--- Begin Message ---
Package: linux-image-2.6.26-2-686
Version: 2.6.26-17
Severity: important
My cdrom drive (Plextor PX-755A) doesn't work on the motherboard
Gigabyte EP35-DS3. In syslog I've these traces:
kernel: [ 5.582896] hda: PLEXTOR DVDR PX-755A, ATAPI CD/DVD-ROM drive
kernel: [ 5.907166] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
kernel: [ 5.907166] hda: UDMA/66 mode selected
kernel: [ 34.651175] hda: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
kernel: [ 38.279181] hda: UDMA/66 mode selected
kernel: [ 40.902511] hda: UDMA/66 mode selected
kernel: [ 99.618012] hda: ide_cd_check_ireason: wrong transfer direction!
kernel: [ 132.441139] hda: packet command error: status=0xd0 { Busy }
kernel: [ 132.441144] ide: failed opcode was: unknown
-- Package-specific info:
** Version:
Linux version 2.6.26-2-686 (Debian 2.6.26-17) (da...@debian.org) (gcc version
4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Sun Jun 21 04:57:38 UTC
2009
** Command line:
root=UUID=6e488276-eb28-4ee4-ab35-da7cebf31b15 ro
** Tainted: P (1)
** Kernel log:
[ 38.753630] logips2pp: Detected unknown logitech mouse model 63
[ 38.875919] 5:3:1: cannot get freq at ep 0x84
[ 38.895919] usbcore: registered new interface driver snd-usb-audio
[ 38.995392] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) ->
IRQ 22
[ 38.995483] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 39.296302] input: ImExPS/2 Logitech Explorer Mouse as /class/input/input6
[ 39.734194] Adding 2096472k swap on /dev/sde2. Priority:-1 extents:1
across:2096472k
[ 39.944745] EXT3 FS on sde3, internal journal
[ 40.761478] it87: Found IT8718F chip at 0x290, revision 4
[ 40.761478] it87: in3 is VCC (+5V)
[ 40.777919] coretemp coretemp.0: Using relative temperature scale!
[ 40.777919] coretemp coretemp.1: Using relative temperature scale!
[ 40.790955] sd 6:0:0:0: Attached scsi generic sg0 type 0
[ 40.791009] sd 6:0:0:1: Attached scsi generic sg1 type 0
[ 40.791062] sd 6:0:0:2: Attached scsi generic sg2 type 0
[ 40.791114] sd 6:0:0:3: Attached scsi generic sg3 type 0
[ 40.791166] sd 9:0:0:0: Attached scsi generic sg4 type 0
[ 40.791218] sd 9:0:2:0: Attached scsi generic sg5 type 0
[ 40.805120] Floppy drive(s): fd0 is 1.44M
[ 40.832619] FDC 0 is a post-1991 82077
[ 40.902511] hda: UDMA/66 mode selected
[ 42.322973] fuse init (API version 7.9)
[ 42.434975] kjournald starting. Commit interval 5 seconds
[ 42.442975] EXT3 FS on sdf1, internal journal
[ 42.442975] EXT3-fs: mounted filesystem with ordered data mode.
[ 42.446976] kjournald starting. Commit interval 5 seconds
[ 42.446976] EXT3 FS on sde7, internal journal
[ 42.446976] EXT3-fs: mounted filesystem with ordered data mode.
[ 42.470158] kjournald starting. Commit interval 5 seconds
[ 42.470158] EXT3 FS on sde5, internal journal
[ 42.470158] EXT3-fs: mounted filesystem with ordered data mode.
[ 42.474974] kjournald starting. Commit interval 5 seconds
[ 42.474987] EXT3 FS on sde6, internal journal
[ 42.474987] EXT3-fs: mounted filesystem with ordered data mode.
[ 44.945432] skge lan: enabling interface
[ 45.372173] r8169: adsl: link up
[ 45.372173] r8169: adsl: link up
[ 45.430585] NET: Registered protocol family 10
[ 45.430899] lo: Disabled Privacy Extensions
[ 45.431408] ADDRCONF(NETDEV_UP): lan: link is not ready
[ 47.038694] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 47.061164] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 49.528268] RPC: Registered udp transport module.
[ 49.528268] RPC: Registered tcp transport module.
[ 49.606257] Installing knfsd (copyright (C) 1996 o...@monad.swb.de).
[ 49.754269] ttyS0: LSR safety check engaged!
[ 49.754269] ttyS0: LSR safety check engaged!
[ 49.754269] ttyS1: LSR safety check engaged!
[ 49.754269] ttyS1: LSR safety check engaged!
[ 57.344287] adsl: no IPv6 routers present
[ 60.911289] /dev/vmmon[3952]: Module vmmon: registered with major=10
minor=165
[ 60.911289] /dev/vmmon[3952]: Initial HV check: anyNotCapable=0
anyUnlocked=0 anyEnabled=1 anyDisabled=0
[ 60.911289] /dev/vmmon[3952]: HV check: anyNotCapable=0 anyUnlocked=0
anyEnabled=1 anyDisabled=0
[ 60.911289] /dev/vmmon[3952]: Module vmmon: initialized
[ 60.928184] /dev/vmci[3973]: VMCI: Driver initialized.
[ 60.928184] /dev/vmci[3973]: Module vmci: registered with major=10 minor=59
[ 60.928184] /dev/vmci[3973]: Module vmci: initialized
[ 61.165607] /dev/vmnet: open called by PID 4058 (vmnet-bridge)
[ 61.165607] /dev/vmnet: hub 0 does not exist, allocating memory.
[ 61.165607] /dev/vmnet: port on hub 0 successfully opened
[ 61.165607] bridge-adsl: up
[ 61.165607] bridge-adsl: attached
[ 63.666909] /dev/vmnet: open called by PID 4571 (vmnet-dhcpd)
[ 63.666909] /dev/vmnet: hub 8 does not exist, allocating memory.
[ 63.666909] /dev/vmnet: port on hub 8 successfully opened
[ 63.722046] /dev/vmnet: open called by PID 4573 (vmnet-natd)
[ 63.722053] /dev/vmnet: port on hub 8 successfully opened
[ 63.742908] /dev/vmnet: open called by PID 4577 (vmnet-netifup)
[ 63.742908] /dev/vmnet: port on hub 8 successfully opened
[ 68.732297] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery
directory
[ 68.734839] NFSD: starting 90-second grace period
[ 74.166643] ttyS0: LSR safety check engaged!
[ 74.166643] ttyS1: LSR safety check engaged!
[ 74.581252] Bluetooth: Core ver 2.11
[ 74.581252] NET: Registered protocol family 31
[ 74.581252] Bluetooth: HCI device and connection manager initialized
[ 74.581252] Bluetooth: HCI socket layer initialized
[ 74.601253] Bluetooth: L2CAP ver 2.9
[ 74.601253] Bluetooth: L2CAP socket layer initialized
[ 74.625251] Bluetooth: RFCOMM socket layer initialized
[ 74.625251] Bluetooth: RFCOMM TTY layer initialized
[ 74.625251] Bluetooth: RFCOMM ver 1.8
[ 74.797043] Bluetooth: SCO (Voice Link) ver 0.5
[ 74.797043] Bluetooth: SCO socket layer initialized
[ 74.960545] Bluetooth: BNEP (Ethernet Emulation) ver 1.2
[ 74.960545] Bluetooth: BNEP filters: protocol multicast
[ 75.085314] Bridge firewalling registered
[ 75.085314] pan0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
[ 77.645534] nvidia: module license 'NVIDIA' taints kernel.
[ 77.897214] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) ->
IRQ 16
[ 77.897214] PCI: Setting latency timer of device 0000:01:00.0 to 64
[ 77.897214] NVRM: loading NVIDIA UNIX x86 Kernel Module 173.14.09 Wed Jun
4 23:43:17 PDT 2008
[ 78.850321] lp: driver loaded but no devices found
[ 78.862085] ppdev: user-space parallel port driver
[ 91.934723] 5:3:1: cannot get freq at ep 0x84
[ 91.963062] 5:3:1: cannot get freq at ep 0x84
[ 91.999206] 5:3:1: cannot get freq at ep 0x84
[ 99.618012] hda: ide_cd_check_ireason: wrong transfer direction!
[ 132.441139] hda: packet command error: status=0xd0 { Busy }
[ 132.441144] ide: failed opcode was: unknown
** Loaded modules:
Module Size Used by
binfmt_misc 7528 1
ppdev 6500 0
lp 8164 0
nvidia 7086148 24
bridge 40024 0
bnep 10304 2
sco 8640 2
rfcomm 28272 0
l2cap 17248 4 bnep,rfcomm
bluetooth 44868 6 bnep,sco,rfcomm,l2cap
vmnet 33632 9
parport_pc 22500 0
parport 30988 3 ppdev,lp,parport_pc
vmblock 11652 3
vmci 44052 0
vmmon 60400 0
acpi_cpufreq 6796 0
cpufreq_userspace 3172 0
cpufreq_stats 3776 0
cpufreq_powersave 1856 0
cpufreq_ondemand 6476 2
freq_table 4224 3 acpi_cpufreq,cpufreq_stats,cpufreq_ondemand
cpufreq_conservative 5960 0
nfsd 186672 17
auth_rpcgss 33952 1 nfsd
exportfs 3904 1 nfsd
nfs 214024 0
lockd 54568 2 nfsd,nfs
nfs_acl 2912 2 nfsd,nfs
sunrpc 162528 15 nfsd,auth_rpcgss,nfs,lockd,nfs_acl
ipt_ULOG 6820 4
ipt_MASQUERADE 2592 1
nf_nat_irc 2080 0
nf_nat_ftp 2528 0
ipt_REJECT 2784 1
xt_state 2016 9
nf_conntrack_irc 5124 1 nf_nat_irc
nf_conntrack_ftp 6852 1 nf_nat_ftp
xt_tcpudp 2816 8
iptable_mangle 2688 0
iptable_nat 4680 1
nf_nat 15544 4 ipt_MASQUERADE,nf_nat_irc,nf_nat_ftp,iptable_nat
nf_conntrack_ipv4 12268 12 iptable_nat,nf_nat
nf_conntrack 55540 9
ipt_MASQUERADE,nf_nat_irc,nf_nat_ftp,xt_state,nf_conntrack_irc,nf_conntrack_ftp,iptable_nat,nf_nat,nf_conntrack_ipv4
iptable_filter 2624 1
ip_tables 10160 3 iptable_mangle,iptable_nat,iptable_filter
x_tables 13284 7
ipt_ULOG,ipt_MASQUERADE,ipt_REJECT,xt_state,xt_tcpudp,iptable_nat,ip_tables
ipv6 235364 40
ext2 54504 1
fuse 42908 1
floppy 47748 0
sg 26964 0
coretemp 5504 0
it87 17904 0
hwmon_vid 2720 1 it87
snd_hda_intel 325688 3
snd_intel8x0 26268 0
snd_ac97_codec 88484 1 snd_intel8x0
ac97_bus 1728 1 snd_ac97_codec
snd_pcm_oss 32832 0
snd_mixer_oss 12320 1 snd_pcm_oss
snd_usb_audio 70304 1
snd_usb_lib 13440 1 snd_usb_audio
snd_pcm 62596 5
snd_hda_intel,snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_usb_audio
snd_hwdep 6212 1 snd_usb_audio
snd_seq_dummy 2660 0
snd_seq_oss 24992 0
snd_seq_midi 5728 0
joydev 8480 0
snd_rawmidi 18528 2 snd_usb_lib,snd_seq_midi
uvcvideo 45704 0
snd_seq_midi_event 6432 2 snd_seq_oss,snd_seq_midi
compat_ioctl32 1312 1 uvcvideo
snd_seq 41456 6
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
i2c_i801 7920 0
videodev 27520 1 uvcvideo
snd_timer 17800 2 snd_pcm,snd_seq
snd_seq_device 6380 5
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
usblp 10592 0
pl2303 14596 0
usbserial 26472 1 pl2303
v4l1_compat 12260 2 uvcvideo,videodev
wacom 15776 0
snd 45604 21
snd_hda_intel,snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_usb_audio,snd_pcm,snd_hwdep,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
pcspkr 2432 0
psmouse 32336 0
i2c_core 19828 2 nvidia,i2c_i801
soundcore 6368 1 snd
shpchp 25528 0
snd_page_alloc 7816 3 snd_hda_intel,snd_intel8x0,snd_pcm
pci_hotplug 23460 1 shpchp
serio_raw 4740 0
button 6096 0
evdev 8000 5
ext3 105512 5
jbd 39444 1 ext3
mbcache 7108 2 ext2,ext3
ide_cd_mod 27652 0
cdrom 30176 1 ide_cd_mod
ide_pci_generic 3908 0 [permanent]
usbhid 35904 0
hid 33184 1 usbhid
ff_memless 4392 1 usbhid
sd_mod 22200 9
ata_generic 4676 0
usb_storage 77024 0
ohci_hcd 18500 0
uhci_hcd 18672 0
ohci1394 24944 0
ieee1394 75800 1 ohci1394
skge 33360 0
aic7xxx 117592 7
scsi_transport_spi 19840 1 aic7xxx
ahci 23596 0
r8169 23684 0
jmicron 2208 0 [permanent]
ide_core 96136 3 ide_cd_mod,ide_pci_generic,jmicron
libata 140416 2 ata_generic,ahci
scsi_mod 129324 6
sg,sd_mod,usb_storage,aic7xxx,scsi_transport_spi,libata
dock 8304 1 libata
ehci_hcd 28396 0
usbcore 118224 13
snd_usb_audio,snd_usb_lib,uvcvideo,usblp,pl2303,usbserial,wacom,usbhid,usb_storage,ohci_hcd,uhci_hcd,ehci_hcd
intel_agp 22556 0
agpgart 28776 2 nvidia,intel_agp
thermal 15228 0
processor 32544 2 acpi_cpufreq,thermal
fan 4164 0
thermal_sys 10856 3 thermal,processor,fan
dm_mirror 15104 0
dm_log 8484 1 dm_mirror
dm_mod 46184 2 dm_mirror,dm_log
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82G33/G31/P35/P31 Express DRAM
Controller [8086:29c0] (rev 02)
Subsystem: Giga-byte Technology Device [1458:5000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: Intel Corporation 82G33/G31/P35/P31 Express PCI
Express Root Port [8086:29c1] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: f4000000-f7ffffff
Prefetchable memory behind bridge: 00000000e0000000-00000000efffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1a.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #4 [8086:2937] (rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at e000 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #5 [8086:2938] (rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at e100 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #6 [8086:2939] (rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at e500 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI
Controller #2 [8086:293c] (rev 02) (prog-if 20 [EHCI])
Subsystem: Giga-byte Technology Device [1458:5006]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fc105000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1b.0 Audio device [0403]: Intel Corporation 82801I (ICH9 Family) HD Audio
Controller [8086:293e] (rev 02)
Subsystem: Giga-byte Technology Device [1458:a002]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fc100000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express
Port 1 [8086:2940] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00009000-00009fff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1c.3 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express
Port 4 [8086:2946] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fc000000-fc0fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1c.4 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express
Port 5 [8086:2948] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: f8000000-f9ffffff
Prefetchable memory behind bridge: 00000000fc200000-00000000fc2fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1d.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #1 [8086:2934] (rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at e200 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #2 [8086:2935] (rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at e300 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #3 [8086:2936] (rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at e400 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI
Controller #1 [8086:293a] (rev 02) (prog-if 20 [EHCI])
Subsystem: Giga-byte Technology Device [1458:5006]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fc104000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev
92) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=05, subordinate=06, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fa000000-fbffffff
Prefetchable memory behind bridge: 00000000fc300000-00000000fc3fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801IB (ICH9) LPC Interface
Controller [8086:2918] (rev 02)
Subsystem: Giga-byte Technology Device [1458:5001]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 SATA controller [0106]: Intel Corporation 82801IB (ICH9) 4 port SATA
AHCI Controller [8086:2923] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Giga-byte Technology Device [1458:b005]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 219
Region 0: I/O ports at e600 [size=8]
Region 1: I/O ports at e700 [size=4]
Region 2: I/O ports at e800 [size=8]
Region 3: I/O ports at e900 [size=4]
Region 4: I/O ports at ea00 [size=32]
Region 5: Memory at fc106000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 82801I (ICH9 Family) SMBus Controller
[8086:2930] (rev 02)
Subsystem: Giga-byte Technology Device [1458:5001]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fc107000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 0500 [size=32]
Kernel driver in use: i801_smbus
01:00.0 VGA compatible controller [0300]: nVidia Corporation G86 [GeForce 8500
GT] [10de:0421] (rev a1) (prog-if 00 [VGA controller])
Subsystem: Micro-Star International Co., Ltd. Device [1462:0921]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f6000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at f4000000 (64-bit, non-prefetchable) [size=32M]
Region 5: I/O ports at a000 [size=128]
[virtual] Expansion ROM at f7000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: nvidia
03:00.0 SATA controller [0106]: JMicron Technology Corp. 20360/20363 Serial ATA
Controller [197b:2363] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Giga-byte Technology GA-EP45-DS5 Motherboard [1458:b000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 5: Memory at fc000000 (32-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: ahci
03:00.1 IDE interface [0101]: JMicron Technology Corp. 20360/20363 Serial ATA
Controller [197b:2363] (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: Giga-byte Technology GA-EP45-DS5 Motherboard [1458:b000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 16
Region 0: I/O ports at b000 [size=8]
Region 1: I/O ports at b100 [size=4]
Region 2: I/O ports at b200 [size=8]
Region 3: I/O ports at b300 [size=4]
Region 4: I/O ports at b400 [size=16]
Capabilities: <access denied>
Kernel driver in use: JMicron IDE
04:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 01)
Subsystem: Giga-byte Technology GA-EP45-DS5 Motherboard [1458:e000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 218
Region 0: I/O ports at c000 [size=256]
Region 2: Memory at f9000000 (64-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at fc200000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: r8169
05:00.0 SCSI storage controller [0100]: Adaptec AIC-7892A U160/m [9005:0080]
(rev 02)
Subsystem: Adaptec 29160 Ultra160 SCSI Controller [9005:e2a0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (10000ns min, 6250ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 20
BIST result: 00
Region 0: I/O ports at d000 [disabled] [size=256]
Region 1: Memory at fb104000 (64-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at fc300000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: aic7xxx
05:01.0 PCI bridge [0604]: Hint Corp HB6 Universal PCI-PCI bridge
(non-transparent mode) [3388:0021] (rev 15) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Bus: primary=05, secondary=06, subordinate=06, sec-latency=32
Memory behind bridge: fb000000-fb0fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
05:02.0 Ethernet controller [0200]: 3Com Corporation 3c940 10/100/1000Base-T
[Marvell] [10b7:1700] (rev 10)
Subsystem: 3Com Corporation 3C941 Gigabit LOM Ethernet Adapter
[10b7:0020]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (5750ns min, 7750ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fb100000 (32-bit, non-prefetchable) [size=16K]
Region 1: I/O ports at d100 [size=256]
[virtual] Expansion ROM at fc320000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: skge
06:08.0 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 41)
(prog-if 10 [OHCI])
Subsystem: Adaptec Device [9004:1135]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (250ns min, 10500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at fb007000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
06:08.1 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 41)
(prog-if 10 [OHCI])
Subsystem: Adaptec Device [9004:1135]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (250ns min, 10500ns max), Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 18
Region 0: Memory at fb004000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
06:08.2 USB Controller [0c03]: NEC Corporation USB 2.0 [1033:00e0] (rev 02)
(prog-if 20 [EHCI])
Subsystem: Adaptec Device [9004:11e0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (4000ns min, 8500ns max), Cache Line Size: 32 bytes
Interrupt: pin C routed to IRQ 16
Region 0: Memory at fb005000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
06:0c.0 FireWire (IEEE 1394) [0c00]: Texas Instruments TSB43AB23
IEEE-1394a-2000 Controller (PHY/Link) [104c:8024] (prog-if 10 [OHCI])
Subsystem: Texas Instruments Device [104c:8010]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (750ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at fb006000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at fb000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: ohci1394
-- System Information:
Debian Release: squeeze/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 2.6.26-2-686 (SMP w/2 CPU cores)
Locale: LANG=fr_FR.UTF-8, LC_CTYPE=fr_FR.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-2-686 depends on:
ii debconf [debconf-2.0] 1.5.26 Debian configuration management sy
ii initramfs-tools [linux-initra 0.93.3 tools for generating an initramfs
ii module-init-tools 3.7-pre9-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.26-2-686 recommends:
ii libc6-i686 2.9-12 GNU C Library: Shared libraries [i
Versions of packages linux-image-2.6.26-2-686 suggests:
ii grub 0.97-53 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.26 <none> (no description available)
-- debconf information:
linux-image-2.6.26-2-686/postinst/bootloader-error-2.6.26-2-686:
linux-image-2.6.26-2-686/postinst/bootloader-test-error-2.6.26-2-686:
linux-image-2.6.26-2-686/postinst/depmod-error-2.6.26-2-686: false
linux-image-2.6.26-2-686/preinst/bootloader-initrd-2.6.26-2-686: true
linux-image-2.6.26-2-686/postinst/create-kimage-link-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/initrd-2.6.26-2-686:
linux-image-2.6.26-2-686/postinst/kimage-is-a-directory:
linux-image-2.6.26-2-686/postinst/old-initrd-link-2.6.26-2-686: true
linux-image-2.6.26-2-686/prerm/removing-running-kernel-2.6.26-2-686: true
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.26-2-686/postinst/old-dir-initrd-link-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/overwriting-modules-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/abort-overwrite-2.6.26-2-686:
linux-image-2.6.26-2-686/preinst/abort-install-2.6.26-2-686:
linux-image-2.6.26-2-686/postinst/depmod-error-initrd-2.6.26-2-686: false
linux-image-2.6.26-2-686/preinst/failed-to-move-modules-2.6.26-2-686:
linux-image-2.6.26-2-686/preinst/lilo-has-ramdisk:
linux-image-2.6.26-2-686/prerm/would-invalidate-boot-loader-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/elilo-initrd-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/lilo-initrd-2.6.26-2-686: true
linux-image-2.6.26-2-686/postinst/old-system-map-link-2.6.26-2-686: true
--- End Message ---
