--- Begin Message ---
Package: linux-2.6
Version: 2.6.31-1
Severity: important
Hello,
When I start the kernel 2.6.31, the wifi does not start, while it runs
correctly with the kernel 2.6.30.
It seems that the wireless parameters of /etc/network/interfaces are not
given to the script /etc/network/if-pre-up.d/wireless-tools.
As you may see in the kernel log, wlan0 is 'not ready' at system startup
time. Looking at the device by iwconfig shows empty values but scanning
by iwlist works correctly.
To make the device work, I must set manually the iwconfig parameters:
# iwconfig wlan0 essid moine mode managed enc ...
and then start the dhcp client (both dhclient3 and dhcpcd give the same
results).
If I try to set down and then up the device, I get:
- down
r...@tele:/home/jef# ifdown -v wlan0
Configuring interface wlan0=wlan0 (inet)
run-parts --verbose /etc/network/if-down.d
dhcpcd -k wlan0
ifconfig wlan0 down
run-parts --verbose /etc/network/if-post-down.d
run-parts: executing /etc/network/if-post-down.d/wireless-tools
Error for wireless request "Set Mode" (8B06) :
SET failed on device wlan0 ; Invalid argument.
- up
r...@tele:/home/jef# ifup -v wlan0
Configuring interface wlan0=wlan0 (inet)
run-parts --verbose /etc/network/if-pre-up.d
run-parts: executing /etc/network/if-pre-up.d/wireless-tools
dhcpcd wlan0
err, wlan0: timed out
warn, wlan0: using IPV4LL address 169.254.12.77
run-parts --verbose /etc/network/if-up.d
run-parts: executing /etc/network/if-up.d/mountnfs
dhcpcd.sh: interface wlan0 has been configured with new IP=169.254.12.77
and iwconfig shows empty values.
I am not new to Linux, but I could not find how the kernel might change
the scanning of the configuration file!
Regards.
-- Package-specific info:
** Version:
Linux version 2.6.31-1-amd64 (Debian 2.6.31-1) (wa...@debian.org) (gcc version
4.3.4 (Debian 4.3.4-5) ) #1 SMP Sat Oct 24 17:50:31 UTC 2009
** Command line:
root=/dev/sda3 ro
** Not tainted
** Kernel log:
[ 4.471076] ACPI: Power Button [PWRF]
[ 4.471208] input: Power Button as
/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3
[ 4.471260] ACPI: Power Button [PWRB]
[ 4.486250] ACPI: WMI: Mapper loaded
[ 4.563771] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 4.731341] EDAC MC: Ver: 2.1.0 Oct 24 2009
[ 4.735285] k8temp 0000:00:18.3: Temperature readouts might be wrong - check
erratum #141
[ 4.771345] EDAC amd64_edac: Ver: 3.2.0 Oct 24 2009
[ 4.771635] EDAC amd64: This node reports that Memory ECC is currently
disabled.
[ 4.771688] EDAC amd64: bit 0x400000 in register F3x44 of the MISC_CONTROL
device (0000:00:18.3) should be enabled
[ 4.771742] EDAC amd64: WARNING: ECC is NOT currently enabled by the BIOS.
Module will NOT be loaded.
[ 4.771744] Either Enable ECC in the BIOS, or use the
'ecc_enable_override' parameter.
[ 4.771745] Might be a BIOS bug, if BIOS says ECC is enabled
[ 4.771747] Use of the override can cause unknown side effects.
[ 4.771935] amd64_edac: probe of 0000:00:18.2 failed with error -22
[ 4.869786] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x2d00
[ 4.869849] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x2e00
[ 4.960033] Initializing USB Mass Storage driver...
[ 4.960433] scsi4 : SCSI emulation for USB Mass Storage devices
[ 4.960589] usb-storage: device found at 2
[ 4.960593] usb-storage: waiting for device to settle before scanning
[ 4.960602] usbcore: registered new interface driver usb-storage
[ 4.960643] USB Mass Storage support registered.
[ 5.029065] cfg80211: Using static regulatory domain info
[ 5.029107] cfg80211: Regulatory domain: US
[ 5.029144] (start_freq - end_freq @ bandwidth), (max_antenna_gain,
max_eirp)
[ 5.029194] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
[ 5.029235] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 5.029275] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 5.029316] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 5.029356] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 5.029396] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
[ 5.029443] cfg80211: Calling CRDA for country: US
[ 5.188525] input: ImPS/2 Generic Wheel Mouse as
/devices/platform/i8042/serio1/input/input5
[ 5.351562] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 21
[ 5.351608] HDA Intel 0000:00:07.0: PCI INT A -> Link[LAZA] -> GSI 21
(level, low) -> IRQ 21
[ 5.351708] HDA Intel 0000:00:07.0: setting latency timer to 64
[ 5.940013] hda_codec: Unknown model for ALC888, trying auto-probe from
BIOS...
[ 5.956100] input: HDA Digital PCBeep as
/devices/pci0000:00/0000:00:07.0/input/input6
[ 6.021172] phy0: Selected rate control algorithm 'minstrel'
[ 6.021813] Registered led device: rt73usb-phy0::radio
[ 6.021870] Registered led device: rt73usb-phy0::assoc
[ 6.021924] Registered led device: rt73usb-phy0::quality
[ 6.022877] usbcore: registered new interface driver rt73usb
[ 6.038416] usbcore: registered new interface driver rt2500usb
[ 6.955413] Adding 2000052k swap on /dev/sda5. Priority:-1 extents:1
across:2000052k
[ 7.104807] EXT3 FS on sda3, internal journal
[ 7.657103] kjournald starting. Commit interval 5 seconds
[ 7.657370] EXT3 FS on sda6, internal journal
[ 7.657429] EXT3-fs: mounted filesystem with ordered data mode.
[ 8.182962] rt73usb 1-1:1.0: firmware: requesting rt73.bin
[ 8.300001] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 9.958084] usb-storage: device scan complete
[ 9.965049] scsi 4:0:0:0: Direct-Access Generic USB SD Reader 1.00
PQ: 0 ANSI: 0
[ 9.972039] scsi 4:0:0:1: Direct-Access Generic USB CF Reader 1.01
PQ: 0 ANSI: 0
[ 9.979038] scsi 4:0:0:2: Direct-Access Generic USB SM Reader 1.02
PQ: 0 ANSI: 0
[ 9.986038] scsi 4:0:0:3: Direct-Access Generic USB MS Reader 1.03
PQ: 0 ANSI: 0
[ 10.019053] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[ 10.129091] sd 4:0:0:2: [sdd] Attached SCSI removable disk
[ 10.151051] sd 4:0:0:1: [sdc] Attached SCSI removable disk
[ 10.162036] sd 4:0:0:3: [sde] Attached SCSI removable disk
[ 170.627981] wlan0: authenticate with AP 00:07:cb:58:be:fb
[ 170.629982] wlan0: authenticated
[ 170.629985] wlan0: associate with AP 00:07:cb:58:be:fb
[ 170.632102] wlan0: RX AssocResp from 00:07:cb:58:be:fb (capab=0x411 status=0
aid=1)
[ 170.632106] wlan0: associated
[ 170.644725] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 181.296010] wlan0: no IPv6 routers present
[ 5138.323751] alloc irq_desc for 31 on node 0
[ 5138.323755] alloc kstat_irqs on node 0
[ 5138.323768] forcedeth 0000:00:0a.0: irq 31 for MSI/MSI-X
[ 5138.323971] eth0: no link during initialization.
[ 5138.324685] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 5603.697038] wlan0: deauthenticating by local choice (reason=3)
[ 5618.934365] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 6314.306231] wlan0: authenticate with AP 00:07:cb:58:be:fb
[ 6314.308103] wlan0: authenticated
[ 6314.308106] wlan0: associate with AP 00:07:cb:58:be:fb
[ 6314.310236] wlan0: RX AssocResp from 00:07:cb:58:be:fb (capab=0x411 status=0
aid=1)
[ 6314.310240] wlan0: associated
[ 6314.322972] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 6325.264011] wlan0: no IPv6 routers present
[ 6446.540028] wlan0: deauthenticating by local choice (reason=3)
[ 6451.430620] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 6484.650106] wlan0: authenticate with AP 00:07:cb:58:be:fb
[ 6484.651978] wlan0: authenticated
[ 6484.651981] wlan0: associate with AP 00:07:cb:58:be:fb
[ 6484.654112] wlan0: RX AssocResp from 00:07:cb:58:be:fb (capab=0x411 status=0
aid=1)
[ 6484.654115] wlan0: associated
[ 6484.666722] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 6495.400009] wlan0: no IPv6 routers present
[ 8138.905092] wlan0: deauthenticating by local choice (reason=3)
[ 8178.574364] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 8219.970231] wlan0: authenticate with AP 00:07:cb:58:be:fb
[ 8219.971978] wlan0: authenticated
[ 8219.971981] wlan0: associate with AP 00:07:cb:58:be:fb
[ 8219.974000] wlan0: RX AssocResp from 00:07:cb:58:be:fb (capab=0x411 status=0
aid=1)
[ 8219.974004] wlan0: associated
[ 8219.986599] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 8230.184012] wlan0: no IPv6 routers present
** Model information
sys_vendor: Packard Bell BV
product_name: IMEDIA 8040
product_version: PB80133702
chassis_vendor: Packard Bell BV
chassis_version: To Be Filled By O.E.M.
bios_vendor: American Megatrends Inc.
bios_version: PBANTON.P20
board_vendor: Packard Bell BV
board_name: To be filled by O.E.M.
board_version: To be filled by O.E.M.
** Loaded modules:
Module Size Used by
rt2500usb 22532 0
arc4 2256 2
ecb 3520 2
snd_hda_codec_realtek 271908 1
rt73usb 28020 0
crc_itu_t 2432 1 rt73usb
rt2x00usb 13424 2 rt2500usb,rt73usb
rt2x00lib 35024 3 rt2500usb,rt73usb,rt2x00usb
led_class 5528 1 rt2x00lib
snd_hda_intel 29128 1
snd_hda_codec 83920 2 snd_hda_codec_realtek,snd_hda_intel
input_polldev 4928 1 rt2x00lib
snd_hwdep 9288 1 snd_hda_codec
mac80211 157456 2 rt2x00usb,rt2x00lib
snd_pcm 89240 2 snd_hda_intel,snd_hda_codec
snd_seq 58528 0
snd_timer 23888 2 snd_pcm,snd_seq
snd_seq_device 8324 1 snd_seq
cfg80211 98600 2 rt2x00lib,mac80211
usb_storage 64624 0
i2c_nforce2 8168 0
snd 71608 10
snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_seq,snd_timer,snd_seq_device
amd64_edac_mod 23520 0
soundcore 8816 1 snd
i2c_core 26768 1 i2c_nforce2
rfkill 23544 1 cfg80211
k8temp 5424 0
edac_core 50444 1 amd64_edac_mod
snd_page_alloc 10768 2 snd_hda_intel,snd_pcm
serio_raw 6564 0
evdev 11504 11
pcspkr 3280 0
psmouse 46172 0
wmi 8144 0
button 7072 0
processor 43164 0
ext3 133616 2
jbd 53624 1 ext3
mbcache 9524 1 ext3
ide_cd_mod 30344 0
cdrom 36200 1 ide_cd_mod
ide_pci_generic 5156 0
ata_generic 6132 0
sd_mod 37608 4
crc_t10dif 2208 1 sd_mod
ohci_hcd 24700 0
forcedeth 57404 0
amd74xx 7208 0
ide_core 117744 3 ide_cd_mod,ide_pci_generic,amd74xx
ehci_hcd 37600 0
ahci 41552 3
libata 191148 2 ata_generic,ahci
scsi_mod 173200 3 usb_storage,sd_mod,libata
thermal 17376 0
fan 5768 0
thermal_sys 17936 3 processor,thermal,fan
** Network interface configuration:
# Used by ifup(8) and ifdown(8). See the interfaces(5) manpage or
# /usr/share/doc/ifupdown/examples for more information.
auto lo wlan0
iface lo inet loopback
iface wlan0 inet dhcp
wireless-mode managed
wireless-essid moine
wireless-enc restricted
wireless-key 00b4313234
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state
DOWN qlen 1000
link/ether 00:1e:90:b3:56:8e brd ff:ff:ff:ff:ff:ff
3: wmaster0: <UP,LOWER_UP> mtu 0 qdisc pfifo_fast state UNKNOWN qlen 1000
link/ieee802.11 00:1c:df:9f:57:fb brd 00:00:00:00:00:00
4: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP
qlen 1000
link/ether 00:1c:df:9f:57:fb brd ff:ff:ff:ff:ff:ff
inet 192.168.0.10/24 brd 192.168.0.255 scope global wlan0
inet6 fe80::21c:dfff:fe9f:57fb/64 scope link
valid_lft forever preferred_lft forever
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes
packets errs drop fifo colls carrier compressed
lo: 2860 40 0 0 0 0 0 0 2860
40 0 0 0 0 0 0
eth0: 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0
wmaster0: 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0
wlan0:21964500 18122 0 0 0 0 0 0 1281823
11735 0 0 0 0 0 0
*** Protocol statistics:
Ip:
17982 total packets received
10 with invalid addresses
0 forwarded
0 incoming packets discarded
15997 incoming packets delivered
11630 requests sent out
61 dropped because of missing route
Icmp:
6 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
destination unreachable: 2
echo replies: 4
8 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
destination unreachable: 2
echo request: 6
IcmpMsg:
InType0: 4
InType3: 2
OutType3: 2
OutType8: 6
Tcp:
201 active connections openings
3 passive connection openings
0 failed connection attempts
10 connection resets received
1 connections established
15700 segments received
11388 segments send out
42 segments retransmited
0 bad segments received.
66 resets sent
Udp:
206 packets received
0 packets to unknown port received.
2 packet receive errors
213 packets sent
RcvbufErrors: 2
UdpLite:
TcpExt:
7 packets pruned from receive queue because of socket buffer overrun
64 TCP sockets finished time wait in fast timer
176 delayed acks sent
Quick ack mode was activated 11 times
6 packets directly queued to recvmsg prequeue.
2 bytes directly received in process context from prequeue
11810 packet headers predicted
346 acknowledgments not containing data payload received
129 predicted acknowledgments
1 congestion windows recovered without slow start after partial ack
2 timeouts after SACK recovery
12 other TCP timeouts
234 packets collapsed in receive queue due to low socket buffer
12 DSACKs sent for old packets
1 DSACKs received
10 connections reset due to unexpected data
4 connections reset due to early user close
5 connections aborted due to timeout
TCPSackShiftFallback: 1
IpExt:
InBcastPkts: 83
InOctets: 21695208
OutOctets: 902183
InBcastOctets: 18832
*** Device features:
eth0: 0x20
lo: 0x13865
wlan0: 0x2000
wmaster0: 0x2000
** PCI devices:
00:00.0 RAM memory [0500]: nVidia Corporation MCP67 Memory Controller
[10de:0547] (rev a2)
Subsystem: Packard Bell B.V. Device [1631:e906]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:01.0 ISA bridge [0601]: nVidia Corporation MCP67 ISA Bridge [10de:0548] (rev
a2)
Subsystem: Packard Bell B.V. Device [1631:e906]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Region 0: I/O ports at 2f00 [size=256]
00:01.1 SMBus [0c05]: nVidia Corporation MCP67 SMBus [10de:0542] (rev a2)
Subsystem: Packard Bell B.V. Device [1631:e906]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at ec00 [size=64]
Region 4: I/O ports at 2d00 [size=64]
Region 5: I/O ports at 2e00 [size=64]
Capabilities: <access denied>
Kernel driver in use: nForce2_smbus
00:02.0 USB Controller [0c03]: nVidia Corporation MCP67 OHCI USB 1.1 Controller
[10de:055e] (rev a2) (prog-if 10 [OHCI])
Subsystem: Packard Bell B.V. Device [1631:e906]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 20
Region 0: Memory at febff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
00:02.1 USB Controller [0c03]: nVidia Corporation MCP67 EHCI USB 2.0 Controller
[10de:055f] (rev a2) (prog-if 20 [EHCI])
Subsystem: Packard Bell B.V. Device [1631:e906]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 22
Region 0: Memory at febfec00 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:04.0 USB Controller [0c03]: nVidia Corporation MCP67 OHCI USB 1.1 Controller
[10de:055e] (rev a2) (prog-if 10 [OHCI])
Subsystem: Packard Bell B.V. Device [1631:e906]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at febfd000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
00:04.1 USB Controller [0c03]: nVidia Corporation MCP67 EHCI USB 2.0 Controller
[10de:055f] (rev a2) (prog-if 20 [EHCI])
Subsystem: Packard Bell B.V. Device [1631:e906]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 23
Region 0: Memory at febfe800 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:06.0 IDE interface [0101]: nVidia Corporation MCP67 IDE Controller
[10de:0560] (rev a1) (prog-if 8a [Master SecP PriP])
Subsystem: Packard Bell B.V. Device [1631:e906]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[size=1]
Region 4: I/O ports at ffa0 [size=16]
Capabilities: <access denied>
Kernel driver in use: AMD_IDE
00:07.0 Audio device [0403]: nVidia Corporation MCP67 High Definition Audio
[10de:055c] (rev a1)
Subsystem: Packard Bell B.V. Device [1631:e906]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at febf8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
00:08.0 PCI bridge [0604]: nVidia Corporation MCP67 PCI Bridge [10de:0561] (rev
a2) (prog-if 01 [Subtractive decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:09.0 SATA controller [0106]: nVidia Corporation MCP67 AHCI Controller
[10de:0554] (rev a2) (prog-if 01 [AHCI 1.0])
Subsystem: Packard Bell B.V. Device [1631:e906]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 23
Region 0: I/O ports at e480 [size=8]
Region 1: I/O ports at e400 [size=4]
Region 2: I/O ports at e080 [size=8]
Region 3: I/O ports at e000 [size=4]
Region 4: I/O ports at dc00 [size=16]
Region 5: Memory at febf6000 (32-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:0a.0 Ethernet controller [0200]: nVidia Corporation MCP67 Ethernet
[10de:054c] (rev a2)
Subsystem: Packard Bell B.V. Device [1631:e906]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 31
Region 0: Memory at febfc000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at d880 [size=8]
Region 2: Memory at febfe400 (32-bit, non-prefetchable) [size=256]
Region 3: Memory at febfe000 (32-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
Kernel driver in use: forcedeth
00:0b.0 PCI bridge [0604]: nVidia Corporation MCP67 PCI Express Bridge
[10de:0562] (rev a2) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:0c.0 PCI bridge [0604]: nVidia Corporation MCP67 PCI Express Bridge
[10de:0563] (rev a2) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:0d.0 PCI bridge [0604]: nVidia Corporation MCP67 PCI Express Bridge
[10de:0563] (rev a2) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:0e.0 PCI bridge [0604]: nVidia Corporation MCP67 PCI Express Bridge
[10de:0563] (rev a2) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:0f.0 PCI bridge [0604]: nVidia Corporation MCP67 PCI Express Bridge
[10de:0563] (rev a2) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:10.0 PCI bridge [0604]: nVidia Corporation MCP67 PCI Express Bridge
[10de:0563] (rev a2) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:11.0 PCI bridge [0604]: nVidia Corporation MCP67 PCI Express Bridge
[10de:0563] (rev a2) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=08, subordinate=08, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:12.0 VGA compatible controller [0300]: nVidia Corporation C68 [GeForce 7025
/ nForce 630a] [10de:053e] (rev a2) (prog-if 00 [VGA controller])
Subsystem: Packard Bell B.V. Device [1631:e906]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at fc000000 (64-bit, non-prefetchable) [size=16M]
Expansion ROM at febc0000 [disabled] [size=128K]
Capabilities: <access denied>
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel driver in use: k8temp
** USB devices:
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 058f:9360 Alcor Micro Corp. 8-in-1 Media Card Reader
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 050d:705a Belkin Components F5D7050A Wireless Adapter
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: squeeze/sid
APT prefers unstable
APT policy: (500, 'unstable')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.31-1-amd64 (SMP w/2 CPU cores)
Locale: LANG=en_US, LC_CTYPE=en_US (charmap=ISO-8859-1)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.31-1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.28 Debian configuration management sy
ii initramfs-tools [linux-initra 0.93.4 tools for generating an initramfs
ii module-init-tools 3.11-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.31-1-amd64 recommends:
pn firmware-linux-free <none> (no description available)
Versions of packages linux-image-2.6.31-1-amd64 suggests:
ii grub 0.97-59 GRand Unified Bootloader (dummy pa
pn linux-doc-2.6.31 <none> (no description available)
Versions of packages linux-image-2.6.31-1-amd64 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
-- debconf information:
linux-image-2.6.31-1-amd64/prerm/removing-running-kernel-2.6.31-1-amd64: true
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.31-1-amd64/postinst/depmod-error-initrd-2.6.31-1-amd64: false
linux-image-2.6.31-1-amd64/postinst/missing-firmware-2.6.31-1-amd64:
linux-image-2.6.31-1-amd64/prerm/would-invalidate-boot-loader-2.6.31-1-amd64:
true
linux-image-2.6.31-1-amd64/postinst/bootloader-test-error-2.6.31-1-amd64:
linux-image-2.6.31-1-amd64/postinst/bootloader-error-2.6.31-1-amd64:
--
Ken ar c'hentan | ** Breizh ha Linux atav! **
Jef | http://moinejf.free.fr/
--- End Message ---
