 0x00000040ffffffff Size 3072
MB
[ 0.000000] Total Memory: 10238 MB
[ 0.000000] initrd: 7f218000-7ffee14b
[ 0.000000] initrd: reserving 3f218000-3ffee14b (mem_max 27fe00000)
[ 0.000000] PERCPU: Embedded 10 pages/cpu @00000000428f5000 s11712 r8192
d21056 u40960
[ 0.000000] SMP: bootstrap CPU ID is 0
[ 0.000000] Built 3 zonelists in Zone order, mobility grouping on. Total
pages: 2585095
[ 0.000000] Kernel command line: root=/dev/sda5 console=ttyS1 HOME=/
palo_kernel=2/vmlinux
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 2097152 (order: 12, 16777216
bytes)
[ 0.000000] Inode-cache hash table entries: 1048576 (order: 11, 8388608
bytes)
[ 0.000000] Memory: 10273764k/10483712k available (3590k kernel code,
209948k reserved, 1649k data, 316k init)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] vmalloc : 0x0000000000008000 - 0x000000003f000000 (1007 MB)
[ 0.000000] memory : 0x0000000040000000 - 0x0000004140000000 (266240
MB)
[ 0.000000] .init : 0x0000000040738000 - 0x0000000040787000 ( 316 kB)
[ 0.000000] .data : 0x0000000040481b60 - 0x000000004061e020 (1649 kB)
[ 0.000000] .text : 0x0000000040100000 - 0x0000000040481b60 (3590 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=8,
Nodes=8
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] CONFIG_RCU_FANOUT set to non-default value of 32
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] NR_IRQS:128
[ 0.000000] Console: colour dummy device 160x64
[ 0.000000] Calibrating delay loop... 1597.44 BogoMIPS (lpj=3194880)
[ 0.096000] pid_max: default: 32768 minimum: 301
[ 0.096000] Security Framework initialized
[ 0.096000] SELinux: Disabled at boot.
[ 0.096000] Mount-cache hash table entries: 256
[ 0.104000] Initializing cgroup subsys ns
[ 0.104000] ns_cgroup deprecated: consider using the 'clone_children' flag
without the ns_cgroup.
[ 0.108000] Initializing cgroup subsys cpuacct
[ 0.108000] Initializing cgroup subsys devices
[ 0.116000] Initializing cgroup subsys freezer
[ 0.116000] Initializing cgroup subsys net_cls
[ 0.124000] Initializing cgroup subsys blkio
[ 0.124000] Brought up 1 CPUs
[ 0.124000] devtmpfs: initialized
[ 0.132000] print_constraints: dummy:
[ 0.132000] NET: Registered protocol family 16
[ 0.140000] EISA bus registered
[ 0.140000] Searching for devices...
[ 0.260000] Found devices:
[ 0.260000] 1. Storm Peak Slow at 0xfffffffffe780000 [128] { 0, 0x0, 0x887,
0x00004 }
[ 0.264000] 2. Storm Peak Slow at 0xfffffffffe781000 [129] { 0, 0x0, 0x887,
0x00004 }
[ 0.264000] 3. Storm Peak Slow at 0xfffffffffe798000 [152] { 0, 0x0, 0x887,
0x00004 }
[ 0.268000] 4. Storm Peak Slow at 0xfffffffffe799000 [153] { 0, 0x0, 0x887,
0x00004 }
[ 0.276000] 5. Everest Mako Memory at 0xfffffffffed08000 [8] { 1, 0x0,
0x0af, 0x00009 }
[ 0.284000] 6. Pluto BC McKinley Port at 0xfffffffffed00000 [0] { 12, 0x0,
0x880, 0x0000c }
[ 0.292000] 7. Mercury PCI Bridge at 0xfffffffffed20000 [0/0] { 13, 0x0,
0x783, 0x0000a }
[ 0.292000] 8. Mercury PCI Bridge at 0xfffffffffed22000 [0/1] { 13, 0x0,
0x783, 0x0000a }
[ 0.300000] 9. Mercury PCI Bridge at 0xfffffffffed24000 [0/2] { 13, 0x0,
0x783, 0x0000a }
[ 0.304000] 10. Mercury PCI Bridge at 0xfffffffffed26000 [0/3] { 13, 0x0,
0x783, 0x0000a }
[ 0.312000] 11. Mercury PCI Bridge at 0xfffffffffed28000 [0/4] { 13, 0x0,
0x783, 0x0000a }
[ 0.320000] 12. Mercury PCI Bridge at 0xfffffffffed2c000 [0/6] { 13, 0x0,
0x783, 0x0000a }
[ 0.328000] 13. Mercury PCI Bridge at 0xfffffffffed2e000 [0/7] { 13, 0x0,
0x783, 0x0000a }
[ 0.328000] 14. BMC IPMI Mgmt Ctlr at 0xfffffff0f05b0000 [16] { 15, 0x0,
0x004, 0x000c0 }
[ 0.336000] Enabling PDC_PAT chassis codes support v0.05
[ 0.892000] Releasing cpu 1 now, hpa=fffffffffe781000
[ 0.936000] FP[1] enabled: Rev 1 Model 20
[ 0.968000] Releasing cpu 2 now, hpa=fffffffffe798000
[ 1.016000] FP[2] enabled: Rev 1 Model 20
[ 1.044000] Releasing cpu 3 now, hpa=fffffffffe799000
[ 1.104000] FP[3] enabled: Rev 1 Model 20
[ 1.128000] CPU(s): 4 x PA8800 (Mako) at 800.006400 MHz
[ 1.132000] Setting cache flush threshold to 2000000 (4 CPUs online)
[ 1.172000] SBA found Pluto 2.3 at 0xfffffffffed00000
[ 1.372000] Mercury version TR3.2 (0x32) found at 0xfffffffffed20000
[ 1.448000] Mercury version TR3.2 (0x32) found at 0xfffffffffed22000
[ 1.528000] Mercury version TR3.2 (0x32) found at 0xfffffffffed24000
[ 1.604000] Mercury version TR3.2 (0x32) found at 0xfffffffffed26000
[ 1.680000] Mercury version TR3.2 (0x32) found at 0xfffffffffed28000
[ 1.760000] Mercury version TR3.2 (0x32) found at 0xfffffffffed2c000
[ 1.836000] Mercury version TR3.2 (0x32) found at 0xfffffffffed2e000
[ 1.892000] LBA: Truncating lmmio_space [fffffffff0000000/fffffffffecffffe]
to [fffffffff0000000,fffffffffe77ffff]
[ 1.896000] powersw: Soft power switch support not available.
[ 1.896000] bio: create slab <bio-0> at 0
[ 1.904000] vgaarb: device added:
PCI:0000:e0:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 1.904000] vgaarb: loaded
[ 1.916000] NET: Registered protocol family 2
[ 1.916000] IP route cache hash table entries: 524288 (order: 10, 4194304
bytes)
[ 1.924000] TCP established hash table entries: 262144 (order: 10, 4194304
bytes)
[ 1.932000] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 1.936000] TCP: Hash tables configured (established 262144 bind 65536)
[ 1.936000] TCP reno registered
[ 1.936000] UDP hash table entries: 8192 (order: 6, 262144 bytes)
[ 1.940000] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes)
[ 1.948000] NET: Registered protocol family 1
[ 2.016000] Unpacking initramfs...
[ 3.032000] Freeing initrd memory: 14168k freed
[ 3.036000] Chassis warnings not supported.
[ 3.036000] Performance monitoring counters enabled for Storm Peak Slow
[ 3.036000] audit: initializing netlink socket (disabled)
[ 3.036000] type=2000 audit(1302960532.036:1): initialized
[ 3.052000] VFS: Disk quotas dquot_6.5.2
[ 3.052000] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 3.080000] msgmni has been set to 20093
[ 3.080000] alg: No test for stdrng (krng)
[ 3.080000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major
253)
[ 3.084000] io scheduler noop registered
[ 3.084000] io scheduler deadline registered
[ 3.092000] io scheduler cfq registered (default)
[ 3.096000] PDC Stable Storage facility v0.30
[ 3.144000] STI GSC/PCI core graphics driver Version 0.9a
[ 3.144000] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 3.168000] 0000:e0:01.0: ttyS0 at MMIO 0xfffffffff4051000 (irq = 73) is a
16450
[ 3.208000] 0000:e0:01.1: ttyS1 at MMIO 0xfffffffff4050000 (irq = 73) is a
16550A
[ 3.212000] console [ttyS1] enabled, bootconsole disabled
[ 3.212000] console [ttyS1] enabled, bootconsole disabled
[ 3.232000] 0000:e0:01.1: ttyS2 at MMIO 0xfffffffff4050010 (irq = 73) is a
16550A
[ 3.252000] 0000:e0:01.1: ttyS3 at MMIO 0xfffffffff4050038 (irq = 73) is a
16550A
[ 3.256000] mousedev: PS/2 mouse device common for all mice
[ 3.256000] rtc-generic rtc-generic: rtc core: registered rtc-generic as rtc0
[ 3.264000] TCP cubic registered
[ 3.264000] NET: Registered protocol family 17
[ 3.264000] Registering the dns_resolver key type
[ 3.268000] registered taskstats version 1
[ 3.276000] rtc-generic rtc-generic: setting system clock to 2011-04-16
13:28:53 UTC (1302960533)
[ 3.376000] Freeing unused kernel memory: 316k freed
Loading, please wait...
[ 4.712000] udev[52]: starting version 164
[ 6.092000] usbcore: registered new interface driver usbfs
[ 6.092000] usbcore: registered new interface driver hub
[ 6.100000] usbcore: registered new device driver usb
[ 6.556000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.624000] ehci_hcd 0000:00:01.2: EHCI Host Controller
[ 6.624000] ehci_hcd 0000:00:01.2: new USB bus registered, assigned bus
number 1
[ 6.660000] ehci_hcd 0000:00:01.2: irq 68, io mem 0xffffffff80000000
[ 6.660000] SCSI subsystem initialized
[ 6.676000] ehci_hcd 0000:00:01.2: USB 2.0 started, EHCI 0.95
[ 6.676000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 6.676000] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 6.680000] usb usb1: Product: EHCI Host Controller
[ 6.680000] usb usb1: Manufacturer: Linux 2.6.38-2-parisc64-smp ehci_hcd
[ 6.720000] usb usb1: SerialNumber: 0000:00:01.2
[ 6.720000] hub 1-0:1.0: USB hub found
[ 6.720000] hub 1-0:1.0: 5 ports detected
[ 6.956000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 7.000000] ohci_hcd 0000:00:01.0: OHCI Host Controller
[ 7.004000] ohci_hcd 0000:00:01.0: new USB bus registered, assigned bus
number 2
[ 7.004000] ohci_hcd 0000:00:01.0: irq 66, io mem 0xffffffff80002000
[ 7.228000] tg3.c:v3.116 (December 3, 2010)
[ 7.872000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 7.872000] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 7.872000] usb usb2: Product: OHCI Host Controller
[ 7.872000] usb usb2: Manufacturer: Linux 2.6.38-2-parisc64-smp ohci_hcd
[ 7.880000] usb usb2: SerialNumber: 0000:00:01.0
[ 7.888000] hub 2-0:1.0: USB hub found
[ 7.888000] hub 2-0:1.0: 3 ports detected
Firmware Version 46.34
Duplex Console IO Dependent Code (IODC) revision 1
PROCESSOR PIM INFORMATION
Original Product Number: A7136A
Current Product Number: A7136A
----------------- Processor 0 HPMC Information - PDC Version: 46.34 ------
Timestamp = Sat Apr 16 13:28:57 GMT 2011 (20:11:04:16:13:28:57)
HPMC Chassis Codes
Chassis Code Extension
------------ ---------
0xe800035c00e00000 0x00000000403451b4
0x57000f7300e00000 0x8040004000000000
0xf600105e00e00000 0xfffffff0f0c00000
0x140003b200e00000 0x000000000000000b
0x5600100b00e00000 0x0000000000000194
0x5600106400e00000 0xfffffff0f0435110
General Registers 0 - 31
00-03 0000000000000000 000000004072d8c0 0000000040128ebc 000000007f5cc000
04-07 000000001c5fc000 000000000800000f 0000000000000000 0000000000000000
08-11 000000007f5cc000 000000007f99cbb0 0000000000000000 0000000000020690
12-15 0000000000000000 00000000000205e0 000000000001e128 000000000001d18a
16-19 00000000fb3e82d0 000000000001a000 000000000001ac94 000000000000fffc
20-23 000000004069d278 0000000000000000 ffffffffc0000000 0000000000100000
24-27 000000000000000a 00000000003c8002 000000007eca0800 00000000407118c0
28-31 000000000002c000 000000007f99cf40 000000007f99cf70 0000000000000002
Control Registers 0 - 31
00-03 0000000000000000 0000000000000000 0000000000000000 0000000000000000
04-07 0000000000000000 0000000000000000 0000000000000000 0000000000000000
08-11 0000000000000078 0000000000000000 00000000000000c0 0000000000000001
12-15 0000000000000000 0000000000000000 0000000000103000 ffe0000000000000
16-19 00000077cb22f1cc 0000000000000000 00000000403451b4 00000000503f02b0
20-23 0000000000340001 00000000cb72da18 000000ff0804ff0e 0000000000000000
24-27 0000000000621000 000000003f9c2000 fffdffffffdfffef 0000000040001540
28-31 0000000040001540 ffffffffffffff7f 000000007f99c000 886904b488140042
Space Registers 0 - 7
00-03 0000000000012000 0000000000000000 0000000000000000 000000000001e000
04-07 0000000000000000 0000000000000000 0000000000000000 0000000000000000
IIA Space (back entry) = 0x0000000000000000
IIA Offset (back entry) = 0x00000000403451b8
Check Type = 0x20000000
Cpu State = 0x9e000000
Cache Check = 0x00000000
TLB Check = 0x00000000
Bus Check = 0x00000000
Assists Check = 0x0001e000
Assist State = 0x00000000
Path Info = 0x00000000
System Responder Address = 0x0000000000000000
System Requestor Address = 0x0000000000000000
Floating Point Registers 0 - 31
00-03 0000000000000000 0000000000000000 0000000000000000 0000000000000000
04-07 0000000000000001 0000000040787000 0000000040787000 00000000407118c0
08-11 000000000004f000 00000000407348c0 000000007ec603b8 00000000404d74f0
12-15 0000000000000003 000000000005bcc0 0000000000000000 0000000000000000
16-19 000000000000bcc0 0000000000000000 00000000407348c0 0000000000000001
20-23 000000000000ea60 0000000000000500 0000000000000000 0000000000000000
24-27 0000000000000000 0000000000000000 00000000407230c0 00000000407230c0
28-31 00000000407230c0 000000000000000f 00000000405b31e8 00000000407238c0
PIM Revision = 0x0000000000000001
CPU ID = 0x0000000000000014
CPU Revision = 0x0000000000000031
Cpu Serial Number = 0x46100b89e43f0503
Check Summary = 0x8040004000000000
SAL Timestamp = 0x000000004da99999
System Firmware Rev. = 0x00000ba20000121a
PDC Relocation Address = 0xfffffff0f0c00000
Available Memory = 0x000000027fe00000
CPU Diagnose Register 2 = 0x3112022000002008
MIB_STAT = 0x0040000000200000
MIB_LOG1 = 0x0000000000555500
MIB_LOG2 = 0x0000800000000000
MIB_ECC_DATA = 0x808800007fffbfd8
ICache Info = 0x0000000000000000
DCache Info = 0x0000000000000000
Sharedcache Info1 = 0x0000000000000000
Sharedcache Info2 = 0x0000000000000080
MIB_RSLOG1 = 0x0000000000000004
MIB_RSLOG2 = 0x0000010000000000
MIB_RQLOG = 0x00002580001e1510
MIB_REQLOGa = 0x8000000000000200
MIB_REQLOGb = 0x01000aa400000000
Reserved = 0x0000000000000000
Cache Repair Detail = 0x0000000000000000
PIM Detail Text:
-------------- Memory Error Log Information --------------
No errors logged for this bus
------------ I/O Module Error Log Information ------------
IO Subsystem Log Entries
Found 1 PCI Comp error
Found 1 PCI Bus error
------------------------------------------------
Detail display of IO subsystem log entries
------------------------------------------
PCI Component Error information
PCI Component Error 1
--- Section Header ---
GUID
data1 0xe429faf6
data2 0x3cb7
data3 0x11d4
datat4 0xbc a7 0 80 c7 3c 88 81
REVISION 0x0200
ERROR_RECOVERY_INFO 0x80
SECTION_LENGTH 0x00000188
VALIDATION_BITS 0x0000000000000023
PCI_COMP_ERROR_STATUS 0x00000000005a2000
PCI_COMP_INFO 0x0000000000004a7c 0x0035103303104100
Vendor Id/Device Id: 0x35/1033
Base Class/Sub Class/Program Interface: 0x41/10/3
Segment/Bus/Device/Function: 0x0/0/1/0
PCI_COMP_MEM_NUM 0
PCI_COMP_IO_NUM 0
PCI_COMP_REGS_DATA_PAIR
Address Data
0x0000000000000000 0x0000000000000000
0x0000000000000000 0x0000000000000000
0x0000000000000000 0x0000000000000000
0x0000000000000000 0x0000000000000000
0x0000000000000000 0x0000000000000000
0x0000000000000000 0x0000000000000000
PCI_COMP_OEM_DATA_STRUCT
--- Section Header ---
GUID
data1 0x4f7d86a
data2 0x598b
data3 0x4a0a
data4 0xaa 62 ff 70 73 46 67 4d
LENGTH 232
PHYSICAL_LOCATION 0xffffffffffffff00
REGISTRATION_NUMBER 0x0000000000000008
CONFIG_REGISTERS_DATA
Offset Size Data
0 8 0x2210014600351033
8 8 0x008080200c031041
16 8 0x0000000080002000
24 8 0x0000000000000000
32 8 0x0000000000000000
40 8 0x0035103300000000
48 8 0x0000004000000000
56 8 0x2a01010000000000
0 0 0x0000000000000000
0 0 0x0000000000000000
0 0 0x0000000000000000
0 0 0x0000000000000000
End of PCI Component Error Information for Error 1
PCI Bus Error information
PCI Bus Error 1
--- Section Header ---
GUID
data1 0xe429faf4
data2 0x3cb7
data3 0x11d4
data4 0xbc a7 0 80 c7 3c 88 81
REVISION 0x0200
ERROR_RECOVERY_INFO 0x84
SECTION_LENGTH 0x00000108
VALIDATION_BITS 0x000000000000074f
PCI_BUS_ERROR_STATUS 0x00000000005a2000
PCI_BUS_ERROR_TYPE 0x0000000000000004
PCI_BUS_ID 0x0000000000000000
PCI_BUS_ADDRESS 0x0000000000000d20
PCI_BUS_DATA 0x0000000000000000
PCI_BUS_CMD 0x0000000000000000
PCI_BUS_REQUESTOR_ID 0x00000000fed20000
PCI_BUS_COMPLETER_ID 0x0000000000000000
PCI_BUS_TARGET_ID 0x0000000000000d20
PCI_BUS_OEM_ID 0x0000000000003d90
Bus OEM Data
CEC Header:
--- OEM Data Header ---
GUID
data1 0x9fe64482
data2 0xa02d
data3 0x4ef7
data4 0xad e6 c6 63 59 62 53 99
--- OEM Data Body ---
CELL_NUMBER 0
SBA_NUMBER 0
ROPE_NUMBER 0
--- Mercury Info ---
ERROR_STATUS 0x000000010000021c
ERROR_MASTER_ID_LOG 0x0000000000000000
INBOUND_ERR_ADDRESS 0x0000000000000000
INBOUND_ERR_ATTRIBUTE 0x0000000000000000
COMPLETION_MESSAGE_LOG 0x0000000000000000
OUTBOUND_ERR_ADDRESS 0x0000000000000d20
ERROR_CONFIG 0x0000000000000030
STATUS_INFO_CONTROL 0x0000000000000000
FUNC_ID 0x22b00146122e103c
CAPABILITIES_LIST 0x0f00023700200002
AGP_COMMAND 0x0000000000000000
PCIX_CAPABILITIES 0x0013ff0000010007
OLR_CONTROL 0x00023f1b00032403
CLOCK_CONTROL 0x0000000000000048
BUS_MODE 0xa1a974ae36f58460
End of PCI Bus Error Information for Error 1
End of PCI Bus Error Information
0000000040345188 <lba_pat_out8>:
40345188: 53 5c 03 30 ldd 198(r26),ret0
4034518c: db 39 0b f0 extrd,u r25,63,16,r25
40345190: d6 7f 18 52 depwi,z -1,29,14,r19
40345194: db 3f 0b fe extrd,u r25,63,2,r31
40345198: 0a 79 02 19 and r25,r19,r25
4034519c: f3 39 11 4a depd,z r25,53,54,r25
403451a0: 0b f9 0a 19 add,l r25,r31,r25
403451a4: 0b 3c 0a 19 add,l ret0,r25,r25
403451a8: 0f 38 12 00 stb r24,0(r25)
403451ac: 2b 6e 00 00 addil L%1c000,dp,r1
403451b0: 0f 40 10 dc ldd 0(r26),ret0
403451b4: 50 3f 02 b0 ldd 158(r1),r31
403451b8: 0f 80 10 9c ldw 0(ret0),ret0
403451bc: e8 40 d0 00 bve (rp)
403451c0: 0f fc 12 80 stw ret0,0(r31)
403451c4: 00 00 00 00 break 0,0
-- Package-specific info:
** Kernel log: boot messages should be attached
** Model information
model : 9000/800/rp3440
model name : Storm Peak Slow
hversion : 0x00008870
sversion : 0x00000491
model : 9000/800/rp3440
model name : Storm Peak Slow
hversion : 0x00008870
sversion : 0x00000491
model : 9000/800/rp3440
model name : Storm Peak Slow
hversion : 0x00008870
sversion : 0x00000491
model : 9000/800/rp3440
model name : Storm Peak Slow
hversion : 0x00008870
sversion : 0x00000491
** Network interface configuration:
auto lo
iface lo inet loopback
allow-hotplug eth0
iface eth0 inet static
address 132.246.10.88
netmask 255.255.255.240
network 132.246.10.80
broadcast 132.246.10.95
gateway 132.246.10.81
dns-nameservers 132.246.161.100 132.246.161.200 132.246.10.84
dns-search hia.nrc.ca
** PCI devices:
00:01.0 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 41)
(prog-if 10 [OHCI])
Subsystem: NEC Corporation Hama USB 2.0 CardBus [1033:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 128 (250ns min, 10500ns max), Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 66
Region 0: Memory at ffffffff80002000 (32-bit, non-prefetchable)
[size=4K]
Capabilities: <access denied>
00:01.1 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 41)
(prog-if 10 [OHCI])
Subsystem: NEC Corporation Hama USB 2.0 CardBus [1033:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 128 (250ns min, 10500ns max), Cache Line Size: 128 bytes
Interrupt: pin B routed to IRQ 67
Region 0: Memory at ffffffff80001000 (32-bit, non-prefetchable)
[size=4K]
Capabilities: <access denied>
00:01.2 USB Controller [0c03]: NEC Corporation USB 2.0 [1033:00e0] (rev 02)
(prog-if 20 [EHCI])
Subsystem: NEC Corporation USB 2.0 [1033:00e0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 128 (4000ns min, 8500ns max), Cache Line Size: 128 bytes
Interrupt: pin C routed to IRQ 68
Region 0: Memory at ffffffff80000000 (32-bit, non-prefetchable)
[size=256]
Capabilities: <access denied>
00:02.0 IDE interface [0101]: Silicon Image, Inc. SiI 0649 Ultra ATA/100 PCI to
ATA Host Controller [1095:0649] (rev 02) (prog-if 8f [Master SecP SecO PriP
PriO])
Subsystem: Silicon Image, Inc. SiI 0649 Ultra ATA/100 PCI to ATA Host
Controller [1095:0649]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 128 (500ns min, 1000ns max)
Interrupt: pin A routed to IRQ 69
Region 0: I/O ports at 0d18 [size=8]
Region 1: I/O ports at 0d24 [size=4]
Region 2: I/O ports at 0d10 [size=8]
Region 3: I/O ports at 0d20 [size=4]
Region 4: I/O ports at 0d00 [size=16]
Capabilities: <access denied>
20:01.0 SCSI storage controller [0100]: LSI Logic / Symbios Logic 53c1010 66MHz
Ultra3 SCSI Adapter [1000:0021] (rev 01)
Subsystem: LSI Logic / Symbios Logic LSI53C1000/1000R/1010R/1010-66 PCI
to Ultra160 SCSI Controller [1000:1000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 192 (4250ns min, 4500ns max), Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 70
Region 0: I/O ports at 12100 [size=256]
Region 1: Memory at ffffffff90015000 (64-bit, non-prefetchable)
[size=1K]
Region 3: Memory at ffffffff90012000 (64-bit, non-prefetchable)
[size=8K]
Capabilities: <access denied>
Kernel driver in use: sym53c8xx
20:01.1 SCSI storage controller [0100]: LSI Logic / Symbios Logic 53c1010 66MHz
Ultra3 SCSI Adapter [1000:0021] (rev 01)
Subsystem: LSI Logic / Symbios Logic LSI53C1000/1000R/1010R/1010-66 PCI
to Ultra160 SCSI Controller [1000:1000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 192 (4250ns min, 4500ns max), Cache Line Size: 128 bytes
Interrupt: pin B routed to IRQ 71
Region 0: I/O ports at 12000 [size=256]
Region 1: Memory at ffffffff90014000 (64-bit, non-prefetchable)
[size=1K]
Region 3: Memory at ffffffff90010000 (64-bit, non-prefetchable)
[size=8K]
Capabilities: <access denied>
Kernel driver in use: sym53c8xx
20:02.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5701
Gigabit Ethernet [14e4:1645] (rev 15)
Subsystem: Hewlett-Packard Company Core Lan 1000Base-T [103c:12a4]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 128 (16000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 72
Region 0: Memory at ffffffff90000000 (64-bit, non-prefetchable)
[size=64K]
Capabilities: <access denied>
Kernel driver in use: tg3
e0:01.0 Communication controller [0780]: Hewlett-Packard Company Auxiliary Diva
Serial Port [103c:1290] (rev 01)
Subsystem: Hewlett-Packard Company Diva SP2 [103c:1291]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 128, Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 73
Region 2: Memory at fffffffff4051000 (32-bit, non-prefetchable)
[size=16]
Capabilities: <access denied>
Kernel driver in use: serial
e0:01.1 Serial controller [0700]: Hewlett-Packard Company Diva Serial [GSP]
Multiport UART [103c:1048] (rev 03) (prog-if 02 [16550])
Subsystem: Hewlett-Packard Company Everest SP2 [103c:1282]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 73
Region 0: Memory at fffffffff4050000 (32-bit, non-prefetchable)
[size=4K]
Region 2: Memory at fffffffff4020000 (32-bit, prefetchable) [size=128K]
Capabilities: <access denied>
Kernel driver in use: serial
e0:02.0 VGA compatible controller [0300]: ATI Technologies Inc Radeon RV100 QY
[Radeon 7000/VE] [1002:5159] (prog-if 00 [VGA controller])
Subsystem: Hewlett-Packard Company Radeon 7000 [103c:1292]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 128 (2000ns min), Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 74
Region 0: Memory at fffffffff0000000 (32-bit, prefetchable) [size=64M]
Region 1: I/O ports at 6e000 [size=256]
Region 2: Memory at fffffffff4040000 (32-bit, non-prefetchable)
[size=64K]
Expansion ROM at fffffffff4000000 [disabled] [size=128K]
Capabilities: <access denied>
** USB devices:
not available
-- System Information:
Debian Release: wheezy/sid
APT prefers oldstable
APT policy: (500, 'oldstable'), (500, 'unstable'), (500, 'testing')
Architecture: hppa (parisc64)
Kernel: Linux 2.6.39-rc2+ (SMP w/4 CPU cores)
Locale: LANG=en_CA.UTF-8, LC_CTYPE=en_CA.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.38-2-parisc64-smp depends on:
ii debconf [debconf-2.0] 1.5.38 Debian configuration management sy
ii initramfs-tools [linux-initra 0.98.8 tools for generating an initramfs
ii linux-base 3.2 Linux image base package
ii module-init-tools 3.12-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.38-2-parisc64-smp recommends:
ii firmware-linux-free 3 Binary firmware for various driver
Versions of packages linux-image-2.6.38-2-parisc64-smp suggests:
pn linux-doc-2.6.38 <none> (no description available)
ii palo 1.18 Linux boot loader for parisc/hppa
Versions of packages linux-image-2.6.38-2-parisc64-smp is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information:
linux-image-2.6.38-2-parisc64-smp/prerm/removing-running-kernel-2.6.38-2-parisc64-smp:
true
linux-image-2.6.38-2-parisc64-smp/postinst/missing-firmware-2.6.38-2-parisc64-smp:
linux-image-2.6.38-2-parisc64-smp/postinst/ignoring-do-bootloader-2.6.38-2-parisc64-smp:
linux-image-2.6.38-2-parisc64-smp/postinst/depmod-error-initrd-2.6.38-2-parisc64-smp:
false
--- End Message ---
--- Begin Message ---
Source: user-mode-linux
Source-Version: 2.6.32-1um-4+37
We believe that the bug you reported is fixed in the latest version of
user-mode-linux, which is due to be installed in the Debian FTP archive:
user-mode-linux_2.6.32-1um-4+37.diff.gz
to main/u/user-mode-linux/user-mode-linux_2.6.32-1um-4+37.diff.gz
user-mode-linux_2.6.32-1um-4+37.dsc
to main/u/user-mode-linux/user-mode-linux_2.6.32-1um-4+37.dsc
user-mode-linux_2.6.32-1um-4+37_amd64.deb
to main/u/user-mode-linux/user-mode-linux_2.6.32-1um-4+37_amd64.deb
A summary of the changes between this version and the previous one is
attached.
Thank you for reporting the bug, which will now be closed. If you
have further comments please address them to 622...@bugs.debian.org,
and the maintainer will reopen the bug report if appropriate.
Debian distribution maintenance software
pp.
dann frazier <da...@debian.org> (supplier of updated user-mode-linux package)
(This message was generated automatically at their request; if you
believe that there is a problem with it please contact the archive
administrators by mailing ftpmas...@debian.org)
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Format: 1.8
Date: Thu, 29 Sep 2011 20:23:36 -0600
Source: user-mode-linux
Binary: user-mode-linux
Architecture: source amd64
Version: 2.6.32-1um-4+37
Distribution: stable
Urgency: high
Maintainer: User Mode Linux Maintainers <pkg-uml-p...@lists.alioth.debian.org>
Changed-By: dann frazier <da...@debian.org>
Description:
user-mode-linux - User-mode Linux (kernel)
Closes: 566522 620848 622259 622745 622997 627700 627702 627704 627705 630730
631465 632778 637659 637848 638656 638956 639425 639426 640650 641232 641419
642380
Changes:
user-mode-linux (2.6.32-1um-4+37) stable; urgency=high
.
* Rebuild against linux-source-2.6.32 (2.6.32-37):
* pm: Fix definition of SET_SYSTEM_SLEEP_PM_OPS used in backported drivers
(fixes FTBFS on ia64)
* splice: Fix write position in output file (Closes: #641419)
* PCI: Add definition of pci_pcie_cap(), used in backported e1000e
(fixes FTBFS on armel, mips, mipsel, sparc)
* [openvz] cpt: Allow ext4 mounts (Closes: #642380)
* Add drm change from 2.6.32.41+drm33.18:
- drm/radeon/kms: fix bad shift in atom iio table parser
* [opvenz] ptrace: Don't allow to trace a process without memory map.
* Add drm change from 2.6.32.42+drm33.19, including:
- drm/i915: Add a no lvds quirk for the Asus EeeBox PC EB1007
- drm/radeon/kms: fix for radeon on systems >4GB without hardware iommu
* Add longterm release 2.6.32.43, including:
- ksm: fix NULL pointer dereference in scan_get_next_rmap_item()
(CVE-2011-2183)
- TTY: ldisc, do not close until there are readers
- uvcvideo: Remove buffers from the queues when freeing
- inet_diag: fix inet_diag_bc_audit() (CVE-2011-2213)
- net: filter: Use WARN_RATELIMIT
- af_packet: prevent information leak
- ipv6/udp: Use the correct variable to determine non-blocking condition
- mm: prevent concurrent unmap_mapping_range() on the same inode
For the complete list of changes, see:
http://www.kernel.org/pub/linux/kernel/v2.6/longterm/v2.6.32/ChangeLog-2.6.32.43
and the bug report which this closes: #637848.
* Add longterm release 2.6.32.42, including:
- ftrace: Only update the function code on write to filter files
- kmemleak: Do not return a pointer to an object that kmemleak did not
get
- ext3: Fix fs corruption when make_indexed_dir() fails
- jbd: fix fsync() tid wraparound bug
- PCI: allow matching of prefetchable resources to non-prefetchable
windows
(Closes: #637659)
- loop: handle on-demand devices correctly
- xhci: Fix full speed bInterval encoding; fix interval calculation for
FS isoc endpoints (regressions in 2.6.32-34)
- OHCI: fix regression caused by nVidia shutdown workaround
(regression in 2.6.32-31)
- brd: handle on-demand devices correctly
- xen mmu: fix a race window causing leave_mm BUG()
- SCSI: Fix oops caused by queue refcounting failure
- fat: Fix corrupt inode flags when remove ATTR_SYS flag
- pata_cm64x: fix boot crash on parisc (Closes: #622745, #622997)
- Revert "iwlagn: Support new 5000 microcode." (Closes: #632778)
For the complete list of changes, see:
http://www.kernel.org/pub/linux/kernel/v2.6/longterm/v2.6.32/ChangeLog-2.6.32.42
and the bug report which this closes: #631465.
* [vserver] Update patch to 2.6.32.41-vs2.3.0.36.29.7
- Apply sched changes deferred from 2.6.32.29
* e1000e: Backport changes up to Linux 2.6.38 (Closes: #627700)
- Add support for i82567V-4 and i82579
- Fix support for i82577, i82578 and i82583
* e1000e: Fix selection of alternate MAC address on device id 0x1060
(regression in 2.6.34)
* igb,igbvf: Backport changes up to Linux 3.0.4 (Closes: #627702)
- Add support for i82576-ET2, i82580, DH89xxCC, i340 and i350
* r8169: Backport changes up to Linux 3.0.2 (Closes: #627704)
- Fix support for RTL8102E and RTL8168DP
- Add support for RTL8105E, RTL8168E and another variant of RTL8168DP
- Add support for D-Link DGE-530T rev C1
* tg3,broadcom: Backport changes up to Linux 2.6.38 (Closes: #627705)
- Add support for BCM5717, BCM5719, BCM57765
- Add support for BCM50610M and BCM5241 PHYs
- Fix support for BCM5755
* Remove net device features from bug reports (Closes: #638956)
* Revert "net/ipv4: Check for mistakenly passed in non-IPv4 address"
included in 2.6.32.43, which might break some applications
* Add longterm release 2.6.32.44, including:
- NFSv4.1: update nfs4_fattr_bitmap_maxsz
- hwmon: (max1111) Fix race condition causing NULL pointer exception
- bridge: send proper message_age in config BPDU
- USB: OHCI: fix another regression for NVIDIA controllers
(Closes: #620848)
- ext3: Fix oops in ext3_try_to_allocate_with_rsv()
- svcrpc: fix list-corrupting race on nfsd shutdown
- alpha: fix several security issues (CVE-2011-2208, CVE-2011-2209,
CVE-2011-2210, CVE-2011-2211)
- ALSA: sound/core/pcm_compat.c: adjust array index
- atm: [br2684] allow routed mode operation again
For the complete list of changes, see:
http://www.kernel.org/pub/linux/kernel/v2.6/longterm/v2.6.32/ChangeLog-2.6.32.44
and the bug report which this closes: #639425.
* Add longterm release 2.6.32.45, including:
- ALSA: timer - Fix Oops at closing slave timer
For the complete list of changes, see:
http://www.kernel.org/pub/linux/kernel/v2.6/longterm/v2.6.32/ChangeLog-2.6.32.45
and the bug report which this closes: #639426.
* sched: Work around sched_group::cpu_power == 0 (Ameliorates: #636797)
* [x86] Revert "x86, hotplug: Use mwait to offline a processor, fix the
legacy case" (Closes: #622259)
* Fix bugs in IPv6 forwarding with GRO/GSO (Closes: #630730):
- e1000e,igb,igbvf,ixgbe: Fix IPv6 GSO type checks
- ipv6: Add GSO support on forwarding path
* devpts: correctly check d_alloc_name() return code (Closes: #640650)
* ipv6: make fragment identifications less predictable (CVE-2011-2699)
* Add longterm release 2.6.32.46, including:
- atm: br2864: sent packets truncated in VC routed mode (Closes: #638656)
- hwmon: (ibmaem) add missing kfree
- ALSA: snd-usb-caiaq: Correct offset fields of outbound iso_frame_desc
- ALSA: snd_usb_caiaq: track submitted output urbs
- futex: Fix regression with read only mappings
- x86-32, vdso: On system call restart after SYSENTER, use int $0x80
- fuse: check size of FUSE_NOTIFY_INVAL_ENTRY message
For the complete list of changes, see:
http://www.kernel.org/pub/linux/kernel/v2.6/longterm/v2.6.32/ChangeLog-2.6.32.46
and the bug report which this closes: #641232.
* drm/ttm: fix ttm_bo_add_ttm(user) failure path
* 3c503: fix broken IRQ autoprobing (Closes: #566522)
Checksums-Sha1:
1869e4e3bd2255256fd88bc2aa88a25d091c7d73 2030
user-mode-linux_2.6.32-1um-4+37.dsc
73f04e650f2499dd02305298445072482658725e 17952
user-mode-linux_2.6.32-1um-4+37.diff.gz
2bb102c3be4aa861b343fe0c23e82774ebd67ecc 7079528
user-mode-linux_2.6.32-1um-4+37_amd64.deb
Checksums-Sha256:
eed0a5cfbe40d929734f9d69eb92582b93c637ccf943ecc7bdcd6879cb372d6a 2030
user-mode-linux_2.6.32-1um-4+37.dsc
ebf8970ea4b463ad781f9d70ac6e366f79876b181b200403b71f5731922462e4 17952
user-mode-linux_2.6.32-1um-4+37.diff.gz
15d735560016bef67c765b55eb69e7946895fe96cea980597462a49150bf116a 7079528
user-mode-linux_2.6.32-1um-4+37_amd64.deb
Files:
211981a8378401bd4a2e23930d597f3e 2030 kernel extra
user-mode-linux_2.6.32-1um-4+37.dsc
bdf1b260c42d7fceb8156eb4259a1682 17952 kernel extra
user-mode-linux_2.6.32-1um-4+37.diff.gz
037c61fd01e7007d7dfc613b68ddc90d 7079528 kernel extra
user-mode-linux_2.6.32-1um-4+37_amd64.deb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=6K8r
-----END PGP SIGNATURE-----
--- End Message ---
