--- Begin Message ---
Package: linux-image-2.6.26-2-686
Version: 2.6.26-15
Severity: normal
I have a IEEE 802.11 Wireless PCI Adapter, which uses the Relatek
RTL-8185 chipset. If I'm not mistaken the card is suppose to work with
the rtl8180 kernel module.
The module rtl8180 loads at boot time and recognizes my card. The
problem is that I see my wireless access point with very low intencity
and I am often unable to get a connection at all. Its not a problem with
range because I actually have my router and wifi cards practially
touching each other. Note I am using wicd.
I got the card working by using ndiswrapper. It works flawlessly now.
The card used to work a few months ago with rtl8180 in Debian Lenny. I
don't remember the kernel version I used at the time. I stopped
connecting through wireless for a long time so it is possible that the
module broke some time ago and I never noticed.
-- Package-specific info:
** Version:
Linux version 2.6.26-2-686 (Debian 2.6.26-15) (da...@debian.org) (gcc version
4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Thu Mar 26 01:08:11 UTC
2009
** Command line:
root=/dev/sda2 ro
** Tainted: P (1)
** Kernel log:
[ 4.212121] ata1.00: ATA-7: ST3160812AS, 3.AHL, max UDMA/100
[ 4.212166] ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 4.228120] ata1.00: configured for UDMA/100
[ 4.558259] ata2: SATA link down (SStatus 0 SControl 300)
[ 4.558398] scsi 0:0:0:0: Direct-Access ATA ST3160812AS 3.AH
PQ: 0 ANSI: 5
[ 4.564013] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI)
Driver
[ 4.564013] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 20
[ 4.564013] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 20
(level, low) -> IRQ 20
[ 4.564013] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 4.564013] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 4.564013] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus
number 2
[ 4.564013] ohci_hcd 0000:00:02.0: irq 20, io mem 0xfe02f000
[ 4.565358] udev: renamed network interface eth0 to eth1
[ 4.598271] Initializing USB Mass Storage driver...
[ 4.598402] scsi2 : SCSI emulation for USB Mass Storage devices
[ 4.598516] usbcore: registered new interface driver usb-storage
[ 4.598563] USB Mass Storage support registered.
[ 4.598690] usb-storage: device found at 2
[ 4.598692] usb-storage: waiting for device to settle before scanning
[ 4.618098] usb usb2: configuration #1 chosen from 1 choice
[ 4.618172] hub 2-0:1.0: USB hub found
[ 4.618221] hub 2-0:1.0: 8 ports detected
[ 4.720105] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.720155] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 4.720214] usb usb2: Product: OHCI Host Controller
[ 4.720257] usb usb2: Manufacturer: Linux 2.6.26-2-686 ohci_hcd
[ 4.720302] usb usb2: SerialNumber: 0000:00:02.0
[ 4.731266] hda: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
[ 4.731456] Uniform CD-ROM driver Revision: 3.20
[ 4.769544] Driver 'sd' needs updating - please use bus_type methods
[ 4.769698] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 4.769762] sd 0:0:0:0: [sda] Write Protect is off
[ 4.769806] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.769836] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 4.769955] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 4.770016] sd 0:0:0:0: [sda] Write Protect is off
[ 4.770060] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.770089] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 4.770153] sda: sda1 sda2 sda3 < sda5 sda6 >
[ 4.788012] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.252501] PM: Starting manual resume from disk
[ 6.948444] udev: starting version 141
[ 6.948521] udev: deprecated sysfs layout; update the kernel or disable
CONFIG_SYSFS_DEPRECATED; some udev features will not work correctly
[ 7.742649] input: PC Speaker as /class/input/input1
[ 8.114719] input: Power Button (FF) as /class/input/input2
[ 8.119241] ACPI: Power Button (FF) [PWRF]
[ 8.119352] input: Power Button (CM) as /class/input/input3
[ 8.129716] ACPI: Power Button (CM) [PWRB]
[ 8.217420] ndiswrapper version 1.54 loaded (smp=yes, preempt=no)
[ 8.301890] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x1c00
[ 8.301958] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x1c40
[ 8.372012] input: ImPS/2 Generic Wheel Mouse as /class/input/input4
[ 8.372012] ndiswrapper: driver net8185
(Realtek,11/22/2006,5.1094.1122.2006) loaded
[ 8.372012] ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
[ 8.372012] ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC2] -> GSI 17
(level, low) -> IRQ 17
[ 8.644827] ndiswrapper: using IRQ 17
[ 9.596180] usb-storage: device scan complete
[ 9.602665] scsi 2:0:0:0: Direct-Access Generic- Compact Flash 1.00
PQ: 0 ANSI: 0 CCS
[ 9.609135] scsi 2:0:0:1: Direct-Access Generic- SM/xD-Picture 1.00
PQ: 0 ANSI: 0 CCS
[ 9.615901] scsi 2:0:0:2: Direct-Access Generic- SD/MMC 1.00
PQ: 0 ANSI: 0 CCS
[ 9.622654] scsi 2:0:0:3: Direct-Access Generic- MS/MS-Pro 1.00
PQ: 0 ANSI: 0 CCS
[ 9.626470] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 9.629257] sd 2:0:0:1: [sdc] Attached SCSI removable disk
[ 9.633458] sd 2:0:0:2: [sdd] Attached SCSI removable disk
[ 9.637193] sd 2:0:0:3: [sde] Attached SCSI removable disk
[ 14.984330] wlan0: ethernet device 00:06:4f:70:f2:d2 using NDIS driver:
net8185, version: 0x50446, NDIS version: 0x500, vendor: 'Realtek RTL8185
Wireless LAN (Mini-)PCI NIC ',
10EC:8185.5.conf
[ 14.984556] wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2,
WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK
[ 14.984820] usbcore: registered new interface driver ndiswrapper
[ 14.985749] ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 23
[ 14.985800] ACPI: PCI Interrupt 0000:00:05.0[B] -> Link [AAZA] -> GSI 23
(level, low) -> IRQ 23
[ 14.985927] PCI: Setting latency timer of device 0000:00:05.0 to 64
[ 15.018772] hda_codec: Unknown model for ALC883, trying auto-probe from
BIOS...
[ 15.968020] Adding 2650684k swap on /dev/sda5. Priority:-1 extents:1
across:2650684k
[ 17.072136] loop: module loaded
[ 17.324029] kjournald starting. Commit interval 5 seconds
[ 17.324029] EXT3-fs warning: mounting unchecked fs, running e2fsck is
recommended
[ 17.324029] EXT3 FS on sda6, internal journal
[ 17.324029] EXT3-fs: mounted filesystem with ordered data mode.
[ 18.643920] RPC: Registered udp transport module.
[ 18.643981] RPC: Registered tcp transport module.
[ 18.695426] Installing knfsd (copyright (C) 1996 o...@monad.swb.de).
[ 20.778270] NET: Registered protocol family 10
[ 20.778827] lo: Disabled Privacy Extensions
[ 21.138727] lp: driver loaded but no devices found
[ 21.164193] ppdev: user-space parallel port driver
[ 23.148887] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery
directory
[ 23.164010] NFSD: starting 90-second grace period
[ 25.852008] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 28.269468] Bluetooth: Core ver 2.11
[ 28.270712] NET: Registered protocol family 31
[ 28.270763] Bluetooth: HCI device and connection manager initialized
[ 28.270811] Bluetooth: HCI socket layer initialized
[ 28.285888] Bluetooth: L2CAP ver 2.9
[ 28.285937] Bluetooth: L2CAP socket layer initialized
[ 28.346673] Bluetooth: RFCOMM socket layer initialized
[ 28.346736] Bluetooth: RFCOMM TTY layer initialized
[ 28.346780] Bluetooth: RFCOMM ver 1.8
[ 39.596012] eth1: no IPv6 routers present
[ 181.015066] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 191.568023] wlan0: no IPv6 routers present
** Loaded modules:
Module Size Used by
binfmt_misc 7528 1
rfcomm 28272 2
l2cap 17248 9 rfcomm
bluetooth 44868 4 rfcomm,l2cap
ppdev 6500 0
parport_pc 22500 0
lp 8164 0
parport 30988 3 ppdev,parport_pc,lp
ipv6 235364 14
nfsd 186672 17
auth_rpcgss 33952 1 nfsd
exportfs 3904 1 nfsd
nfs 214024 0
lockd 54568 2 nfsd,nfs
nfs_acl 2912 2 nfsd,nfs
sunrpc 162464 15 nfsd,auth_rpcgss,nfs,lockd,nfs_acl
ext3 105512 1
jbd 39444 1 ext3
dm_snapshot 14340 0
loop 12748 0
snd_hda_intel 325688 1
snd_pcm_oss 32832 0
snd_mixer_oss 12320 1 snd_pcm_oss
snd_pcm 62596 2 snd_hda_intel,snd_pcm_oss
snd_seq_dummy 2660 0
snd_seq_oss 24992 0
snd_seq_midi 5728 0
snd_rawmidi 18528 1 snd_seq_midi
snd_seq_midi_event 6432 2 snd_seq_oss,snd_seq_midi
snd_seq 41456 6
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 17800 2 snd_pcm,snd_seq
snd_seq_device 6380 5
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
k8temp 4064 0
snd 45604 11
snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
soundcore 6368 1 snd
snd_page_alloc 7816 2 snd_hda_intel,snd_pcm
i2c_nforce2 5536 0
ndiswrapper 152732 0
i2c_core 19828 1 i2c_nforce2
button 6096 0
serio_raw 4740 0
pcspkr 2432 0
psmouse 32336 0
evdev 8000 3
ext2 54504 1
mbcache 7108 2 ext3,ext2
sd_mod 22200 4
ide_cd_mod 27652 0
cdrom 30176 1 ide_cd_mod
ide_pci_generic 3908 0 [permanent]
usb_storage 77024 0
ata_generic 4676 0
ohci_hcd 18500 0
sata_nv 19240 3
libata 140416 2 ata_generic,sata_nv
scsi_mod 129324 3 sd_mod,usb_storage,libata
dock 8304 1 libata
forcedeth 45072 0
amd74xx 7720 0 [permanent]
ide_core 96136 3 ide_cd_mod,ide_pci_generic,amd74xx
ehci_hcd 28396 0
usbcore 118224 5 ndiswrapper,usb_storage,ohci_hcd,ehci_hcd
thermal 15228 0
processor 32544 1 thermal
fan 4164 0
thermal_sys 10856 3 thermal,processor,fan
dm_mirror 15104 0
dm_log 8484 1 dm_mirror
dm_mod 46184 3 dm_snapshot,dm_mirror,dm_log
** PCI devices:
00:00.0 RAM memory [0500]: nVidia Corporation MCP61 Memory Controller
[10de:03ea] (rev a1)
Subsystem: Hewlett-Packard Company Device [103c:2a4d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:01.0 ISA bridge [0601]: nVidia Corporation MCP61 LPC Bridge [10de:03e0] (rev
a2)
Subsystem: Hewlett-Packard Company Device [103c:2a4d]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
00:01.1 SMBus [0c05]: nVidia Corporation MCP61 SMBus [10de:03eb] (rev a2)
Subsystem: Hewlett-Packard Company Device [103c:2a4d]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at fc00 [size=64]
Region 4: I/O ports at 1c00 [size=64]
Region 5: I/O ports at 1c40 [size=64]
Capabilities: <access denied>
Kernel driver in use: nForce2_smbus
00:01.2 RAM memory [0500]: nVidia Corporation MCP61 Memory Controller
[10de:03f5] (rev a2)
Subsystem: Hewlett-Packard Company Device [103c:2a4d]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:02.0 USB Controller [0c03]: nVidia Corporation MCP61 USB Controller
[10de:03f1] (rev a2) (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Device [103c:2a4d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 20
Region 0: Memory at fe02f000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
00:02.1 USB Controller [0c03]: nVidia Corporation MCP61 USB Controller
[10de:03f2] (rev a2) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Device [103c:2a4d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 23
Region 0: Memory at fe02e000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:04.0 PCI bridge [0604]: nVidia Corporation MCP61 PCI bridge [10de:03f3] (rev
a1) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fdf00000-fdffffff
Prefetchable memory behind bridge: fd800000-fd8fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:05.0 Audio device [0403]: nVidia Corporation MCP61 High Definition Audio
[10de:03f0] (rev a2)
Subsystem: Hewlett-Packard Company Device [103c:2a4d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin B routed to IRQ 23
Region 0: Memory at fe028000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
00:06.0 IDE interface [0101]: nVidia Corporation MCP61 IDE [10de:03ec] (rev a2)
(prog-if 8a [Master SecP PriP])
Subsystem: Hewlett-Packard Company Device [103c:2a4d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[size=1]
Region 4: I/O ports at f000 [size=16]
Capabilities: <access denied>
Kernel driver in use: AMD_IDE
00:07.0 Bridge [0680]: nVidia Corporation MCP61 Ethernet [10de:03ef] (rev a2)
Subsystem: Hewlett-Packard Company Device [103c:2a4d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 220
Region 0: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at ec00 [size=8]
Capabilities: <access denied>
Kernel driver in use: forcedeth
00:08.0 IDE interface [0101]: nVidia Corporation MCP61 SATA Controller
[10de:03f6] (rev a2) (prog-if 85 [Master SecO PriO])
Subsystem: Hewlett-Packard Company Device [103c:2a4d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at 09f0 [size=8]
Region 1: I/O ports at 0bf0 [size=4]
Region 2: I/O ports at 0970 [size=8]
Region 3: I/O ports at 0b70 [size=4]
Region 4: I/O ports at d800 [size=16]
Region 5: Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: sata_nv
00:09.0 PCI bridge [0604]: nVidia Corporation MCP61 PCI Express bridge
[10de:03e8] (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fde00000-fdefffff
Prefetchable memory behind bridge: 00000000fdd00000-00000000fddfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:0b.0 PCI bridge [0604]: nVidia Corporation MCP61 PCI Express bridge
[10de:03e9] (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: fdc00000-fdcfffff
Prefetchable memory behind bridge: 00000000fdb00000-00000000fdbfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:0c.0 PCI bridge [0604]: nVidia Corporation MCP61 PCI Express bridge
[10de:03e9] (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: fda00000-fdafffff
Prefetchable memory behind bridge: 00000000fd900000-00000000fd9fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:0d.0 VGA compatible controller [0300]: nVidia Corporation GeForce 6100
nForce 420 [10de:03d5] (rev a2) (prog-if 00 [VGA controller])
Subsystem: Hewlett-Packard Company Device [103c:2a4d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 7
Region 0: Memory at fb000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at fc000000 (64-bit, non-prefetchable) [size=16M]
[virtual] Expansion ROM at 50000000 [disabled] [size=128K]
Capabilities: <access denied>
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Kernel driver in use: k8temp
01:08.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8185
IEEE 802.11a/b/g Wireless LAN Controller [10ec:8185] (rev 20)
Subsystem: Realtek Semiconductor Co., Ltd. RTL-8185 IEEE 802.11a/b/g
Wireless LAN Controller [10ec:8185]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (8000ns min, 16000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at cc00 [size=256]
Region 1: Memory at fdfff000 (32-bit, non-prefetchable) [size=512]
Capabilities: <access denied>
Kernel driver in use: ndiswrapper
-- System Information:
Debian Release: squeeze/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 2.6.26-2-686 (SMP w/1 CPU core)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-2-686 depends on:
ii debconf [debconf-2.0] 1.5.26 Debian configuration management sy
ii initramfs-tools [linux-initra 0.93.2 tools for generating an initramfs
ii module-init-tools 3.7-pre9-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.26-2-686 recommends:
ii libc6-i686 2.9-4 GNU C Library: Shared libraries [i
Versions of packages linux-image-2.6.26-2-686 suggests:
ii grub 0.97-53 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.26 <none> (no description available)
-- debconf information:
linux-image-2.6.26-2-686/postinst/bootloader-error-2.6.26-2-686:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.26-2-686/postinst/old-dir-initrd-link-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/overwriting-modules-2.6.26-2-686: true
linux-image-2.6.26-2-686/postinst/bootloader-test-error-2.6.26-2-686:
linux-image-2.6.26-2-686/postinst/depmod-error-2.6.26-2-686: false
linux-image-2.6.26-2-686/preinst/bootloader-initrd-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/abort-overwrite-2.6.26-2-686:
linux-image-2.6.26-2-686/preinst/abort-install-2.6.26-2-686:
linux-image-2.6.26-2-686/postinst/depmod-error-initrd-2.6.26-2-686: false
linux-image-2.6.26-2-686/postinst/create-kimage-link-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/failed-to-move-modules-2.6.26-2-686:
linux-image-2.6.26-2-686/preinst/initrd-2.6.26-2-686:
linux-image-2.6.26-2-686/preinst/lilo-has-ramdisk:
linux-image-2.6.26-2-686/prerm/would-invalidate-boot-loader-2.6.26-2-686: true
linux-image-2.6.26-2-686/postinst/kimage-is-a-directory:
linux-image-2.6.26-2-686/postinst/old-initrd-link-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/elilo-initrd-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/lilo-initrd-2.6.26-2-686: true
linux-image-2.6.26-2-686/prerm/removing-running-kernel-2.6.26-2-686: true
linux-image-2.6.26-2-686/postinst/old-system-map-link-2.6.26-2-686: true
--- End Message ---
