Your message dated Wed, 25 Aug 2010 01:57:58 +0000
with message-id <e1oo5fw-0002fa...@franck.debian.org>
and subject line Bug#589179: fixed in user-mode-linux 2.6.26-1um-2+24lenny1
has caused the Debian Bug report #589179,
regarding linux-image-2.6.26-2-686: heap base address is not randomised when
randomize_va_space is set to 2
to be marked as done.
This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.
(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact ow...@bugs.debian.org
immediately.)
--
589179: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=589179
Debian Bug Tracking System
Contact ow...@bugs.debian.org with problems
--- Begin Message ---
Package: linux-2.6
Version: 2.6.26-24
Severity: normal
Hi,
When running the latest stable Debian kernel the base address of a heap is not
randomised regardless of the
setting for randomize_va_space (it is set to 2 by default). This can be
observed by using a simple .c
program (below) or using the paxtest suite available from here:
http://grsecurity.net/~spender/paxtest-0.9.9.tgz
Please bear in mind that I only have tested this within virtualised environment
and I have only tested a x86 system.
sample c program I used:
#include <stdio.h>
#include <stdlib.h>
void main() {
char * p = (char *) malloc(40*sizeof(char));
printf("address: %x\n",p);
}
compile and run:
gcc -o heap heap.c
watch -n 1 ./heap
reproducible: always
steps to reproduce:
- compile and run paxtest or simple .c program from above
expected results:
- randomised addressed for heap allocations - address of the malloc'ed var
should be different each time the program is run.
For the paxtest - it should not report 'no randomisation' for 'Heap
randomisation test (ET_EXEC)'
actual results:
- no randomisation of the heap base addresses.
-- Package-specific info:
** Version:
Linux version 2.6.26-2-686 (Debian 2.6.26-24) (da...@debian.org) (gcc version
4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Mon Jun 21 05:58:44 UTC
2010
** Command line:
root=/dev/hda1 ro quiet
** Not tainted
** Kernel log:
[ 5.227996] usb 1-1: new full speed USB device using uhci_hcd and address 2
[ 5.485259] PM: Starting manual resume from disk
[ 5.517670] EXT3-fs: INFO: recovery required on readonly filesystem.
[ 5.517674] EXT3-fs: write access will be enabled during recovery.
[ 5.590701] usb 1-1: configuration #1 chosen from 1 choice
[ 5.643904] usb 1-1: New USB device found, idVendor=0627, idProduct=0001
[ 5.643909] usb 1-1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.643912] usb 1-1: Product: QEMU USB Tablet
[ 5.643914] usb 1-1: Manufacturer: QEMU 0.12.4
[ 5.643916] usb 1-1: SerialNumber: 1
[ 5.710778] usbcore: registered new interface driver hiddev
[ 5.735324] input: QEMU 0.12.4 QEMU USB Tablet as /class/input/input1
[ 5.739330] input,hidraw0: USB HID v0.01 Pointer [QEMU 0.12.4 QEMU USB
Tablet] on usb-0000:00:01.2-1
[ 5.739330] usbcore: registered new interface driver usbhid
[ 5.739330] usbhid: v2.6:USB HID core driver
[ 6.359345] kjournald starting. Commit interval 5 seconds
[ 6.359345] EXT3-fs: recovery complete.
[ 6.359345] EXT3-fs: mounted filesystem with ordered data mode.
[ 9.039926] udevd version 125 started
[ 9.809803] udev: renamed network interface eth0 to eth6
[ 10.587020] piix4_smbus 0000:00:01.3: Found 0000:00:01.3 device
[ 10.797426] input: Power Button (FF) as /class/input/input2
[ 10.828746] ACPI: Power Button (FF) [PWRF]
[ 11.152352] input: PC Speaker as /class/input/input3
[ 11.368600] input: ImExPS/2 Generic Explorer Mouse as /class/input/input4
[ 11.472414] parport_pc 00:05: reported by Plug and Play ACPI
[ 11.472414] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 12.741775] Adding 489940k swap on /dev/hda5. Priority:-1 extents:1
across:489940k
[ 113.697388] EXT3 FS on hda1, internal journal
[ 114.415953] loop: module loaded
[ 121.243828] NET: Registered protocol family 10
[ 121.246126] lo: Disabled Privacy Extensions
[ 122.529155] lp0: using parport0 (interrupt-driven).
[ 122.667535] ppdev: user-space parallel port driver
[ 126.465548] eth6: link up, 100Mbps, full-duplex, lpa 0x05E1
[ 144.751798] eth6: no IPv6 routers present
[ 808.293430] BUG: soft lockup - CPU#0 stuck for 104s! [swapper:0]
[ 808.293430] Modules linked in: ppdev lp ipv6 cpufreq_ondemand cpufreq_stats
freq_table cpufreq_userspace cpufreq_powersave cpufreq_conservative loop
parport_pc parport pcspkr psmouse serio_raw button i2c_piix4 i2c_core joydev
evdev usbhid hid ff_memless ext3 jbd mbcache ide_cd_mod cdrom ide_disk
ata_generic libata scsi_mod 8139too dock floppy 8139cp mii uhci_hcd piix
ide_pci_generic usbcore ide_core thermal processor fan thermal_sys [last
unloaded: scsi_wait_scan]
[ 808.293430]
[ 808.293430] Pid: 0, comm: swapper Not tainted (2.6.26-2-686 #1)
[ 808.293430] EIP: 0060:[<c0114d94>] EFLAGS: 00000246 CPU: 0
[ 808.293430] EIP is at native_safe_halt+0x2/0x3
[ 808.293430] EAX: c0378000 EBX: c010265b ECX: 0104f000 EDX: 00012276
[ 808.293430] ESI: 00000000 EDI: c036c000 EBP: 00847007 ESP: c0379fe0
[ 808.293430] DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
[ 808.293430] CR0: 8005003b CR2: 085643ac CR3: 0ae94000 CR4: 000006d0
[ 808.293430] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[ 808.293430] DR6: ffff0ff0 DR7: 00000400
[ 808.293430] [<c0102688>] ? default_idle+0x2d/0x53
[ 808.293430] [<c01025d3>] ? cpu_idle+0xb0/0xd0
[ 808.293430] =======================
[ 978.033743] BUG: soft lockup - CPU#1 stuck for 158s! [dbus-daemon:2067]
[ 978.033743] Modules linked in: ppdev lp ipv6 cpufreq_ondemand cpufreq_stats
freq_table cpufreq_userspace cpufreq_powersave cpufreq_conservative loop
parport_pc parport pcspkr psmouse serio_raw button i2c_piix4 i2c_core joydev
evdev usbhid hid ff_memless ext3 jbd mbcache ide_cd_mod cdrom ide_disk
ata_generic libata scsi_mod 8139too dock floppy 8139cp mii uhci_hcd piix
ide_pci_generic usbcore ide_core thermal processor fan thermal_sys [last
unloaded: scsi_wait_scan]
[ 978.033743]
[ 978.033743] Pid: 2067, comm: dbus-daemon Not tainted (2.6.26-2-686 #1)
[ 978.033743] EIP: 0060:[<c012979b>] EFLAGS: 00000287 CPU: 1
[ 978.033743] EIP is at run_timer_softirq+0x16d/0x17c
[ 978.033743] EAX: 0001cb7d EBX: 0000007d ECX: 0001cb7e EDX: df46c3f4
[ 978.033743] ESI: deb35bb8 EDI: df46c000 EBP: c027a06b ESP: deb35bb8
[ 978.033743] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[ 978.033743] CR0: 8005003b CR2: 0855aea4 CR3: 0ae4f000 CR4: 000006d0
[ 978.033743] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[ 978.033743] DR6: ffff0ff0 DR7: 00000400
[ 978.033743] [<c0126669>] ? __do_softirq+0x66/0xd3
[ 978.033743] [<c012671b>] ? do_softirq+0x45/0x53
[ 978.033743] [<c01269d2>] ? irq_exit+0x35/0x69
[ 978.033743] [<c0110299>] ? smp_apic_timer_interrupt+0x6b/0x76
[ 978.033743] [<c0104368>] ? apic_timer_interrupt+0x28/0x30
[ 978.033743] [<c017f152>] ? do_sys_poll+0x140/0x2e7
[ 978.033743] [<c017fa0a>] ? __pollwait+0x0/0xac
[ 978.033743] [<c011b73c>] ? default_wake_function+0x0/0x8
[ 978.033743] [<c011b73c>] ? default_wake_function+0x0/0x8
[ 978.033743] [<c011b73c>] ? default_wake_function+0x0/0x8
[ 978.033743] [<c011b73c>] ? default_wake_function+0x0/0x8
[ 978.033743] [<c011b73c>] ? default_wake_function+0x0/0x8
[ 978.033743] [<c011b73c>] ? default_wake_function+0x0/0x8
[ 978.033743] [<c011b73c>] ? default_wake_function+0x0/0x8
[ 978.033743] [<c011b73c>] ? default_wake_function+0x0/0x8
[ 978.033743] [<c011b73c>] ? default_wake_function+0x0/0x8
[ 978.033743] [<c011b73c>] ? default_wake_function+0x0/0x8
[ 978.033743] [<c011b73c>] ? default_wake_function+0x0/0x8
[ 978.033743] [<c011b73c>] ? default_wake_function+0x0/0x8
[ 978.033743] [<c011b73c>] ? default_wake_function+0x0/0x8
[ 978.033743] [<c011b73c>] ? default_wake_function+0x0/0x8
[ 978.033743] [<c011b73c>] ? default_wake_function+0x0/0x8
[ 978.033743] [<c011b73c>] ? default_wake_function+0x0/0x8
[ 978.033743] [<c011b73c>] ? default_wake_function+0x0/0x8
[ 978.033743] [<c011b73c>] ? default_wake_function+0x0/0x8
[ 978.033743] [<c011b73c>] ? default_wake_function+0x0/0x8
[ 978.033743] [<c011b73c>] ? default_wake_function+0x0/0x8
[ 978.033743] [<c0136198>] ? getnstimeofday+0x37/0xbc
[ 978.033743] [<c017f334>] ? sys_poll+0x3b/0x6e
[ 978.033743] [<c0103857>] ? sysenter_past_esp+0x78/0xb1
[ 978.033743] =======================
[ 2388.570877] hda: dma_timer_expiry: dma status == 0x21
[ 2399.059397] hda: DMA timeout error
[ 2399.379295] hda: dma timeout error: status=0xd8 { Busy }
[ 2399.379295] ide: failed opcode was: unknown
[ 2399.379295] hda: DMA disabled
[ 2399.440265] ide0: reset: success
** Model information
not available
** Loaded modules:
Module Size Used by
ppdev 6468 0
lp 8164 0
ipv6 235396 18
cpufreq_ondemand 6476 0
cpufreq_stats 3776 0
freq_table 4224 2 cpufreq_ondemand,cpufreq_stats
cpufreq_userspace 3172 0
cpufreq_powersave 1856 0
cpufreq_conservative 5960 0
loop 12748 0
parport_pc 22500 1
parport 30988 3 ppdev,lp,parport_pc
pcspkr 2432 0
psmouse 32336 0
serio_raw 4740 0
button 6096 0
i2c_piix4 7216 0
i2c_core 19828 1 i2c_piix4
joydev 8480 0
evdev 8000 2
usbhid 35872 0
hid 33184 1 usbhid
ff_memless 4392 1 usbhid
ext3 105576 1
jbd 39476 1 ext3
mbcache 7108 1 ext3
ide_cd_mod 27684 0
cdrom 30176 1 ide_cd_mod
ide_disk 10496 3
ata_generic 4676 0
libata 140448 1 ata_generic
scsi_mod 129548 1 libata
8139too 20384 0
dock 8304 1 libata
floppy 47844 0
8139cp 16800 0
mii 4896 2 8139too,8139cp
uhci_hcd 18672 0
piix 6568 0 [permanent]
ide_pci_generic 3908 0 [permanent]
usbcore 118224 3 usbhid,uhci_hcd
ide_core 96168 4 ide_cd_mod,ide_disk,piix,ide_pci_generic
thermal 15228 0
processor 32576 1 thermal
fan 4196 0
thermal_sys 10856 3 thermal,processor,fan
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 440FX - 82441FX PMC [Natoma]
[8086:1237] (rev 02)
Subsystem: Qumranet, Inc. Device [1af4:1100]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:01.0 ISA bridge [0601]: Intel Corporation 82371SB PIIX3 ISA [Natoma/Triton
II] [8086:7000]
Subsystem: Qumranet, Inc. Device [1af4:1100]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:01.1 IDE interface [0101]: Intel Corporation 82371SB PIIX3 IDE
[Natoma/Triton II] [8086:7010] (prog-if 80 [Master])
Subsystem: Qumranet, Inc. Device [1af4:1100]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[size=1]
Region 4: I/O ports at c000 [size=16]
Kernel driver in use: PIIX_IDE
Kernel modules: piix
00:01.2 USB Controller [0c03]: Intel Corporation 82371SB PIIX3 USB
[Natoma/Triton II] [8086:7020] (rev 01) (prog-if 00 [UHCI])
Subsystem: Qumranet, Inc. Device [1af4:1100]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at c020 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:01.3 Bridge [0680]: Intel Corporation 82371AB/EB/MB PIIX4 ACPI [8086:7113]
(rev 03)
Subsystem: Qumranet, Inc. Device [1af4:1100]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 9
Kernel driver in use: piix4_smbus
Kernel modules: i2c-piix4
00:02.0 VGA compatible controller [0300]: Cirrus Logic GD 5446 [1013:00b8]
(prog-if 00 [VGA controller])
Subsystem: Qumranet, Inc. Device [1af4:1100]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=32M]
Region 1: Memory at f2000000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at f2010000 [disabled] [size=64K]
Kernel modules: cirrusfb
00:03.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ [10ec:8139] (rev 20)
Subsystem: Qumranet, Inc. Device [1af4:1100]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at c100 [size=256]
Region 1: Memory at f2020000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at f2030000 [disabled] [size=64K]
Kernel driver in use: 8139cp
Kernel modules: 8139cp, 8139too
** Sound cards:
-- System Information:
Debian Release: 5.0.5
APT prefers stable
APT policy: (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 2.6.26-2-686 (SMP w/2 CPU cores)
Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-2-686 depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92o tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.26-2-686 recommends:
ii libc6-i686 2.7-18lenny4 GNU C Library: Shared libraries [i
Versions of packages linux-image-2.6.26-2-686 suggests:
ii grub 0.97-47lenny2 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.26 <none> (no description available)
Versions of packages linux-image-2.6.26-2-686 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
-- debconf information:
linux-image-2.6.26-2-686/postinst/bootloader-error-2.6.26-2-686:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.26-2-686/postinst/old-dir-initrd-link-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/overwriting-modules-2.6.26-2-686: true
linux-image-2.6.26-2-686/postinst/bootloader-test-error-2.6.26-2-686:
linux-image-2.6.26-2-686/postinst/depmod-error-2.6.26-2-686: false
linux-image-2.6.26-2-686/preinst/bootloader-initrd-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/abort-overwrite-2.6.26-2-686:
linux-image-2.6.26-2-686/preinst/abort-install-2.6.26-2-686:
linux-image-2.6.26-2-686/postinst/depmod-error-initrd-2.6.26-2-686: false
linux-image-2.6.26-2-686/postinst/create-kimage-link-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/failed-to-move-modules-2.6.26-2-686:
linux-image-2.6.26-2-686/preinst/initrd-2.6.26-2-686:
linux-image-2.6.26-2-686/preinst/lilo-has-ramdisk:
linux-image-2.6.26-2-686/prerm/would-invalidate-boot-loader-2.6.26-2-686: true
linux-image-2.6.26-2-686/postinst/kimage-is-a-directory:
linux-image-2.6.26-2-686/postinst/old-initrd-link-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/elilo-initrd-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/lilo-initrd-2.6.26-2-686: true
linux-image-2.6.26-2-686/prerm/removing-running-kernel-2.6.26-2-686: true
linux-image-2.6.26-2-686/postinst/old-system-map-link-2.6.26-2-686: true
--- End Message ---
--- Begin Message ---
Source: user-mode-linux
Source-Version: 2.6.26-1um-2+24lenny1
We believe that the bug you reported is fixed in the latest version of
user-mode-linux, which is due to be installed in the Debian FTP archive:
user-mode-linux_2.6.26-1um-2+24lenny1.diff.gz
to main/u/user-mode-linux/user-mode-linux_2.6.26-1um-2+24lenny1.diff.gz
user-mode-linux_2.6.26-1um-2+24lenny1.dsc
to main/u/user-mode-linux/user-mode-linux_2.6.26-1um-2+24lenny1.dsc
user-mode-linux_2.6.26-1um-2+24lenny1_i386.deb
to main/u/user-mode-linux/user-mode-linux_2.6.26-1um-2+24lenny1_i386.deb
A summary of the changes between this version and the previous one is
attached.
Thank you for reporting the bug, which will now be closed. If you
have further comments please address them to 589...@bugs.debian.org,
and the maintainer will reopen the bug report if appropriate.
Debian distribution maintenance software
pp.
dann frazier <da...@debian.org> (supplier of updated user-mode-linux package)
(This message was generated automatically at their request; if you
believe that there is a problem with it please contact the archive
administrators by mailing ftpmas...@debian.org)
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Format: 1.8
Date: Thu, 19 Aug 2010 18:02:50 -0600
Source: user-mode-linux
Binary: user-mode-linux
Architecture: source i386
Version: 2.6.26-1um-2+24lenny1
Distribution: stable-security
Urgency: high
Maintainer: User Mode Linux Maintainers <pkg-uml-p...@lists.alioth.debian.org>
Changed-By: dann frazier <da...@debian.org>
Description:
user-mode-linux - User-mode Linux (kernel)
Closes: 589179
Changes:
user-mode-linux (2.6.26-1um-2+24lenny1) stable-security; urgency=high
.
* Rebuild against linux-source-2.6.26 (2.6.26-24):
* cifs: Fix a kernel BUG with remote OS/2 server (CVE-2010-2248)
* Fix race in tty_fasync() properly (CVE-2009-4895)
* xfs: prevent swapext from operating on write-only files (CVE-2010-2226)
* nfsd4: bug in read_buf (CVE-2010-2521)
* GFS2: rename causes kernel Oops (CVE-2010-2798)
* exec: Fix 'flush_old_exec()/setup_new_exec()' split (Closes: #589179;
regression due to fix for CVE-2010-0307)
* can: add limit for nframes and clean up signed/unsigned variables
(CVE-REQUESTED)
* mm: keep a guard page below a grow-down stack segment (CVE-2010-2240)
* drm: stop information leak of old kernel stack (CVE-2010-2803)
* ext4: fix integer overflows in ext4_ext_{in_cache,get_blocks}
(CVE-2010-3015)
Checksums-Sha1:
4553192cf8f37f15e1612c1acf8ee4472859b0c4 1273
user-mode-linux_2.6.26-1um-2+24lenny1.dsc
a5a1f92939dec98c72d54afa41a431973eac27cb 19079
user-mode-linux_2.6.26-1um-2+24lenny1.diff.gz
1ecb221248d1abc867ff0f93bc5480418cd7f0c7 5363312
user-mode-linux_2.6.26-1um-2+24lenny1_i386.deb
Checksums-Sha256:
d6eaff08e58b83d9853e9d8f6fb5ed5efaf39ae5cd5b551b94166ec1e1a55b4b 1273
user-mode-linux_2.6.26-1um-2+24lenny1.dsc
f3d83bc048830a2bed7c3235f0e1506249c64b22f3c599731b77e2aa17dd4176 19079
user-mode-linux_2.6.26-1um-2+24lenny1.diff.gz
dcf2238ac5f2c35574d1cc951e6200729a689180d957bdd6eec190d38062cf5a 5363312
user-mode-linux_2.6.26-1um-2+24lenny1_i386.deb
Files:
29deed5d80bee626c9dbce7dae8ac04a 1273 misc extra
user-mode-linux_2.6.26-1um-2+24lenny1.dsc
b16b61a6303306a84369f2a9c8a5950e 19079 misc extra
user-mode-linux_2.6.26-1um-2+24lenny1.diff.gz
3f5c8ceb48dba2d84999c994f2820e8e 5363312 misc extra
user-mode-linux_2.6.26-1um-2+24lenny1_i386.deb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iD8DBQFMbdKkhuANDBmkLRkRAvdRAJ4onEDIsGdicVlnEUO+90mnR2ODpQCeIHtq
V7zQCXm9RiQalP0fSzW4Fto=
=va94
-----END PGP SIGNATURE-----
--- End Message ---
