I've got 2 different intel Boards, both with squeeze ( kernel 2.6.32 AMD) and pci 10ec:8180 (rtl8180 wireless-G PCI Adapter ENLWI-G2 from Encore). In one board, DG33BU, wireless works fine since lenny. On the other one, DG31PR, it happens what is described below for the kernel 2.6.26. I've check exchanging the wireless boards and it happens the same. Both motherboards, running Windows XP, connect with AP.
On Tue, Feb 23, 2010 at 3:38 PM, Moritz Muehlenhoff <j...@inutil.org> wrote: > On Mon, Nov 03, 2008 at 05:28:06AM -0500, > reportbugimage261486.to.pee...@spamgourmet.com wrote: >> Package: linux-image-2.6.26-1-486 >> Version: 2.6.26-8 >> Severity: normal >> >> >> On a clean lenny install on my acer aspire 1350, the built-in realtek >> wireless with pci id 10ec:8180 won't connect with linux driver. It does >> scan lots of APs though. >> >> Eg: >> >> Cell 03 - Address: 00:50:18:32:F6:6C >> ESSID:"default" >> Mode:Master >> Channel:11 >> Frequency:2.462 GHz (Channel 11) >> Signal level=-130 dBm >> Encryption key:off >> Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s >> 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s >> 48 Mb/s; 54 Mb/s >> Extra:tsf=00000001cfec119a >> >> Running these commands: >> >> ifconfig wlan0 down >> dhclient -r wlan0 >> >> iwconfig wlan0 ap 00:50:18:32:F6:6C essid default mode managed key open >> ifconfig wlan0 192.168.123.161 up >> >> gives me this in dmesg: >> >> [ 7722.416251] ADDRCONF(NETDEV_UP): wlan0: link is not ready >> [ 7722.428055] wlan0: Initial auth_alg=0 >> [ 7722.428073] wlan0: authenticate with AP 00:50:18:32:f6:6c >> [ 7722.628053] wlan0: authenticate with AP 00:50:18:32:f6:6c >> [ 7722.828053] wlan0: authenticate with AP 00:50:18:32:f6:6c >> [ 7723.028057] wlan0: authentication with AP 00:50:18:32:f6:6c timed out >> >> Immediately after the iwconfig configuration command is run, iwconfig >> shows this status: >> >> wmaster0 no wireless extensions. >> >> wlan0 IEEE 802.11 ESSID:"default" >> Mode:Managed Frequency:2.462 GHz Access Point: Not-Associated >> Tx-Power=20 dBm >> Retry min limit:7 RTS thr:off Fragment thr=2352 B >> Encryption key:off >> Link Quality:0 Signal level:0 Noise level:0 >> Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 >> Tx excessive retries:0 Invalid misc:0 Missed beacon:0 >> >> >> The iwconfig status report above does not change, even though scanning >> works. >> >> Other machines connect to the AP ok. >> >> That's the end of my personal report input. Reportbug dumps follow... > > Please test the 2.6.32 kernel, it installs fine in testing. > > Cheers, > Moritz > > > > -- > To unsubscribe, send mail to 504386-unsubscr...@bugs.debian.org. > -- To UNSUBSCRIBE, email to debian-kernel-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org Archive: http://lists.debian.org/4244525c1002231145l3e3bd9e7s433b158eec47d...@mail.gmail.com
