--- Begin Message ---
Package: linux-2.6
Version: 2.6.32-20~bpo50+1
Severity: important
There are 4 LEDs on the left side below the keyboard, 3 of which I can control
so they don't switch on or off: wifi (WLAN), caps lock, num lock. The fourth
one lights up when the battery
is being charged and is switched off when the charge is complete.
When an LED lights up or is switched off, all keyboard and touchpad input,
including the separate power button above the keyboard) becomes impossible.
Everything else is unaffected, so
the system can be shut down via ssh, bash and halt. But at the end of the
shutdown process it will not power off, the power LED at the power button
remains lit and the other LEDs stay as
they were. The computer still will not react to any input. The only way to
restart it is to remove both power sources: the mains transformer as well as
the battery. When power is resored,
the computer will boot if the power button is pressed, but the wifi (WLAN) LED
will be off even though it usually comes back on if it was on on shutdown. The
num lock and caps lock LEDs
will light up erratically a few times, then the system will boot normally. (So
it is advisable to turn the wifi LED on immediatly, so input won't be broken
again.)
It seems that the kernel's reaction to an LED state change causes the input
circuits to freeze, possibly by giving them some kind of wrong order.
There is a tendency for this to happen more markedly when someone is logged in
(gdm), but it (obviously) affects the command lines (<F1> to <F6>) as well as
they become inaccessible.
-- Package-specific info:
** Version:
Linux version 2.6.32-bpo.5-686 (Debian 2.6.32-20~bpo50+1)
(norb...@tretkowski.de) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #1 SMP Fri Aug
27 11:29:42 UTC 2010
** Command line:
root=UUID=09082eff-df48-46ee-aab2-4fa9cb52e2d8 ro
** Not tainted
** Kernel log:
[ 9.876029] sd 4:0:0:1: [sdc] Attached SCSI removable disk
[ 10.404067] cfg80211: Using static regulatory domain info
[ 10.404156] cfg80211: Regulatory domain: US
[ 10.404233] (start_freq - end_freq @ bandwidth), (max_antenna_gain,
max_eirp)
[ 10.404339] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
[ 10.404425] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 10.404512] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 10.404599] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 10.404686] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 10.404773] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
[ 10.404875] cfg80211: Calling CRDA for country: US
[ 10.485087] intel_rng: FWH not detected
[ 11.177115] input: Sleep Button as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2
[ 11.177377] ACPI: Sleep Button [SLPB]
[ 11.177667] input: Power Button as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input3
[ 11.177897] ACPI: Power Button [PWRB]
[ 11.178197] input: Lid Switch as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input4
[ 11.178541] ACPI: Lid Switch [LID]
[ 11.178831] input: Power Button as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input5
[ 11.179068] ACPI: Power Button [PWRF]
[ 11.377674] ath9k 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 11.377886] ath9k 0000:02:00.0: setting latency timer to 64
[ 11.428504] ath: EEPROM regdomain: 0x65
[ 11.428512] ath: EEPROM indicates we should expect a direct regpair map
[ 11.428524] ath: Country alpha2 being used: 00
[ 11.428530] ath: Regpair used: 0x65
[ 11.538472] ACPI: SSDT 7f7ce190 0029A (v01 PmRef Cpu0Ist 00003000 INTL
20051117)
[ 11.539822] ACPI: SSDT 7f7ce4c0 00594 (v01 PmRef Cpu0Cst 00003001 INTL
20051117)
[ 11.553113] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 19 (level, low) -> IRQ
19
[ 11.620046] Monitor-Mwait will be used to enter C-1 state
[ 11.652020] Monitor-Mwait will be used to enter C-2 state
[ 11.673157] Linux video capture interface: v2.00
[ 11.700051] Monitor-Mwait will be used to enter C-3 state
[ 11.700827] Marking TSC unstable due to TSC halts in idle
[ 11.701230] processor LNXCPU:00: registered as cooling_device0
[ 11.702331] ACPI: SSDT 7f7ce0c0 000CC (v01 PmRef Cpu1Ist 00003000 INTL
20051117)
[ 11.703223] ACPI: SSDT 7f7ce430 00085 (v01 PmRef Cpu1Cst 00003000 INTL
20051117)
[ 11.741109] Switching to clocksource hpet
[ 11.793303] processor LNXCPU:01: registered as cooling_device1
[ 11.888759] uvcvideo: Found UVC 1.00 device USB 2.0 PC Camera (18e3:9508)
[ 11.909855] input: USB 2.0 PC Camera as
/devices/pci0000:00/0000:00:1d.7/usb3/3-2/3-2:1.0/input/input6
[ 11.910113] usbcore: registered new interface driver uvcvideo
[ 11.910199] USB Video Class driver (v0.1.0)
[ 14.214470] ACPI: AC Adapter [AC] (on-line)
[ 14.239018] ACPI: Battery Slot [BAT1] (battery present)
[ 14.424673] input: Video Bus as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input7
[ 14.424919] ACPI: Video Device [IGD] (multi-head: yes rom: no post: no)
[ 17.260577] ACPI: WMI: Mapper loaded
[ 19.210041] input: PS/2 Mouse as /devices/platform/i8042/serio2/input/input8
[ 19.231338] input: AlpsPS/2 ALPS GlidePoint as
/devices/platform/i8042/serio2/input/input9
[ 20.020342] phy0: Selected rate control algorithm 'ath9k_rate_control'
[ 20.022329] Registered led device: ath9k-phy0::radio
[ 20.023622] Registered led device: ath9k-phy0::assoc
[ 20.023761] Registered led device: ath9k-phy0::tx
[ 20.023898] Registered led device: ath9k-phy0::rx
[ 20.024319] phy0: Atheros AR9285 MAC/BB Rev:2 AR5133 RF Rev:e0:
mem=0xf81a0000, irq=17
[ 20.043151] udev: renamed network interface wlan0 to wlan1
[ 20.180118] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ
16
[ 20.180367] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 20.585462] hda_codec: ALC269: BIOS auto-probing.
[ 20.586138] input: HDA Digital PCBeep as
/devices/pci0000:00/0000:00:1b.0/input/input10
[ 22.174383] Adding 7992k swap on /dev/sda7. Priority:-1 extents:1
across:7992k
[ 22.498984] EXT3 FS on sda1, internal journal
[ 23.292500] loop: module loaded
[ 25.233535] kjournald starting. Commit interval 5 seconds
[ 25.234512] EXT3 FS on sda9, internal journal
[ 25.234660] EXT3-fs: mounted filesystem with ordered data mode.
[ 25.248691] kjournald starting. Commit interval 5 seconds
[ 25.249207] EXT3 FS on sda8, internal journal
[ 25.249333] EXT3-fs: mounted filesystem with ordered data mode.
[ 25.279732] kjournald starting. Commit interval 5 seconds
[ 25.280297] EXT3 FS on sda5, internal journal
[ 25.280445] EXT3-fs: mounted filesystem with ordered data mode.
[ 25.311300] kjournald starting. Commit interval 5 seconds
[ 25.312350] EXT3 FS on sda6, internal journal
[ 25.312496] EXT3-fs: mounted filesystem with ordered data mode.
[ 27.361071] r8169: eth0: link up
[ 27.361160] r8169: eth0: link up
[ 30.681754] r8169: WARNING! Changing of MTU on this NIC may lead to frame
reception errors!
[ 33.485732] lp: driver loaded but no devices found
[ 33.622998] ppdev: user-space parallel port driver
[ 34.197241] tun: Universal TUN/TAP device driver, 1.6
[ 34.197334] tun: (C) 1999-2004 Max Krasnyansky <m...@qualcomm.com>
[ 34.199108] tun0: Disabled Privacy Extensions
[ 37.363177] ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 37.952053] eth0: no IPv6 routers present
[ 39.511090] Bluetooth: Core ver 2.15
[ 39.511342] NET: Registered protocol family 31
[ 39.511437] Bluetooth: HCI device and connection manager initialized
[ 39.511525] Bluetooth: HCI socket layer initialized
[ 39.640899] Bluetooth: L2CAP ver 2.14
[ 39.640988] Bluetooth: L2CAP socket layer initialized
[ 39.655504] Bluetooth: RFCOMM TTY layer initialized
[ 39.655602] Bluetooth: RFCOMM socket layer initialized
[ 39.655689] Bluetooth: RFCOMM ver 1.11
[ 44.941431] [drm] Initialized drm 1.1.0 20060810
[ 45.043222] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 45.043237] pci 0000:00:02.0: setting latency timer to 64
[ 45.054411] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 2809.000055] NOHZ: local_softirq_pending 100
** Model information
not available
** Loaded modules:
Module Size Used by
i915 221479 2
drm_kms_helper 18317 1 i915
drm 112040 4 i915,drm_kms_helper
i2c_algo_bit 3497 1 i915
rfcomm 25191 0
l2cap 21705 5 rfcomm
crc16 1027 1 l2cap
bluetooth 36343 4 rfcomm,l2cap
tun 8768 2
ppdev 4058 0
parport_pc 15799 0
lp 5570 0
parport 22550 3 ppdev,parport_pc,lp
acpi_cpufreq 4947 0
cpufreq_powersave 602 0
cpufreq_conservative 4018 0
cpufreq_userspace 1488 0
cpufreq_stats 1940 0
loop 9765 0
snd_hda_codec_realtek 163258 1
snd_hda_intel 16795 0
snd_hda_codec 46002 2 snd_hda_codec_realtek,snd_hda_intel
snd_hwdep 4054 1 snd_hda_codec
snd_pcm_oss 28679 0
snd_mixer_oss 10461 1 snd_pcm_oss
snd_pcm 47186 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss
arc4 974 2
joydev 6751 0
ecb 1405 2
snd_seq_midi 3576 0
snd_rawmidi 12509 1 snd_seq_midi
wmi 3575 0
snd_seq_midi_event 3684 1 snd_seq_midi
snd_seq 35491 2 snd_seq_midi,snd_seq_midi_event
snd_timer 12238 2 snd_pcm,snd_seq
snd_seq_device 3673 3 snd_seq_midi,snd_rawmidi,snd_seq
video 14621 1 i915
output 1204 1 video
battery 3782 0
ac 1640 0
snd 34383 11
snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
uvcvideo 45370 0
videodev 25569 1 uvcvideo
v4l1_compat 10250 2 uvcvideo,videodev
i2c_i801 6462 0
processor 26631 3 acpi_cpufreq
ath9k 238445 0
button 3598 1 i915
soundcore 3450 1 snd
i2c_core 12700 6
i915,drm_kms_helper,drm,i2c_algo_bit,videodev,i2c_i801
serio_raw 2920 0
evdev 5609 8
mac80211 123422 1 ath9k
ath 6022 1 ath9k
psmouse 44669 0
snd_page_alloc 5065 2 snd_hda_intel,snd_pcm
rng_core 2178 0
cfg80211 87805 3 ath9k,mac80211,ath
rfkill 10280 2 bluetooth,cfg80211
led_class 1757 1 ath9k
pcspkr 1207 0
ext3 94316 5
jbd 32213 1 ext3
mbcache 3766 1 ext3
usb_storage 30481 0
sd_mod 25889 7
crc_t10dif 1012 1 sd_mod
ata_piix 17616 6
ata_generic 2019 0
libata 115757 2 ata_piix,ata_generic
ehci_hcd 27927 0
uhci_hcd 16069 0
scsi_mod 101453 3 usb_storage,sd_mod,libata
r8169 24796 0
mii 2714 1 r8169
usbcore 98450 5 uvcvideo,usb_storage,ehci_hcd,uhci_hcd
nls_base 4541 1 usbcore
thermal 9198 0
fan 2590 0
thermal_sys 9378 4 video,processor,thermal,fan
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
allow-hotplug eth0
iface eth0 inet dhcp
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1320 qdisc pfifo_fast state
UNKNOWN qlen 1000
link/ether 90:fb:a6:29:8b:4d brd ff:ff:ff:ff:ff:ff
inet 192.168.1.13/24 brd 192.168.1.255 scope global eth0
inet6 fe80::92fb:a6ff:fe29:8b4d/64 scope link
valid_lft forever preferred_lft forever
3: wlan1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN qlen
1000
link/ether 0c:ee:e6:90:d6:2c brd ff:ff:ff:ff:ff:ff
4: tun0: <POINTOPOINT,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
state UNKNOWN qlen 100
link/[65534]
inet 10.4.0.22 peer 10.4.0.21/32 scope global tun0
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes
packets errs drop fifo colls carrier compressed
lo: 560 8 0 0 0 0 0 0 560
8 0 0 0 0 0 0
eth0: 1158102 4015 0 0 0 0 0 0 617211
4524 0 0 0 0 0 0
wlan1: 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0
tun0: 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0
*** Protocol statistics:
Ip:
3873 total packets received
0 forwarded
0 incoming packets discarded
3873 incoming packets delivered
4361 requests sent out
Icmp:
0 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
0 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
Tcp:
14 active connections openings
2 passive connection openings
0 failed connection attempts
2 connection resets received
1 connections established
1210 segments received
871 segments send out
0 segments retransmited
0 bad segments received.
4 resets sent
Udp:
2663 packets received
0 packets to unknown port received.
0 packet receive errors
3488 packets sent
UdpLite:
TcpExt:
7 TCP sockets finished time wait in fast timer
18 delayed acks sent
1 delayed acks further delayed because of locked socket
141 packets directly queued to recvmsg prequeue.
143596 bytes directly received in process context from prequeue
480 packet headers predicted
88 packets header predicted and directly queued to user
95 acknowledgments not containing data payload received
311 predicted acknowledgments
2 connections reset due to early user close
IpExt:
InMcastPkts: 21
OutMcastPkts: 19
InBcastPkts: 2
InOctets: 1097611
OutOctets: 546414
InMcastOctets: 3155
OutMcastOctets: 2921
InBcastOctets: 656
*** Device features:
eth0: 0x180
lo: 0x13865
tun0: 0x0
wlan1: 0x2000
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GME Express Memory
Controller Hub [8086:27ac] (rev 03)
Subsystem: Foxconn International, Inc. Device [105b:0d4f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 945GME
Express Integrated Graphics Controller [8086:27ae] (rev 03) (prog-if 00 [VGA
controller])
Subsystem: Foxconn International, Inc. Device [105b:0d4f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe980000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at dc80 [size=8]
Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at fe940000 (32-bit, non-prefetchable) [size=256K]
Capabilities: <access denied>
Kernel modules: i915
00:02.1 Display controller [0380]: Intel Corporation Mobile 945GM/GMS/GME,
943/940GML Express Integrated Graphics Controller [8086:27a6] (rev 03)
Subsystem: Foxconn International, Inc. Device [105b:0d4f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at fe880000 (32-bit, non-prefetchable) [size=512K]
Capabilities: <access denied>
00:1b.0 Audio device [0403]: Intel Corporation 82801G (ICH7 Family) High
Definition Audio Controller [8086:27d8] (rev 02)
Subsystem: Foxconn International, Inc. Device [105b:0d4f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe938000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express
Port 1 [8086:27d0] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: 80000000-801fffff
Prefetchable memory behind bridge: 0000000080200000-00000000803fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.1 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express
Port 2 [8086:27d2] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: fea00000-feafffff
Prefetchable memory behind bridge: 0000000080400000-00000000805fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.2 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express
Port 3 [8086:27d4] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: feb00000-febfffff
Prefetchable memory behind bridge: 00000000fdf00000-00000000fdffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1d.0 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #1 [8086:27c8] (rev 02) (prog-if 00 [UHCI])
Subsystem: Foxconn International, Inc. Device [105b:0d4f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at dc00 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #2 [8086:27c9] (rev 02) (prog-if 00 [UHCI])
Subsystem: Foxconn International, Inc. Device [105b:0d4f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at d880 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #3 [8086:27ca] (rev 02) (prog-if 00 [UHCI])
Subsystem: Foxconn International, Inc. Device [105b:0d4f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at d800 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.3 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #4 [8086:27cb] (rev 02) (prog-if 00 [UHCI])
Subsystem: Foxconn International, Inc. Device [105b:0d4f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at d480 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB2 EHCI
Controller [8086:27cc] (rev 02) (prog-if 20 [EHCI])
Subsystem: Foxconn International, Inc. Device [105b:0d4f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fe937c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge
[8086:2448] (rev e2) (prog-if 01 [Subtractive decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC Interface
Bridge [8086:27b9] (rev 02)
Subsystem: Foxconn International, Inc. Device [105b:0d4f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel modules: iTCO_wdt, intel-rng
00:1f.1 IDE interface [0101]: Intel Corporation 82801G (ICH7 Family) IDE
Controller [8086:27df] (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Foxconn International, Inc. Device [105b:0d4f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at ffa0 [size=16]
Kernel driver in use: ata_piix
Kernel modules: ata_piix
00:1f.2 IDE interface [0101]: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA
IDE Controller [8086:27c4] (rev 02) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Foxconn International, Inc. Device [105b:0d4f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at d400 [size=8]
Region 1: I/O ports at d080 [size=4]
Region 2: I/O ports at d000 [size=8]
Region 3: I/O ports at cc80 [size=4]
Region 4: I/O ports at cc00 [size=16]
Region 5: Memory at fe937800 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ata_piix
Kernel modules: ata_piix
00:1f.3 SMBus [0c05]: Intel Corporation 82801G (ICH7 Family) SMBus Controller
[8086:27da] (rev 02)
Subsystem: Foxconn International, Inc. Device [105b:0d4f]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 0400 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
02:00.0 Network controller [0280]: Atheros Communications Inc. Device
[168c:002b] (rev 01)
Subsystem: Foxconn International, Inc. Device [105b:e023]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at feaf0000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: ath9k
Kernel modules: ath9k
03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 02)
Subsystem: Foxconn International, Inc. Device [105b:0cd6]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 27
Region 0: I/O ports at ec00 [size=256]
Region 2: Memory at febff000 (64-bit, non-prefetchable) [size=4K]
Region 4: Memory at fdff0000 (64-bit, prefetchable) [size=64K]
Expansion ROM at febc0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: r8169
Kernel modules: r8169
** USB devices:
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 003: ID 0bda:0156 Realtek Semiconductor Corp. Mass Storage Device
Bus 003 Device 002: ID 18e3:9508 Fitipower Integrated Technology Inc
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
-- System Information:
Debian Release: 5.0.6
APT prefers stable
APT policy: (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 2.6.32-bpo.5-686 (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8) (ignored: LC_ALL
set to en_US.utf8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.32-bpo.5-686 depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy
ii initramfs-tools [linux 0.92o tools for generating an initramfs
ii linux-base 2.6.32-20~bpo50+1 Linux image base package
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.32-bpo.5-686 recommends:
ii firmware-linux-free 2.6.32-15~bpo50+1 Binary firmware for various driver
ii libc6-i686 2.7-18lenny4 GNU C Library: Shared libraries [i
Versions of packages linux-image-2.6.32-bpo.5-686 suggests:
ii grub 0.97-47lenny2 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.32 <none> (no description available)
Versions of packages linux-image-2.6.32-bpo.5-686 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
ii firmware-linux 0.24~bpo50+1 Binary firmware for various driver
ii firmware-linux-nonfree 0.24~bpo50+1 Binary firmware for various driver
pn firmware-qlogic <none> (no description available)
ii firmware-ralink 0.24~bpo50+1 Binary firmware for Ralink RT2561,
pn xen-hypervisor <none> (no description available)
-- debconf information:
linux-image-2.6.32-bpo.5-686/postinst/depmod-error-initrd-2.6.32-bpo.5-686:
false
linux-image-2.6.32-bpo.5-686/postinst/ignoring-do-bootloader-2.6.32-bpo.5-686:
linux-image-2.6.32-bpo.5-686/prerm/removing-running-kernel-2.6.32-bpo.5-686:
true
linux-image-2.6.32-bpo.5-686/postinst/missing-firmware-2.6.32-bpo.5-686:
--- End Message ---
signature.asc
