--- Begin Message ---
Package: linux-2.6
Version: 2.6.32-21
Severity: important
Hello everyone,
the recent update of linux-image-2.6.32 to 2.6.32-21 disables KMS for i8xx
chipsets. This causes the xorg-video-intel driver to hang on X startup on my
system. While X works with the vesa driver, it does not seem to have any
support for an external monitor,
xv or hardware acceleration, which I consider a serious drawback. The
functionality of my laptop (ThinkPad X40)
is greatly reduced, hence the "important" tag.
It would be helpful to have a way to switch KMS back on for these chips for
configurations or systems where it works fine.
Regards,
soenke
-- Package-specific info:
** Version:
Linux version 2.6.32-5-686 (Debian 2.6.32-21) (b...@decadent.org.uk) (gcc
version 4.3.5 (Debian 4.3.5-2) ) #1 SMP Wed Aug 25 14:28:12 UTC 2010
** Command line:
BOOT_IMAGE=/vmlinuz-2.6.32-5-686 root=UUID=7d1dda14-2a82-4a6e-8456-684843390f30
ro quiet
** Not tainted
** Kernel log:
[ 186.960072] uhci_hcd 0000:00:1d.0: power state changed by ACPI to D3
[ 187.000065] ACPI: Preparing to enter system sleep state S3
[ 187.180190] Disabling non-boot CPUs ...
[ 187.180289] Extended CMOS year: 2000
[ 187.180289] Back to C!
[ 187.180289] CPU0: Thermal monitoring enabled (TM2)
[ 187.180289] Extended CMOS year: 2000
[ 187.180335] ACPI: Waking up from system sleep state S3
[ 187.712190] pci 0000:00:02.1: restoring config space at offset 0x5 (was 0x0,
writing 0xd0080000)
[ 187.712196] pci 0000:00:02.1: restoring config space at offset 0x4 (was 0x8,
writing 0xe8000008)
[ 187.712203] pci 0000:00:02.1: restoring config space at offset 0x1 (was
0x900000, writing 0x900003)
[ 187.756061] uhci_hcd 0000:00:1d.0: power state changed by ACPI to D0
[ 187.764071] uhci_hcd 0000:00:1d.0: power state changed by ACPI to D0
[ 187.764078] uhci_hcd 0000:00:1d.0: restoring config space at offset 0xf (was
0x100, writing 0x10b)
[ 187.764090] uhci_hcd 0000:00:1d.0: restoring config space at offset 0x8 (was
0x1, writing 0x1821)
[ 187.764102] uhci_hcd 0000:00:1d.0: restoring config space at offset 0x1 (was
0x2800000, writing 0x2800001)
[ 187.772072] uhci_hcd 0000:00:1d.0: power state changed by ACPI to D0
[ 187.780071] uhci_hcd 0000:00:1d.0: power state changed by ACPI to D0
[ 187.788071] uhci_hcd 0000:00:1d.1: power state changed by ACPI to D0
[ 187.796071] uhci_hcd 0000:00:1d.1: power state changed by ACPI to D0
[ 187.796077] uhci_hcd 0000:00:1d.1: restoring config space at offset 0xf (was
0x200, writing 0x20b)
[ 187.796089] uhci_hcd 0000:00:1d.1: restoring config space at offset 0x8 (was
0x1, writing 0x1841)
[ 187.796102] uhci_hcd 0000:00:1d.1: restoring config space at offset 0x1 (was
0x2800000, writing 0x2800001)
[ 187.804071] uhci_hcd 0000:00:1d.1: power state changed by ACPI to D0
[ 187.812071] uhci_hcd 0000:00:1d.1: power state changed by ACPI to D0
[ 187.812078] uhci_hcd 0000:00:1d.2: restoring config space at offset 0xf (was
0x300, writing 0x30b)
[ 187.812091] uhci_hcd 0000:00:1d.2: restoring config space at offset 0x8 (was
0x1, writing 0x1861)
[ 187.812103] uhci_hcd 0000:00:1d.2: restoring config space at offset 0x1 (was
0x2800000, writing 0x2800001)
[ 187.812121] ehci_hcd 0000:00:1d.7: restoring config space at offset 0xf (was
0x400, writing 0x40b)
[ 187.812139] ehci_hcd 0000:00:1d.7: restoring config space at offset 0x4 (was
0x0, writing 0xd0100000)
[ 187.812148] ehci_hcd 0000:00:1d.7: restoring config space at offset 0x1 (was
0x2900000, writing 0x2900102)
[ 187.820074] ehci_hcd 0000:00:1d.7: power state changed by ACPI to D0
[ 187.828071] ehci_hcd 0000:00:1d.7: power state changed by ACPI to D0
[ 187.828125] ata_piix 0000:00:1f.1: restoring config space at offset 0x9 (was
0x0, writing 0x50000000)
[ 187.828138] ata_piix 0000:00:1f.1: restoring config space at offset 0x1 (was
0x2800005, writing 0x2800007)
[ 187.828183] Intel ICH 0000:00:1f.5: restoring config space at offset 0x1
(was 0x2900007, writing 0x2900003)
[ 187.828211] Intel ICH Modem 0000:00:1f.6: restoring config space at offset
0x1 (was 0x2900005, writing 0x2900001)
[ 187.844043] sdhci-pci 0000:02:00.1: restoring config space at offset 0x3
(was 0x800000, writing 0x804000)
[ 187.844050] sdhci-pci 0000:02:00.1: restoring config space at offset 0x1
(was 0x2100000, writing 0x2100106)
[ 187.844069] e1000 0000:02:01.0: restoring config space at offset 0xf (was
0xff0100, writing 0xff010b)
[ 187.844083] e1000 0000:02:01.0: restoring config space at offset 0x6 (was
0x1, writing 0x7001)
[ 187.844089] e1000 0000:02:01.0: restoring config space at offset 0x4 (was
0x0, writing 0xd0200000)
[ 187.844095] e1000 0000:02:01.0: restoring config space at offset 0x3 (was
0x0, writing 0x4008)
[ 187.844102] e1000 0000:02:01.0: restoring config space at offset 0x1 (was
0x2300000, writing 0x2300117)
[ 187.891603] uhci_hcd 0000:00:1d.0: power state changed by ACPI to D0
[ 187.891796] uhci_hcd 0000:00:1d.0: power state changed by ACPI to D0
[ 187.891808] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 187.891816] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 187.891836] usb usb2: root hub lost power or was reset
[ 187.892041] uhci_hcd 0000:00:1d.1: power state changed by ACPI to D0
[ 187.892199] uhci_hcd 0000:00:1d.1: power state changed by ACPI to D0
[ 187.892205] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 187.892212] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 187.892229] usb usb3: root hub lost power or was reset
[ 187.892246] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 187.892252] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 187.892270] usb usb4: root hub lost power or was reset
[ 187.892448] ehci_hcd 0000:00:1d.7: power state changed by ACPI to D0
[ 187.892617] ehci_hcd 0000:00:1d.7: power state changed by ACPI to D0
[ 187.892625] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23
[ 187.892632] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 187.892645] pci 0000:00:1e.0: setting latency timer to 64
[ 187.892656] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 187.892662] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 187.895611] Intel ICH 0000:00:1f.5: PCI INT B -> GSI 17 (level, low) -> IRQ
17
[ 187.895617] Intel ICH 0000:00:1f.5: setting latency timer to 64
[ 188.906104] Intel ICH Modem 0000:00:1f.6: PCI INT B -> GSI 17 (level, low)
-> IRQ 17
[ 188.906111] Intel ICH Modem 0000:00:1f.6: setting latency timer to 64
[ 189.513024] ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (SET FEATURES) succeeded
[ 189.513030] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK)
filtered out
[ 189.513035] ata1.00: ACPI cmd ef/03:45:00:00:00:a0 (SET FEATURES) filtered
out
[ 189.513040] ata1.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES) filtered
out
[ 189.536748] ata1.00: configured for UDMA/100
[ 189.560772] ata1.00: configured for UDMA/100
[ 189.560776] ata1: EH complete
[ 190.048245] sdhci-pci 0000:02:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ
17
[ 190.049253] e1000 0000:02:01.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 190.049265] pci 0000:00:1e.0: wake-up capability disabled by ACPI
[ 190.049270] e1000 0000:02:01.0: PME# disabled
[ 190.250410] wlan0: Coming out of suspend...
[ 190.250417] ipw2200 0000:02:02.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 190.275920] sd 0:0:0:0: [sda] Starting disk
[ 190.376722] pci 0000:00:02.0: power state changed by ACPI to D0
[ 190.376771] pci 0000:00:02.0: power state changed by ACPI to D0
[ 190.376777] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 190.376782] pci 0000:00:02.0: setting latency timer to 64
[ 190.527805] hdaps: initial mode latch is 0x01
[ 190.527934] hdaps: setting ec_rate=250, filter_order=2
[ 190.528325] PM: Finishing wakeup.
[ 190.528328] Restarting tasks ... done.
[ 193.771456] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 193.828047] usb 4-1: new full speed USB device using uhci_hcd and address 3
[ 194.046947] usb 4-1: New USB device found, idVendor=1668, idProduct=2441
[ 194.046953] usb 4-1: New USB device strings: Mfr=0, Product=0, SerialNumber=3
[ 194.046957] usb 4-1: SerialNumber: 〳㈴〱ㄴ㌷㌳
[ 194.047107] usb 4-1: configuration #1 chosen from 1 choice
[ 194.065326] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 194.272967] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 196.607748] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 207.056034] wlan0: no IPv6 routers present
** Model information
not available
** Loaded modules:
Module Size Used by
lib80211_crypt_ccmp 3643 3
ext3 94204 1
jbd 32169 1 ext3
acpi_cpufreq 4943 1
cpufreq_powersave 602 0
cpufreq_conservative 4018 0
cpufreq_userspace 1480 0
cpufreq_stats 1940 0
parport_pc 15799 0
ppdev 4058 0
lp 5570 0
parport 22554 3 parport_pc,ppdev,lp
sco 5857 2
rfcomm 25171 12
bridge 32987 0
stp 996 1 bridge
bnep 7444 2
l2cap 21705 16 rfcomm,bnep
nfsd 193279 11
lockd 49437 1 nfsd
nfs_acl 1695 1 nfsd
vboxnetadp 5118 0
vboxnetflt 12555 0
auth_rpcgss 25240 1 nfsd
sunrpc 134584 10 nfsd,lockd,nfs_acl,auth_rpcgss
vboxdrv 126574 2 vboxnetadp,vboxnetflt
exportfs 2618 1 nfsd
uinput 4796 1
fuse 43762 1
nf_conntrack_ipv4 7597 4
nf_defrag_ipv4 779 1 nf_conntrack_ipv4
xt_state 927 4
nf_conntrack 38075 2 nf_conntrack_ipv4,xt_state
iptable_filter 1790 1
ip_tables 7690 1 iptable_filter
x_tables 8327 2 xt_state,ip_tables
joydev 6771 0
hdaps 6493 0
tp_smapi 13592 0
thinkpad_ec 3454 2 hdaps,tp_smapi
loop 9765 0
sha256_generic 10748 4
aes_i586 6816 7
aes_generic 25738 1 aes_i586
cbc 2047 2
dm_crypt 9127 2
dm_mod 46082 5 dm_crypt
snd_intel8x0 19523 1
snd_intel8x0m 8100 0
snd_ac97_codec 79148 2 snd_intel8x0,snd_intel8x0m
pcmcia 17442 0
ac97_bus 710 1 snd_ac97_codec
sdhci_pci 4525 0
snd_pcm_oss 28671 0
snd_mixer_oss 10461 1 snd_pcm_oss
snd_pcm 47214 4
snd_intel8x0,snd_intel8x0m,snd_ac97_codec,snd_pcm_oss
snd_seq_midi 3576 0
btusb 8017 2
yenta_socket 16403 1
sdhci 12147 1 sdhci_pci
rsrc_nonstatic 7057 1 yenta_socket
snd_rawmidi 12513 1 snd_seq_midi
snd_seq_midi_event 3684 1 snd_seq_midi
pcmcia_core 20450 3 pcmcia,yenta_socket,rsrc_nonstatic
mmc_core 38491 1 sdhci
bluetooth 36319 9 sco,rfcomm,bnep,l2cap,btusb
thinkpad_acpi 41975 0
snd_seq 35463 2 snd_seq_midi,snd_seq_midi_event
snd_timer 12258 2 snd_pcm,snd_seq
e1000 77289 0
snd_seq_device 3673 3 snd_seq_midi,snd_rawmidi,snd_seq
ipw2200 108368 0
uhci_hcd 16057 0
rfkill 10264 3 bluetooth,thinkpad_acpi
led_class 1757 2 sdhci,thinkpad_acpi
libipw 18439 1 ipw2200
snd 34363 12
snd_intel8x0,snd_intel8x0m,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
ehci_hcd 27851 0
lib80211 2870 3 lib80211_crypt_ccmp,ipw2200,libipw
shpchp 21220 0
soundcore 3450 1 snd
irda 75924 0
i2c_i801 6462 0
snd_page_alloc 5045 3 snd_intel8x0,snd_intel8x0m,snd_pcm
pci_hotplug 18065 1 shpchp
nvram 3985 1 thinkpad_acpi
usbcore 98397 4 btusb,uhci_hcd,ehci_hcd
crc_ccitt 1039 1 irda
battery 3782 0
ac 1640 0
processor 26671 2 acpi_cpufreq
serio_raw 2916 0
nls_base 4541 1 usbcore
psmouse 44657 0
evdev 5609 21
rng_core 2178 0
ext4 257739 7
mbcache 3762 2 ext3,ext4
jbd2 56155 1 ext4
crc16 1027 2 l2cap,ext4
i915 221767 0
sd_mod 25869 10
crc_t10dif 1012 1 sd_mod
drm_kms_helper 18305 1 i915
ata_generic 2019 0
drm 112020 2 i915,drm_kms_helper
i2c_algo_bit 3497 1 i915
ata_piix 17736 9
i2c_core 12696 5 i2c_i801,i915,drm_kms_helper,drm,i2c_algo_bit
libata 115721 2 ata_generic,ata_piix
thermal 9206 0
video 14605 1 i915
scsi_mod 101401 2 sd_mod,libata
thermal_sys 9378 3 processor,thermal,video
button 3598 1 i915
output 1204 1 video
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82852/82855 GM/GME/PM/GMV
Processor to I/O Controller [8086:3580] (rev 02)
Subsystem: IBM ThinkPad R50e [1014:055c]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at <unassigned> (32-bit, prefetchable)
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:00.1 System peripheral [0880]: Intel Corporation 82852/82855 GM/GME/PM/GMV
Processor to I/O Controller [8086:3584] (rev 02)
Subsystem: IBM ThinkPad R50e [1014:055d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.3 System peripheral [0880]: Intel Corporation 82852/82855 GM/GME/PM/GMV
Processor to I/O Controller [8086:3585] (rev 02)
Subsystem: IBM ThinkPad R50e [1014:055e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
00:02.0 VGA compatible controller [0300]: Intel Corporation 82852/855GM
Integrated Graphics Device [8086:3582] (rev 02) (prog-if 00 [VGA controller])
Subsystem: IBM Device [1014:0557]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at d0000000 (32-bit, non-prefetchable) [size=512K]
Region 2: I/O ports at 1800 [size=8]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
00:02.1 Display controller [0380]: Intel Corporation 82852/855GM Integrated
Graphics Device [8086:3582] (rev 02)
Subsystem: IBM Device [1014:0557]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at d0080000 (32-bit, non-prefetchable) [size=512K]
Capabilities: <access denied>
00:1d.0 USB Controller [0c03]: Intel Corporation 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 [8086:24c2] (rev 01) (prog-if 00
[UHCI])
Subsystem: IBM ThinkPad [1014:052d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at 1820 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 [8086:24c4] (rev 01) (prog-if 00
[UHCI])
Subsystem: IBM ThinkPad [1014:052d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 1840 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 [8086:24c7] (rev 01) (prog-if 00
[UHCI])
Subsystem: IBM ThinkPad [1014:052d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 1860 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2
EHCI Controller [8086:24cd] (rev 01) (prog-if 20 [EHCI])
Subsystem: IBM ThinkPad [1014:052e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 0: Memory at d0100000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge
[8086:2448] (rev 81) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR+ INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=05, sec-latency=64
I/O behind bridge: 00003000-00007fff
Memory behind bridge: d0200000-dfffffff
Prefetchable memory behind bridge: f0000000-f7ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:1f.0 ISA bridge [0601]: Intel Corporation 82801DBM (ICH4-M) LPC Interface
Bridge [8086:24cc] (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:1f.1 IDE interface [0101]: Intel Corporation 82801DBM (ICH4-M) IDE
Controller [8086:24ca] (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: IBM ThinkPad [1014:052d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 1810 [size=16]
Region 5: Memory at 50000000 (32-bit, non-prefetchable) [size=1K]
Kernel driver in use: ata_piix
00:1f.3 SMBus [0c05]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M)
SMBus Controller [8086:24c3] (rev 01)
Subsystem: IBM ThinkPad [1014:052d]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 1880 [size=32]
Kernel driver in use: i801_smbus
00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller [8086:24c5] (rev 01)
Subsystem: IBM Device [1014:0558]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at 1c00 [size=256]
Region 1: I/O ports at 18c0 [size=64]
Region 2: Memory at d0100c00 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at d0100800 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: Intel ICH
00:1f.6 Modem [0703]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M)
AC'97 Modem Controller [8086:24c6] (rev 01) (prog-if 00 [Generic])
Subsystem: IBM Device [1014:055a]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at 2400 [size=256]
Region 1: I/O ports at 2000 [size=128]
Capabilities: <access denied>
Kernel driver in use: Intel ICH Modem
02:00.0 CardBus bridge [0607]: Ricoh Co Ltd RL5c476 II [1180:0476] (rev 8d)
Subsystem: IBM Device [1014:0555]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168
Interrupt: pin A routed to IRQ 16
Region 0: Memory at b0000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=04, sec-latency=176
Memory window 0: f0000000-f3fff000 (prefetchable)
Memory window 1: d4000000-d7fff000
I/O window 0: 00003000-000030ff
I/O window 1: 00003400-000034ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
02:00.1 SD Host controller [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro
Host Adapter [1180:0822] (rev 13)
Subsystem: IBM ThinkPad X60s / Z60t [1014:0556]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin B routed to IRQ 17
Region 0: Memory at d0221000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: sdhci-pci
02:01.0 Ethernet controller [0200]: Intel Corporation 82541GI Gigabit Ethernet
Controller [8086:1077]
Subsystem: IBM Device [1014:055b]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (63750ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at d0200000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 7000 [size=64]
Capabilities: <access denied>
Kernel driver in use: e1000
02:02.0 Network controller [0280]: Intel Corporation PRO/Wireless 2200BG
[Calexico2] Network Connection [8086:4220] (rev 05)
Subsystem: Intel Corporation Device [8086:2711]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (750ns min, 6000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at d0220000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ipw2200
** USB devices:
Bus 004 Device 003: ID 1668:2441 Actiontec Electronics, Inc. [hex] BMDC-2 IBM
Bluetooth III w.56k
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: squeeze/sid
APT prefers testing
APT policy: (900, 'testing'), (800, 'unstable'), (700, 'experimental')
Architecture: i386 (i686)
Kernel: Linux 2.6.32-5-686 (SMP w/1 CPU core)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.32-5-686 depends on:
ii debconf [debconf-2.0] 1.5.35 Debian configuration management sy
ii initramfs-tools [linux-initra 0.98.1 tools for generating an initramfs
ii linux-base 2.6.32-21 Linux image base package
ii module-init-tools 3.12-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.32-5-686 recommends:
ii firmware-linux-free 2.6.32-21 Binary firmware for various driver
ii libc6-i686 2.11.2-2 GNU C Library: Shared libraries [i
Versions of packages linux-image-2.6.32-5-686 suggests:
pn grub | lilo <none> (no description available)
pn linux-doc-2.6.32 <none> (no description available)
Versions of packages linux-image-2.6.32-5-686 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
ii firmware-ipw2x00 0.26 Binary firmware for Intel Pro Wire
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.32-5-686/prerm/removing-running-kernel-2.6.32-5-686: true
linux-image-2.6.32-5-686/prerm/would-invalidate-boot-loader-2.6.32-5-686: true
linux-image-2.6.32-5-686/postinst/bootloader-test-error-2.6.32-5-686:
linux-image-2.6.32-5-686/postinst/bootloader-error-2.6.32-5-686:
linux-image-2.6.32-5-686/postinst/depmod-error-initrd-2.6.32-5-686: false
linux-image-2.6.32-5-686/postinst/ignoring-do-bootloader-2.6.32-5-686:
linux-image-2.6.32-5-686/postinst/missing-firmware-2.6.32-5-686:
--- End Message ---