Package: linux-2.6 Version: 3.0.0-1 Severity: normal Tags: ipv6 *** Please type your report below this line *** The loongson-2f stock kernel on debian comes with ipv6 compiled as a module. However that's not expected by procps. See:
/usr/share/doc/procps/README.Debian ... ipv6 sysctl keys ---------------- Modern Debian kernel packages have the IPv6 module compiled in by default. This means that the /proc/sys/net/ipv6 directory exists when the procps startup script runs. However if you make your own kernel then you may make ipv6 a module and get a race condition between the netbase and procps startup scripts. This is because netbase, by default, causes ipv6 module to be loaded but they don't (and cannot) depend on each-other. The solution is to either: - Not put ipv6 keys into /etc/sysctl.d/* or /etc/sysctl.conf - Compile the ipv6 module into the kernel - Load the module early by putting ipv6 into /etc/modules - Make a init script dependency by adding netbase to the Required-Start line in /etc/init.d/procps ... Tha clearly states the debian stock kernels should have no problem given that they come with ipv6 built inside. However loongson-2f stock kernels don't comply with this. This causes failures like: error: "net.ipv6.bindv6only" is an unknown key Work around is really simple, just to add ipv6 into /etc/modules, however that shouldn't be the case for stock kernels according to procps documentation, and also a bug filed for that purpose last year (closed already): http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=507788 Any ways, just the loongson-2f kernel not being compliant with procps suppositions, :-) Thanks, Javier. -- Package-specific info: ** Version: Linux version 3.0.0-1-loongson-2f (Debian 3.0.0-1) (b...@decadent.org.uk) (gcc version 4.5.3 (Debian 4.5.3-3) ) #1 Mon Jul 25 21:17:28 UTC 2011 ** Command line: console=tty machtype=lemote-fuloong-2f-box root=/dev/sda6 video=sisfb:1280x1024-24@60 resume=/dev/sda5 PMON_VER=LM6004-1.3.6 EC_VER=undefined machtype=lemote-fuloong-2f-box ** Not tainted ** Kernel log: [ 2.088000] PM: Hibernation image partition 8:5 present [ 2.088000] PM: Looking for hibernation image. [ 2.092000] PM: Image not found (code -22) [ 2.092000] PM: Hibernation image not present or could not be loaded. [ 2.092000] registered taskstats version 1 [ 2.092000] /build/buildd-linux-2.6_3.0.0-1-mipsel-TFQf1R/linux-2.6-3.0.0/debian/build/source_mipsel_none/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 2.096000] Initializing network drop monitor service [ 2.120000] EXT3-fs: barriers not enabled [ 2.128000] kjournald starting. Commit interval 5 seconds [ 2.128000] EXT3-fs (sda6): mounted filesystem with ordered data mode [ 2.128000] VFS: Mounted root (ext3 filesystem) readonly on device 8:6. [ 2.132000] Freeing unused kernel memory: 240k freed [ 4.312000] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 4.312000] r8169 0000:00:06.0: (unregistered net_device): no PCI Express capability [ 4.312000] r8169 0000:00:06.0: eth0: RTL8169sc/8110sc at 0x9000000050072000, 00:23:9e:00:0f:62, XID 18000000 IRQ 36 [ 4.480000] cpufreq: Loongson-2F CPU frequency driver. [ 4.540000] usbcore: registered new interface driver usbfs [ 4.556000] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0 [ 4.604000] usbcore: registered new interface driver hub [ 4.612000] rtc0: alarms up to one day, 114 bytes nvram [ 4.644000] usbcore: registered new device driver usb [ 4.688000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.744000] PCI: Setting latency timer of device 0000:00:0e.5 to 64 [ 4.744000] ehci_hcd 0000:00:0e.5: EHCI Host Controller [ 4.776000] ehci_hcd 0000:00:0e.5: new USB bus registered, assigned bus number 1 [ 4.828000] ehci_hcd 0000:00:0e.5: irq 11, io mem 0x50071000 [ 4.848000] ehci_hcd 0000:00:0e.5: USB 0.0 started, EHCI 1.00 [ 4.888000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 4.892000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.896000] usb usb1: Product: EHCI Host Controller [ 4.900000] usb usb1: Manufacturer: Linux 3.0.0-1-loongson-2f ehci_hcd [ 4.904000] usb usb1: SerialNumber: 0000:00:0e.5 [ 4.924000] hub 1-0:1.0: USB hub found [ 4.944000] hub 1-0:1.0: 4 ports detected [ 4.996000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 5.004000] PCI: Enabling device 0000:00:0e.4 (0000 -> 0002) [ 5.036000] PCI: Setting latency timer of device 0000:00:0e.4 to 64 [ 5.036000] ohci_hcd 0000:00:0e.4: OHCI Host Controller [ 5.044000] ohci_hcd 0000:00:0e.4: new USB bus registered, assigned bus number 2 [ 5.064000] ohci_hcd 0000:00:0e.4: irq 11, io mem 0x50070000 [ 5.156000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 5.160000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.164000] usb usb2: Product: OHCI Host Controller [ 5.168000] usb usb2: Manufacturer: Linux 3.0.0-1-loongson-2f ohci_hcd [ 5.172000] usb usb2: SerialNumber: 0000:00:0e.4 [ 5.180000] hub 2-0:1.0: USB hub found [ 5.188000] hub 2-0:1.0: 4 ports detected [ 5.372000] PCI: Setting latency timer of device 0000:00:0e.3 to 64 [ 5.568000] usb 2-3: new low speed USB device number 2 using ohci_hcd [ 5.804000] usb 2-3: New USB device found, idVendor=04d9, idProduct=1702 [ 5.808000] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 5.812000] usb 2-3: Product: USB Keyboard [ 5.816000] usb 2-3: Manufacturer: [ 6.008000] usb 2-4: new low speed USB device number 3 using ohci_hcd [ 6.176000] input: USB Keyboard as /devices/pci0000:00/0000:00:0e.4/usb2/2-3/2-3:1.0/input/input0 [ 6.188000] generic-usb 0003:04D9:1702.0001: input,hidraw0: USB HID v1.10 Keyboard [ USB Keyboard] on usb-0000:00:0e.4-3/input0 [ 6.220000] input: USB Keyboard as /devices/pci0000:00/0000:00:0e.4/usb2/2-3/2-3:1.1/input/input1 [ 6.232000] generic-usb 0003:04D9:1702.0002: input,hidraw1: USB HID v1.10 Device [ USB Keyboard] on usb-0000:00:0e.4-3/input1 [ 6.240000] usb 2-4: New USB device found, idVendor=0458, idProduct=003a [ 6.244000] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 6.248000] usb 2-4: Product: Optical Mouse [ 6.252000] usb 2-4: Manufacturer: Genius [ 6.280000] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:0e.4/usb2/2-4/2-4:1.0/input/input2 [ 6.296000] generic-usb 0003:0458:003A.0003: input,hidraw2: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:0e.4-4/input0 [ 6.312000] usbcore: registered new interface driver usbhid [ 6.316000] usbhid: USB HID core driver [ 9.908000] Adding 3903744k swap on /dev/sda5. Priority:-1 extents:1 across:3903744k [ 11.060000] EXT3-fs (sda6): using internal journal [ 11.508000] loop: module loaded [ 11.652000] fuse init (API version 7.16) [ 17.520000] EXT3-fs: barriers not enabled [ 17.532000] kjournald starting. Commit interval 5 seconds [ 17.536000] EXT3-fs (sda1): using internal journal [ 17.540000] EXT3-fs (sda1): mounted filesystem with ordered data mode [ 17.744000] EXT4-fs (sda7): mounted filesystem with ordered data mode. Opts: (null) [ 17.848000] EXT4-fs (sda8): mounted filesystem with ordered data mode. Opts: (null) [ 17.992000] EXT4-fs (sda9): mounted filesystem with ordered data mode. Opts: (null) [ 18.128000] EXT4-fs (sda10): mounted filesystem with ordered data mode. Opts: (null) [ 18.204000] EXT4-fs (sda11): mounted filesystem with ordered data mode. Opts: (null) [ 18.292000] EXT4-fs (sda12): mounted filesystem with ordered data mode. Opts: (null) [ 18.372000] EXT4-fs (sda13): mounted filesystem with ordered data mode. Opts: (null) [ 18.564000] EXT4-fs (sda14): mounted filesystem with ordered data mode. Opts: (null) [ 19.620000] r8169 0000:00:06.0: eth0: link down [ 20.484000] NET: Registered protocol family 10 [ 20.492000] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 21.184000] r8169 0000:00:06.0: eth0: link up [ 21.192000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 21.300000] RPC: Registered named UNIX socket transport module. [ 21.304000] RPC: Registered udp transport module. [ 21.308000] RPC: Registered tcp transport module. [ 21.312000] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 21.360000] FS-Cache: Loaded [ 21.448000] FS-Cache: Netfs 'nfs' registered for caching [ 21.504000] Installing knfsd (copyright (C) 1996 o...@monad.swb.de). [ 27.292000] ioctl32(Xorg:1174): Unknown cmd fd(8) cmd(8004f300){t:'�';sz:4} arg(7fafcec4) on /dev/fb0 [ 27.292000] ioctl32(Xorg:1174): Unknown cmd fd(8) cmd(80046ef8){t:'n';sz:4} arg(00b5de60) on /dev/fb0 [ 27.300000] sisfb 0000:00:08.0: Invalid ROM contents [ 31.752000] eth0: no IPv6 routers present [ 35.940000] sisfb 0000:00:08.0: Invalid ROM contents [ 35.940000] sisfb 0000:00:08.0: Invalid ROM contents ** Model information system type : lemote-fuloong-2f-box cpu model : ICT Loongson-2 V0.3 FPU V0.1 ** Loaded modules: Module Size Used by cpufreq_stats 3130 0 cpufreq_conservative 6257 0 cpufreq_userspace 2128 0 cpufreq_powersave 1094 0 nfsd 359805 2 nfs 383137 0 lockd 92252 2 nfsd,nfs fscache 41569 1 nfs auth_rpcgss 48166 2 nfsd,nfs nfs_acl 2959 2 nfsd,nfs sunrpc 234434 6 nfsd,nfs,lockd,auth_rpcgss,nfs_acl ipv6 378237 26 ext4 424010 8 jbd2 76710 1 ext4 crc16 1447 1 ext4 autofs4 27460 3 fuse 80422 1 loop 18465 0 evdev 11734 5 usbhid 44648 0 hid 93455 1 usbhid snd_cs5535audio 11665 0 snd_ac97_codec 134508 1 snd_cs5535audio ac97_bus 1294 1 snd_ac97_codec snd_pcm 87605 2 snd_cs5535audio,snd_ac97_codec ohci_hcd 24339 0 snd_seq 62903 0 snd_timer 22681 2 snd_pcm,snd_seq snd_seq_device 7017 1 snd_seq snd 72623 6 snd_cs5535audio,snd_ac97_codec,snd_pcm,snd_seq,snd_timer,snd_seq_device ehci_hcd 46296 0 soundcore 6089 1 snd rtc_cmos 7696 0 usbcore 176676 4 usbhid,ohci_hcd,ehci_hcd snd_page_alloc 6989 2 snd_cs5535audio,snd_pcm loongson2_cpufreq 2827 0 loongson2_clock 2536 1 loongson2_cpufreq r8169 49164 0 mii 4787 1 r8169 ** Network interface configuration: auto lo iface lo inet loopback auto eth0 allow-hotplug eth0 iface eth0 inet static pre-up /sbin/ethtool -K eth0 rx off post-up /sbin/ethtool -K eth0 rx off address 192.168.2.120 netmask 255.255.255.0 network 192.168.2.0 broadcast 192.168.2.255 gateway 192.168.2.1 dns-nameservers 200.91.75.6 200.91.75.5 192.168.2.1 dns-search local ** Network status: *** IP interfaces and addresses: 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:23:9e:00:0f:62 brd ff:ff:ff:ff:ff:ff inet 192.168.2.120/24 brd 192.168.2.255 scope global eth0 inet6 fe80::223:9eff:fe00:f62/64 scope link valid_lft forever preferred_lft forever *** Device statistics: Inter-| Receive | Transmit face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed lo: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 eth0: 881076 1518 0 0 0 0 0 0 304557 1691 0 0 0 0 0 0 *** Protocol statistics: Ip: 1474 total packets received 0 forwarded 0 incoming packets discarded 1474 incoming packets delivered 1641 requests sent out Icmp: 0 ICMP messages received 0 input ICMP message failed. ICMP input histogram: 0 ICMP messages sent 0 ICMP messages failed ICMP output histogram: Tcp: 61 active connections openings 0 passive connection openings 0 failed connection attempts 7 connection resets received 3 connections established 1276 segments received 1438 segments send out 0 segments retransmited 0 bad segments received. 23 resets sent Udp: 186 packets received 0 packets to unknown port received. 0 packet receive errors 203 packets sent UdpLite: TcpExt: 36 TCP sockets finished time wait in fast timer 28 delayed acks sent 1 packets directly queued to recvmsg prequeue. 1 bytes directly received in process context from prequeue 839 packet headers predicted 132 acknowledgments not containing data payload received 71 predicted acknowledgments 4 connections reset due to unexpected data 7 connections reset due to early user close TCPSackShiftFallback: 1 IpExt: InMcastPkts: 12 InOctets: 857488 OutOctets: 278739 InMcastOctets: 384 *** Device features: eth0: 0x4180 lo: 0xa01b7c65 ** PCI devices: 00:06.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet [10ec:8169] (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL8169/8110 Family PCI Gigabit Ethernet NIC [10ec:8169] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 36 Region 0: I/O ports at 4000 [size=256] Region 1: Memory at 50072000 (32-bit, non-prefetchable) [size=256] Expansion ROM at 50040000 [size=128K] Capabilities: <access denied> Kernel driver in use: r8169 00:08.0 VGA compatible controller [0300]: Silicon Integrated Systems [SiS] 315PRO PCI/AGP VGA Display Adapter [1039:0325] (prog-if 00 [VGA controller]) Subsystem: Device [3030:3030] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 71 (750ns min, 4000ns max) Interrupt: pin A routed to IRQ 38 BIST result: 00 Region 0: Memory at 40000000 (32-bit, prefetchable) [size=256M] Region 1: Memory at 50000000 (32-bit, non-prefetchable) [size=256K] Region 2: I/O ports at 4800 [size=128] Expansion ROM at 50060000 [size=64K] Capabilities: <access denied> Kernel driver in use: sisfb 00:0e.0 ISA bridge [0601]: Advanced Micro Devices [AMD] CS5536 [Geode companion] ISA [1022:2090] (rev 03) Subsystem: Advanced Micro Devices [AMD] CS5536 [Geode companion] ISA [1022:2090] Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Region 0: I/O ports at 4cf0 [size=8] Region 1: I/O ports at 4400 [size=256] Region 2: I/O ports at 4c80 [size=64] Region 4: I/O ports at 4880 [size=128] Region 5: I/O ports at 4cc0 [size=32] 00:0e.2 IDE interface [0101]: Advanced Micro Devices [AMD] CS5536 [Geode companion] IDE [1022:209a] (rev 01) (prog-if 80 [Master]) Subsystem: Advanced Micro Devices [AMD] CS5536 [Geode companion] IDE [1022:209a] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (16000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 14 Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8] Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1] Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8] Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1] Region 4: I/O ports at 4ce0 [size=16] Kernel driver in use: pata_amd 00:0e.3 Multimedia audio controller [0401]: Advanced Micro Devices [AMD] CS5536 [Geode companion] Audio [1022:2093] (rev 01) Subsystem: Advanced Micro Devices [AMD] CS5536 [Geode companion] Audio [1022:2093] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (16000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 9 Region 0: I/O ports at 4c00 [size=128] Kernel driver in use: cs5535audio 00:0e.4 USB Controller [0c03]: Advanced Micro Devices [AMD] CS5536 [Geode companion] OHC [1022:2094] (rev 02) (prog-if 10 [OHCI]) Subsystem: Advanced Micro Devices [AMD] CS5536 [Geode companion] OHC [1022:2094] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (16000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 11 Region 0: Memory at 50070000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd 00:0e.5 USB Controller [0c03]: Advanced Micro Devices [AMD] CS5536 [Geode companion] EHC [1022:2095] (rev 02) (prog-if 20 [EHCI]) Subsystem: Advanced Micro Devices [AMD] CS5536 [Geode companion] EHC [1022:2095] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (16000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 11 Region 0: Memory at 50071000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ehci_hcd ** USB devices: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 04d9:1702 Holtek Semiconductor, Inc. Bus 002 Device 003: ID 0458:003a KYE Systems Corp. (Mouse Systems) NetScroll+ Mini Traveler / Genius NetScroll 120 -- System Information: Debian Release: wheezy/sid APT prefers unstable APT policy: (500, 'unstable'), (1, 'experimental') Architecture: mipsel (mips64) Kernel: Linux 3.0.0-1-loongson-2f Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash Versions of packages linux-image-3.0.0-1-loongson-2f depends on: ii debconf [debconf-2.0] 1.5.41 Debian configuration management sy ii linux-base 3.3 Linux image base package ii module-init-tools 3.16-1 tools for managing Linux kernel mo Versions of packages linux-image-3.0.0-1-loongson-2f recommends: ii firmware-linux-free 3 Binary firmware for various driver Versions of packages linux-image-3.0.0-1-loongson-2f suggests: pn linux-doc-3.0.0 <none> (no description available) Versions of packages linux-image-3.0.0-1-loongson-2f is related to: pn firmware-bnx2 <none> (no description available) pn firmware-bnx2x <none> (no description available) pn firmware-ipw2x00 <none> (no description available) pn firmware-ivtv <none> (no description available) pn firmware-iwlwifi <none> (no description available) ii firmware-linux 0.33 Binary firmware for various driver ii firmware-linux-nonfree 0.33 Binary firmware for various driver pn firmware-qlogic <none> (no description available) pn firmware-ralink <none> (no description available) pn xen-hypervisor <none> (no description available) -- debconf information: linux-image-3.0.0-1-loongson-2f/prerm/removing-running-kernel-3.0.0-1-loongson-2f: true linux-image-3.0.0-1-loongson-2f/postinst/missing-firmware-3.0.0-1-loongson-2f: linux-image-3.0.0-1-loongson-2f/postinst/depmod-error-initrd-3.0.0-1-loongson-2f: false linux-image-3.0.0-1-loongson-2f/postinst/ignoring-ramdisk: -- To UNSUBSCRIBE, email to debian-kernel-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org Archive: http://lists.debian.org/calurrgdvubgmlnftst+ks_bmbd0pt4luatq+ctv523k4zex...@mail.gmail.com
