Package: linux-2.6
Version: 2.6.32-30
Severity: normal
I'm having an issue with my usb 3.0 port. I've recently bought an Asus N73JF
laptop which has one such port. I'm running a fully updated Wheezy with the
2.6.32-5-amd64 kernel image from the Debian repo. When booting and later on
during the entire session I get lots of "hub 1-1:1.0: unable to enumerate USB
device on port 5" messages (check the kernel log!). The usb 3.0 port doesn't
work at all, other usb (2.0) ports work normally. When I connect something to
the 3.0 port, e.g. a flash drive and then run "dmesg", the flood of the
aforementioned messages is suppressed for a while and the following can be
seen, concerning the usb event:
#dmesg
(...)
[ 3164.208462] usb 3-2: new high speed USB device using xhci_hcd and address 0
[ 3184.182608] xhci_hcd 0000:04:00.0: Timeout while waiting for a slot
[ 3204.360596] xhci_hcd 0000:04:00.0: Timeout while waiting for a slot
[ 3204.564388] usb 3-2: device not accepting address 0, error -62
[ 3204.564403] hub 3-0:1.0: cannot disable port 2 (err = -32)
[ 3212.857492] Inbound IN=wlan0 OUT=
MAC=01:00:5e:7f:ff:fa:00:22:43:4c:ac:cb:08:00 SRC=192.168.1.101
DST=239.255.255.250 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=62022 PROTO=2
[ 3224.538660] xhci_hcd 0000:04:00.0: Timeout while waiting for a slot
[ 3224.538668] hub 3-0:1.0: couldn't allocate port 2 usb_device
[ 3224.538682] hub 3-0:1.0: cannot disable port 2 (err = -32)
(...)
When I run "lspci -v" I get the following (among others, for the whole output
of lspci see below):
04:00.0 USB Controller: Fresco Logic Device 1400 (rev 01) (prog-if 30)
Subsystem: Device 1d5c:1000
Flags: bus master, fast devsel, latency 0, IRQ 19
Memory at d6000000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 3
Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [80] Express Endpoint, MSI 00
Kernel driver in use: xhci_hcd
As expected, xhci_hcd is in use for the 3.0 port. Nonetheless I double-checked
it:
#lsmod | grep xhci*
xhci 33037 0
usbcore 122034 6 usb_storage,ehci_hcd,xhci,uvcvideo,usbhid
It appears that there is no such thing as xhci_hcd, at least not loaded. So I
tried to load it:
#modprobe xhci_hcd
FATAL: Module xhci_hcd not found.
I looked into /sys/bus/pci/drivers/ and xhci_hcd is there all right. Now I'm
really perplexed...
I googled a little and found something about the possibility of ehci_hcd
getting in the way, so I tried disabling it. After I ran "modprobe -r ehci_hcd"
I lost all the usb ports (not really unexpected) but the 3.0 port didn't work
any better. But the good thing was that the annoying "unable to enumerate USB
device on port 5" messages immediately stopped polluting my logs. So it's
ehci_hcd that's generating all that noise. I doubt that he's responsible for
the 3.0 port malfunctioning though (but I may be mistaken). These messages are
really problematic. Recently I was trying to install the nvidia driver and
afterwards my X didn't wake up. I was in the need of working from the console
and these kernel messages were flashing onto the screen every second so I
couldn't even edit xorg.conf. Fortunately I remembered it was ehci's fault, so
I disabled it. It shouldn't work that way though.
I was advised at linux.debian.user to send a bug report against the kernel.
Since I'm using this one I'm reporting the bug for this package. Nonetheless it
may be a more general issue. I didn't check it with any other kernel so I can't
know that.
Thanks for your time,
KB
-- Package-specific info:
** Version:
Linux version 2.6.32-5-amd64 (Debian 2.6.32-30) (b...@decadent.org.uk) (gcc
version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Wed Jan 12 03:40:32 UTC 2011
** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-amd64
root=UUID=cc39a16b-55e4-4279-98e8-eb5c35251fdc ro quiet
** Tainted: PW (513)
* Proprietary module has been loaded.
* Taint on warning.
** Kernel log:
[ 2777.178268] usb 1-1.5: new full speed USB device using ehci_hcd and address
43
[ 2777.194245] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2777.526027] usb 1-1.5: new full speed USB device using ehci_hcd and address
44
[ 2777.542195] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2777.940989] usb 1-1.5: new full speed USB device using ehci_hcd and address
45
[ 2777.957559] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2778.292506] usb 1-1.5: new full speed USB device using ehci_hcd and address
46
[ 2778.308767] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2778.708595] usb 1-1.5: new full speed USB device using ehci_hcd and address
47
[ 2778.724731] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2779.059567] usb 1-1.5: new full speed USB device using ehci_hcd and address
48
[ 2779.075665] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2779.474879] usb 1-1.5: new full speed USB device using ehci_hcd and address
49
[ 2779.491408] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2779.822495] usb 1-1.5: new full speed USB device using ehci_hcd and address
50
[ 2779.842948] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2780.241908] usb 1-1.5: new full speed USB device using ehci_hcd and address
51
[ 2780.258870] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2780.621482] usb 1-1.5: new full speed USB device using ehci_hcd and address
52
[ 2780.637724] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2781.005129] usb 1-1.5: new full speed USB device using ehci_hcd and address
53
[ 2781.021066] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2781.392589] usb 1-1.5: new full speed USB device using ehci_hcd and address
54
[ 2781.408793] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2781.772650] usb 1-1.5: new full speed USB device using ehci_hcd and address
55
[ 2781.788499] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2782.156035] usb 1-1.5: new full speed USB device using ehci_hcd and address
56
[ 2782.171820] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2782.539103] usb 1-1.5: new full speed USB device using ehci_hcd and address
57
[ 2782.555150] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2782.922320] usb 1-1.5: new full speed USB device using ehci_hcd and address
58
[ 2782.938724] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2783.306007] usb 1-1.5: new full speed USB device using ehci_hcd and address
59
[ 2783.322511] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2783.689421] usb 1-1.5: new full speed USB device using ehci_hcd and address
60
[ 2783.706254] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2784.073538] usb 1-1.5: new full speed USB device using ehci_hcd and address
61
[ 2784.089197] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2784.456249] usb 1-1.5: new full speed USB device using ehci_hcd and address
62
[ 2784.472956] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2784.840305] usb 1-1.5: new full speed USB device using ehci_hcd and address
63
[ 2784.855911] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2785.224025] usb 1-1.5: new full speed USB device using ehci_hcd and address
64
[ 2785.244223] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2785.606715] usb 1-1.5: new full speed USB device using ehci_hcd and address
65
[ 2785.626999] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2785.990882] usb 1-1.5: new full speed USB device using ehci_hcd and address
66
[ 2786.015244] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2786.377849] usb 1-1.5: new full speed USB device using ehci_hcd and address
67
[ 2786.402562] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2794.499429] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2794.874202] usb 1-1.5: new full speed USB device using ehci_hcd and address
69
[ 2794.891129] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2795.266515] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2795.641305] usb 1-1.5: new full speed USB device using ehci_hcd and address
71
[ 2795.657959] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2796.032866] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2796.416073] usb 1-1.5: new full speed USB device using ehci_hcd and address
73
[ 2796.432430] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2796.804440] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2797.175397] usb 1-1.5: new full speed USB device using ehci_hcd and address
75
[ 2797.199358] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2797.622478] usb 1-1.5: new full speed USB device using ehci_hcd and address
76
[ 2797.638739] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2797.974222] usb 1-1.5: new full speed USB device using ehci_hcd and address
77
[ 2797.990993] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2798.393808] usb 1-1.5: new full speed USB device using ehci_hcd and address
78
[ 2798.410885] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2798.741549] usb 1-1.5: new full speed USB device using ehci_hcd and address
79
[ 2798.757971] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2799.156409] usb 1-1.5: new full speed USB device using ehci_hcd and address
80
[ 2799.172629] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2799.508157] usb 1-1.5: new full speed USB device using ehci_hcd and address
81
[ 2799.524881] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2799.923955] usb 1-1.5: new full speed USB device using ehci_hcd and address
82
[ 2799.939905] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2800.279179] usb 1-1.5: new full speed USB device using ehci_hcd and address
83
[ 2800.299141] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2800.694903] usb 1-1.5: new full speed USB device using ehci_hcd and address
84
[ 2800.711460] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2801.042065] usb 1-1.5: new full speed USB device using ehci_hcd and address
85
[ 2801.058345] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2801.457690] usb 1-1.5: new full speed USB device using ehci_hcd and address
86
[ 2801.473877] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2801.808891] usb 1-1.5: new full speed USB device using ehci_hcd and address
87
[ 2801.825383] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2802.224816] usb 1-1.5: new full speed USB device using ehci_hcd and address
88
[ 2802.240625] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2802.576018] usb 1-1.5: new full speed USB device using ehci_hcd and address
89
[ 2802.600064] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2802.991392] usb 1-1.5: new full speed USB device using ehci_hcd and address
90
[ 2803.007515] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2803.375090] usb 1-1.5: new full speed USB device using ehci_hcd and address
91
[ 2803.391278] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2803.758948] usb 1-1.5: new full speed USB device using ehci_hcd and address
92
[ 2803.774918] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2804.142237] usb 1-1.5: new full speed USB device using ehci_hcd and address
93
[ 2804.157874] hub 1-1:1.0: unable to enumerate USB device on port 5
[ 2804.525523] usb 1-1.5: new full speed USB device using ehci_hcd and address
94
[ 2804.541698] hub 1-1:1.0: unable to enumerate USB device on port 5
** Model information
sys_vendor: ASUSTeK Computer Inc.
product_name: N73JF
product_version: 1.0
chassis_vendor: ASUSTeK Computer Inc.
chassis_version: 1.0
bios_vendor: American Megatrends Inc.
bios_version: N73JF.203
board_vendor: ASUSTeK Computer Inc.
board_name: N73JF
board_version: 1.0
** Loaded modules:
Module Size Used by
xt_limit 1782 8
xt_tcpudp 2319 16
ipt_LOG 4518 8
ipt_MASQUERADE 1554 0
xt_DSCP 1995 0
ipt_REJECT 1953 1
nf_conntrack_irc 3347 0
nf_conntrack_ftp 5537 0
xt_state 1303 6
aes_x86_64 7340 1
aes_generic 25714 1 aes_x86_64
parport_pc 18855 0
ppdev 5030 0
lp 7462 0
parport 27954 3 parport_pc,ppdev,lp
binfmt_misc 6431 1
uinput 6376 1
iptable_nat 4299 0
nf_nat 13388 2 ipt_MASQUERADE,iptable_nat
nf_conntrack_ipv4 9833 9 iptable_nat,nf_nat
nf_conntrack 46535 7
ipt_MASQUERADE,nf_conntrack_irc,nf_conntrack_ftp,xt_state,iptable_nat,nf_nat,nf_conntrack_ipv4
nf_defrag_ipv4 1139 1 nf_conntrack_ipv4
iptable_mangle 2817 0
iptable_filter 2258 1
ip_tables 13899 3 iptable_nat,iptable_mangle,iptable_filter
x_tables 12845 9
xt_limit,xt_tcpudp,ipt_LOG,ipt_MASQUERADE,xt_DSCP,ipt_REJECT,xt_state,iptable_nat,ip_tables
loop 11799 0
snd_hda_codec_realtek 235602 1
snd_hda_intel 20019 1
snd_hda_codec 54244 2 snd_hda_codec_realtek,snd_hda_intel
snd_hwdep 5380 1 snd_hda_codec
arc4 1274 2
ecb 1841 2
uvcvideo 52063 0
i915 255262 2
snd_pcm 60503 2 snd_hda_intel,snd_hda_codec
snd_seq 42881 0
snd_timer 15582 2 snd_pcm,snd_seq
snd_seq_device 4493 1 snd_seq
videodev 29993 1 uvcvideo
joydev 8459 0
drm_kms_helper 20065 1 i915
ath9k 249912 0
mac80211 137340 1 ath9k
v4l1_compat 11442 2 uvcvideo,videodev
snd 46446 10
snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_seq,snd_timer,snd_seq_device
ath 8006 1 ath9k
drm 142359 3 i915,drm_kms_helper
soundcore 4598 1 snd
v4l2_compat_ioctl32 8474 1 videodev
usbhid 33292 0
nvidia 10670090 0
snd_page_alloc 6249 2 snd_hda_intel,snd_pcm
cfg80211 101496 3 ath9k,mac80211,ath
i2c_algo_bit 4225 1 i915
hid 63225 1 usbhid
asus_laptop 13930 0
rfkill 13044 1 cfg80211
psmouse 49777 0
video 17445 1 i915
i2c_core 15712 6
i915,videodev,drm_kms_helper,drm,nvidia,i2c_algo_bit
wmi 4323 0
evdev 7352 34
serio_raw 3752 0
pcspkr 1699 0
button 4650 1 i915
led_class 2433 2 ath9k,asus_laptop
battery 4998 0
output 1692 1 video
ac 2192 0
processor 29935 4
ext3 106518 5
jbd 37085 1 ext3
mbcache 5050 1 ext3
sg 18744 0
sr_mod 12602 0
cdrom 29415 1 sr_mod
sd_mod 29889 7
crc_t10dif 1276 1 sd_mod
xhci 33037 0
ahci 32374 6
ehci_hcd 31151 0
libata 133632 1 ahci
thermal 11674 0
thermal_sys 11942 3 video,processor,thermal
scsi_mod 122149 4 sg,sr_mod,sd_mod,libata
atl1c 27347 0
usbcore 122034 5 uvcvideo,usbhid,xhci,ehci_hcd
nls_base 6377 1 usbcore
** Network interface configuration:
auto lo
iface lo inet loopback
iface eth0 inet dhcp
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
link/ether 48:5b:39:98:f5:e5 brd ff:ff:ff:ff:ff:ff
3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
link/ether 74:f0:6d:34:82:5f brd ff:ff:ff:ff:ff:ff
inet 192.168.1.103/24 brd 192.168.1.255 scope global wlan0
inet6 fe80::76f0:6dff:fe34:825f/64 scope link
valid_lft forever preferred_lft forever
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes
packets errs drop fifo colls carrier compressed
lo: 100796 1094 0 0 0 0 0 0 100796
1094 0 0 0 0 0 0
eth0: 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0
wlan0:77213019 181432 0 0 0 0 0 0 203186059
392614 0 0 0 0 0 0
*** Protocol statistics:
Ip:
182526 total packets received
1 with invalid addresses
0 forwarded
0 incoming packets discarded
182168 incoming packets delivered
392267 requests sent out
1278 outgoing packets dropped
22 dropped because of missing route
34 reassemblies required
17 packets reassembled ok
535 fragments received ok
1070 fragments created
Icmp:
1526 ICMP messages received
1240 input ICMP message failed.
ICMP input histogram:
destination unreachable: 1526
339 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
destination unreachable: 339
IcmpMsg:
InType3: 1526
OutType3: 339
Tcp:
12045 active connections openings
50 passive connection openings
1235 failed connection attempts
75 connection resets received
54 connections established
137210 segments received
175580 segments send out
13881 segments retransmited
0 bad segments received.
661 resets sent
Udp:
43089 packets received
339 packets to unknown port received.
0 packet receive errors
202509 packets sent
SndbufErrors: 328
UdpLite:
TcpExt:
278 TCP sockets finished time wait in fast timer
57 time wait sockets recycled by time stamp
2646 delayed acks sent
1 delayed acks further delayed because of locked socket
Quick ack mode was activated 537 times
37558 packet headers predicted
28946 acknowledgments not containing data payload received
43031 predicted acknowledgments
370 times recovered from packet loss due to fast retransmit
4 congestion windows recovered without slow start by DSACK
205 congestion windows recovered without slow start after partial ack
367 timeouts after reno fast retransmit
241 timeouts in loss state
475 fast retransmits
1422 retransmits in slow start
9138 other TCP timeouts
170 classic Reno fast retransmits failed
4 DSACKs sent for old packets
9 DSACKs received
103 connections reset due to unexpected data
8 connections reset due to early user close
600 connections aborted due to timeout
TCPDSACKIgnoredOld: 2
TCPSpuriousRTOs: 11
IpExt:
InMcastPkts: 56
OutMcastPkts: 13
InBcastPkts: 56
InOctets: 74775649
OutOctets: 190575635
InMcastOctets: 3780
OutMcastOctets: 2404
InBcastOctets: 6185
*** Device features:
eth0: 0x110989
lo: 0x13865
wlan0: 0x2000
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Core Processor DRAM Controller
[8086:0044] (rev 18)
Subsystem: ASUSTeK Computer Inc. Device [1043:1f17]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:01.0 PCI bridge [0604]: Intel Corporation Core Processor PCI Express x16
Root Port [8086:0045] (rev 18) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: c0000000-d30fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:02.0 VGA compatible controller [0300]: Intel Corporation Core Processor
Integrated Graphics Controller [8086:0046] (rev 18) (prog-if 00 [VGA
controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:1512]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 36
Region 0: Memory at d3400000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at b0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at e080 [size=8]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:16.0 Communication controller [0780]: Intel Corporation 5 Series/3400 Series
Chipset HECI Controller [8086:3b64] (rev 06)
Subsystem: ASUSTeK Computer Inc. Device [1043:1f17]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d9c0a000 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
00:1a.0 USB Controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset
USB2 Enhanced Host Controller [8086:3b3c] (rev 06) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:1f17]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d9c08000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1b.0 Audio device [0403]: Intel Corporation 5 Series/3400 Series Chipset
High Definition Audio [8086:3b56] (rev 06)
Subsystem: ASUSTeK Computer Inc. Device [1043:10a3]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at d9c00000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
00:1c.0 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series Chipset PCI
Express Root Port 1 [8086:3b42] (rev 06) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: d8800000-d9bfffff
Prefetchable memory behind bridge: 00000000d3100000-00000000d32fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.1 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series Chipset PCI
Express Root Port 2 [8086:3b44] (rev 06) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: d7400000-d87fffff
Prefetchable memory behind bridge: 00000000d9d00000-00000000d9efffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.3 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series Chipset PCI
Express Root Port 4 [8086:3b48] (rev 06) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: d6000000-d73fffff
Prefetchable memory behind bridge: 00000000d9f00000-00000000da0fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.4 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series Chipset PCI
Express Root Port 5 [8086:3b4a] (rev 06) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: d4c00000-d5ffffff
Prefetchable memory behind bridge: 00000000da100000-00000000da2fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.5 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series Chipset PCI
Express Root Port 6 [8086:3b4c] (rev 06) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
I/O behind bridge: 00008000-00008fff
Memory behind bridge: d3800000-d4bfffff
Prefetchable memory behind bridge: 00000000da300000-00000000da4fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB Controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset
USB2 Enhanced Host Controller [8086:3b34] (rev 06) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:1f17]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at d9c07000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge
[8086:2448] (rev a6) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=07, subordinate=07, sec-latency=32
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation Mobile 5 Series Chipset LPC
Interface Controller [8086:3b09] (rev 06)
Subsystem: ASUSTeK Computer Inc. Device [1043:1f17]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 SATA controller [0106]: Intel Corporation 5 Series/3400 Series Chipset
4 port SATA AHCI Controller [8086:3b29] (rev 06) (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Device [1043:1f17]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 35
Region 0: I/O ports at e070 [size=8]
Region 1: I/O ports at e060 [size=4]
Region 2: I/O ports at e050 [size=8]
Region 3: I/O ports at e040 [size=4]
Region 4: I/O ports at e020 [size=32]
Region 5: Memory at d9c06000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.6 Signal processing controller [1180]: Intel Corporation 5 Series/3400
Series Chipset Thermal Subsystem [8086:3b32] (rev 06)
Subsystem: ASUSTeK Computer Inc. Device [1043:1f17]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 10
Region 0: Memory at d9c04000 (64-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
01:00.0 VGA compatible controller [0300]: nVidia Corporation Device [10de:0df0]
(rev a1) (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:1512]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d2000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at d0000000 (64-bit, prefetchable) [size=32M]
Region 5: I/O ports at d000 [size=128]
Expansion ROM at d3000000 [disabled] [size=512K]
Capabilities: <access denied>
Kernel driver in use: nvidia
03:00.0 Network controller [0280]: Atheros Communications Inc. AR9285 Wireless
Network Adapter (PCI-Express) [168c:002b] (rev 01)
Subsystem: AzureWave Device [1a3b:1089]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at d7400000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: ath9k
04:00.0 USB Controller [0c03]: Fresco Logic Device [1b73:1400] (rev 01)
(prog-if 30)
Subsystem: Device [1d5c:1000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at d6000000 (32-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
06:00.0 Ethernet controller [0200]: Atheros Communications AR8131 Gigabit
Ethernet [1969:1063] (rev c0)
Subsystem: ASUSTeK Computer Inc. Device [1043:1820]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at d3800000 (64-bit, non-prefetchable) [size=256K]
Region 2: I/O ports at 8000 [size=128]
Capabilities: <access denied>
Kernel driver in use: atl1c
ff:00.0 Host bridge [0600]: Intel Corporation Core Processor QuickPath
Architecture Generic Non-core Registers [8086:2c62] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:00.1 Host bridge [0600]: Intel Corporation Core Processor QuickPath
Architecture System Address Decoder [8086:2d01] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:02.0 Host bridge [0600]: Intel Corporation Core Processor QPI Link 0
[8086:2d10] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:02.1 Host bridge [0600]: Intel Corporation Core Processor QPI Physical 0
[8086:2d11] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:02.2 Host bridge [0600]: Intel Corporation Core Processor Reserved
[8086:2d12] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:02.3 Host bridge [0600]: Intel Corporation Core Processor Reserved
[8086:2d13] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 003: ID 04f2:b1bb Chicony Electronics Co., Ltd
Bus 002 Device 003: ID 046d:c52b Logitech, Inc. Unifying Receiver
-- System Information:
Debian Release: wheezy/sid
APT prefers testing-proposed-updates
APT policy: (500, 'testing-proposed-updates'), (500, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.32-5-amd64 (SMP w/4 CPU cores)
Locale: LANG=pl_PL.utf8, LC_CTYPE=pl_PL.utf8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.32-5-amd64 depends on:
ii debconf [debconf-2.0] 1.5.38 Debian configuration management sy
ii initramfs-tools [linux-initra 0.98.8 tools for generating an initramfs
ii linux-base 2.6.32-30 Linux image base package
ii module-init-tools 3.12-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.32-5-amd64 recommends:
ii firmware-linux-free 2.6.32-30 Binary firmware for various driver
Versions of packages linux-image-2.6.32-5-amd64 suggests:
pn grub | lilo <none> (no description available)
pn linux-doc-2.6.32 <none> (no description available)
Versions of packages linux-image-2.6.32-5-amd64 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information:
linux-image-2.6.32-5-amd64/postinst/ignoring-do-bootloader-2.6.32-5-amd64:
linux-image-2.6.32-5-amd64/postinst/depmod-error-initrd-2.6.32-5-amd64: false
linux-image-2.6.32-5-amd64/prerm/removing-running-kernel-2.6.32-5-amd64: true
linux-image-2.6.32-5-amd64/postinst/missing-firmware-2.6.32-5-amd64:
--
To UNSUBSCRIBE, email to debian-kernel-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
Archive: http://lists.debian.org/20110223145749.3578.80285.reportbug@zeissmann
