Package: linux-2.6 Version: 2.6.26-26lenny1 Severity: normal I've recently installed Lenny on an old HP NetServer E60 machine. The installer worked perfectly, but after the reboot I got a kernel panic with flashing keyboard lights.
A search lead me to bug 486168, which seems very similar (same hardware, same panic message). The comments there suggest using rescue mode to install a 486 kernel and boot it. I did that, and the system now works, but the 486 kernel recognizes just one CPU and not both. (I'm not sure if this is a limitation of the 486 kernel or not) A late comment in bug 486168 suggests disabling the memory hole in the BIOS settings. I checked the BIOS settings on my machine and the memory hole is disabled, yet the kernel panic still happens. I'd like to load the 686 kernel for increased performance, and possibly to take advantage of SMP. -- Package-specific info: ** Kernel log: boot messages should be attached Can't make it save the boot messages to a file, so uploaded as YouTube video at: http://www.youtube.com/watch?v=0ahFTUIY4ZY I hope the quality is enough. crash it around 00:22 Note that I edited the kernel command line in grub. I did this to remove the "quiet" option, so that more info is on screen. ** Model information HP NetServer E60 ** Network interface configuration: # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface allow-hotplug eth1 iface eth1 inet dhcp ** PCI devices: 00:00.0 Host bridge [0600]: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge [8086:7190] (rev 03) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 64 Region 0: Memory at 30000000 (32-bit, prefetchable) [size=256M] Capabilities: [a0] AGP version 1.0 Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none> Kernel driver in use: agpgart-intel Kernel modules: intel-agp 00:01.0 PCI bridge [0604]: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge [8086:7191] (rev 03) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 128 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 00009000-00009fff Memory behind bridge: fc200000-fc2fffff Prefetchable memory behind bridge: fd000000-fdffffff Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B+ PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Kernel modules: shpchp 00:04.0 ISA bridge [0601]: Intel Corporation 82371AB/EB/MB PIIX4 ISA [8086:7110] (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:04.1 IDE interface [0101]: Intel Corporation 82371AB/EB/MB PIIX4 IDE [8086:7111] (rev 01) (prog-if 80 [Master]) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8] Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1] Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8] Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1] Region 4: I/O ports at 1860 [size=16] Kernel driver in use: PIIX_IDE Kernel modules: piix 00:04.2 USB Controller [0c03]: Intel Corporation 82371AB/EB/MB PIIX4 USB [8086:7112] (rev 01) (prog-if 00 [UHCI]) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 Interrupt: pin D routed to IRQ 19 Region 4: I/O ports at 1840 [size=32] Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:04.3 Bridge [0680]: Intel Corporation 82371AB/EB/MB PIIX4 ACPI [8086:7113] (rev 02) Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin ? routed to IRQ 9 Kernel driver in use: piix4_smbus Kernel modules: i2c-piix4 00:05.0 SCSI storage controller [0100]: Adaptec AHA-2940U/UW / AHA-39xx / AIC-7895 [9004:7895] (rev 04) Subsystem: Adaptec AHA-2940U/2940UW Dual AHA-394xAU/AUW/AUWD AIC-7895B [9004:7895] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (2000ns min, 2000ns max) Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at 1000 [disabled] [size=256] Region 1: Memory at fc100000 (32-bit, non-prefetchable) [size=4K] [virtual] Expansion ROM at 20100000 [disabled] [size=64K] Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: aic7xxx Kernel modules: aic7xxx 00:05.1 SCSI storage controller [0100]: Adaptec AHA-2940U/UW / AHA-39xx / AIC-7895 [9004:7895] (rev 04) Subsystem: Adaptec AHA-2940U/2940UW Dual AHA-394xAU/AUW/AUWD AIC-7895B [9004:7895] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (2000ns min, 2000ns max) Interrupt: pin B routed to IRQ 18 Region 0: I/O ports at 1400 [disabled] [size=256] Region 1: Memory at fc101000 (32-bit, non-prefetchable) [size=4K] Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: aic7xxx Kernel modules: aic7xxx 00:06.0 Ethernet controller [0200]: Intel Corporation 82557/8/9/0/1 Ethernet Pro 100 [8086:1229] (rev 08) Subsystem: Hewlett-Packard Company NetServer 10/100TX [103c:10ca] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 66 (2000ns min, 14000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 19 Region 0: Memory at fc102000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at 1800 [size=64] Region 2: Memory at fc000000 (32-bit, non-prefetchable) [size=1M] [virtual] Expansion ROM at 20000000 [disabled] [size=1M] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=2 PME- Kernel driver in use: e100 Kernel modules: eepro100, e100 00:0c.0 PCI bridge [0604]: Digital Equipment Corporation DECchip 21152 [1011:0024] (rev 03) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 57, Cache Line Size: 32 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=36 I/O behind bridge: 00002000-00002fff Memory behind bridge: fc300000-fc3fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn- Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=220mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Bridge: PM- B3+ Kernel modules: shpchp 01:00.0 VGA compatible controller [0300]: ATI Technologies Inc 3D Rage IIC AGP [1002:475a] (rev 7a) (prog-if 00 [VGA controller]) Subsystem: ATI Technologies Inc Rage 3D Pro AGP 2x XPERT 98 [1002:0084] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 66 (2000ns min), Cache Line Size: 32 bytes Region 0: Memory at fd000000 (32-bit, prefetchable) [size=16M] Region 1: I/O ports at 9000 [size=256] Region 2: Memory at fc200000 (32-bit, non-prefetchable) [size=4K] [virtual] Expansion ROM at fc220000 [disabled] [size=128K] Capabilities: [5c] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 02:03.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RT8139 [10ec:8139] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (8000ns min, 16000ns max) Interrupt: pin A routed to IRQ 19 Region 0: I/O ports at 2000 [size=256] Region 1: Memory at fc300000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: 8139too Kernel modules: 8139too, 8139cp ** USB devices: Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub -- System Information: Debian Release: 5.0.7 APT prefers stable APT policy: (500, 'stable') Architecture: i386 (i686) Kernel: Linux 2.6.26-2-486 Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/bash Versions of packages linux-image-2.6.26-2-686 depends on: ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy ii initramfs-tools [linux-initra 0.92o tools for generating an initramfs ii module-init-tools 3.4-1 tools for managing Linux kernel mo Versions of packages linux-image-2.6.26-2-686 recommends: ii libc6-i686 2.7-18lenny6 GNU C Library: Shared libraries [i Versions of packages linux-image-2.6.26-2-686 suggests: ii grub 0.97-47lenny2 GRand Unified Bootloader (Legacy v pn linux-doc-2.6.26 <none> (no description available) Versions of packages linux-image-2.6.26-2-686 is related to: pn firmware-bnx2 <none> (no description available) pn firmware-bnx2x <none> (no description available) pn firmware-ipw2x00 <none> (no description available) pn firmware-ivtv <none> (no description available) pn firmware-iwlwifi <none> (no description available) pn firmware-linux <none> (no description available) pn firmware-linux-nonfree <none> (no description available) pn firmware-qlogic <none> (no description available) pn firmware-ralink <none> (no description available) -- debconf information: linux-image-2.6.26-2-686/postinst/bootloader-error-2.6.26-2-686: shared/kernel-image/really-run-bootloader: true linux-image-2.6.26-2-686/postinst/old-dir-initrd-link-2.6.26-2-686: true linux-image-2.6.26-2-686/preinst/overwriting-modules-2.6.26-2-686: true linux-image-2.6.26-2-686/postinst/bootloader-test-error-2.6.26-2-686: linux-image-2.6.26-2-686/postinst/depmod-error-2.6.26-2-686: false linux-image-2.6.26-2-686/preinst/bootloader-initrd-2.6.26-2-686: true linux-image-2.6.26-2-686/preinst/abort-overwrite-2.6.26-2-686: linux-image-2.6.26-2-686/preinst/abort-install-2.6.26-2-686: linux-image-2.6.26-2-686/postinst/depmod-error-initrd-2.6.26-2-686: false linux-image-2.6.26-2-686/postinst/create-kimage-link-2.6.26-2-686: true linux-image-2.6.26-2-686/preinst/failed-to-move-modules-2.6.26-2-686: linux-image-2.6.26-2-686/preinst/initrd-2.6.26-2-686: linux-image-2.6.26-2-686/preinst/lilo-has-ramdisk: linux-image-2.6.26-2-686/prerm/would-invalidate-boot-loader-2.6.26-2-686: true linux-image-2.6.26-2-686/postinst/kimage-is-a-directory: linux-image-2.6.26-2-686/postinst/old-initrd-link-2.6.26-2-686: true linux-image-2.6.26-2-686/preinst/elilo-initrd-2.6.26-2-686: true linux-image-2.6.26-2-686/preinst/lilo-initrd-2.6.26-2-686: true linux-image-2.6.26-2-686/prerm/removing-running-kernel-2.6.26-2-686: true linux-image-2.6.26-2-686/postinst/old-system-map-link-2.6.26-2-686: true -- To UNSUBSCRIBE, email to debian-kernel-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org Archive: http://lists.debian.org/20101222091254.2319.92059.report...@nibbler.cogniview.local
