Hi,
after a system upgrade to the current state of Debian Testing - which
included an upgrade
of the linux-image-2.6.32-5-amd64 package to the version 2.6.32.28 - a
kernel failure occured.
The failure message has been sent to kerneloops.com and is also shown below.
Don't know if this has to do with the suspend to ram problem. At least
the suspend to ram
problem still exists in this kernel version as I tried and was able to
reproduce it.
If I should add this info to bugzilla.kernel.org - please let me know.
Regards
Kernel failure message 1:
] EDAC amd64: WARNING: ECC is NOT currently enabled by the BIOS. Module
will NOT be loaded.
Either Enable ECC in the BIOS, or use the 'ecc_enable_override'
parameter.
Might be a BIOS bug, if BIOS says ECC is enabled
Use of the override can cause unknown side effects.
amd64_edac: probe of 0000:00:18.2 failed with error -22
tifm_7xx1 0000:02:04.2: PCI INT A -> GSI 20 (level, low) -> IRQ 20
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
b43-phy0: Broadcom 4311 WLAN found (core revision 10)
HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
phy0: Selected rate control algorithm 'minstrel'
Broadcom 43xx driver loaded [ Features: PML, Firmware-ID: FW13 ]
input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:14.2/input/input11
Adding 3148700k swap on /dev/sda5. Priority:-1 extents:1 across:3148700k
EXT4-fs (sda7): internal journal on sda7:8
loop: module loaded
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
tg3 0000:02:01.0: firmware: requesting tigon/tg3_tso5.bin
tg3 0000:02:01.0: PME# disabled
ADDRCONF(NETDEV_UP): eth0: link is not ready
fuse init (API version 7.12)
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
input: ACPI Virtual Keyboard Device as /devices/virtual/input/input12
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.13
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bridge firewalling registered
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
alloc irq_desc for 17 on node 0
alloc kstat_irqs on node 0
pci 0000:01:05.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[drm] Initialized drm 1.1.0 20060810
radeon: Unknown parameter `modeset'
powernow-k8: Found 1 AMD Turion(tm) 64 X2 Mobile Technology TL-52
processors (2 cpu cores) (version 2.20.00)
powernow-k8: 0 : fid 0x8 (1600 MHz), vid 0x13
powernow-k8: 1 : fid 0x0 (800 MHz), vid 0x1e
Clocksource tsc unstable (delta = -122312474 ns)
eth0: no IPv6 routers present
--
To UNSUBSCRIBE, email to debian-kernel-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
Archive: http://lists.debian.org/4cf37aaf.4010...@online.de
