--- Begin Message ---
Package: linux-image-2.6.22-3-686
Version: 2.6.22-6
Severity: important
The i810fb module depends on agpgart module, but intel-agp module needs
to be loaded before agpgart (and therefore i810fb) will use it. From
searching the Web and the BTS, this seems to apply to intelfb as well.
Relevant part from the output of 'lsmod":
---
i810fb 30652 1
intel_agp 23188 1
agpgart 31912 3 i810fb,intel_agp
---
To make the framebuffer work, I had to add a file to /etc/modprobe.d/
to force loading the modules in the correct order.
Contents of '/etc/modprobe.d/i810fb':
---
install /sbin/modprobe intel-agp; /sbin/modprobe --ignore-install i810fb
---
Shouldn't intel-agp be loaded as a dependency of i810fb (or by
udev/modprobe using a module alias)?
-Alain
-- Package-specific info:
** Version:
Linux version 2.6.22-3-686 (Debian 2.6.22-6) (m...@debian.org) (gcc version
4.1.3 20071019 (prerelease) (Debian 4.1.2-17)) #1 SMP Mon Nov 12 08:32:57 UTC
2007
** Not tainted
** Kernel log:
swsusp: Basic memory bitmaps created
swsusp: Basic memory bitmaps freed
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Yenta: CardBus bridge found at 0000:01:07.0 [1043:1404]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:01:07.0, mfunc 0x10004002, devctl 0x66
intel_rng: FWH not detected
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
iTCO_wdt: Found a ICH2-M TCO device (Version=1, TCOBASE=0xe460)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
Yenta: ISA IRQ mask 0x00e8, PCI irq 11
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#01) from #01 to #05
pcmcia: parent PCI bridge I/O window: 0xd000 - 0xdfff
cs: IO port probe 0xd000-0xdfff: clean.
pcmcia: parent PCI bridge Memory window: 0xf4800000 - 0xf77fffff
pcmcia: parent PCI bridge Memory window: 0x20000000 - 0x27ffffff
Yenta: CardBus bridge found at 0000:01:07.1 [1043:1404]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:01:07.1, mfunc 0x10004002, devctl 0x66
spurious 8259A interrupt: IRQ7.
Yenta: ISA IRQ mask 0x00e8, PCI irq 11
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#01) from #05 to #09
pcmcia: parent PCI bridge I/O window: 0xd000 - 0xdfff
cs: IO port probe 0xd000-0xdfff: clean.
pcmcia: parent PCI bridge Memory window: 0xf4800000 - 0xf77fffff
pcmcia: parent PCI bridge Memory window: 0x20000000 - 0x27ffffff
input: PC Speaker as /class/input/input1
Real Time Clock Driver v1.12ac
irda_init()
NET: Registered protocol family 23
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 10 (level, low) ->
IRQ 10
PCI: Setting latency timer of device 0000:00:1f.5 to 64
Synaptics Touchpad, model: 1, fw: 4.6, id: 0x925ea1, caps: 0x80471b/0x0
input: SynPS/2 Synaptics TouchPad as /class/input/input2
parport_pc 00:0a: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
nsc_ircc_pnp_probe() : From PnP, found firbase 0x2F8 ; irq 3 ; dma 1.
nsc-ircc, chip->init
nsc-ircc, Found chip at base=0x02e
nsc-ircc, driver loaded (Dag Brattli)
nsc_ircc_open(), can't get iobase of 0x2f8
nsc-ircc, Found chip at base=0x02e
nsc-ircc, driver loaded (Dag Brattli)
nsc_ircc_open(), can't get iobase of 0x2f8
pnp: Device 00:0b disabled.
intel8x0_measure_ac97_clock: measured 55139 usecs
intel8x0: clocking to 48000
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 10 (level, low) ->
IRQ 10
PCI: Setting latency timer of device 0000:00:1f.6 to 64
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
Adding 859436k swap on /dev/hda5. Priority:-1 extents:1 across:859436k
EXT3 FS on hda1, internal journal
loop: module loaded
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Marking TSC unstable due to: cpufreq changes.
Time: acpi_pm clocksource has been installed.
ACPI: Battery Slot [BAT0] (battery present)
ACPI: AC Adapter [AC] (on-line)
input: Power Button (FF) as /class/input/input3
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /class/input/input4
ACPI: Lid Switch [LID]
input: Power Button (CM) as /class/input/input5
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /class/input/input6
ACPI: Sleep Button (CM) [SLPB]
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
Clocksource tsc unstable (delta = -142895742 ns)
eth0: no IPv6 routers present
serial8250: too much work for irq3
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
eth0: no IPv6 routers present
** Loaded modules:
Module Size Used by
rfcomm 36280 2
l2cap 22432 9 rfcomm
bluetooth 49348 4 rfcomm,l2cap
ppdev 8676 0
lp 10980 0
button 7920 0
ac 5188 0
battery 9988 0
speedstep_ich 5328 0
speedstep_lib 5156 1 speedstep_ich
cpufreq_userspace 4128 0
cpufreq_conservative 6888 0
cpufreq_stats 5120 0
cpufreq_powersave 1792 0
cpufreq_ondemand 8300 1
freq_table 4512 3 speedstep_ich,cpufreq_stats,cpufreq_ondemand
ipv6 236996 18
loop 16932 0
firewire_sbp2 12100 0
joydev 9568 0
tsdev 7968 0
pcmcia 37100 0
firmware_class 9504 1 pcmcia
snd_intel8x0m 16684 0
snd_intel8x0 32124 0
snd_ac97_codec 92836 2 snd_intel8x0m,snd_intel8x0
ac97_bus 2272 1 snd_ac97_codec
snd_pcm_oss 39200 0
snd_pcm 72324 4
snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm_oss
snd_mixer_oss 15424 1 snd_pcm_oss
snd_seq_midi 8160 0
irda 172092 0
serio_raw 6692 0
crc_ccitt 2144 1 irda
parport_pc 33828 1
parport 33960 3 ppdev,lp,parport_pc
snd_rawmidi 22624 1 snd_seq_midi
snd_seq_dummy 3748 0
rtc 12856 0
pcspkr 3104 0
psmouse 36016 0
snd_seq_oss 29408 0
snd_seq_midi_event 6880 2 snd_seq_midi,snd_seq_oss
snd_seq 46320 6
snd_seq_midi,snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
snd_timer 21028 2 snd_pcm,snd_seq
snd_seq_device 7692 5
snd_seq_midi,snd_rawmidi,snd_seq_dummy,snd_seq_oss,snd_seq
iTCO_wdt 9924 0
snd 48324 11
snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_pcm,snd_mixer_oss,snd_rawmidi,snd_seq_oss,snd_seq,snd_timer,snd_seq_device
yenta_socket 24844 2
rsrc_nonstatic 11968 1 yenta_socket
soundcore 7520 1 snd
snd_page_alloc 10056 3 snd_intel8x0m,snd_intel8x0,snd_pcm
pcmcia_core 37108 3 pcmcia,yenta_socket,rsrc_nonstatic
shpchp 31060 0
pci_hotplug 29184 1 shpchp
evdev 9312 6
ext3 121288 1
jbd 55336 1 ext3
mbcache 8260 1 ext3
ide_disk 16512 3
ata_generic 7556 0
libata 115984 1 ata_generic
scsi_mod 136620 2 firewire_sbp2,libata
uhci_hcd 22960 0
piix 8868 0 [permanent]
usbcore 125416 2 uhci_hcd
generic 4836 0 [permanent]
ide_core 113764 3 ide_disk,piix,generic
firewire_ohci 16512 0
firewire_core 39008 2 firewire_sbp2,firewire_ohci
crc_itu_t 2144 1 firewire_core
8139too 25536 0
8139cp 22144 0
mii 5280 2 8139too,8139cp
thermal 13416 0
processor 31176 1 thermal
fan 4836 0
i810fb 30652 1
intel_agp 23188 1
agpgart 31912 3 i810fb,intel_agp
vgastate 8256 1 i810fb
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82815 815 Chipset Host Bridge and
Memory Controller Hub [8086:1130] (rev 11)
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:1402]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: <access denied>
00:02.0 VGA compatible controller [0300]: Intel Corporation 82815 CGC [Chipset
Graphics Controller] [8086:1132] (rev 11) (prog-if 00 [VGA])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:1402]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at f7800000 (32-bit, non-prefetchable) [size=512K]
Capabilities: <access denied>
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge
[8086:2448] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=09, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: f4800000-f77fffff
Prefetchable memory behind bridge: 20000000-27ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge [0601]: Intel Corporation 82801BAM ISA Bridge (LPC)
[8086:244c] (rev 03)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface [0101]: Intel Corporation 82801BAM IDE U100 [8086:244a]
(rev 03) (prog-if 80 [Master])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:1402]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[disabled] [size=1]
Region 4: I/O ports at b800 [size=16]
00:1f.2 USB Controller [0c03]: Intel Corporation 82801BA/BAM USB (Hub #1)
[8086:2442] (rev 03) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:1402]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at b400 [size=32]
00:1f.4 USB Controller [0c03]: Intel Corporation 82801BA/BAM USB (Hub #2)
[8086:2444] (rev 03) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:1402]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 9
Region 4: I/O ports at b000 [size=32]
00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801BA/BAM AC'97
Audio [8086:2445] (rev 03)
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:1463]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 10
Region 0: I/O ports at e000 [size=256]
Region 1: I/O ports at e100 [size=64]
00:1f.6 Modem [0703]: Intel Corporation 82801BA/BAM AC'97 Modem [8086:2446]
(rev 03) (prog-if 00 [Generic])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:1406]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 10
Region 0: I/O ports at e500 [size=256]
Region 1: I/O ports at e300 [size=128]
01:04.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:1045]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 4
Region 0: I/O ports at d800 [size=256]
Region 1: Memory at f7000000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
01:07.0 CardBus bridge [0607]: Texas Instruments PCI4451 PC card Cardbus
Controller [104c:ac42]
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:1404]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f4804000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=01, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 20000000-23fff000 (prefetchable)
Memory window 1: 28000000-2bfff000
I/O window 0: 0000d000-0000d0ff
I/O window 1: 0000d400-0000d4ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
01:07.1 CardBus bridge [0607]: Texas Instruments PCI4451 PC card Cardbus
Controller [104c:ac42]
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:1404]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f4805000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=01, secondary=06, subordinate=09, sec-latency=176
Memory window 0: 24000000-27fff000 (prefetchable)
Memory window 1: 2c000000-2ffff000
I/O window 0: 0000dc00-0000dcff
I/O window 1: 00001000-000010ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
01:07.2 FireWire (IEEE 1394) [0c00]: Texas Instruments PCI4451 IEEE-1394
Controller [104c:8027] (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:1407]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f4806000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at f4800000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
-- System Information:
Debian Release: lenny/sid
APT prefers testing
APT policy: (990, 'testing'), (500, 'unstable')
Architecture: i386 (i686)
Kernel: Linux 2.6.22-3-686 (SMP w/1 CPU core)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.22-3-686 depends on:
ii initramfs-tools [linux-initr 0.91d tools for generating an initramfs
ii module-init-tools 3.3-pre11-4 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.22-3-686 recommends:
ii libc6-i686 2.7-6 GNU C Library: Shared libraries [i
-- debconf information:
linux-image-2.6.22-3-686/postinst/bootloader-test-error-2.6.22-3-686:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.22-3-686/preinst/lilo-initrd-2.6.22-3-686: true
linux-image-2.6.22-3-686/prerm/would-invalidate-boot-loader-2.6.22-3-686: true
linux-image-2.6.22-3-686/preinst/overwriting-modules-2.6.22-3-686: true
linux-image-2.6.22-3-686/preinst/elilo-initrd-2.6.22-3-686: true
linux-image-2.6.22-3-686/postinst/kimage-is-a-directory:
linux-image-2.6.22-3-686/preinst/lilo-has-ramdisk:
linux-image-2.6.22-3-686/preinst/initrd-2.6.22-3-686:
linux-image-2.6.22-3-686/postinst/old-initrd-link-2.6.22-3-686: true
linux-image-2.6.22-3-686/postinst/old-system-map-link-2.6.22-3-686: true
linux-image-2.6.22-3-686/preinst/already-running-this-2.6.22-3-686:
linux-image-2.6.22-3-686/postinst/depmod-error-2.6.22-3-686: false
linux-image-2.6.22-3-686/postinst/bootloader-error-2.6.22-3-686:
linux-image-2.6.22-3-686/preinst/failed-to-move-modules-2.6.22-3-686:
linux-image-2.6.22-3-686/postinst/old-dir-initrd-link-2.6.22-3-686: true
linux-image-2.6.22-3-686/preinst/abort-install-2.6.22-3-686:
linux-image-2.6.22-3-686/preinst/abort-overwrite-2.6.22-3-686:
linux-image-2.6.22-3-686/postinst/depmod-error-initrd-2.6.22-3-686: false
linux-image-2.6.22-3-686/preinst/bootloader-initrd-2.6.22-3-686: true
linux-image-2.6.22-3-686/prerm/removing-running-kernel-2.6.22-3-686: true
linux-image-2.6.22-3-686/postinst/create-kimage-link-2.6.22-3-686: true
--- End Message ---
