Package: linux-image-2.6.26-2-686
Version: 2.6.26-17
Severity: normal
*** Please type your report below this line ***
I have pcmcia sata card working on chipset Silicon Image Sil 3512. My previous
distribution
was Kubutu Jaunty. Under Debian Lenny Pioneer dvd-writer connected to this
card not working.
On Kubuntu everything working fine.
-- Package-specific info:
** Version:
Linux version 2.6.26-2-686 (Debian 2.6.26-17) (da...@debian.org) (gcc version
4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Sun Jun 21 04:57:38 UTC
2009
** Command line:
root=/dev/sda1 ro quiet
** Not tainted
** Kernel log:
[ 41.792026] ata4: link is slow to respond, please be patient (ready=-19)
[ 71.472024] ata4: COMRESET failed (errno=-16)
[ 76.496026] ata4: COMRESET failed (errno=-16)
[ 76.496098] ata4: reset failed, giving up
[ 76.816081] ata5: SATA link down (SStatus 0 SControl 310)
[ 77.736012] Adding 1951888k swap on /dev/sda3. Priority:-1 extents:1
across:1951888k
[ 78.117075] EXT3 FS on sda1, internal journal
[ 78.308838] loop: module loaded
[ 79.292071] fuse init (API version 7.9)
[ 79.344043] kjournald starting. Commit interval 5 seconds
[ 79.344075] EXT3 FS on sda5, internal journal
[ 79.344075] EXT3-fs: mounted filesystem with ordered data mode.
[ 79.344430] kjournald starting. Commit interval 5 seconds
[ 79.344462] EXT3 FS on sda6, internal journal
[ 79.344462] EXT3-fs: mounted filesystem with ordered data mode.
[ 82.421242] NET: Registered protocol family 10
[ 82.421592] lo: Disabled Privacy Extensions
[ 82.622224] lp: driver loaded but no devices found
[ 82.637025] ppdev: user-space parallel port driver
[ 85.880544] input: b43-phy0 as /class/input/input8
[ 85.968068] firmware: requesting b43/ucode5.fw
[ 86.060298] firmware: requesting b43/pcm5.fw
[ 86.072580] firmware: requesting b43/b0g0initvals5.fw
[ 86.079677] firmware: requesting b43/b0g0bsinitvals5.fw
[ 86.200044] b43-phy0: Loading firmware version 410.2160 (2007-05-26
15:32:10)
[ 87.524473] Registered led device: b43-phy0::tx
[ 87.524492] Registered led device: b43-phy0::rx
[ 87.524508] Registered led device: b43-phy0::radio
[ 87.576259] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 87.983794] Bluetooth: Core ver 2.11
[ 87.984953] NET: Registered protocol family 31
[ 87.984958] Bluetooth: HCI device and connection manager initialized
[ 87.984961] Bluetooth: HCI socket layer initialized
[ 88.001570] Bluetooth: L2CAP ver 2.9
[ 88.001575] Bluetooth: L2CAP socket layer initialized
[ 88.249126] Bluetooth: RFCOMM socket layer initialized
[ 88.249140] Bluetooth: RFCOMM TTY layer initialized
[ 88.249141] Bluetooth: RFCOMM ver 1.8
[ 88.695197] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 91.011429] input: b43-phy0 as /class/input/input9
[ 91.208034] b43-phy0: Loading firmware version 410.2160 (2007-05-26
15:32:10)
[ 92.087257] [drm] Initialized drm 1.1.0 20060810
[ 92.093782] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) ->
IRQ 16
[ 92.093792] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 92.093869] [drm] Initialized i915 1.6.0 20060119 on minor 0
[ 93.296496] Registered led device: b43-phy0::tx
[ 93.296518] Registered led device: b43-phy0::rx
[ 93.296534] Registered led device: b43-phy0::radio
[ 93.348287] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 94.972100] wlan0: Initial auth_alg=0
[ 94.972107] wlan0: authenticate with AP 00:21:27:e3:95:e8
[ 94.972577] wlan0: Initial auth_alg=0
[ 94.972582] wlan0: authenticate with AP 00:21:27:e3:95:e8
[ 94.973545] wlan0: RX authentication from 00:21:27:e3:95:e8 (alg=0
transaction=2 status=0)
[ 94.973550] wlan0: authenticated
[ 94.973553] wlan0: associate with AP 00:21:27:e3:95:e8
[ 94.980009] wlan0: authentication frame received from 00:21:27:e3:95:e8,
but not in authenticate state - ignored
[ 94.980074] wlan0: RX AssocResp from 00:21:27:e3:95:e8 (capab=0x431
status=0 aid=1)
[ 94.980074] wlan0: associated
[ 94.980074] wlan0: switched to short barker preamble
(BSSID=00:21:27:e3:95:e8)
[ 94.980074] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 98.401097] atkbd.c: Unknown key pressed (translated set 2, code 0xf8 on
isa0060/serio0).
[ 98.401097] atkbd.c: Use 'setkeycodes e078 <keycode>' to make it known.
[ 98.408480] atkbd.c: Unknown key released (translated set 2, code 0xf8 on
isa0060/serio0).
[ 98.408480] atkbd.c: Use 'setkeycodes e078 <keycode>' to make it known.
[ 105.944017] wlan0: no IPv6 routers present
[ 1211.714650] ACPI: PCI interrupt for device 0000:10:00.0 disabled
[ 1266.317819] sata_sil 0000:10:00.0: version 2.3
[ 1266.317864] ACPI: PCI Interrupt 0000:10:00.0[A] -> GSI 22 (level, low) ->
IRQ 22
[ 1266.317881] sata_sil 0000:10:00.0: cache line size not set. Driver may not
function
[ 1266.319575] scsi5 : sata_sil
[ 1266.321109] scsi6 : sata_sil
[ 1266.321162] ata6: SATA max UDMA/100 mmio m...@0x88480000 tf 0x88480080 irq
22
[ 1266.321167] ata7: SATA max UDMA/100 mmio m...@0x88480000 tf 0x884800c0 irq
22
[ 1271.680032] ata6: link is slow to respond, please be patient (ready=-19)
[ 1276.328031] ata6: COMRESET failed (errno=-16)
[ 1281.688038] ata6: link is slow to respond, please be patient (ready=-19)
[ 1286.336038] ata6: COMRESET failed (errno=-16)
[ 1291.712040] ata6: link is slow to respond, please be patient (ready=-19)
[ 1321.392033] ata6: COMRESET failed (errno=-16)
[ 1326.416045] ata6: COMRESET failed (errno=-16)
[ 1326.416054] ata6: reset failed, giving up
[ 1326.736116] ata7: SATA link down (SStatus 0 SControl 310)
[ 2197.529439] ACPI: PCI interrupt for device 0000:10:00.0 disabled
[ 2251.416437] sata_sil 0000:10:00.0: version 2.3
[ 2251.416478] ACPI: PCI Interrupt 0000:10:00.0[A] -> GSI 22 (level, low) ->
IRQ 22
[ 2251.416496] sata_sil 0000:10:00.0: cache line size not set. Driver may not
function
[ 2251.417560] scsi7 : sata_sil
[ 2251.418683] scsi8 : sata_sil
[ 2251.418730] ata8: SATA max UDMA/100 mmio m...@0x88480000 tf 0x88480080 irq
22
[ 2251.418734] ata9: SATA max UDMA/100 mmio m...@0x88480000 tf 0x884800c0 irq
22
[ 2256.776035] ata8: link is slow to respond, please be patient (ready=-19)
[ 2261.424044] ata8: COMRESET failed (errno=-16)
[ 2266.784054] ata8: link is slow to respond, please be patient (ready=-19)
[ 2271.432126] ata8: COMRESET failed (errno=-16)
[ 2276.792106] ata8: link is slow to respond, please be patient (ready=-19)
[ 2306.484046] ata8: COMRESET failed (errno=-16)
[ 2311.508055] ata8: COMRESET failed (errno=-16)
[ 2311.508064] ata8: reset failed, giving up
[ 2311.828063] ata9: SATA link down (SStatus 0 SControl 310)
** Loaded modules:
Module Size Used by
sata_sil 7176 0
i915 25280 2
drm 65192 3 i915
binfmt_misc 7528 1
rfcomm 28272 0
l2cap 17248 5 rfcomm
bluetooth 44868 4 rfcomm,l2cap
rfkill_input 3520 0
ppdev 6500 0
parport_pc 22500 0
lp 8164 0
parport 30988 3 ppdev,parport_pc,lp
ipv6 235364 16
cpufreq_ondemand 6476 0
cpufreq_powersave 1856 0
cpufreq_stats 3776 0
cpufreq_conservative 5960 0
cpufreq_userspace 3172 0
freq_table 4224 2 cpufreq_ondemand,cpufreq_stats
fuse 42908 1
sbp2 18572 0
loop 12748 0
joydev 8480 0
nsc_ircc 13616 0
irda 95512 1 nsc_ircc
crc_ccitt 2080 1 irda
pcspkr 2432 0
serio_raw 4740 0
psmouse 32336 0
arc4 1824 2
i2c_i801 7920 0
i2c_core 19828 1 i2c_i801
tifm_7xx1 5216 0
tifm_core 7548 1 tifm_7xx1
ecb 2624 2
crypto_blkcipher 15236 1 ecb
yenta_socket 20620 2
rsrc_nonstatic 9504 1 yenta_socket
snd_hda_intel 325688 2
snd_pcm_oss 32832 0
snd_mixer_oss 12320 1 snd_pcm_oss
snd_pcm 62596 2 snd_hda_intel,snd_pcm_oss
b43 110748 0
snd_seq_dummy 2660 0
rfkill 5652 3 rfkill_input,b43
rng_core 3940 1 b43
snd_seq_oss 24992 0
mac80211 139712 1 b43
snd_seq_midi 5728 0
cfg80211 21576 1 mac80211
snd_rawmidi 18528 1 snd_seq_midi
input_polldev 3752 1 b43
snd_seq_midi_event 6432 2 snd_seq_oss,snd_seq_midi
snd_seq 41456 6
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 17800 2 snd_pcm,snd_seq
snd_seq_device 6380 5
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
snd 45604 13
snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
soundcore 6368 1 snd
snd_page_alloc 7816 2 snd_hda_intel,snd_pcm
battery 10180 0
ac 4196 0
container 3456 0
video 16432 0
output 2912 1 video
button 6096 0
intel_agp 22556 1
agpgart 28776 3 drm,intel_agp
acer_wmi 8852 0
led_class 3908 2 b43,acer_wmi
evdev 8000 8
wmi 6440 1 acer_wmi
ext3 105512 3
jbd 39444 1 ext3
mbcache 7108 1 ext3
ide_cd_mod 27652 0
cdrom 30176 1 ide_cd_mod
ata_generic 4676 0
sd_mod 22200 5
usbhid 35904 0
hid 33184 1 usbhid
ff_memless 4392 1 usbhid
piix 6568 0 [permanent]
ahci 23596 4
libata 140416 3 sata_sil,ata_generic,ahci
scsi_mod 129324 3 sbp2,sd_mod,libata
dock 8304 1 libata
ide_pci_generic 3908 0 [permanent]
ide_core 96136 3 ide_cd_mod,piix,ide_pci_generic
sdhci 13060 0
mmc_core 39900 1 sdhci
ohci1394 24944 0
ieee1394 75800 2 sbp2,ohci1394
ssb 33476 1 b43
pcmcia 29548 2 b43,ssb
pcmcia_core 31892 5 yenta_socket,rsrc_nonstatic,b43,ssb,pcmcia
firmware_class 6816 2 b43,pcmcia
tg3 84708 0
ehci_hcd 28396 0
uhci_hcd 18672 0
usbcore 118224 4 usbhid,ehci_hcd,uhci_hcd
thermal 15228 0
processor 32544 2 thermal
fan 4164 0
thermal_sys 10856 4 video,thermal,processor,fan
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile PM965/GM965/GL960 Memory
Controller Hub [8086:2a00] (rev 03)
Subsystem: Acer Incorporated [ALI] Device [1025:011f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort+
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile GM965/GL960
Integrated Graphics Controller [8086:2a02] (rev 03) (prog-if 00 [VGA
controller])
Subsystem: Acer Incorporated [ALI] Device [1025:011f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fc000000 (64-bit, non-prefetchable) [size=1M]
Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 1800 [size=8]
Capabilities: <access denied>
Kernel modules: intelfb
00:02.1 Display controller [0380]: Intel Corporation Mobile GM965/GL960
Integrated Graphics Controller [8086:2a03] (rev 03)
Subsystem: Acer Incorporated [ALI] Device [1025:011f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at fc100000 (64-bit, non-prefetchable) [size=1M]
Capabilities: <access denied>
00:1a.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI
Controller #4 [8086:2834] (rev 03) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI] Device [1025:011f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 1820 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI
Controller #5 [8086:2835] (rev 03) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI] Device [1025:011f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 1840 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2
EHCI Controller #2 [8086:283a] (rev 03) (prog-if 20 [EHCI])
Subsystem: Acer Incorporated [ALI] Device [1025:011f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 20
Region 0: Memory at fc504800 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1b.0 Audio device [0403]: Intel Corporation 82801H (ICH8 Family) HD Audio
Controller [8086:284b] (rev 03)
Subsystem: Acer Incorporated [ALI] Realtek ALC268 audio codec
[1025:011f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at fc300000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express
Port 1 [8086:283f] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=03, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f6000000-f7ffffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f1ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.1 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express
Port 2 [8086:2841] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=05, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: f8000000-f9ffffff
Prefetchable memory behind bridge: 00000000f2000000-00000000f3ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.2 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express
Port 3 [8086:2843] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=06, subordinate=07, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: fa000000-fbffffff
Prefetchable memory behind bridge: 00000000f4000000-00000000f5ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1d.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI
Controller #1 [8086:2830] (rev 03) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI] Device [1025:011f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 1860 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI
Controller #2 [8086:2831] (rev 03) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI] Device [1025:011f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 1880 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI
Controller #3 [8086:2832] (rev 03) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI] Device [1025:011f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 18a0 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2
EHCI Controller #1 [8086:2836] (rev 03) (prog-if 20 [EHCI])
Subsystem: Acer Incorporated [ALI] Device [1025:011f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fc504c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge
[8086:2448] (rev f3) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=0f, subordinate=13, sec-latency=32
I/O behind bridge: 00005000-00005fff
Memory behind bridge: fc200000-fc2fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort+
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801HEM (ICH8M) LPC Interface
Controller [8086:2815] (rev 03)
Subsystem: Acer Incorporated [ALI] Device [1025:011f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel modules: iTCO_wdt
00:1f.1 IDE interface [0101]: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E)
IDE Controller [8086:2850] (rev 03) (prog-if 8a [Master SecP PriP])
Subsystem: Acer Incorporated [ALI] Device [1025:011f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 1810 [size=16]
Kernel driver in use: PIIX_IDE
Kernel modules: piix
00:1f.2 SATA controller [0106]: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E)
SATA AHCI Controller [8086:2829] (rev 03) (prog-if 01 [AHCI 1.0])
Subsystem: Acer Incorporated [ALI] Device [1025:011f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 220
Region 0: I/O ports at 1c00 [size=8]
Region 1: I/O ports at 18d4 [size=4]
Region 2: I/O ports at 18d8 [size=8]
Region 3: I/O ports at 18d0 [size=4]
Region 4: I/O ports at 18e0 [size=32]
Region 5: Memory at fc504000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 82801H (ICH8 Family) SMBus Controller
[8086:283e] (rev 03)
Subsystem: Acer Incorporated [ALI] Device [1025:011f]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 19
Region 0: Memory at 88000000 (32-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 1c20 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
02:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM5787M
Gigabit Ethernet PCI Express [14e4:1693] (rev 02)
Subsystem: Acer Incorporated [ALI] Device [1025:011c]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR+ <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 219
Region 0: Memory at f6000000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <ignored> [disabled]
Capabilities: <access denied>
Kernel driver in use: tg3
Kernel modules: tg3
04:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11b/g WLAN
[14e4:4311] (rev 01)
Subsystem: AMBIT Microsystem Corp. Device [1468:0422]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at f8000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: b43-pci-bridge
Kernel modules: ssb
0f:06.0 CardBus bridge [0607]: Texas Instruments PCIxx12 Cardbus Controller
[104c:8039]
Subsystem: Acer Incorporated [ALI] Device [1025:011f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort+
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fc204000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=0f, secondary=10, subordinate=13, sec-latency=176
Memory window 0: 88400000-887ff000 (prefetchable)
Memory window 1: 8c000000-8ffff000
I/O window 0: 00005000-000050ff
I/O window 1: 00005400-000054ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket
0f:06.1 FireWire (IEEE 1394) [0c00]: Texas Instruments PCIxx12 OHCI Compliant
IEEE 1394 Host Controller [104c:803a] (prog-if 10 [OHCI])
Subsystem: Acer Incorporated [ALI] Device [1025:011f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping-
SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fc206000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at fc200000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: ohci1394
Kernel modules: ohci1394
0f:06.2 Mass storage controller [0180]: Texas Instruments 5-in-1 Multimedia
Card Reader (SD/MMC/MS/MS PRO/xD) [104c:803b]
Subsystem: Acer Incorporated [ALI] Device [1025:011f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 57 (1750ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fc205000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: tifm_7xx1
Kernel modules: tifm_7xx1
0f:06.3 SD Host controller [0805]: Texas Instruments PCIxx12 SDA Standard
Compliant SD Host Controller [104c:803c]
Subsystem: Acer Incorporated [ALI] Device [1025:011f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 57 (1750ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fc206800 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: sdhci
Kernel modules: sdhci
10:00.0 Mass storage controller [0180]: Silicon Image, Inc. SiI 3512
[SATALink/SATARaid] Serial ATA Controller [1095:3512] (rev 01)
Subsystem: Silicon Image, Inc. SiI 3512 SATALink Controller [1095:3512]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort+
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at 5010 [size=8]
Region 1: I/O ports at 5020 [size=4]
Region 2: I/O ports at 5018 [size=8]
Region 3: I/O ports at 5024 [size=4]
Region 4: I/O ports at 5000 [size=16]
Region 5: Memory at 88480000 (32-bit, non-prefetchable) [size=512]
[virtual] Expansion ROM at 88400000 [disabled] [size=512K]
Capabilities: <access denied>
Kernel driver in use: sata_sil
Kernel modules: sata_sil
-- System Information:
Debian Release: 5.0.2
APT prefers stable
APT policy: (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 2.6.26-2-686 (SMP w/1 CPU core)
Locale: LANG=pl_PL.UTF-8, LC_CTYPE=pl_PL.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-2-686 depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration management
sy
ii initramfs-tools [linux-initra 0.92o tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel
mo
Versions of packages linux-image-2.6.26-2-686 recommends:
ii libc6-i686 2.7-18 GNU C Library: Shared libraries
[i
Versions of packages linux-image-2.6.26-2-686 suggests:
ii grub 0.97-47lenny2 GRand Unified Bootloader (Legacy
v
pn linux-doc-2.6.26 <none> (no description available)
-- debconf information:
linux-image-2.6.26-2-686/postinst/bootloader-error-2.6.26-2-686:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.26-2-686/postinst/old-dir-initrd-link-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/overwriting-modules-2.6.26-2-686: true
linux-image-2.6.26-2-686/postinst/bootloader-test-error-2.6.26-2-686:
linux-image-2.6.26-2-686/postinst/depmod-error-2.6.26-2-686: false
linux-image-2.6.26-2-686/preinst/bootloader-initrd-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/abort-overwrite-2.6.26-2-686:
linux-image-2.6.26-2-686/preinst/abort-install-2.6.26-2-686:
linux-image-2.6.26-2-686/postinst/depmod-error-initrd-2.6.26-2-686: false
linux-image-2.6.26-2-686/postinst/create-kimage-link-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/failed-to-move-modules-2.6.26-2-686:
linux-image-2.6.26-2-686/preinst/initrd-2.6.26-2-686:
linux-image-2.6.26-2-686/preinst/lilo-has-ramdisk:
linux-image-2.6.26-2-686/prerm/would-invalidate-boot-loader-2.6.26-2-686:
true
linux-image-2.6.26-2-686/postinst/kimage-is-a-directory:
linux-image-2.6.26-2-686/postinst/old-initrd-link-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/elilo-initrd-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/lilo-initrd-2.6.26-2-686: true
linux-image-2.6.26-2-686/prerm/removing-running-kernel-2.6.26-2-686: true
linux-image-2.6.26-2-686/postinst/old-system-map-link-2.6.26-2-686: true
--
To UNSUBSCRIBE, email to debian-kernel-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
