Hello, 2011/6/11 Hector Oron <hector.o...@gmail.com>:
> 2011/6/7 Sebastian Reichel <s...@debian.org>: >> I (re)moved the armhf/config changes. Here is the new version: >> http://pkg-n900.alioth.debian.org/kernel/linux-2.6-omap-v2.patch > Patch included into patched kernel version at debian-ports.org armhf > port, so we can test it easily. I was able to test on pandaboard, here is dmesg output: [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.39-2+armhf.1-omap (Debian 2.6.39-2+armhf.1) (zu...@debian.org) (gcc version 4.5.3 (Debian 4.5.3-1) ) #1 SMP Sat Jun 11 04:02:19 UTC 2011 [ 0.000000] CPU: ARMv7 Processor [411fc092] revision 2 (ARMv7), cr=10c5387f [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: OMAP4 Panda board [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Reserving 33554432 bytes SDRAM for VRAM [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] OMAP4430 ES2.0 [ 0.000000] SRAM: Mapped pa 0x40300000 to va 0xfe400000 size: 0xe000 [ 0.000000] On node 0 totalpages: 238080 [ 0.000000] free_area_init_node: node 0, pgdat c04f2de0, node_mem_map c0567000 [ 0.000000] Normal zone: 1536 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 180736 pages, LIFO batch:31 [ 0.000000] HighMem zone: 512 pages used for memmap [ 0.000000] HighMem zone: 55296 pages, LIFO batch:15 [ 0.000000] powerdomain: waited too long for powerdomain dss_pwrdm to complete transition [ 0.000000] PERCPU: Embedded 7 pages/cpu @c0d6d000 s7648 r8192 d12832 u32768 [ 0.000000] pcpu-alloc: s7648 r8192 d12832 u32768 alloc=8*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 236032 [ 0.000000] Kernel command line: ro elevator=noop vram=32M mem=456M@0x80000000 mem=512M@0xA0000000 fixrtc quiet splash console=ttyO2,115200n8 rootdelay earlyprintk root=/dev/mmcblk0p2 [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 456MB 474MB = 930MB total [ 0.000000] Memory: 933284k/933284k available, 57948k reserved, 223232K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB) [ 0.000000] vmalloc : 0xf0800000 - 0xf8000000 ( 120 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .init : 0xc0008000 - 0xc004a000 ( 264 kB) [ 0.000000] .text : 0xc004a000 - 0xc048d620 (4366 kB) [ 0.000000] .data : 0xc048e000 - 0xc04f4418 ( 410 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled. [ 0.000000] RCU-based detection of stalled CPUs is disabled. [ 0.000000] NR_IRQS:410 [ 0.000000] omap_hwmod: dpll_mpu_m2_ck: missing clockdomain for dpll_mpu_m2_ck. [ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000244] Calibrating delay loop... 2007.19 BogoMIPS (lpj=7839744) [ 0.070312] pid_max: default: 32768 minimum: 301 [ 0.070526] Security Framework initialized [ 0.070556] SELinux: Disabled at boot. [ 0.070678] Mount-cache hash table entries: 512 [ 0.071472] Initializing cgroup subsys ns [ 0.071502] ns_cgroup deprecated: consider using the 'clone_children' flag without the ns_cgroup. [ 0.071533] Initializing cgroup subsys cpuacct [ 0.071594] Initializing cgroup subsys memory [ 0.071624] Initializing cgroup subsys devices [ 0.071624] Initializing cgroup subsys freezer [ 0.071655] Initializing cgroup subsys net_cls [ 0.071655] Initializing cgroup subsys blkio [ 0.071777] CPU: Testing write buffer coherency: ok [ 0.072082] Calibrating local timer... 491.91MHz. [ 0.117401] L310 cache controller enabled [ 0.117431] l2x0: 16 ways, CACHE_ID 0x410000c4, AUX_CTRL 0x7e470000, Cache size: 1048576 B [ 0.118530] CPU1: Booted secondary processor [ 0.118560] CPU1: Unknown IPI message 0x1 [ 0.186126] Brought up 2 CPUs [ 0.190307] SMP: Total of 2 processors activated (3972.37 BogoMIPS). [ 0.190643] devtmpfs: initialized [ 0.192535] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for emif_fw [ 0.192565] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l3_instr [ 0.192565] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l3_main_1 [ 0.192565] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l3_main_2 [ 0.192596] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_abe [ 0.192596] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_cfg [ 0.192626] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_per [ 0.192626] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_wkup [ 0.192626] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for mpu_private [ 0.192626] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for dsp [ 0.192657] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for ipu [ 0.192871] omap_hwmod: l3_div_ck: missing clockdomain for l3_div_ck. [ 0.196105] print_constraints: dummy: [ 0.196258] NET: Registered protocol family 16 [ 0.196411] GPMC revision 6.0 [ 0.197082] OMAP GPIO hardware version 0.1 [ 0.197143] OMAP GPIO hardware version 0.1 [ 0.197204] OMAP GPIO hardware version 0.1 [ 0.197265] OMAP GPIO hardware version 0.1 [ 0.197326] OMAP GPIO hardware version 0.1 [ 0.197387] OMAP GPIO hardware version 0.1 [ 0.198028] omap_mux_init: Add partition: #1: core, flags: 2 [ 0.198791] omap_mux_init: Add partition: #2: wkup, flags: 2 [ 0.201873] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers. [ 0.201873] hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step. [ 0.201904] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.202453] omap_init_sham: platform not supported [ 0.207458] omap_init_aes: platform not supported [ 0.212890] pm_dbg_init: only OMAP3 supported [ 0.217620] OMAP DMA hardware revision 0.0 [ 0.219635] bio: create slab <bio-0> at 0 [ 0.220001] print_constraints: vwl1271: 1800 mV [ 0.220520] omap_device: omap2_mcspi.4: new worst case activate latency 0: 30517 [ 0.220794] usbcore: registered new interface driver usbfs [ 0.220855] usbcore: registered new interface driver hub [ 0.220947] usbcore: registered new device driver usb [ 0.231719] omap_i2c omap_i2c.1: bus 1 rev4.0 at 400 kHz [ 0.254791] Skipping twl internal clock init and using bootloader value (unknown osc rate) [ 0.255249] twl6030: PIH (irq 39) chaining IRQs 368..387 [ 0.277648] print_constraints: VUSB: 3300 mV normal standby [ 0.497680] twl6030_usb twl6030_usb: Initialized TWL6030 USB module [ 0.497985] print_constraints: VMMC: 1200 <--> 3000 mV at 3000 mV normal standby [ 0.498413] print_constraints: VPP: 1800 <--> 2500 mV at 1900 mV normal standby [ 0.498687] print_constraints: VANA: 2100 mV normal standby [ 0.498962] print_constraints: VCXIO: 1800 mV normal standby [ 0.499267] print_constraints: VDAC: 1800 mV normal standby [ 0.499664] print_constraints: VAUX2_6030: 1200 <--> 2800 mV at 1800 mV normal standby [ 0.500061] print_constraints: VAUX3_6030: 1000 <--> 3000 mV at 1200 mV normal standby [ 0.500366] print_constraints: CLK32KG: [ 0.500518] omap_device: omap_i2c.1: new worst case deactivate latency 0: 30517 [ 0.513641] omap_i2c omap_i2c.2: bus 2 rev4.0 at 400 kHz [ 0.528869] omap_i2c omap_i2c.3: bus 3 rev4.0 at 100 kHz [ 0.544097] omap_i2c omap_i2c.4: bus 4 rev4.0 at 400 kHz [ 0.544677] Switching to clocksource 32k_counter [ 0.545257] Switched to NOHz mode on CPU #1 [ 0.551727] Switched to NOHz mode on CPU #0 [ 0.555938] musb-hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0 [ 0.556060] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) [ 0.556060] musb-hdrc: MHDRC RTL version 2.0 [ 0.556091] musb-hdrc: setup fifo_mode 4 [ 0.556091] musb-hdrc: 28/31 max ep, 16384/16384 memory [ 0.556213] musb-hdrc musb-hdrc: USB OTG mode controller at fc0ab000 using DMA, IRQ 124 [ 0.556457] omap_device: musb-omap2430.-1: new worst case deactivate latency 0: 30517 [ 0.556610] NET: Registered protocol family 2 [ 0.556854] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.557617] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.559082] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 0.559814] TCP: Hash tables configured (established 131072 bind 65536) [ 0.559814] TCP reno registered [ 0.559844] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.559936] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.560424] NET: Registered protocol family 1 [ 0.560638] Unpacking initramfs... [ 0.838043] Freeing initrd memory: 4880K [ 0.838592] omap_dsp_init: 600000 bytes @ bda00000 [ 0.839019] audit: initializing netlink socket (disabled) [ 0.839080] type=2000 audit(0.843:1): initialized [ 0.840179] highmem bounce pool size: 64 pages [ 0.840484] VFS: Disk quotas dquot_6.5.2 [ 0.840637] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.840789] msgmni has been set to 1396 [ 0.841308] alg: No test for stdrng (krng) [ 0.841430] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.841430] io scheduler noop registered (default) [ 0.841461] io scheduler deadline registered [ 0.841491] io scheduler cfq registered [ 0.904174] OMAP DSS rev 4.0 [ 1.232574] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.263671] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 104) is a OMAP UART0 [ 1.271362] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 105) is a OMAP UART1 [ 1.279174] omap_uart.2: ttyO2 at MMIO 0x48020000 (irq = 106) is a OMAP UART2 [ 1.279205] console [ttyO2] enabled, bootconsole disabled [ 1.286987] omap_uart.3: ttyO3 at MMIO 0x4806e000 (irq = 102) is a OMAP UART3 [ 1.295471] omap2-nand driver initializing [ 1.295532] OneNAND driver initializing [ 1.296020] mousedev: PS/2 mouse device common for all mice [ 1.296234] Linux media interface: v0.10 [ 1.296936] omap_device: omap_i2c.1: new worst case activate latency 0: 30517 [ 1.299163] usbcore: registered new interface driver usbhid [ 1.299163] usbhid: USB HID core driver [ 1.299865] TCP cubic registered [ 1.299896] NET: Registered protocol family 17 [ 1.299926] Registering the dns_resolver key type [ 1.299957] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 1 [ 1.300018] ThumbEE CPU extension supported. [ 1.300048] Registering SWP/SWPB emulation handler [ 1.302490] Power Management for TI OMAP4. [ 1.310974] clock: disabling unused clocks to save power [ 1.311462] registered taskstats version 1 [ 1.329254] Console: switching to colour frame buffer device 80x30 [ 1.333557] omapdss DPI: Could not find exact pixel clock. Requested 23500 kHz, got 23630 kHz [ 1.335815] regulator_init_complete: CLK32KG: incomplete constraints, leaving on [ 1.335968] regulator_init_complete: VAUX3_6030: incomplete constraints, leaving on [ 1.336120] regulator_init_complete: VAUX2_6030: incomplete constraints, leaving on [ 1.336242] regulator_init_complete: VDAC: incomplete constraints, leaving on [ 1.336395] regulator_init_complete: VCXIO: incomplete constraints, leaving on [ 1.336547] regulator_init_complete: VANA: incomplete constraints, leaving on [ 1.336700] regulator_init_complete: VPP: incomplete constraints, leaving on [ 1.336822] regulator_init_complete: VUSB: incomplete constraints, leaving on [ 1.336883] /home/zumbi/linux-2.6-2.6.39/debian/build/source_armhf_none/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 1.348937] Initializing network drop monitor service [ 1.349273] Freeing init memory: 264K [ 1.387786] mmc0: host does not support reading read-only switch. assuming write-enable. [ 1.394805] udevd[57]: starting version 168 [ 1.404235] mmc0: new high speed SDHC card at address b368 [ 1.411132] mmcblk0: mmc0:b368 LEXAR 3.73 GiB [ 1.413024] mmcblk0: p1 p2 [ 1.530731] mmc1: card claims to support voltages below the defined range. These will be ignored. [ 1.551940] mmc1: queuing unknown CIS tuple 0x91 (3 bytes) [ 1.553771] mmc1: new SDIO card at address 0001 [ 1.628417] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.628601] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller [ 1.629119] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1 [ 1.654388] ehci-omap ehci-omap.0: irq 109, io mem 0x4a064c00 [ 1.670684] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00 [ 1.670776] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.670776] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.670776] usb usb1: Product: OMAP-EHCI Host Controller [ 1.670806] usb usb1: Manufacturer: Linux 2.6.39-2+armhf.1-omap ehci_hcd [ 1.670806] usb usb1: SerialNumber: ehci-omap.0 [ 1.671295] hub 1-0:1.0: USB hub found [ 1.671325] hub 1-0:1.0: 3 ports detected [ 1.712860] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.713195] ohci-omap3 ohci-omap3.0: OMAP3 OHCI Host Controller [ 1.713470] ohci-omap3 ohci-omap3.0: new USB bus registered, assigned bus number 2 [ 1.732330] ohci-omap3 ohci-omap3.0: irq 108, io mem 0x4a064800 [ 1.814331] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 1.814331] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.814361] usb usb2: Product: OMAP3 OHCI Host Controller [ 1.814361] usb usb2: Manufacturer: Linux 2.6.39-2+armhf.1-omap ohci_hcd [ 1.814361] usb usb2: SerialNumber: ohci-omap3.0 [ 1.814819] hub 2-0:1.0: USB hub found [ 1.814819] hub 2-0:1.0: 3 ports detected [ 2.005706] usb 1-1: new high speed USB device number 2 using ehci-omap [ 2.318298] usb 1-1: New USB device found, idVendor=0424, idProduct=9514 [ 2.318328] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 2.318939] hub 1-1:1.0: USB hub found [ 2.319061] hub 1-1:1.0: 5 ports detected [ 2.880889] usb 1-1.1: new high speed USB device number 3 using ehci-omap [ 3.052825] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00 [ 3.052825] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 181.584716] device-mapper: uevent: version 1.0.3 [ 181.584960] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-de...@redhat.com [ 181.821166] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 182.368591] udevd[224]: starting version 171 [ 182.572052] Registered led device: pandaboard::status1 [ 182.572143] Registered led device: pandaboard::status2 [ 182.639709] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 [ 182.668914] omap_device: omap_wdt.-1: new worst case activate latency 0: 91552 [ 182.669525] OMAP Watchdog Timer Rev 0x00: initial timeout 60 sec [ 182.789794] cfg80211: Calling CRDA to update world regulatory domain [ 182.836120] smsc95xx v1.0.4 [ 182.941619] smsc95xx 1-1.1:1.0: eth0: register 'smsc95xx' at usb-ehci-omap.0-1.1, smsc95xx USB 2.0 Ethernet, 9a:ea:7d:53:d9:79 [ 182.941711] usbcore: registered new interface driver smsc95xx [ 183.126861] wl1271: ERROR could not get nvs file: -2 [ 183.166168] wl1271: loaded [ 183.166168] wl1271: initialized [ 183.211090] Bluetooth: Core ver 2.16 [ 183.211181] NET: Registered protocol family 31 [ 183.211181] Bluetooth: HCI device and connection manager initialized [ 183.211181] Bluetooth: HCI socket layer initialized [ 183.211212] Bluetooth: L2CAP socket layer initialized [ 183.211364] Bluetooth: SCO socket layer initialized [ 183.220367] Bluetooth: Generic Bluetooth SDIO driver ver 0.1 [ 184.049499] ------------[ cut here ]------------ [ 184.049530] WARNING: at /home/zumbi/linux-2.6-2.6.39/debian/build/source_armhf_none/kernel/irq/handle.c:130 handle_irq_event_percpu+0xf8/0x1f8() [ 184.049560] irq 379 handler twl_rtc_interrupt+0x0/0x90 [rtc_twl] enabled interrupts [ 184.049591] Modules linked in: btsdio bluetooth arc4 ecb wl12xx_sdio wl12xx mac80211 smsc95xx usbnet cfg80211 mii omap_wdt rtc_twl rfkill leds_gpio ext4 mbcache jbd2 crc16 dm_mod ohci_hcd ehci_hcd [ 184.049682] [<c005604c>] (unwind_backtrace+0x0/0xe4) from [<c0087c34>] (warn_slowpath_common+0x4c/0x64) [ 184.049713] [<c0087c34>] (warn_slowpath_common+0x4c/0x64) from [<c0087ccc>] (warn_slowpath_fmt+0x2c/0x3c) [ 184.049713] [<c0087ccc>] (warn_slowpath_fmt+0x2c/0x3c) from [<c00ce1dc>] (handle_irq_event_percpu+0xf8/0x1f8) [ 184.049743] [<c00ce1dc>] (handle_irq_event_percpu+0xf8/0x1f8) from [<c00ce31c>] (handle_irq_event+0x40/0x60) [ 184.049774] [<c00ce31c>] (handle_irq_event+0x40/0x60) from [<c00d03a4>] (handle_simple_irq+0x98/0xbc) [ 184.049804] [<c00d03a4>] (handle_simple_irq+0x98/0xbc) from [<c024c76c>] (twl6030_irq_thread+0xe0/0x154) [ 184.049835] [<c024c76c>] (twl6030_irq_thread+0xe0/0x154) from [<c00a4ae8>] (kthread+0x80/0x88) [ 184.049835] [<c00a4ae8>] (kthread+0x80/0x88) from [<c0050938>] (kernel_thread_exit+0x0/0x8) [ 184.049865] ---[ end trace 5f659a4b3123a174 ]--- [ 184.105072] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) [ 186.229675] nbd: registered device at major 43 [ 481.990051] EXT4-fs (mmcblk0p2): error count: 24 [ 481.990081] EXT4-fs (mmcblk0p2): initial error at 185: ext4_lookup:1044: inode 97 [ 481.990081] EXT4-fs (mmcblk0p2): last error at 6111225: ext4_lookup:1043: inode 97 I suspect [ 184.049530] WARNING: at /home/zumbi/linux-2.6-2.6.39/debian/build/source_armhf_none/kernel/irq/handle.c:130 handle_irq_event_percpu+0xf8/0x1f8() is due to missing TI firmware for Wilink (wlan+bluetooth+FM radio). Best regards, -- Héctor Orón -.. . -... .. .- -. -.. . ...- . .-.. --- .--. . .-. <free spam> -- Would you like to make a donation for Debian Conference? ** http://debconf11.debconf.org/payments.xhtml ** </free spam> -- To UNSUBSCRIBE, email to debian-kernel-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org Archive: http://lists.debian.org/banlktinmbyyoe1orq+cl3q1+30jbzny...@mail.gmail.com
