Package: linux-2.6
Version: 2.6.31-1
Severity: serious
Hi kernel maintainer,
starting with kernel 2.6.30-2, my boot process lock up with the
message "cryptsetup: lvm is not available", just after having asked the
LUKS passphrase. Currently, I can reproduce it with 2.6.30-2 and
2.6.31-1. It still works fine with 2.6.30-1.
It seems that LVM is not initialized and/or initialized differently
starting with 2.6.30-2.
It might be a problem of some missing configuration on my side, but
given that it was working up to 2.6.30-1 I would have expected at least
a NEWS.Debian entry telling me what to do. This is the main reason for
me reporting this bug as RC: is it possible to provide some smooth
upgrade experience?
My current lvm/crypt setup is as deployed by an out of the box d-i
installation a while ago, in the Lenny release timeframe.
I'm attaching: /etc/crypttab, /etc/fstab, /etc/lvm/lvm.conf,
/boot/grub/grub.cfg . Let me know if I can provide anything else useful.
Many thanks in advance and for your kernel maintenance work!
Cheers.
-- Package-specific info:
** Kernel log: boot messages should be attached
** Model information
sys_vendor: LENOVO
product_name: 647814G
product_version: ThinkPad X300
chassis_vendor: LENOVO
chassis_version: Not Available
bios_vendor: LENOVO
bios_version: 7TET26WW (1.02a)
board_vendor: LENOVO
board_name: 647814G
board_version: Not Available
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile PM965/GM965/GL960 Memory
Controller Hub [8086:2a00] (rev 0c)
Subsystem: Lenovo T61 [17aa:20b3]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile GM965/GL960
Integrated Graphics Controller [8086:2a02] (rev 0c) (prog-if 00 [VGA
controller])
Subsystem: Lenovo T61 [17aa:20b5]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 30
Region 0: Memory at fa000000 (64-bit, non-prefetchable) [size=1M]
Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 1800 [size=8]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
00:02.1 Display controller [0380]: Intel Corporation Mobile GM965/GL960
Integrated Graphics Controller [8086:2a03] (rev 0c)
Subsystem: Lenovo T61 [17aa:20b5]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at fa100000 (64-bit, non-prefetchable) [size=1M]
Capabilities: <access denied>
00:19.0 Ethernet controller [0200]: Intel Corporation 82566MM Gigabit Network
Connection [8086:1049] (rev 03)
Subsystem: Lenovo ThinkPad T61 [17aa:20b9]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 27
Region 0: Memory at fa200000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at fa225000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at 1840 [size=32]
Capabilities: <access denied>
Kernel driver in use: e1000e
00:1a.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI
Controller #4 [8086:2834] (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo ThinkPad T61 [17aa:20aa]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 1860 [size=32]
Kernel driver in use: uhci_hcd
00:1a.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI
Controller #5 [8086:2835] (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo ThinkPad T60 [17aa:20aa]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 1880 [size=32]
Kernel driver in use: uhci_hcd
00:1a.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI
Controller #2 [8086:283a] (rev 03) (prog-if 20 [EHCI])
Subsystem: Lenovo ThinkPad T61 [17aa:20ab]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 0: Memory at fa426c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1b.0 Audio device [0403]: Intel Corporation 82801H (ICH8 Family) HD Audio
Controller [8086:284b] (rev 03)
Subsystem: Lenovo ThinkPad T61 [17aa:20ac]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fa220000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express
Port 1 [8086:283f] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f4000000-f5ffffff
Prefetchable memory behind bridge: 00000000fa500000-00000000fa5fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1c.1 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express
Port 2 [8086:2841] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: f8000000-f9ffffff
Prefetchable memory behind bridge: 00000000fa600000-00000000fa6fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1c.2 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express
Port 3 [8086:2843] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: f6000000-f7ffffff
Prefetchable memory behind bridge: 00000000fa700000-00000000fa7fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1d.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI
Controller #1 [8086:2830] (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo ThinkPad T61 [17aa:20aa]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at 18a0 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI
Controller #2 [8086:2831] (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo ThinkPad T61 [17aa:20aa]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 18c0 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI
Controller #3 [8086:2832] (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo ThinkPad T61 [17aa:20aa]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 18e0 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI
Controller #1 [8086:2836] (rev 03) (prog-if 20 [EHCI])
Subsystem: Lenovo ThinkPad T61 [17aa:20ab]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 0: Memory at fa427000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge
[8086:2448] (rev f3) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=0d, subordinate=0d, sec-latency=32
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801HBM (ICH8M-E) LPC Interface
Controller [8086:2811] (rev 03)
Subsystem: Lenovo T61 [17aa:20b6]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.1 IDE interface [0101]: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E)
IDE Controller [8086:2850] (rev 03) (prog-if 8a [Master SecP PriP])
Subsystem: Lenovo ThinkPad T61 [17aa:20a6]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 1c00 [size=16]
Kernel driver in use: PIIX_IDE
00:1f.2 SATA controller [0106]: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E)
SATA AHCI Controller [8086:2829] (rev 03) (prog-if 01 [AHCI 1.0])
Subsystem: Lenovo ThinkPad T61 [17aa:20a7]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 28
Region 0: I/O ports at 1c50 [size=8]
Region 1: I/O ports at 1c44 [size=4]
Region 2: I/O ports at 1c48 [size=8]
Region 3: I/O ports at 1c40 [size=4]
Region 4: I/O ports at 1c20 [size=32]
Region 5: Memory at fa426000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 82801H (ICH8 Family) SMBus Controller
[8086:283e] (rev 03)
Subsystem: Lenovo ThinkPad T61 [17aa:20a9]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fa427400 (32-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 1c60 [size=32]
Kernel driver in use: i801_smbus
03:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 4965 AG or
AGN [Kedron] Network Connection [8086:4230] (rev 61)
Subsystem: Intel Corporation Lenovo ThinkPad T61 [8086:1111]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR+ <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 29
Region 0: Memory at f9f00000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: iwlagn
** USB devices:
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 003: ID 0483:2016 SGS Thomson Microelectronics Fingerprint Reader
Bus 003 Device 002: ID 0a5c:2110 Broadcom Corp. Bluetooth Controller
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 002: ID 17ef:4807 Lenovo
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: squeeze/sid
APT prefers unstable
APT policy: (500, 'unstable'), (500, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.30-1-amd64 (SMP w/2 CPU cores)
Locale: LANG=it_IT.UTF-8, LC_CTYPE=it_IT.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.31-1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.28 Debian configuration management sy
ii initramfs-tools [linux-initra 0.93.4 tools for generating an initramfs
ii module-init-tools 3.11-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.31-1-amd64 recommends:
ii firmware-linux-free 2.6.31-1 Binary firmware for various driver
Versions of packages linux-image-2.6.31-1-amd64 suggests:
ii grub 0.97-59 GRand Unified Bootloader (dummy pa
pn linux-doc-2.6.31 <none> (no description available)
Versions of packages linux-image-2.6.31-1-amd64 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
ii firmware-iwlwifi 0.21 Binary firmware for Intel Wireless
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
-- debconf information:
* linux-image-2.6.31-1-amd64/postinst/missing-firmware-2.6.31-1-amd64:
linux-image-2.6.31-1-amd64/postinst/bootloader-error-2.6.31-1-amd64:
linux-image-2.6.31-1-amd64/prerm/removing-running-kernel-2.6.31-1-amd64: true
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.31-1-amd64/prerm/would-invalidate-boot-loader-2.6.31-1-amd64:
true
linux-image-2.6.31-1-amd64/postinst/depmod-error-initrd-2.6.31-1-amd64: false
linux-image-2.6.31-1-amd64/postinst/bootloader-test-error-2.6.31-1-amd64:
sda2_crypt /dev/sda2 none luks
# /etc/fstab: static file system information.
#
# <file system> <mount point> <type> <options> <dump> <pass>
proc /proc proc defaults 0 0
/dev/mapper/usha-root / ext3 errors=remount-ro 0 1
/dev/sda1 /boot ext3 defaults,relatime 0 2
/dev/mapper/usha-home /home ext3 defaults,relatime 0 2
/dev/mapper/usha-swap none swap sw 0 0
/dev/hda /media/cdrom0 udf,iso9660 user,noauto 0 0
tmpfs /tmp tmpfs defaults 0 0
tmpfs /var/tmp tmpfs defaults 0 0
tmpfs /var/lock tmpfs defaults 0 0
# This is an example configuration file for the LVM2 system.
# It contains the default settings that would be used if there was no
# /etc/lvm/lvm.conf file.
#
# Refer to 'man lvm.conf' for further information including the file layout.
#
# To put this file in a different directory and override /etc/lvm set
# the environment variable LVM_SYSTEM_DIR before running the tools.
# This section allows you to configure which block devices should
# be used by the LVM system.
devices {
# Where do you want your volume groups to appear ?
dir = "/dev"
# An array of directories that contain the device nodes you wish
# to use with LVM2.
scan = [ "/dev" ]
# If several entries in the scanned directories correspond to the
# same block device and the tools need to display a name for device,
# all the pathnames are matched against each item in the following
# list of regular expressions in turn and the first match is used.
preferred_names = [ ]
# Try to avoid using undescriptive /dev/dm-N names, if present.
# preferred_names = [ "^/dev/mpath/", "^/dev/mapper/mpath", "^/dev/[hs]d" ]
# A filter that tells LVM2 to only use a restricted set of devices.
# The filter consists of an array of regular expressions. These
# expressions can be delimited by a character of your choice, and
# prefixed with either an 'a' (for accept) or 'r' (for reject).
# The first expression found to match a device name determines if
# the device will be accepted or rejected (ignored). Devices that
# don't match any patterns are accepted.
# Be careful if there there are symbolic links or multiple filesystem
# entries for the same device as each name is checked separately against
# the list of patterns. The effect is that if any name matches any 'a'
# pattern, the device is accepted; otherwise if any name matches any 'r'
# pattern it is rejected; otherwise it is accepted.
# Don't have more than one filter line active at once: only one gets used.
# Run vgscan after you change this parameter to ensure that
# the cache file gets regenerated (see below).
# If it doesn't do what you expect, check the output of 'vgscan -vvvv'.
# By default we accept every block device:
filter = [ "a/.*/" ]
# Exclude the cdrom drive
# filter = [ "r|/dev/cdrom|" ]
# When testing I like to work with just loopback devices:
# filter = [ "a/loop/", "r/.*/" ]
# Or maybe all loops and ide drives except hdc:
# filter =[ "a|loop|", "r|/dev/hdc|", "a|/dev/ide|", "r|.*|" ]
# Use anchors if you want to be really specific
# filter = [ "a|^/dev/hda8$|", "r/.*/" ]
# The results of the filtering are cached on disk to avoid
# rescanning dud devices (which can take a very long time).
# By default this cache is stored in the /etc/lvm/cache directory
# in a file called '.cache'.
# It is safe to delete the contents: the tools regenerate it.
# (The old setting 'cache' is still respected if neither of
# these new ones is present.)
cache_dir = "/etc/lvm/cache"
cache_file_prefix = ""
# You can turn off writing this cache file by setting this to 0.
write_cache_state = 1
# Advanced settings.
# List of pairs of additional acceptable block device types found
# in /proc/devices with maximum (non-zero) number of partitions.
# types = [ "fd", 16 ]
# If sysfs is mounted (2.6 kernels) restrict device scanning to
# the block devices it believes are valid.
# 1 enables; 0 disables.
sysfs_scan = 1
# By default, LVM2 will ignore devices used as components of
# software RAID (md) devices by looking for md superblocks.
# 1 enables; 0 disables.
md_component_detection = 1
# By default, if a PV is placed directly upon an md device, LVM2
# will align its data blocks with the md device's stripe-width.
# 1 enables; 0 disables.
md_chunk_alignment = 1
# By default, the start of a PV's data area will be a multiple of
# the 'minimum_io_size' or 'optimal_io_size' exposed in sysfs.
# - minimum_io_size - the smallest request the device can perform
# w/o incurring a read-modify-write penalty (e.g. MD's chunk size)
# - optimal_io_size - the device's preferred unit of receiving I/O
# (e.g. MD's stripe width)
# minimum_io_size is used if optimal_io_size is undefined (0).
# If md_chunk_alignment is enabled, that detects the optimal_io_size.
# This setting takes precedence over md_chunk_alignment.
# 1 enables; 0 disables.
data_alignment_detection = 1
# Alignment (in KB) of start of data area when creating a new PV.
# If a PV is placed directly upon an md device and md_chunk_alignment or
# data_alignment_detection is enabled this parameter is ignored.
# Set to 0 for the default alignment of 64KB or page size, if larger.
data_alignment = 0
# By default, the start of the PV's aligned data area will be shifted by
# the 'alignment_offset' exposed in sysfs. This offset is often 0 but
# may be non-zero; e.g.: certain 4KB sector drives that compensate for
# windows partitioning will have an alignment_offset of 3584 bytes
# (sector 7 is the lowest aligned logical block, the 4KB sectors start
# at LBA -1, and consequently sector 63 is aligned on a 4KB boundary).
# 1 enables; 0 disables.
data_alignment_offset_detection = 1
# If, while scanning the system for PVs, LVM2 encounters a device-mapper
# device that has its I/O suspended, it waits for it to become accessible.
# Set this to 1 to skip such devices. This should only be needed
# in recovery situations.
ignore_suspended_devices = 0
}
# This section that allows you to configure the nature of the
# information that LVM2 reports.
log {
# Controls the messages sent to stdout or stderr.
# There are three levels of verbosity, 3 being the most verbose.
verbose = 0
# Should we send log messages through syslog?
# 1 is yes; 0 is no.
syslog = 1
# Should we log error and debug messages to a file?
# By default there is no log file.
#file = "/var/log/lvm2.log"
# Should we overwrite the log file each time the program is run?
# By default we append.
overwrite = 0
# What level of log messages should we send to the log file and/or syslog?
# There are 6 syslog-like log levels currently in use - 2 to 7 inclusive.
# 7 is the most verbose (LOG_DEBUG).
level = 0
# Format of output messages
# Whether or not (1 or 0) to indent messages according to their severity
indent = 1
# Whether or not (1 or 0) to display the command name on each line output
command_names = 0
# A prefix to use before the message text (but after the command name,
# if selected). Default is two spaces, so you can see/grep the severity
# of each message.
prefix = " "
# To make the messages look similar to the original LVM tools use:
# indent = 0
# command_names = 1
# prefix = " -- "
# Set this if you want log messages during activation.
# Don't use this in low memory situations (can deadlock).
# activation = 0
}
# Configuration of metadata backups and archiving. In LVM2 when we
# talk about a 'backup' we mean making a copy of the metadata for the
# *current* system. The 'archive' contains old metadata configurations.
# Backups are stored in a human readeable text format.
backup {
# Should we maintain a backup of the current metadata configuration ?
# Use 1 for Yes; 0 for No.
# Think very hard before turning this off!
backup = 1
# Where shall we keep it ?
# Remember to back up this directory regularly!
backup_dir = "/etc/lvm/backup"
# Should we maintain an archive of old metadata configurations.
# Use 1 for Yes; 0 for No.
# On by default. Think very hard before turning this off.
archive = 1
# Where should archived files go ?
# Remember to back up this directory regularly!
archive_dir = "/etc/lvm/archive"
# What is the minimum number of archive files you wish to keep ?
retain_min = 10
# What is the minimum time you wish to keep an archive file for ?
retain_days = 30
}
# Settings for the running LVM2 in shell (readline) mode.
shell {
# Number of lines of history to store in ~/.lvm_history
history_size = 100
}
# Miscellaneous global LVM2 settings
global {
# The file creation mask for any files and directories created.
# Interpreted as octal if the first digit is zero.
umask = 077
# Allow other users to read the files
#umask = 022
# Enabling test mode means that no changes to the on disk metadata
# will be made. Equivalent to having the -t option on every
# command. Defaults to off.
test = 0
# Default value for --units argument
units = "h"
# Whether or not to communicate with the kernel device-mapper.
# Set to 0 if you want to use the tools to manipulate LVM metadata
# without activating any logical volumes.
# If the device-mapper kernel driver is not present in your kernel
# setting this to 0 should suppress the error messages.
activation = 1
# If we can't communicate with device-mapper, should we try running
# the LVM1 tools?
# This option only applies to 2.4 kernels and is provided to help you
# switch between device-mapper kernels and LVM1 kernels.
# The LVM1 tools need to be installed with .lvm1 suffices
# e.g. vgscan.lvm1 and they will stop working after you start using
# the new lvm2 on-disk metadata format.
# The default value is set when the tools are built.
# fallback_to_lvm1 = 0
# The default metadata format that commands should use - "lvm1" or "lvm2".
# The command line override is -M1 or -M2.
# Defaults to "lvm1" if compiled in, else "lvm2".
# format = "lvm1"
# Location of proc filesystem
proc = "/proc"
# Type of locking to use. Defaults to local file-based locking (1).
# Turn locking off by setting to 0 (dangerous: risks metadata corruption
# if LVM2 commands get run concurrently).
# Type 2 uses the external shared library locking_library.
# Type 3 uses built-in clustered locking.
# Type 4 uses read-only locking which forbids any operations that might
# change metadata.
locking_type = 1
# Set to 0 to fail when a lock request cannot be satisfied immediately.
wait_for_locks = 1
# If using external locking (type 2) and initialisation fails,
# with this set to 1 an attempt will be made to use the built-in
# clustered locking.
# If you are using a customised locking_library you should set this to 0.
fallback_to_clustered_locking = 1
# If an attempt to initialise type 2 or type 3 locking failed, perhaps
# because cluster components such as clvmd are not running, with this set
# to 1 an attempt will be made to use local file-based locking (type 1).
# If this succeeds, only commands against local volume groups will proceed.
# Volume Groups marked as clustered will be ignored.
fallback_to_local_locking = 1
# Local non-LV directory that holds file-based locks while commands are
# in progress. A directory like /tmp that may get wiped on reboot is OK.
locking_dir = "/var/lock/lvm"
# Whenever there are competing read-only and read-write access requests for
# a volume group's metadata, instead of always granting the read-only
# requests immediately, delay them to allow the read-write requests to be
# serviced. Without this setting, write access may be stalled by a high
# volume of read-only requests.
# NB. This option only affects locking_type = 1 viz. local file-based
# locking.
prioritise_write_locks = 1
# Other entries can go here to allow you to load shared libraries
# e.g. if support for LVM1 metadata was compiled as a shared library use
# format_libraries = "liblvm2format1.so"
# Full pathnames can be given.
# Search this directory first for shared libraries.
# library_dir = "/lib/lvm2"
# The external locking library to load if locking_type is set to 2.
# locking_library = "liblvm2clusterlock.so"
}
activation {
# Set to 0 to disable udev syncronisation (if compiled into the binaries).
# Processes will not wait for notification from udev.
# They will continue irrespective of any possible udev processing
# in the background. You should only use this if udev is not running
# or has rules that ignore the devices LVM2 creates.
# The command line argument --nodevsync takes precedence over this setting.
# If set to 1 when udev is not running, and there are LVM2 processes
# waiting for udev, run 'dmsetup udevcomplete_all' manually to wake them up.
udev_sync = 1
# How to fill in missing stripes if activating an incomplete volume.
# Using "error" will make inaccessible parts of the device return
# I/O errors on access. You can instead use a device path, in which
# case, that device will be used to in place of missing stripes.
# But note that using anything other than "error" with mirrored
# or snapshotted volumes is likely to result in data corruption.
missing_stripe_filler = "error"
# How much stack (in KB) to reserve for use while devices suspended
reserved_stack = 256
# How much memory (in KB) to reserve for use while devices suspended
reserved_memory = 8192
# Nice value used while devices suspended
process_priority = -18
# If volume_list is defined, each LV is only activated if there is a
# match against the list.
# "vgname" and "vgname/lvname" are matched exactly.
# "@tag" matches any tag set in the LV or VG.
# "@*" matches if any tag defined on the host is also set in the LV or VG
#
# volume_list = [ "vg1", "vg2/lvol1", "@tag1", "@*" ]
# Size (in KB) of each copy operation when mirroring
mirror_region_size = 512
# Setting to use when there is no readahead value stored in the metadata.
#
# "none" - Disable readahead.
# "auto" - Use default value chosen by kernel.
readahead = "auto"
# 'mirror_image_fault_policy' and 'mirror_log_fault_policy' define
# how a device failure affecting a mirror is handled.
# A mirror is composed of mirror images (copies) and a log.
# A disk log ensures that a mirror does not need to be re-synced
# (all copies made the same) every time a machine reboots or crashes.
#
# In the event of a failure, the specified policy will be used to determine
# what happens. This applies to automatic repairs (when the mirror is being
# monitored by dmeventd) and to manual lvconvert --repair when
# --use-policies is given.
#
# "remove" - Simply remove the faulty device and run without it. If
# the log device fails, the mirror would convert to using
# an in-memory log. This means the mirror will not
# remember its sync status across crashes/reboots and
# the entire mirror will be re-synced. If a
# mirror image fails, the mirror will convert to a
# non-mirrored device if there is only one remaining good
# copy.
#
# "allocate" - Remove the faulty device and try to allocate space on
# a new device to be a replacement for the failed device.
# Using this policy for the log is fast and maintains the
# ability to remember sync state through crashes/reboots.
# Using this policy for a mirror device is slow, as it
# requires the mirror to resynchronize the devices, but it
# will preserve the mirror characteristic of the device.
# This policy acts like "remove" if no suitable device and
# space can be allocated for the replacement.
#
# "allocate_anywhere" - Not yet implemented. Useful to place the log device
# temporarily on same physical volume as one of the mirror
# images. This policy is not recommended for mirror devices
# since it would break the redundant nature of the mirror. This
# policy acts like "remove" if no suitable device and space can
# be allocated for the replacement.
mirror_log_fault_policy = "allocate"
mirror_device_fault_policy = "remove"
}
####################
# Advanced section #
####################
# Metadata settings
#
# metadata {
# Default number of copies of metadata to hold on each PV. 0, 1 or 2.
# You might want to override it from the command line with 0
# when running pvcreate on new PVs which are to be added to large VGs.
# pvmetadatacopies = 1
# Approximate default size of on-disk metadata areas in sectors.
# You should increase this if you have large volume groups or
# you want to retain a large on-disk history of your metadata changes.
# pvmetadatasize = 255
# List of directories holding live copies of text format metadata.
# These directories must not be on logical volumes!
# It's possible to use LVM2 with a couple of directories here,
# preferably on different (non-LV) filesystems, and with no other
# on-disk metadata (pvmetadatacopies = 0). Or this can be in
# addition to on-disk metadata areas.
# The feature was originally added to simplify testing and is not
# supported under low memory situations - the machine could lock up.
#
# Never edit any files in these directories by hand unless you
# you are absolutely sure you know what you are doing! Use
# the supplied toolset to make changes (e.g. vgcfgrestore).
# dirs = [ "/etc/lvm/metadata", "/mnt/disk2/lvm/metadata2" ]
#}
# Event daemon
#
dmeventd {
# mirror_library is the library used when monitoring a mirror device.
#
# "libdevmapper-event-lvm2mirror.so" attempts to recover from
# failures. It removes failed devices from a volume group and
# reconfigures a mirror as necessary. If no mirror library is
# provided, mirrors are not monitored through dmeventd.
mirror_library = "libdevmapper-event-lvm2mirror.so"
# snapshot_library is the library used when monitoring a snapshot device.
#
# "libdevmapper-event-lvm2snapshot.so" monitors the filling of
# snapshots and emits a warning through syslog, when the use of
# snapshot exceedes 80%. The warning is repeated when 85%, 90% and
# 95% of the snapshot are filled.
snapshot_library = "libdevmapper-event-lvm2snapshot.so"
}
#
# DO NOT EDIT THIS FILE
#
# It is automatically generated by /usr/sbin/grub-mkconfig using templates
# from /etc/grub.d and settings from /etc/default/grub
#
### BEGIN /etc/grub.d/00_header ###
set default=0
insmod ext2
set root=(hd0,1)
search --no-floppy --fs-uuid --set 91017fd4-d9dc-46f0-85ce-dd2876838c09
if loadfont /grub/unicode.pf2 ; then
set gfxmode=640x480
insmod gfxterm
insmod vbe
if terminal_output gfxterm ; then true ; else
# For backward compatibility with versions of terminal.mod that don't
# understand terminal_output
terminal gfxterm
fi
fi
set timeout=5
### END /etc/grub.d/00_header ###
### BEGIN /etc/grub.d/05_debian_theme ###
insmod ext2
set root=(hd0,1)
search --no-floppy --fs-uuid --set 91017fd4-d9dc-46f0-85ce-dd2876838c09
insmod png
if background_image /grub/moreblue-orbit-grub.png ; then
set color_normal=black/black
set color_highlight=magenta/black
else
set menu_color_normal=cyan/blue
set menu_color_highlight=white/blue
fi
### END /etc/grub.d/05_debian_theme ###
### BEGIN /etc/grub.d/10_linux ###
menuentry "Debian GNU/Linux, with Linux 2.6.31-1-amd64" {
insmod ext2
set root=(hd0,1)
search --no-floppy --fs-uuid --set 91017fd4-d9dc-46f0-85ce-dd2876838c09
linux /vmlinuz-2.6.31-1-amd64 root=/dev/mapper/usha-root ro
usbcore.autosuspend=1 quiet
initrd /initrd.img-2.6.31-1-amd64
}
menuentry "Debian GNU/Linux, with Linux 2.6.31-1-amd64 (recovery mode)" {
insmod ext2
set root=(hd0,1)
search --no-floppy --fs-uuid --set 91017fd4-d9dc-46f0-85ce-dd2876838c09
linux /vmlinuz-2.6.31-1-amd64 root=/dev/mapper/usha-root ro single
usbcore.autosuspend=1
initrd /initrd.img-2.6.31-1-amd64
}
menuentry "Debian GNU/Linux, with Linux 2.6.30-2-amd64" {
insmod ext2
set root=(hd0,1)
search --no-floppy --fs-uuid --set 91017fd4-d9dc-46f0-85ce-dd2876838c09
linux /vmlinuz-2.6.30-2-amd64 root=/dev/mapper/usha-root ro
usbcore.autosuspend=1 quiet
initrd /initrd.img-2.6.30-2-amd64
}
menuentry "Debian GNU/Linux, with Linux 2.6.30-2-amd64 (recovery mode)" {
insmod ext2
set root=(hd0,1)
search --no-floppy --fs-uuid --set 91017fd4-d9dc-46f0-85ce-dd2876838c09
linux /vmlinuz-2.6.30-2-amd64 root=/dev/mapper/usha-root ro single
usbcore.autosuspend=1
initrd /initrd.img-2.6.30-2-amd64
}
menuentry "Debian GNU/Linux, with Linux 2.6.30-1-amd64" {
insmod ext2
set root=(hd0,1)
search --no-floppy --fs-uuid --set 91017fd4-d9dc-46f0-85ce-dd2876838c09
linux /vmlinuz-2.6.30-1-amd64 root=/dev/mapper/usha-root ro
usbcore.autosuspend=1 quiet
initrd /initrd.img-2.6.30-1-amd64
}
menuentry "Debian GNU/Linux, with Linux 2.6.30-1-amd64 (recovery mode)" {
insmod ext2
set root=(hd0,1)
search --no-floppy --fs-uuid --set 91017fd4-d9dc-46f0-85ce-dd2876838c09
linux /vmlinuz-2.6.30-1-amd64 root=/dev/mapper/usha-root ro single
usbcore.autosuspend=1
initrd /initrd.img-2.6.30-1-amd64
}
### END /etc/grub.d/10_linux ###
### BEGIN /etc/grub.d/30_os-prober ###
### END /etc/grub.d/30_os-prober ###
### BEGIN /etc/grub.d/40_custom ###
# This file provides an easy way to add custom menu entries. Simply type the
# menu entries you want to add after this comment. Be careful not to change
# the 'exec tail' line above.
### END /etc/grub.d/40_custom ###
