Bug#498021: marked as done (linux-image-2.6.26-1-686: task blocked after connecting the SDHC memory card)

[Debian Bug Tracking System]

Your message dated Wed, 7 Oct 2009 22:18:16 +0200
with message-id <20091007201816.ga30...@galadriel.inutil.org>
and subject line Re: This problem is common on Eeepc
has caused the Debian Bug report #498021,
regarding linux-image-2.6.26-1-686: task blocked after connecting the SDHC 
memory card
to be marked as done.

This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.

(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact ow...@bugs.debian.org
immediately.)


-- 
498021: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=498021
Debian Bug Tracking System
Contact ow...@bugs.debian.org with problems

--- Begin Message ---

Package: linux-image-2.6.26-1-686
Version: 2.6.26-3
Severity: important

After inserting of SDHC memory card with capacity of 4GB, a get the following

messages (output of dmesg command quoted below):

  56.738417] usb-storage: device scan complete

[ 56.758415] scsi 2:0:0:0: Direct-Access Generic USB Storage-SMC I03A PQ: 0 ANSI: 0 CCS [ 56.771004] scsi 2:0:0:1: Direct-Access Generic USB Storage-CFC I03A PQ: 0 ANSI: 0 CCS [ 56.787004] scsi 2:0:0:2: Direct-Access Generic USB Storage-MMC I03A PQ: 0 ANSI: 0 CCS [ 56.810070] scsi 2:0:0:3: Direct-Access Generic USB Storage-MSC I03A PQ: 0 ANSI: 0 CCS

[   57.027302] Driver 'sd' needs updating - please use bus_type methods
[   57.027666] sd 2:0:0:0: [sda] Attached SCSI removable disk
[   57.031306] sd 2:0:0:1: [sdb] Attached SCSI removable disk
[   57.054077] sd 2:0:0:2: [sdc] Spinning up disk...

[ 73.076299] .....................................................................................not responding... [ 195.511753] usb 5-5: reset high speed USB device using ehci_hcd and address 3 [ 227.894857] usb 5-5: reset high speed USB device using ehci_hcd and address 3 [ 259.751599] usb 5-5: reset high speed USB device using ehci_hcd and address 3 [ 290.784237] usb 5-5: reset high speed USB device using ehci_hcd and address 3 [ 321.104274] usb 5-5: reset high speed USB device using ehci_hcd and address 3 [ 351.402376] usb 5-5: reset high speed USB device using ehci_hcd and address 3

[  377.958990] INFO: task vol_id:4508 blocked for more than 120 seconds.

[ 377.958999] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.

[  377.959005] vol_id        D 50f586c1     0  4508   4489

[ 377.959015] f77b20c0 00000086 f889c9e7 50f586c1 00000036 f77b224c c1ffbfa0 00000001 [ 377.959034] ffffffff ffffffff 00492425 00000000 f771368c f6f94038 00001d4c 00000000 [ 377.959052] 7fffffff 7fffffff f53f9d2c 00000002 c02b7e69 00000086 c0129a63 00000000

[  377.959071] Call Trace:
[  377.959123]  [<f889c9e7>] scsi_get_cmd_from_req+0x1b/0x41 [scsi_mod]
[  377.959242]  [<c02b7e69>] schedule_timeout+0x13/0x86
[  377.959258]  [<c0129a63>] __mod_timer+0x99/0xa3
[  377.959310]  [<f889dbb0>] scsi_request_fn+0x2e6/0x32a [scsi_mod]
[  377.959366]  [<c02b758d>] wait_for_common+0xaf/0x10f
[  377.959388]  [<c011b61d>] default_wake_function+0x0/0x8
[  377.959426]  [<c01d49d0>] blk_execute_rq+0x83/0x96
[  377.959440]  [<c01d49e3>] blk_end_sync_rq+0x0/0x25
[  377.959478]  [<c01dba6f>] cfq_set_request+0x0/0x269
[  377.959501]  [<c01cfe40>] elv_set_request+0x14/0x22
[  377.959520]  [<c01d22e6>] get_request+0x1e5/0x2c7
[  377.959570]  [<c01d2874>] get_request_wait+0x106/0x117
[  377.959640]  [<f889cfc4>] scsi_execute+0xc5/0x103 [scsi_mod]
[  377.959699]  [<f889d086>] scsi_execute_req+0x84/0xa1 [scsi_mod]
[  377.959791]  [<f889d0ee>] scsi_test_unit_ready+0x4b/0xaa [scsi_mod]
[  377.959876]  [<f8f02004>] sd_media_changed+0xd0/0x170 [sd_mod]
[  377.959913]  [<c0193d48>] check_disk_change+0x13/0x57
[  377.959934]  [<f8f01838>] sd_open+0xce/0x152 [sd_mod]
[  377.959968]  [<c019435c>] do_open+0xb6/0x28f
[  377.960963]  [<c01946b0>] blkdev_open+0x0/0x4d
[  377.960972]  [<c01946d5>] blkdev_open+0x25/0x4d
[  377.960994]  [<c0172b77>] __dentry_open+0x10d/0x1fc
[  377.961032]  [<c0172c82>] nameidata_to_filp+0x1c/0x2c
[  377.961060]  [<c017d382>] do_filp_open+0x34f/0x684
[  377.961167]  [<c01dc96a>] _atomic_dec_and_lock+0x2a/0x44
[  377.961185]  [<c0182376>] dput+0x25/0xbb
[  377.961251]  [<c0172994>] do_sys_open+0x40/0xb0
[  377.961289]  [<c0172a48>] sys_open+0x1e/0x23
[  377.961316]  [<c0103853>] sysenter_past_esp+0x78/0xb1
[  377.961369]  [<c02b0000>] serial_pnp_probe+0xde/0x16b
[  377.961416]  =======================
[  377.961423] INFO: task vol_id:4518 blocked for more than 120 seconds.

[ 377.961427] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.

[  377.961432] vol_id        D f7713cac     0  4518   4509

[ 377.961440] f5648ea0 00000082 f889c9e7 f7713cac f6da0c00 f564902c c1ffbfa0 00000001 [ 377.961454] ffffffff ffffbecf f8f0103c f713bd68 00000000 00000000 00000000 000000ff [ 377.961469] 7fffffff 7fffffff f569bd2c 00000002 c02b7e69 00000086 c0129a63 00000000

[  377.961484] Call Trace:
[  377.961510]  [<f889c9e7>] scsi_get_cmd_from_req+0x1b/0x41 [scsi_mod]
[  377.961572]  [<f8f0103c>] sd_prep_fn+0x52/0x780 [sd_mod]
[  377.961630]  [<c02b7e69>] schedule_timeout+0x13/0x86
[  377.961648]  [<c0129a63>] __mod_timer+0x99/0xa3
[  377.961729]  [<f889dbb0>] scsi_request_fn+0x2e6/0x32a [scsi_mod]
[  377.961783]  [<c02b758d>] wait_for_common+0xaf/0x10f
[  377.961816]  [<c011b61d>] default_wake_function+0x0/0x8
[  377.961876]  [<c01d49d0>] blk_execute_rq+0x83/0x96
[  377.961893]  [<c01d49e3>] blk_end_sync_rq+0x0/0x25
[  377.961934]  [<c01dba6f>] cfq_set_request+0x0/0x269
[  377.961963]  [<c01cfe40>] elv_set_request+0x14/0x22
[  377.961981]  [<c01d22e6>] get_request+0x1e5/0x2c7
[  377.962032]  [<c01d2874>] get_request_wait+0x106/0x117
[  377.962096]  [<f889cfc4>] scsi_execute+0xc5/0x103 [scsi_mod]
[  377.962151]  [<f889d086>] scsi_execute_req+0x84/0xa1 [scsi_mod]
[  377.962242]  [<f889d0ee>] scsi_test_unit_ready+0x4b/0xaa [scsi_mod]
[  377.962327]  [<f8f02004>] sd_media_changed+0xd0/0x170 [sd_mod]
[  377.962363]  [<c0193d48>] check_disk_change+0x13/0x57
[  377.962383]  [<f8f01838>] sd_open+0xce/0x152 [sd_mod]
[  377.962417]  [<c019435c>] do_open+0xb6/0x28f
[  377.962465]  [<c01946b0>] blkdev_open+0x0/0x4d
[  377.962473]  [<c01946d5>] blkdev_open+0x25/0x4d
[  377.962495]  [<c0172b77>] __dentry_open+0x10d/0x1fc
[  377.962532]  [<c0172c82>] nameidata_to_filp+0x1c/0x2c
[  377.962560]  [<c017d382>] do_filp_open+0x34f/0x684
[  377.962666]  [<c01dc96a>] _atomic_dec_and_lock+0x2a/0x44
[  377.962685]  [<c0182376>] dput+0x25/0xbb
[  377.962753]  [<c0172994>] do_sys_open+0x40/0xb0
[  377.962792]  [<c0172a48>] sys_open+0x1e/0x23
[  377.962819]  [<c0103853>] sysenter_past_esp+0x78/0xb1
[  377.962871]  [<c02b0000>] serial_pnp_probe+0xde/0x16b
[  377.962919]  =======================

[ 381.708008] usb 5-5: reset high speed USB device using ehci_hcd and address 3 [ 412.009302] usb 5-5: reset high speed USB device using ehci_hcd and address 3 [ 442.384348] usb 5-5: reset high speed USB device using ehci_hcd and address 3 [ 472.786034] usb 5-5: reset high speed USB device using ehci_hcd and address 3

[  482.114044] INFO: task modprobe:3945 blocked for more than 120 seconds.

[ 482.114053] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.

[  482.114059] modprobe      D 4c90becf     0  3945      1

[ 482.114068] f6cf0ea0 00000082 00000080 4c90becf 0000004e f6cf102c c1ff1fa0 00000000 [ 482.114088] f753dd70 f7b4abe8 000f3f73 00000000 f889ca71 f7b4ab80 f7b4ab80 f889cc0e [ 482.114106] 7fffffff 7fffffff f6943c1c 00000002 c02b7e69 00000086 c0129a63 00000000

[  482.114124] Call Trace:
[  482.114222]  [<f889ca71>] scsi_init_sgtable+0x55/0x7d [scsi_mod]
[  482.114269]  [<f889cc0e>] scsi_init_io+0x14/0x9e [scsi_mod]
[  482.114315]  [<c02b7e69>] schedule_timeout+0x13/0x86
[  482.114331]  [<c0129a63>] __mod_timer+0x99/0xa3
[  482.114395]  [<f889dbb0>] scsi_request_fn+0x2e6/0x32a [scsi_mod]
[  482.114437]  [<c02b758d>] wait_for_common+0xaf/0x10f
[  482.114467]  [<c011b61d>] default_wake_function+0x0/0x8
[  482.114506]  [<c01d49d0>] blk_execute_rq+0x83/0x96
[  482.114521]  [<c01d49e3>] blk_end_sync_rq+0x0/0x25
[  482.114534]  [<c010eea0>] smp_reschedule_interrupt+0xc/0x1e
[  482.114543]  [<c01042d4>] reschedule_interrupt+0x28/0x30
[  482.114607]  [<c01938e9>] bio_copy_kern+0xf1/0x156
[  482.114706]  [<f889cfc4>] scsi_execute+0xc5/0x103 [scsi_mod]
[  482.114764]  [<f889d086>] scsi_execute_req+0x84/0xa1 [scsi_mod]
[  482.114849]  [<f8eff4a6>] sd_read_capacity+0x9a/0x7fa [sd_mod]
[  482.114889]  [<c01299b0>] try_to_del_timer_sync+0x44/0x4a
[  482.114942]  [<c012968c>] process_timeout+0x0/0x5
[  482.115004]  [<f8f00065>] sd_revalidate_disk+0x45f/0xd06 [sd_mod]
[  482.115044]  [<c0134c00>] up+0x9/0x2a
[  482.117547]  [<f8f01e5d>] sd_probe+0x290/0x367 [sd_mod]
[  482.117608]  [<c023a425>] __driver_attach+0x0/0x55
[  482.117619]  [<c023a3ae>] driver_probe_device+0xb5/0x12c
[  482.117643]  [<c023a45c>] __driver_attach+0x37/0x55
[  482.117667]  [<c0239cef>] bus_for_each_dev+0x37/0x59
[  482.117710]  [<c023a249>] driver_attach+0x11/0x13
[  482.117719]  [<c023a425>] __driver_attach+0x0/0x55
[  482.117728]  [<c023a04c>] bus_add_driver+0x8a/0x1a6
[  482.117735]  [<c0122d63>] printk+0x14/0x18
[  482.117744]  [<c01dd803>] kset_find_obj+0xf/0x4b
[  482.117774]  [<c023a63d>] driver_register+0x6d/0xc1
[  482.117808]  [<f8ec107a>] init_sd+0x7a/0xd3 [sd_mod]
[  482.117833]  [<c013f3cc>] sys_init_module+0x184b/0x19bb
[  482.117979]  [<f8f70d58>] tun_chr_ioctl+0x4fe/0x5a1 [tun]
[  482.118000]  [<c0166149>] vma_link+0xa3/0xbd
[  482.118056]  [<f8899690>] scsi_set_medium_removal+0x0/0x64 [scsi_mod]
[  482.118161]  [<f8f70974>] tun_chr_ioctl+0x11a/0x5a1 [tun]
[  482.118187]  [<c0166ba8>] do_mmap_pgoff+0x266/0x2b9
[  482.118328]  [<c0103853>] sysenter_past_esp+0x78/0xb1
[  482.118419]  =======================

[ 503.092040] usb 5-5: reset high speed USB device using ehci_hcd and address 3 [ 533.393094] usb 5-5: reset high speed USB device using ehci_hcd and address 3

[  544.389775] INFO: task vol_id:4508 blocked for more than 120 seconds.

[ 544.389783] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.

[  544.389790] vol_id        D f771368c     0  4508      1

[ 544.389799] f77b20c0 00000086 f889c9e7 f771368c f6f7d000 f77b224c c1ffbfa0 00000001 [ 544.389819] ffffffff 00005e85 f8f0103c f77b224c 00000000 00000000 00000000 000000ff [ 544.389837] 7fffffff 7fffffff f53f9d14 00000002 c02b7e69 00000086 c0129a63 00000000

[  544.389855] Call Trace:
[  544.389908]  [<f889c9e7>] scsi_get_cmd_from_req+0x1b/0x41 [scsi_mod]
[  544.389980]  [<f8f0103c>] sd_prep_fn+0x52/0x780 [sd_mod]
[  544.390033]  [<c02b7e69>] schedule_timeout+0x13/0x86
[  544.390050]  [<c0129a63>] __mod_timer+0x99/0xa3
[  544.390101]  [<f889dbb0>] scsi_request_fn+0x2e6/0x32a [scsi_mod]
[  544.390150]  [<c02b758d>] wait_for_common+0xaf/0x10f
[  544.390172]  [<c011b61d>] default_wake_function+0x0/0x8
[  544.390217]  [<c01d49d0>] blk_execute_rq+0x83/0x96
[  544.390231]  [<c01d49e3>] blk_end_sync_rq+0x0/0x25
[  544.390245]  [<c0158911>] mempool_alloc+0x1c/0xba
[  544.390264]  [<c01dba6f>] cfq_set_request+0x0/0x269
[  544.390285]  [<c01cfe40>] elv_set_request+0x14/0x22
[  544.390305]  [<c01d22e6>] get_request+0x1e5/0x2c7
[  544.390359]  [<c01d2874>] get_request_wait+0x106/0x117
[  544.390424]  [<f889cfc4>] scsi_execute+0xc5/0x103 [scsi_mod]
[  544.390488]  [<f889d086>] scsi_execute_req+0x84/0xa1 [scsi_mod]
[  544.390580]  [<f8effd7b>] sd_revalidate_disk+0x175/0xd06 [sd_mod]
[  544.390713]  [<c0193d6e>] check_disk_change+0x39/0x57
[  544.390733]  [<f8f01838>] sd_open+0xce/0x152 [sd_mod]
[  544.390767]  [<c019435c>] do_open+0xb6/0x28f
[  544.391869]  [<c01946b0>] blkdev_open+0x0/0x4d
[  544.391878]  [<c01946d5>] blkdev_open+0x25/0x4d
[  544.391900]  [<c0172b77>] __dentry_open+0x10d/0x1fc
[  544.391938]  [<c0172c82>] nameidata_to_filp+0x1c/0x2c
[  544.391964]  [<c017d382>] do_filp_open+0x34f/0x684
[  544.392069]  [<c01dc96a>] _atomic_dec_and_lock+0x2a/0x44
[  544.392088]  [<c0182376>] dput+0x25/0xbb
[  544.392154]  [<c0172994>] do_sys_open+0x40/0xb0
[  544.392192]  [<c0172a48>] sys_open+0x1e/0x23
[  544.392218]  [<c0103853>] sysenter_past_esp+0x78/0xb1
[  544.392272]  [<c02b0000>] serial_pnp_probe+0xde/0x16b
[  544.392319]  =======================
[  544.392325] INFO: task vol_id:4518 blocked for more than 120 seconds.

[ 544.392329] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.

[  544.392334] vol_id        D f7713cac     0  4518      1

[ 544.392341] f5648ea0 00000082 f889c9e7 f7713cac f6da0c00 f564902c c1ffbfa0 00000001 [ 544.392356] ffffffff 00005e85 f8f0103c f564902c 00000000 00000000 00000000 000000ff [ 544.392371] 7fffffff 7fffffff f569bd14 00000002 c02b7e69 00000086 c0129a63 00000000

[  544.392386] Call Trace:
[  544.392415]  [<f889c9e7>] scsi_get_cmd_from_req+0x1b/0x41 [scsi_mod]
[  544.392505]  [<f8f0103c>] sd_prep_fn+0x52/0x780 [sd_mod]
[  544.392589]  [<c02b7e69>] schedule_timeout+0x13/0x86
[  544.392608]  [<c0129a63>] __mod_timer+0x99/0xa3
[  544.392690]  [<f889dbb0>] scsi_request_fn+0x2e6/0x32a [scsi_mod]
[  544.392729]  [<c02b758d>] wait_for_common+0xaf/0x10f
[  544.392752]  [<c011b61d>] default_wake_function+0x0/0x8
[  544.392789]  [<c01d49d0>] blk_execute_rq+0x83/0x96
[  544.392802]  [<c01d49e3>] blk_end_sync_rq+0x0/0x25
[  544.392815]  [<c0158911>] mempool_alloc+0x1c/0xba
[  544.392834]  [<c01dba6f>] cfq_set_request+0x0/0x269
[  544.392856]  [<c01cfe40>] elv_set_request+0x14/0x22
[  544.392874]  [<c01d22e6>] get_request+0x1e5/0x2c7
[  544.392925]  [<c01d2874>] get_request_wait+0x106/0x117
[  544.392992]  [<f889cfc4>] scsi_execute+0xc5/0x103 [scsi_mod]
[  544.393051]  [<f889d086>] scsi_execute_req+0x84/0xa1 [scsi_mod]
[  544.393136]  [<f8effd7b>] sd_revalidate_disk+0x175/0xd06 [sd_mod]
[  544.393264]  [<c0193d6e>] check_disk_change+0x39/0x57
[  544.393284]  [<f8f01838>] sd_open+0xce/0x152 [sd_mod]
[  544.393318]  [<c019435c>] do_open+0xb6/0x28f
[  544.393365]  [<c01946b0>] blkdev_open+0x0/0x4d
[  544.393373]  [<c01946d5>] blkdev_open+0x25/0x4d
[  544.393396]  [<c0172b77>] __dentry_open+0x10d/0x1fc
[  544.393433]  [<c0172c82>] nameidata_to_filp+0x1c/0x2c
[  544.393460]  [<c017d382>] do_filp_open+0x34f/0x684
[  544.393565]  [<c01dc96a>] _atomic_dec_and_lock+0x2a/0x44
[  544.393584]  [<c0182376>] dput+0x25/0xbb
[  544.393650]  [<c0172994>] do_sys_open+0x40/0xb0
[  544.393687]  [<c0172a48>] sys_open+0x1e/0x23
[  544.393714]  [<c0103853>] sysenter_past_esp+0x78/0xb1
[  544.393768]  [<c02b0000>] serial_pnp_probe+0xde/0x16b
[  544.393815]  =======================

[ 563.703961] usb 5-5: reset high speed USB device using ehci_hcd and address 3 [ 594.057498] usb 5-5: reset high speed USB device using ehci_hcd and address 3 [ 626.104211] usb 5-5: reset high speed USB device using ehci_hcd and address 3

-- Package-specific info:
** Version:

Linux version 2.6.26-1-686 (Debian 2.6.26-3) (wa...@debian.org) (gcc version 4.1.3 20080623 (prerelease) (Debian 4.1.2-23)) #1 SMP Wed Aug 20 12:56:41 UTC 2008

** Command line:
root=/dev/hda1 ro

** Not tainted

** Kernel log:
[ 1802.820595]  =======================

[ 1821.505370] usb 5-5: reset high speed USB device using ehci_hcd and address 3 [ 1851.805364] usb 5-5: reset high speed USB device using ehci_hcd and address 3 [ 1882.131627] usb 5-5: reset high speed USB device using ehci_hcd and address 3 [ 1912.998987] usb 5-5: reset high speed USB device using ehci_hcd and address 3 [ 1943.299712] usb 5-5: reset high speed USB device using ehci_hcd and address 3 [ 1973.600824] usb 5-5: reset high speed USB device using ehci_hcd and address 3

[ 1983.204856] INFO: task vol_id:4763 blocked for more than 120 seconds.

[ 1983.204864] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.

[ 1983.204868] vol_id        D f5b2d68c     0  4763      1

[ 1983.204874] f5a1e4e0 00000082 f889cc0e f5b2d68c f6923a80 f5a1e66c c1ff1fa0 00000000 [ 1983.204886] ffffffff 0005c2a4 f8f0103c f6f94900 00000000 00000000 00000000 000000ff [ 1983.204897] 7fffffff 7fffffff f5a41ca0 00000002 c02b7e69 00000086 c0129a63 00000000

[ 1983.204908] Call Trace:
[ 1983.204948]  [<f889cc0e>] scsi_init_io+0x14/0x9e [scsi_mod]
[ 1983.205001]  [<f8f0103c>] sd_prep_fn+0x52/0x780 [sd_mod]
[ 1983.205041]  [<c02b7e69>] schedule_timeout+0x13/0x86
[ 1983.205053]  [<c0129a63>] __mod_timer+0x99/0xa3
[ 1983.205092]  [<f889dbb0>] scsi_request_fn+0x2e6/0x32a [scsi_mod]
[ 1983.205122]  [<c02b758d>] wait_for_common+0xaf/0x10f
[ 1983.205139]  [<c011b61d>] default_wake_function+0x0/0x8
[ 1983.205168]  [<c01d49d0>] blk_execute_rq+0x83/0x96
[ 1983.205177]  [<c01d49e3>] blk_end_sync_rq+0x0/0x25
[ 1983.205215]  [<c019311b>] bio_add_pc_page+0x16/0x1b
[ 1983.205241]  [<c0193872>] bio_copy_kern+0x7a/0x156
[ 1983.205315]  [<f889cfc4>] scsi_execute+0xc5/0x103 [scsi_mod]
[ 1983.205356]  [<f889d086>] scsi_execute_req+0x84/0xa1 [scsi_mod]
[ 1983.205419]  [<f8eff4a6>] sd_read_capacity+0x9a/0x7fa [sd_mod]
[ 1983.205447]  [<c01299b0>] try_to_del_timer_sync+0x44/0x4a
[ 1983.205490]  [<c012968c>] process_timeout+0x0/0x5
[ 1983.205535]  [<f8f00065>] sd_revalidate_disk+0x45f/0xd06 [sd_mod]
[ 1983.205571]  [<c0175ea7>] get_super+0x15/0x7a
[ 1983.205613]  [<c01a834c>] rescan_partitions+0x69/0x249
[ 1983.205633]  [<c0193d6e>] check_disk_change+0x39/0x57
[ 1983.205646]  [<f8f018a2>] sd_open+0x138/0x152 [sd_mod]
[ 1983.205670]  [<c0194491>] do_open+0x1eb/0x28f
[ 1983.205705]  [<c01946b0>] blkdev_open+0x0/0x4d
[ 1983.205710]  [<c01946d5>] blkdev_open+0x25/0x4d
[ 1983.205725]  [<c0172b77>] __dentry_open+0x10d/0x1fc
[ 1983.205752]  [<c0172c82>] nameidata_to_filp+0x1c/0x2c
[ 1983.205772]  [<c017d382>] do_filp_open+0x34f/0x684
[ 1983.208164]  [<c0197839>] inotify_dentry_parent_queue_event+0x59/0x72
[ 1983.208200]  [<c01dc96a>] _atomic_dec_and_lock+0x2a/0x44
[ 1983.208225]  [<c0182376>] dput+0x25/0xbb
[ 1983.208331]  [<c0172994>] do_sys_open+0x40/0xb0
[ 1983.208388]  [<c0172a48>] sys_open+0x1e/0x23
[ 1983.208428]  [<c0103853>] sysenter_past_esp+0x78/0xb1
[ 1983.208484]  [<c02b0000>] serial_pnp_probe+0xde/0x16b
[ 1983.208530]  =======================

[ 1983.208537] INFO: task hald-addon-stor:4768 blocked for more than 120 seconds. [ 1983.208542] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.

[ 1983.208546] hald-addon-st D f5b2d5c8     0  4768   4154

[ 1983.208553] f5a5f2c0 00000082 f889c9e7 f5b2d5c8 f6ea8000 f5a5f44c c1ffbfa0 00000001 [ 1983.208568] ffffffff 0005c2a3 f8f0103c 7fffffff 00000000 00000000 00000000 000000ff [ 1983.208583] 7fffffff 7fffffff f5ba1d2c 00000002 c02b7e69 00000086 c0129a63 00000000

[ 1983.208598] Call Trace:
[ 1983.208616]  [<f889c9e7>] scsi_get_cmd_from_req+0x1b/0x41 [scsi_mod]
[ 1983.208676]  [<f8f0103c>] sd_prep_fn+0x52/0x780 [sd_mod]
[ 1983.208730]  [<c02b7e69>] schedule_timeout+0x13/0x86
[ 1983.208745]  [<c0129a63>] __mod_timer+0x99/0xa3
[ 1983.208795]  [<f889dbb0>] scsi_request_fn+0x2e6/0x32a [scsi_mod]
[ 1983.208839]  [<c02b758d>] wait_for_common+0xaf/0x10f
[ 1983.208861]  [<c011b61d>] default_wake_function+0x0/0x8
[ 1983.208901]  [<c01d49d0>] blk_execute_rq+0x83/0x96
[ 1983.208914]  [<c01d49e3>] blk_end_sync_rq+0x0/0x25
[ 1983.208926]  [<c0158911>] mempool_alloc+0x1c/0xba
[ 1983.208935]  [<c01cfe40>] elv_set_request+0x14/0x22
[ 1983.208949]  [<c01dba6f>] cfq_set_request+0x0/0x269
[ 1983.208971]  [<c01cfe40>] elv_set_request+0x14/0x22
[ 1983.208989]  [<c01d22e6>] get_request+0x1e5/0x2c7
[ 1983.209041]  [<c01d2874>] get_request_wait+0x106/0x117
[ 1983.209110]  [<f889cfc4>] scsi_execute+0xc5/0x103 [scsi_mod]
[ 1983.209157]  [<f889d086>] scsi_execute_req+0x84/0xa1 [scsi_mod]
[ 1983.209157]  [<f889d0ee>] scsi_test_unit_ready+0x4b/0xaa [scsi_mod]
[ 1983.209157]  [<f8f02004>] sd_media_changed+0xd0/0x170 [sd_mod]
[ 1983.209157]  [<c0193d48>] check_disk_change+0x13/0x57
[ 1983.209157]  [<f8f01838>] sd_open+0xce/0x152 [sd_mod]
[ 1983.209157]  [<c019435c>] do_open+0xb6/0x28f
[ 1983.209157]  [<c01946b0>] blkdev_open+0x0/0x4d
[ 1983.209157]  [<c01946d5>] blkdev_open+0x25/0x4d
[ 1983.209157]  [<c0172b77>] __dentry_open+0x10d/0x1fc
[ 1983.209157]  [<c0172c82>] nameidata_to_filp+0x1c/0x2c
[ 1983.209157]  [<c017d382>] do_filp_open+0x34f/0x684
[ 1983.209157]  [<f894fa43>] ide_set_handler+0x2c/0x3e [ide_core]
[ 1983.209157]  [<f896701a>] cdrom_newpc_intr+0x4c1/0x54d [ide_cd_mod]
[ 1983.209157]  [<f89651bd>] cdrom_timer_expiry+0x0/0x4b [ide_cd_mod]
[ 1983.209157]  [<f8966b59>] cdrom_newpc_intr+0x0/0x54d [ide_cd_mod]
[ 1983.209157]  [<c0172994>] do_sys_open+0x40/0xb0
[ 1983.209157]  [<c0172a48>] sys_open+0x1e/0x23
[ 1983.209157]  [<c0103853>] sysenter_past_esp+0x78/0xb1
[ 1983.209157]  =======================

[ 2003.902564] usb 5-5: reset high speed USB device using ehci_hcd and address 3 [ 2034.203460] usb 5-5: reset high speed USB device using ehci_hcd and address 3

[ 2034.395445] sd 2:0:0:2: [sdc] READ CAPACITY failed

[ 2034.395445] sd 2:0:0:2: [sdc] Result: hostbyte=DID_ABORT driverbyte=DRIVER_SENSE,SUGGEST_OK

[ 2034.395445] sd 2:0:0:2: [sdc] Sense Key : Not Ready [current]

[ 2034.395445] sd 2:0:0:2: [sdc] Add. Sense: Logical unit is in process of becoming ready

[ 2034.399447] sd 2:0:0:2: [sdc] Write Protect is off
[ 2034.399447] sd 2:0:0:2: [sdc] Mode Sense: 00 00 00 00
[ 2034.399447] sd 2:0:0:2: [sdc] Assuming drive cache: write through

** Loaded modules:
Module                  Size  Used by
binfmt_misc             7528  1
i915                   25280  2
drm                    65256  3 i915
rfcomm                 28272  0
l2cap                  17248  5 rfcomm
bluetooth              44900  4 rfcomm,l2cap
tun                     8292  1
irda                   95480  0
crc_ccitt               2080  1 irda
sd_mod                 22200  0
ppdev                   6468  0
lp                      8164  0
usb_storage            75712  0
video                  16400  0
output                  2912  1 video
ac                      3264  0
battery                 6272  0
nfsd                  186704  4
auth_rpcgss            33952  1 nfsd
exportfs                3904  1 nfsd
nfs                   213896  0
lockd                  54248  2 nfsd,nfs
nfs_acl                 2912  2 nfsd,nfs
sunrpc                162176  9 nfsd,auth_rpcgss,nfs,lockd,nfs_acl
ipv6                  235172  36
nf_conntrack_ipv4      12268  5
xt_state                2016  5
iptable_mangle          2688  1
xt_u32                  2080  0
xt_time                 2528  0
xt_tcpudp               2816  17
xt_tcpmss               1984  0
xt_string               1984  0
xt_statistic            1956  0
xt_sctp                 2624  0
xt_realm                1536  0
xt_rateest              2336  0
xt_quota                1892  0
xt_policy               2848  0
xt_pkttype              1728  0
xt_physdev              2352  0
xt_owner                2560  1
xt_multiport            2816  0
xt_mark                 1952  0
xt_mac                  1728  0
xt_limit                2180  0
xt_length               1760  0
xt_iprange              2272  0
xt_esp                  1824  0
xt_dscp                 2368  0
xt_dccp                 2696  0
xt_connlimit            3720  0
xt_comment              1664  0
xt_TRACE                1632  0
xt_TCPOPTSTRIP          2272  0
xt_TCPMSS               3616  0
xt_SECMARK              2532  0
xt_RATEEST              3712  1 xt_rateest
xt_NFQUEUE              1792  0
xt_NFLOG                1824  0
xt_MARK                 2304  14
xt_DSCP                 2944  0
xt_CLASSIFY             1696  0
nfnetlink_queue         7620  0
nfnetlink_log           7556  0
nfnetlink               3928  2 nfnetlink_queue,nfnetlink_log
cls_fw                  3840  0
sch_cbq                12896  0
sch_gred                6208  0
sch_red                 4800  0
sch_sfq                 5472  0
fuse                   42908  1
dm_crypt               11172  0
crypto_blkcipher       15236  1 dm_crypt
dm_snapshot            14340  0
dm_mirror              15104  0
dm_log                  8452  1 dm_mirror
dm_mod                 46184  4 dm_crypt,dm_snapshot,dm_mirror,dm_log
iptable_filter          2624  1
ip_tables              10160  2 iptable_mangle,iptable_filter

x_tables 13284 37 xt_state,xt_u32,xt_time,xt_tcpudp,xt_tcpmss,xt_string,xt_statistic,xt_sctp,xt_realm,xt_rateest,xt_quota,xt_policy,xt_pkttype,xt_physdev,xt_owner,xt_multiport,xt_mark,xt_mac,xt_limit,xt_length,xt_iprange,xt_esp,xt_dscp,xt_dccp,xt_connlimit,xt_comment,xt_TRACE,xt_TCPOPTSTRIP,xt_TCPMSS,xt_SECMARK,xt_RATEEST,xt_NFQUEUE,xt_NFLOG,xt_MARK,xt_DSCP,xt_CLASSIFY,ip_tables

nf_conntrack_sip       16092  0

nf_conntrack 55508 4 nf_conntrack_ipv4,xt_state,xt_connlimit,nf_conntrack_sip

loop                   12748  0
snd_usb_audio          70272  0
snd_usb_lib            13440  1 snd_usb_audio
snd_seq_dummy           2660  0
snd_seq_oss            24992  0
snd_intel8x0           26268  1
snd_seq_midi            5728  0
snd_seq_midi_event      6432  2 snd_seq_oss,snd_seq_midi

snd_seq 41456 7 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event

tda9875                 6192  0
snd_ac97_codec         88484  1 snd_intel8x0
ac97_bus                1728  1 snd_ac97_codec
snd_pcm_oss            32800  0
bttv                  148116  0
snd_mixer_oss          12320  1 snd_pcm_oss
videodev               27520  1 bttv
v4l1_compat            12260  1 videodev
firmware_class          6816  1 bttv
ir_common              39620  1 bttv
compat_ioctl32          1312  1 bttv
i2c_algo_bit            5188  1 bttv
v4l2_common            10240  1 bttv
videobuf_dma_sg        11140  1 bttv
videobuf_core          16100  2 bttv,videobuf_dma_sg
btcx_risc               4264  1 bttv
snd_rawmidi            18560  2 snd_usb_lib,snd_seq_midi

snd_pcm 62628 4 snd_usb_audio,snd_intel8x0,snd_ac97_codec,snd_pcm_oss

tveeprom               10980  1 bttv
parport_serial          5920  0
parport_pc             22500  3 parport_serial
parport                30988  3 ppdev,lp,parport_pc

snd_seq_device 6380 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq,snd_rawmidi

snd_hwdep               6212  1 snd_usb_audio
snd_timer              17800  2 snd_seq,snd_pcm
snd_page_alloc          7816  2 snd_intel8x0,snd_pcm
i2c_i801                7920  0

i2c_core 19828 6 tda9875,bttv,i2c_algo_bit,v4l2_common,tveeprom,i2c_i801

rng_core                3940  0

snd 45604 15 snd_usb_audio,snd_seq_oss,snd_intel8x0,snd_seq,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_rawmidi,snd_pcm,snd_seq_device,snd_hwdep,snd_timer

pcspkr                  2432  0
iTCO_wdt                9508  0
soundcore               6368  1 snd
shpchp                 25528  0
button                  6064  0
pci_hotplug            23460  1 shpchp
intel_agp              22300  1
agpgart                28776  3 drm,intel_agp
joydev                  8480  0
evdev                   8000  4
reiserfs              189920  1
ide_disk               10496  3
ide_cd_mod             27684  0
cdrom                  30176  1 ide_cd_mod
usbhid                 35904  0
hid                    33184  1 usbhid
ff_memless              4392  1 usbhid
8139cp                 16800  0
ata_piix               14180  0
piix                    6568  0 [permanent]
ide_pci_generic         3908  0 [permanent]
ide_core               92628  4 ide_disk,ide_cd_mod,piix,ide_pci_generic
floppy                 47716  0
8139too                20320  0
mii                     4896  2 8139cp,8139too
ehci_hcd               28428  0
ata_generic             4676  0
libata                140416  2 ata_piix,ata_generic
scsi_mod              129356  3 sd_mod,usb_storage,libata
dock                    8272  1 libata
uhci_hcd               18672  0
e1000                 102624  0

usbcore 118160 7 usb_storage,snd_usb_audio,snd_usb_lib,usbhid,ehci_hcd,uhci_hcd

thermal                15228  0
processor              32576  1 thermal
fan                     4164  0
thermal_sys            10856  4 video,thermal,processor,fan

** PCI devices:

00:00.0 Host bridge [0600]: Intel Corporation 82865G/PE/P DRAM Controller/Host-Hub Interface [8086:2570] (rev 02) Subsystem: Intel Corporation 82865G/PE/P DRAM Controller/Host-Hub Interface [8086:2570] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-

   Latency: 0
   Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
   Capabilities: <access denied>
   Kernel driver in use: agpgart-intel
   Kernel modules: intel-agp

00:02.0 VGA compatible controller [0300]: Intel Corporation 82865G Integrated Graphics Controller [8086:2572] (rev 02)

   Subsystem: Intel Corporation Device [8086:4246]

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

   Latency: 0
   Interrupt: pin A routed to IRQ 16
   Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
   Region 1: Memory at ffa80000 (32-bit, non-prefetchable) [size=512K]
   Region 2: I/O ports at ec00 [size=8]
   Capabilities: <access denied>
   Kernel modules: intelfb

00:03.0 PCI bridge [0604]: Intel Corporation 82865G/PE/P PCI to CSA Bridge [8086:2573] (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

   Latency: 32
   Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
   I/O behind bridge: 00009000-00009fff
   Memory behind bridge: ff700000-ff7fffff

Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-

   BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
       PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
   Kernel modules: shpchp

00:1d.0 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1 [8086:24d2] (rev 02)

   Subsystem: Intel Corporation Device [8086:4246]

Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

   Latency: 0
   Interrupt: pin A routed to IRQ 16
   Region 4: I/O ports at c800 [size=32]
   Kernel driver in use: uhci_hcd
   Kernel modules: uhci-hcd

00:1d.1 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2 [8086:24d4] (rev 02)

   Subsystem: Intel Corporation Device [8086:4246]

Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

   Latency: 0
   Interrupt: pin B routed to IRQ 19
   Region 4: I/O ports at cc00 [size=32]
   Kernel driver in use: uhci_hcd
   Kernel modules: uhci-hcd

00:1d.2 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #3 [8086:24d7] (rev 02)

   Subsystem: Intel Corporation Device [8086:4246]

Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

   Latency: 0
   Interrupt: pin C routed to IRQ 18
   Region 4: I/O ports at d000 [size=32]
   Kernel driver in use: uhci_hcd
   Kernel modules: uhci-hcd

00:1d.3 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #4 [8086:24de] (rev 02)

   Subsystem: Intel Corporation Device [8086:4246]

Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

   Latency: 0
   Interrupt: pin A routed to IRQ 16
   Region 4: I/O ports at d400 [size=32]
   Kernel driver in use: uhci_hcd
   Kernel modules: uhci-hcd

00:1d.7 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller [8086:24dd] (rev 02) (prog-if 20)

   Subsystem: Intel Corporation Device [8086:4246]

Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

   Latency: 0
   Interrupt: pin D routed to IRQ 23
   Region 0: Memory at ffa7fc00 (32-bit, non-prefetchable) [size=1K]
   Capabilities: <access denied>
   Kernel driver in use: ehci_hcd
   Kernel modules: ehci-hcd

00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev c2) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

   Latency: 0
   Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
   I/O behind bridge: 0000a000-0000bfff
   Memory behind bridge: ff800000-ff8fffff
   Prefetchable memory behind bridge: e6a00000-e6afffff

Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-

   BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
       PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
   Kernel modules: shpchp

00:1f.0 ISA bridge [0601]: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge [8086:24d0] (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

   Latency: 0
   Kernel modules: intel-rng, iTCO_wdt

00:1f.1 IDE interface [0101]: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE Controller [8086:24db] (rev 02) (prog-if 8a [Master SecP PriP])

   Subsystem: Intel Corporation Device [8086:4246]

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

   Latency: 0
   Interrupt: pin A routed to IRQ 18
   Region 0: I/O ports at 01f0 [size=8]
   Region 1: I/O ports at 03f4 [size=1]
   Region 2: I/O ports at 0170 [size=8]
   Region 3: I/O ports at 0374 [size=1]
   Region 4: I/O ports at ffa0 [size=16]
   Region 5: Memory at 80000000 (32-bit, non-prefetchable) [size=1K]
   Kernel driver in use: PIIX_IDE
   Kernel modules: piix

00:1f.2 IDE interface [0101]: Intel Corporation 82801EB (ICH5) SATA Controller [8086:24d1] (rev 02) (prog-if 8f [Master SecP SecO PriP PriO])

   Subsystem: Intel Corporation Device [8086:4246]

Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

   Latency: 0
   Interrupt: pin A routed to IRQ 18
   Region 0: I/O ports at e800 [size=8]
   Region 1: I/O ports at e400 [size=4]
   Region 2: I/O ports at e000 [size=8]
   Region 3: I/O ports at dc00 [size=4]
   Region 4: I/O ports at d800 [size=16]
   Kernel driver in use: ata_piix
   Kernel modules: ata_piix

00:1f.3 SMBus [0c05]: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus Controller [8086:24d3] (rev 02)

   Subsystem: Intel Corporation Device [8086:4246]

Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

   Interrupt: pin B routed to IRQ 17
   Region 4: I/O ports at c400 [size=32]
   Kernel driver in use: i801_smbus
   Kernel modules: i2c-i801

00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801EB/ER (ICH5/ICH5R) AC'97 Audio Controller [8086:24d5] (rev 02)

   Subsystem: Intel Corporation Device [8086:e001]

Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

   Latency: 0
   Interrupt: pin B routed to IRQ 17
   Region 2: Memory at ffa7f800 (32-bit, non-prefetchable) [size=512]
   Region 3: Memory at ffa7f400 (32-bit, non-prefetchable) [size=256]
   Capabilities: <access denied>
   Kernel driver in use: Intel ICH
   Kernel modules: snd-intel8x0

01:01.0 Ethernet controller [0200]: Intel Corporation 82547EI Gigabit Ethernet Controller [8086:1019]

   Subsystem: Intel Corporation Device [8086:302c]

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+

   Latency: 0 (63750ns min), Cache Line Size: 64 bytes
   Interrupt: pin A routed to IRQ 18
   Region 0: Memory at ff7e0000 (32-bit, non-prefetchable) [size=128K]
   Region 2: I/O ports at 9c00 [size=32]
   Capabilities: <access denied>
   Kernel driver in use: e1000
   Kernel modules: e1000

02:00.0 Multimedia video controller [0400]: Brooktree Corporation Bt878 Video Capture [109e:036e] (rev 11) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

   Latency: 32 (4000ns min, 10000ns max)
   Interrupt: pin A routed to IRQ 21
   Region 0: Memory at e6afe000 (32-bit, prefetchable) [size=4K]
   Capabilities: <access denied>
   Kernel driver in use: bttv
   Kernel modules: bttv

02:00.1 Multimedia controller [0480]: Brooktree Corporation Bt878 Audio Capture [109e:0878] (rev 11) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

   Latency: 32 (1000ns min, 63750ns max)
   Interrupt: pin A routed to IRQ 11
   Region 0: Memory at e6aff000 (32-bit, prefetchable) [size=4K]
   Capabilities: <access denied>

02:02.0 Communication controller [0780]: NetMos Technology PCI 9835 Multi-I/O Controller [9710:9835] (rev 01)

   Subsystem: LSI Logic / Symbios Logic Device [1000:0012]

Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

   Interrupt: pin A routed to IRQ 17
   Region 0: I/O ports at bc00 [size=8]
   Region 1: I/O ports at b800 [size=8]
   Region 2: I/O ports at b400 [size=8]
   Region 3: I/O ports at b000 [size=8]
   Region 4: I/O ports at ac00 [size=8]
   Region 5: I/O ports at a800 [size=16]
   Kernel driver in use: parport_serial
   Kernel modules: parport_serial

02:04.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)

   Subsystem: Surecom Technology Device [10bd:0320]

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

   Latency: 32 (8000ns min, 16000ns max)
   Interrupt: pin A routed to IRQ 18
   Region 0: I/O ports at a400 [size=256]
   Region 1: Memory at ff8ffc00 (32-bit, non-prefetchable) [size=256]
   Capabilities: <access denied>
   Kernel driver in use: 8139too
   Kernel modules: 8139too, 8139cp

02:05.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

   Latency: 32 (8000ns min, 16000ns max)
   Interrupt: pin A routed to IRQ 17
   Region 0: I/O ports at a000 [size=256]
   Region 1: Memory at ff8ff800 (32-bit, non-prefetchable) [size=256]
   Capabilities: <access denied>
   Kernel driver in use: 8139too
   Kernel modules: 8139too, 8139cp



-- System Information:
Debian Release: lenny/sid
 APT prefers testing
 APT policy: (1001, 'testing'), (100, 'stable'), (50, 'unstable')
Architecture: i386 (i686)

Kernel: Linux 2.6.26-1-686 (SMP w/2 CPU cores)
Locale: LANG=pl_PL.UTF-8, LC_CTYPE=pl_PL.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash

Versions of packages linux-image-2.6.26-1-686 depends on:

ii debconf [debconf-2.0] 1.5.22 Debian configuration management sy ii initramfs-tools [linux-initra 0.92f tools for generating an initramfs ii module-init-tools 3.4-1 tools for managing Linux kernel mo

Versions of packages linux-image-2.6.26-1-686 recommends:

ii libc6-i686 2.7-13 GNU C Library: Shared libraries [i

Versions of packages linux-image-2.6.26-1-686 suggests:

ii grub 0.97-46 GRand Unified Bootloader (Legacy v

pn  linux-doc-2.6.26              <none>     (no description available)

-- debconf information:
 linux-image-2.6.26-1-686/preinst/abort-overwrite-2.6.26-1-686:
 linux-image-2.6.26-1-686/postinst/bootloader-error-2.6.26-1-686:
 linux-image-2.6.26-1-686/postinst/depmod-error-initrd-2.6.26-1-686: false
 linux-image-2.6.26-1-686/postinst/old-system-map-link-2.6.26-1-686: true

linux-image-2.6.26-1-686/prerm/would-invalidate-boot-loader-2.6.26-1-686: true

 linux-image-2.6.26-1-686/preinst/elilo-initrd-2.6.26-1-686: true
 linux-image-2.6.26-1-686/postinst/old-dir-initrd-link-2.6.26-1-686: true
 linux-image-2.6.26-1-686/postinst/kimage-is-a-directory:
 linux-image-2.6.26-1-686/postinst/create-kimage-link-2.6.26-1-686: true
 linux-image-2.6.26-1-686/preinst/overwriting-modules-2.6.26-1-686: true
 linux-image-2.6.26-1-686/postinst/depmod-error-2.6.26-1-686: false
 shared/kernel-image/really-run-bootloader: true
 linux-image-2.6.26-1-686/prerm/removing-running-kernel-2.6.26-1-686: true
 linux-image-2.6.26-1-686/preinst/abort-install-2.6.26-1-686:
 linux-image-2.6.26-1-686/preinst/lilo-has-ramdisk:
 linux-image-2.6.26-1-686/preinst/bootloader-initrd-2.6.26-1-686: true
 linux-image-2.6.26-1-686/preinst/lilo-initrd-2.6.26-1-686: true
 linux-image-2.6.26-1-686/postinst/old-initrd-link-2.6.26-1-686: true
 linux-image-2.6.26-1-686/postinst/bootloader-test-error-2.6.26-1-686:
 linux-image-2.6.26-1-686/preinst/failed-to-move-modules-2.6.26-1-686:
 linux-image-2.6.26-1-686/preinst/initrd-2.6.26-1-686:

--- End Message ---

--- Begin Message ---

Version: 2.6.30-1

On Wed, Oct 07, 2009 at 10:14:23PM +0200, Gilles Mocellin wrote:
> On Wed, Oct 07, 2009 at 09:32:56PM +0200, Moritz Muehlenhoff wrote:
> > On Sat, Oct 04, 2008 at 06:10:11PM +0200, Gilles Mocellin wrote:
> > > At least on Asus Eeepc 701, the SD card reader seems not a true SDHC 
> > > reader.
> > > But it works with the default OS.
> > > 
> > > It even has worked on mine two times, I don't know why it suddenly breaks.
> > 
> > Did you try more recent kernels? Do they fix the problem?
> > 
> > Cheers,
> >         Moritz
> 
> Yes. As I'm running Debian unstable, I run 2.6.30 now.
> The SD card reader works since some time now, I can't remember which
> kernel made it work... Perhaps a recent 2.6.26 from lenny updates works.

Thanks for the feedback, marking 2.6.30 as fixed.

Cheers,
        Moritz

--- End Message ---